Search Documents

By M. McPherson, P. Mousset-Jones, G. Danko

Calculation of the sensible heat transfer between the rock surface and the flowing air in an underground airway is still fraught with problems. There are only a few results available in the literature for the calculation of the convection in tunnels with naturally rough surfaces. Some of them are purely empirical, while others use a theoretical approach, based on the analogy between heat and momentum transfer, expressing the heat transfer coefficient as a function of the friction factor. A review and evaluation of these results are presented. The heat transfer equations obtained using the different assumptions, vary over a wide range, so that experimental results are needed to determine the formulae and constants applicable to mine airways. In situ measurements of the "physical" and "technical" heat transfer coefficient carried out in deep mines are described. The statistical distribution of the convective heat transfer coefficient on rough surfaces, as well as the regression between the Nusselt and Reynolds numbers in the turbulent flow region, are presented. Radiative heat transfer between the surface and the moist air flowing in a duct of relatively large hydraulic diameter has been taken into account during evaluation. The results will be a definite refinement of those calculations presently used in mine climate simulation models.

Jan 1, 1987

?Energy-related systems: wind, solar, electric are typically materials intensive. As new technologies are widely deployed, significant quantities of the elements required to manufacture them will be needed. However, many of these unfamiliar elements are not presently mined, refined or traded in large quantities, and, as a result, their availability might be constrained by many complex factors. A shortage of these ?energy-critical elements? could significantly inhibit the adoption of otherwise game-changing energy technologies. This, in turn, would limit the competitiveness of the U.S. industries and the domestic scientific enterprises and, eventually, diminish the quality of life in the US.? -Energy Critical Elements: Securing Materials for Emerging Technologies?- American Physical Society, 2011.

Jan 1, 2012

By Peikun Liu, Guangyu Sun, Raja V. Ramani, Shambhu Sharan, Raman Srikanth, Bharath K. Belle

The contribution of the various outby sources to the contamination of the panel intake air has been the subject of a relatively small number of studies. In this paper, after a brief review of past studies, results from recent experiments on rates of contamination of intake air by outby dust sources are presented. Present study indicates that each outby source by itself may not be a major contributor. The loading point in the continuous miner section did not appear to be of major concern from contamination point of view. Belt entry including transfer point contributes significantly to the intake air dust level, though reentrainment was not a major source of dust. In longwall panels, the stageloader-crusher was the most dominant source. The panel-to-main belt transfer point was not a major source. Taken collectively, the contribution of all outby sources can be significant. In one longwall section, at the beginning of the longwall face, the contribution of all the outby sources and the headgate cut-out operation was observed to be about 80% of the permissible exposure limit (2 mg/m3). In modem high production longwalls, the application of effective dust control measures to reduce the dust generated from the outby sources is essential to achieve compliance with the dust standards.

Jan 1, 1997

By John Clarke Holman

Industrial growth and survival in today's competitive world means both economic efficiency and technological superiority. Superior technology includes not only exploiting the best methodologies and techniques presently available, but also a continuous search for and development of, better ones. In practical terms this translates into an investment of substantial sums of money. Of course, even a relatively small investment will not be justified if the fruits of the project cannot be secured to the investor and the inventor alike. There are at least three ways to protect new or improved technology. If the improvement reaches the height of an invention, "patenting" usually is the preferred mode of protection. If, however, the improvement is novel and valuable but does not satisfy the requirements of the patent laws, one may then consider "trade secret" agreements as a means of obtaining appropriate return for the investment made so long as the improvement is capable of being maintained in secret and cannot be "reverse engineered." If one develops a new and useful organism and seeks immediate protection from infringers, current thinking is that the copyright law may afford such protection simply by publishing the genetic code. Here is one instance where you may publish without perishing! This paper will endeavor to highlight the pros and cons of various legal mechanisms and their applicability to the frontiers of technology.

Jan 1, 1985

By Robert M. Belesky, H. R. Hardy

A methodology to detect the presence and monitor the stability of shallow cavities is presented in this paper. The approach incorporates surface-wave seismic and acoustic emission/microseismic (AEIMS) techniques. Application of tomography to the seismic data is made to enhance the ability to locate cavities. Zonal and hit-sequence location techniques are introduced into AE/MS monitoring schemes. These source location techniques simplify the analytical procedure yet still provide sufficient information regarding the region of AE/MS activity. The concept of unique velocity data for conventional, least-squares, source location routines is discussed. A hypothetical case utilizing the algorithm is presented. The method described has been successful based on preliminary studies. Areas of current and future research are identified.

Jan 1, 1986

By Z. M. Zavodni, M. K. McCarter

This paper identifies physical conditions responsible for past instability of the Main Hill area in Kennecott Copper Corporation's Bingham Canyon Mine, Bingham Canyon, Utah, and describes successful stabilization techniques employed in this slide zone. Geotechnical highlights of recent slides are presented, including monitoring, geological engineering data collection, hydrology, physical rock properties, and stability analyses. Local conditions responsible for slope movement in the Main Hill zone are: (1) high pore water pressure that causes a substantial decrease in real and effective material strengths; (2) continuous structural systems that allow sliding in the more competent rock zones; and (3) broad areas containing fractured, altered , and incompetent rock and soil- like materials. The failure mode is structurally controlled and involves a circular-type soil failure in the toe region initiated by excessive pore water pressure. A surface mapping method is presented which assigns rock mass quality on the basis of block size and rock substance strength. This site characterization technique has successfully predicted slide boundaries and failure modes; used in conjunction with laboratory determined shear strengths, it has provided basic input for calculating slope safety factors in the Main Hill slide zone.

Jan 1, 1977

By Ching L. Wu, Bolek Chytrowski, Peter Frobenius, Dale Roberts

During the past few years, the first stage of the Waste Isolation Pilot Plant, (WIPP) which consists of an exploratory shaft, a ventilation shaft, shaft stations, access drifts and test rooms, has been under construction. Construction of the first stage is scheduled to be completed in the summer of 1983. The U.S. Department of Energy (DOE) is constructing the WIPP facility to demonstrate the feasibility of disposing of defense-related nuclear waste in the bedded salt deposits of the Delaware Basin near Carlsbad, N.M. The project promises to be a proving ground for underground nuclear waste storage facility design and construction. The completed underground plant will extend over an area of 647,500 m2 (160 acres), and 1,360,500 metric tons (1,500,000 tons) of salt will be excavated. The first stage of the project, the Site and Preliminary Design Validation (SPDV) Program, provides for full-scale construction of the major components of the underground facility. Shaft construction and underground development are described. Rock bolt installation is performed as required for roof control. Geotechnical instrumentation is installed to monitor the behavior of underground openings. Direct observation of the constructed shafts, shaft stations, and underground openings is expected to confirm the adequacy of the underground design and allow full-scale construction of the first U.S. underground nuclear waste storage facility to proceed.

Jan 1, 1983

More than 5,300 mining professionals from around the world attended the SME Annual Meeting and Exhibit, March 1-3 in Denver, CO. Seventy three technical sessions highlighted innovative technologies and applications for the development of mineral resources. And the exhibit featured 421 companies worldwide and 632 exhibit booths. The 1999 SME Annual Meeting had 10% international attendance Professionals from outside the United States were guests at the first SME International Reception. Other meeting highlights included the Keynote Session. This pivotal session examined the international experience of North American-based companies. Speakers presented their perspectives on international explorations and operations. Keynote speakers included Robert Buchan, Chairman an( Chief Executive Officer, Kinross Gold; Dave Baker, Director Global Mining Project Management, Caterpillar; and Leendert Krol, Vice President International Operations Newmont Gold. Ihor Kunasz, 1998 SME President, made the introductory remarks.

Jan 1, 1999

By Winfield G. Wright, Greg P. Meeker, Philip L. Verplanck, Douglas B. Yager, Dana J. Bove, M. Alisa Mast

A really extensive acid sulfate-altered and mineralized rock in the southeast Red Mountains area is noted for its association with naturally occurring and mine-related acidic and metal-rich waters. Integrated geologic and aqueous geochemical studies demonstrate that the degree of metal mobilization and acid production in natural waters correlates well with the type of hydrothermally altered rock and structural features in which these water interact. Quartz-sericite-pyrite, quartz-alunite, and argillic alteration assemblages are associated with some of the most naturally acidic, high-metal waters in the study area; calcite-bearing propylitic rocks are related to the most pristine waters and buffer sulfate-rich, acidic waters produced by pyrite oxidation. Trace metals in natural waters are mostly derived from enargite, zinc-rich tetrahedrite and sphalerite. Pyrite oxidation contributes very little with respect to base-metals in these natural waters.

Jan 1, 2000

By Alfredo Valdivia, Hamed Nejad, Vincent Monaco, William Cao

"The East Side Access (ESA) CM005 Contract - Manhattan South Structures - consists of the installation of the waterproofing and final concrete lining for railroad tunnels, 3-Level Wye track turnout structures, segments of the Main Cavern Station, and a series of Ventilation Structures excavated beneath the existing Metro North Railroad (MNR) Grand Central Terminal. Several key team decisions made collectively by the Construction Manager (CM), Designer, and the Contractor has allowed the scheduled construction duration of 29 months to be maintained. These strategies include the use of alternate design and construction methods, including the use of pneumatically applied concrete lining and precast lining. This paper discusses these strategies, and illustrates how successful teamwork and cooperation during the execution of a large-scale construction project can lead to lowering costs, improving quality, and maintaining the overall project schedule. INTRODUCTION The East Side Access Project The Long Island Railroad (LIRR) currently transports commuters from Long Island into Manhattan, terminating at the already over congested Penn Station on the west side of Manhattan. Once completed, the ESA Project will provide LIRR commuters direct access to the east side of Manhattan underneath Grand Central Terminal. The ESA Project will help alleviate the congestion at Penn Station, which currently accommodate the NJ Transit, Amtrak, and LIRR lines; reduce travel time for LIRR passengers traveling to the east side of Manhattan and facilitate connections to the NYCT Subway System and Metro North Rail Road. The ESA Project includes building new tunnels and facilities under Manhattan and Queens. (See Figure 1).The Manhattan Alignment In the Manhattan segment of the ESA Project the excavation in hard rock of tunnels, cross passages, caverns and shafts has been completed by tunnel boring machines, drill and blast, and road header. The construction of the structural concrete final lining, interior structures and fit-out of the previously excavated caverns and tunnels are currently being performed under Contract CM005 Manhattan South Structures awarded to Michels Corporation and Contract CM006 Manhattan North Structures awarded to Frontier Kemper Constructors Inc. This paper focuses on the design and construction aspects of Contract CM005 which is the first ESA Contract in Manhattan to successfully construct concrete final linings in pre-existing excavated areas."

Jan 1, 2016

By Jean E. Kiel, Rob Dorey, Dirk J. A. van Zyl

1.1 INTRODUCTION This chapter seeks to provide an overview of important factors involved in the implementation of heap leach technology as a vehicle for gold extraction from its ores. Toward this end, brief discussions of the various elements important to this process are presented here. Topics covered in this chapter include a brief history of the process; basic chemical reactions responsible for the process ; characteristics of ores amenable to heap leaching; location of the greatest concentration of heap leach projects in the U.S.; heap leach components, methods, regulatory/permitting considerations; and economic considerations. Most of these subjects are treated at much greater length in subsequent chapters. Thus, this chapter serves as a summary for those which follow, in addition to providing the reader with a feeling for those topics which may be of most immediate interest. 1.1.1 History of the Process Modern Day Precious metal heap leaching technology has developed over the past decade, although the principles of heap leaching per se, as well as those of gold extraction through cyanidation have a long history (see discussion below). However, it is in the past 10 years that heap leaching has developed into an efficient method of treating oxidized gold and silver ores. It has proven to be both an efficient way to extract precious metals from small, shallow deposits, as well as an attractive way to treat large, low- grade, disseminated deposits. Heap leaching has several advantages compared to conventional milling (i .e., crushing, grinding, and agitation leaching). In general, these advantages include simplicity, lower capital and operating costs, shorter start-up times, and less intensive environmental regulatory concerns. A possible disadvantage of currently existing heap leach technology is a potentially lower percentage of metal extraction being obtained from the ore than would be the case with conventional milling (Potter, 1981; Hiskey, 1985; and Thorstad, 1987) The actual principle of heap leaching has a long history as inferred previously. For example, mines in Hungary recycled copper-bearing solutions through waste heaps in the mid-sixteenth century (Hiskey, 1985), and Spanish miners percolated acid solutions through large heaps of oxide copper ore on the banks of the Rio Tinto around 1752. By 1900, leaching operations were employing such techniques as leach/rest cycles to maximize copper recovery (Taylor and Whelan, 1942; Thorstad, 1987). Copper dump leaching is currently

Jan 1, 1988

By S. Su, S. Natansohn

This report describes a process for tungsten recovery from Searles Lake brines and upgrading its concentration to useful levels. The method consists of a combination of a liquid-solid and liquid-liquid extraction step and results in a product stream containing more than l00g W03/1. This technique is also effective in substantially reducing the concentration of objectionable impurities in the tungsten product. An ion exchange extraction mechanism is postulated.

Jan 1, 1983

By James W. Martin, Brad H. Droegmiller

As construction projects continue to get larger, greater demands are placed on systems to provide higher production rates at reasonable costs. This paper shows the application of dozer-trap loading versus other methods of moving bulk materials. Most conventional methods employ multiple types of heavy equipment to accomplish a single task. Trap loaders fed by dozers and discharging onto overland conveyors offer an alternative/economical means of high volume bulk material movement. This paper will discuss the process of trap loading to overland conveyors.

Jan 1, 1998

By Danny W. Hagood

High methane liberation and mining depth were two major factors which prompted the development of a high- capacity face ventilation system at Jim Walter Re- sources, Inc., No. 4 Mine. No. 4 Mine, one of four deep shaft mines presently under development, is located approximately 50 miles southwest of Birmingham, near Brookwood, Alabama (Figure 1). The coal seams under development are located in the Warrior Coal Field and include both the Blue Creek and Mary Lee Seams, Depth of cover averages 2000 ft. (610 m) with an average total mining height of 8 ft. C2.4 m). [ ] It is generally accepted that the methane content of a particular coal increases as the overburden depth is increased [l] ; experience to date has shown that the gas condition of the No. 4 Mine is no exception to the rule. To further compound the problem, the over- burden depth, coupled with the relatively soft nature of the Blue Creek coal, has resulted in an initial layout based upon 150 x 150 ft (45.7 x 45.7 m) centers. Considering the above-mentioned mining conditions, the means and the effectiveness of the face ventilation system becomes paramount where productivity is concerned.

Jan 1, 1980

By Charles D. Litton

Introduction The successful performance of a mine-wide fire detection system depends upon its ability to detect the presence of a fire rapidly and reliably. It should be sufficiently rapid so that there remains enough time to either safely evacuate a mine or successfully extinguish and control the fire or both. It should be reliable so that false alarms are minimized without sacrificing sensitivity or time response. Systems should also be durable enough to withstand the mine environment over long periods of time while maintaining a high degree of re1iability. Maintenance and calibration of the system should be simp1 e and not require the expenditure of excessive time and manpower to keep it operational. Sensitivity, reliability, and durability of mine fire sensors and their electronic support systems have been the subject of significant Bureau research within recent years. The bulk of this type of information, along with the reports from which the remainder of this paper is derived, can be found in the Bibliography. It suffices to say that there exist commercially available systems for use in mines. This paper addresses a strategy for the use of such sensors and systems. Many factors influence the design of a mine-wide fire detection system, such as the potential sources and modes of ignition, the types of combustibles involved and the quantities avai1able for fire growth and flame spread. Mine air ventilation influences the growth and spread of a fire and also serves to transport the products-of-combustion to other areas of a mine remote from the fire. Fire sensor alarm thresholds place limits on the sizes of fires that can be detected. The time to respond to a detected fire, either in terms of evacuation or control and extinguishment, place additional time constraints on the design of fire detection systems. These factors interact with each other, often in complex ways, and it is the definition and understanding of these factors and their interactions that hold the key to the design of adequate and re1iable fire detection systems. Our level of understanding of the problem has increased dramatically within recent years and it is the intent of this paper to discuss the progress that has been made and how the information can best be used to improve the level of fire detection in underground mines.

Jan 1, 1986

By Maria S. Adusumilli, A. Bhaskara Rao

ABSTRACT The presence of gold in lateritic crusts over mafic and ultramafic volcanogenic complexes in / and greenstohe belts, has called the attention in several parts of Brazil and also in Australia. Recent studies reveal the variety of structures and mineralogy of such crusts, and their importance in correlation with host(bed) rock types, as exploration guides, specially for greenstone belt metallogeny. The expected nature of growth of plates and/or nuggets in such crusts is under detailed study, and is considered as possibly due to dissolution and reprecipitation phenomenae of disseminated-fine-low grade ore in the host rock, in this investigation, laterite geochemistry, though incipiently discussed todate, is of fundamental importance and significance. Lateritic gold can be classified texturally as: dusty and diffused, fine, thin platy, taDular, and nuggets. Such gold is pure, and is often restricted to nodular (pisoliths, ooliths, concretions) forms or the matrix, that constitute the crusts or lateritised gravel beds which have an essentially goetnitic nature. Further this gold is recovered directly by mining the crusts or the adjoining placers with the metal derived from them. The thickness and extension of laterite crust zones is extremely variable depending oh the paleoclimatic conditions, and is conditioned to the favourable lithology and its structural expression. However, the "growth" of gold in these laterites will be conductive , without doubt, to several small scale mining activities, specially in the developing countries and regions limited to latitudes 309N and 309S.

Jan 1, 1987

By Jorge Lanza

SUMMARY La Granja copper deposit, in terms of volume, is among the five largest deposits in the world and represents reserves of three thousand million tones. The field consists of a 40 m. thick layer of copper lying over the secondary ore and further down the primary copper. The flotation process has indicated a recovery rate of 88 to 90 percent and concentrates of 27 to 32 percent of copper. The acid leaching process of low grade ore produces financially acceptable results. To carry out the project, it is necessary to build long distance pipelines and a port. Both the Feasibility Study and the Environmental Impact Study on the project have been approved by the Peruvian government. INTRODUCTION La Granja is located in the district of Querecoto, province of Chota, in the department of Cajamarca, in the Northwest of the country (Figure 1). Geographically it is situated on the eastern slopes of the Andean mountains at an altitude of 2,000 to 2,700 m.a.s.1. (Figure 1). The site is an 8 hour car ride from the city of Chiclayo, capital of the department. The first 60 km. are over a paved road and the remaining distance is over a narrow hard dirt road. The copper porphyry of La Granja was discovered between 1969 to 1971 during some geochemical prospecting activities carried out by the State mining institution, Ingeomin (currently Ingemmet). From 1978 to 1982, Ingemmet continued with its geochemical and geophysical studies supported by a German technical assistance program. A total of 19 bore- holes were drilled (5,814 m.) and a 90 m. long tunnel made. This study calculated reserves of 175 million MT. In 1993, Minero Peru drew up a technical-financial study based on the above studies and proposed a 12 year extraction operating program: 20,000 MT daily using the leaching process, followed by 13 years of operation using the flotation process with the same daily volumes. In 1994, Cambior Inc. won an international auction in order to carry on further exploration work and to have a purchasing option. Since that date the company

Jan 1, 1998

By C. Alexander

Stillwater Mining Company is developing a second underground palladium and platinum mine approximately 21km (13 miles) west of their existing Nye operation in south central Montana. A 5650 meter (18,550-foot) tunnel is required to gain access to the ore bearing horizon (J-M Reef). Access and primary mine development can be accelerated through the use of two 4.6 meter (15-foot) diameter tunnelboring machines (TBM). One TBM was purchased new while the other was purchased used. Machine specifications, site support facilities, portal/launch chamber construction, TBM assembly, startup and operation are discussed in this paper.

Jan 1, 1999

By J. Yordan, J. Zinterer

Effective removal of ink particles by froth flotation is of up-most importance in paper recycling. In this study, the potential use of talc particles as carriers of difficult-to-float fine ink particles is investigated. In order to accomplish ink particles removal, the interactions between talc and oily- ink particles in aqueous solutions containing flotation chemicals was studied by zeta potential distribution measurements and with the impinging jet apparatus. The chemical conditions under which talc-ink adhesion occurs are identified and reported.

Jan 1, 2003

By Terry Quinlan

The financial evaluation of an orebody uses estimates for the grade of ore produced during each year for the life of the mine. Assay data from the Dolphin Scheelite Mine is used to estimate grades by the Polygonal, Ellipsoidal and Disjunctive Kriging Methods. The results are compared with simulated production data, to show the existence of a bias associated with each method. The affect of bias on the financial evaluation of a theoretical model ia assessed.

Jan 1, 1979