Search Documents

By Vas Choudhry, Randhir Sehgal

Conventional clean coal technologies which consist of coarse coal cleaning by gravity methods and treatment of natural fines by flotation can only remove a portion of the pyritic sulfur and ash in the coal. Higher (+90%) pyritic sulfur rejection is attainable when coals are ground to ultrafine sizes to enhance liberation of the mineral matter and then cleaned. However, cleaning of coal at very fine sizes poses a number of unsolved problems, the chief one being the loss of cleaning efficiency. This, of course, means that liberation of pyrites does not always equal its rejection. In addition, the dewatering of fine- cleaned coal, and its handling, transportation, and acceptability to the utility industry a1 so pose considerable technical and economic problems, especially when compared to the FGD alternative. This paper addresses some of the critical issues involved in the cleaning of ultrafine coal s.

Jan 1, 1989

By A. J. Friedrich

Conveyor belts are designed to go unnoticed. When they work well, they attract little attention. When they are not doing the job right, it is noticeable, and they need to be fixed immediately. Vulcanising contractors compete for the maintenance of belts in mining/quarrying and general materials handling worldwide. Damage repair is approached in similar fashion. The damaged section of belting is normally cut out and discarded, and the belt re-spliced using hot vulcanising, Cold splicing, or mechanical fasteners/clip joints. However, there is a cost-effective alternative, alleviating the need to remove damaged sections which are often perfectly recoverable. This is the use of cold-curing repair resins and adhesives.

Jan 1, 2000

By K. V. S. Sastry

Pelletization, sintering, and pressure compaction are the most common methods used to agglomerate ore concentrates. Over the last 20 years agglomeration has grown enormously in popularity and has become a standard unit operation in the nonferrous, cement, fertilizer, and ceramic industries. However, it is in the processing of iron ores and the preparation of blast furnace feed that agglomeration is used most and its application has grown fastest (Ball, et al., 1973; and Sastry, 1977). This chapter deals with an account of the current practices and future trends in the application of computers relative to an overview of the process design and engineering considerations of the unit operation of agglomeration.

Jan 1, 1979

By O. Fernandez, M. Vesely

Abrasive grinding, leading to ultrafine product and "critical size" material buildup inside the mill, is proposed as the cause of high power consumption and low capacity in many fully autogenous grinding processes. Addition of steel balls (hence, semiautogenous grinding) or pebble removal and separate crushing have been used, with different efficiencies, to overcome the problem. Information and data for the conceptual analysis, basic design, and operation of a pebble crusher at the Los Bronces semiautogenous grinding plant is presented along with data showing a production increase of 1000 t/d (1100 stpd) and significant operating costs savings.

Jan 1, 1987

By Malcolm J. McPherson

Mine shafts that are used as primary ventilation routes are different in their airflow characteristics to other subsurface openings because of the aerodynamic effects of guide rails, buntons, pipes, cables, ropes, and shape, size and velocity of conveyances. As many shafts contribute heavily to the overall resistance of a mine ventilation circuit, it is important to be able to predict the resistance of a planned shaft with reasonable accuracy. This paper describes part of a study on the ventilation characteristics of hoisting shafts, conducted for the Basalt (Nuclear) Waste Isolation Program (BWIP). Methods of quantifying each of the four components of shaft resistance are developed; namely the shaft walls, fittings (buntons, pipes, etc.), the skips or conveyances, including the dynamic effects of their motion, and shaft stations. Practical guidance is given on ways of reducing the shaft resistance. The paper concludes by giving a step by step procedure for the ventilation aspects involved in the design of combined hoisting/ventilation shafts.

Jan 1, 1987

By Gemei Yang, Pierre Mousset-Jones, Felipe Calizaya, Malcolm J. McPherson

Laboratory tests on controlled airflow recirculation have shown the development of transient states in response to changes in system prevailing conditions such as those generated by a sudden start-up and stoppage of fans. Researchers in many European countries have developed various models to explain these phenomena. However, these models failed to consider some important factors such as diffusion and dispersion of gas in turbulent flows. For both in-line and cross-cut recirculation, tests have shown that after the start- up of a booster fan, the gas concentration in the system fluctuates, reaching high levels at the initial states and slowly dying out with time. These fluctuations cannot be represented adequately by simple step-wise functions but rather by smooth, albeit complex equations. In this paper, the phenomena are explained by the convection-dispersion theory, and represented by a mathematical model. Based on a few simplifications and applying Fourier's Transform Method to the differential equations of the flow recirculation model, an integral form of gas concentration function was derived. The Simpson Integration Method was used to compute numerical results for two laboratory tests. The paper also discusses the range of the dispersion coefficient to improve the accuracy of the model.

Jan 1, 1989

By E. Topuz, M. J. McPherson, I. M. Konduri

The research is carried out to investigate the flow mechanics and effectiveness of face ventilation using induction fans, as an effort to provide a more efficient alternative to conventional auxiliary duct or brattice ventilation systems. The induction effects and plume longevity of fluid jets are being studied with the help of a plexi-glass model, using water as the fluid medium and creating a system that is dynamically similar to the flow in mine headings. This scaled model represents a typical 1.5m x 6m x 25m heading connecting to a crosscut. Reynolds Number criteria are used to obtain dynamic similarity of the flow in the designed model to simulate real mining conditions. The role of various parameters such as nozzle position in three dimensions, airway roughness, nozzle geometry, and flow rate in the jet are studied. During the laboratory tests, flow visualization techniques, coupled with still and video photography, were employed to identify the flow patterns. The results indicate that in typical coal mine headings, jet fans can produce effective face ventilation for distance up to 30 meters.

Jan 1, 1995

By J. Alton Burks, Roy C. Bartholomae

The chain conveyor is utilized extensively in underground mining to convey raw ore, especially coal. It is estimated that several thousand loading and continuous mining machines rely on this type of conveyance. Although the chain conveyor is both efficient and highly reliable, its use is generally associated with the production of noise levels that often exceed 105 dBA at the operator's position. Thus, it is one of the most significant contributors to the occupational noise problem experienced by miners in the underground coal mining environment. Conventional engineering noise controls that result in an average reduction of 4 dBA have been previously designed and implemented. However, a novel solution involving a change in conveyor operation has been proposed that takes advantage of two aspects of conveyor noise: 1) conveyor noise has an approximately cubic dependence on conveyor chain speed and 2) due to the damping provided by coal, a full conveyor is 5 dBA quieter than an empty one. An engineering analysis has shown that a significant reduction in the operating noise level of a typical continuous miner can be achieved through the use of an adjustable speed drive automatically controlled by a coal loading sensor that maintains a full conveyor at all times. The potential reduction depends primarily on the mining conditions (coal seam thickness and the presence of either rock or water) and varies from 7-18 dBA. Other benefits to be derived from the use of a variable speed drive include reductions in power consumption, dust, and maintenance costs.

Jan 1, 1992

By D. Constantinides

In 1981 a Zn-Ag-Pb deposit was discovered in the vicinity of Molai, Greece. Subsequently, it was determined to be of the Kuroko type. The geology of various areas in the southeast Peloponnesean Peninsula is similar to that of the Molai deposit. Since favorable geologic criteria are present, absent, or unknown in varying degrees in all areas, it was deemed necessary to classify and rank the prospective areas according to the level of information available. For each level of information, an ore discovery model based on pragmatic exploration criteria was developed, enabling the favorability of occurrence to be calculated for each area. A Monte Carlo simulation was used to calculate the probabilities, the input data consisting of quantitative and qualitative estimates of the geologic criteria for each area. Three levels of information were modeled : Level A consisted of 9 criteria, level B of 12 criteria, and level C of 20 criteria. The three levels of information were tested on the Molai area. The results exceeded expectations, showing the gen¬eral trends which control mineralization at the lowest level of information. With an increase in the level of information, geological trends become more evident and a differentiation can be made between areas containing Cu mineralization, exhibiting a low probability, and areas likely to contain Zn-Ag-Pb mineralization. The models were then applied to the neighboring areas - only level A and B were available.

Jan 1, 1986

By H. Lind

Mining in Estonian oil shale deposit mainly takes place in the Ordovician, Keila-Kukruse aquifer. The aquifer is affected by mining and is fully dried out around the working mine areas (Perens and Savitski, 2008). The groundwater level is decreased down to 30 m, to the mine floor elevation using about 30 pumping stations (Lind, 2005). The pumping rate is very high - depending on the season, ranging from 10 up to 40 m3 per ton of produced oil shale (Reinsalu et al., 2006). The Estonian oil Shale Company mined 15.5 million tons of oil shale in 2007 (Source: Estonian Oil Shale Company). In order to predict the effects, and avoid the social and environmental impacts, there is a need to continuously monitor the situation and run software simulations aiming at decreasing the pumping rate. This becomes even more important since the environmental taxes on usage of groundwater resources increase every year. Therefore, it is necessary to monitor groundwater level and quality, and develop a groundwater model for the overview of the situation during mine operations and also for a number of years after mine closure.

Jan 1, 2008

By K. G. Colman

Introduction This text is intended to provide the operator and turnkey contractor with the basic data for sizing vibrating screens to be used in ore crushing plants. The basic capacities, modifying factors, etc.. used in the area requirement calculations were developed empirically and modified to their present values based upon years of practical applications. It must be pointed out that screening is much more of an art than an exact science; however. the information presented here should provide for reasonably accurate screen sizing when applied to many metallic ores. Types of Screens There are two types of screens which can be used for strictly sizing applications. These are two- and four-bearing screens; both are inclined circle-throw machines. Two-Bearing Screens The motion of a two-bearing screen is generated by unbalanced weights attached to the vibrator shaft. The body of the machine is usually supported by steel coil springs (see Fig. 8). The main advantage

Jan 1, 1985

By Andrzej M. Wala

A prototype expert system for planning and designing an underground coal mine has been developed in a doctoral study at the University of Kentucky. This prototype expert system for underground coal mine planning and designing consists of a number of knowledge bases concerning different elements of design (e.g., ground control, excavation and bulk materials handling, ventilation, etc.). The objective of this paper is to present the development process of the ventilation design knowledge base for this prototype. This expert system prototype is intended for building an instructional expert system for underground coal mine design. Therefore, the undergraduate course on mine design has been used as the basis, for its development. Because of the availability of knowledge and expertise, this research study has been limited to development of a knowledge model for the Appalachian coal mining region.

Jan 1, 1993

By V. K. Karra

Research by various workers has shown compressive comminution to be significantly more efficient than impact comminution. Based on the work being done at Nordberg, wet compressive crushing in cone crushers producing finer and finer products, shows the feasibility for partial substitution of conventional tumbling mills. For further substitution, major challenges are processing of fine feed slurries in cone crushers to realize a significant size reduction of the particles, and understanding the limitation of the gyratory type units in terms of finest product achievable. The paper addresses the challenges involved, efforts at Nordberg, and the implications to conventional comminution flowsheets.

Jan 1, 1989

By G. D. Elliot, R. L. Grayson, G. L. Winn

For the years 1990 and 1991, West Virginia's underground coal small-mine fatality rate was approximately 10 times higher than the national coal-industry fatality rate. Although the number of fatalities went down from 22 in 1991 to 17 in 1992, West Virginia still led the nation in coal-mining fatalities. A team of mining and safety professionals from West Virginia, interfacing with the Mine Safety and Health Administration and the West Virginia Office of Miners' Health, Safety and Training, studied this problem. A clear path for formal intervention was determined and is presented here.

Jan 1, 1996

By Helen Joyce, Larry Twidwell, Jay McCloskey, Eric Dahlgren, Andy Hadden

The reduction of dissolved selenium oxyanions from mine wastewater utilizing an elemental iron cementation technology on been studied on a laboratory scale at Montana Tech of The University of Montana and on a pilot scale at MSE-Technology Applications as a water treatment process potentially capable of removing dissolved selenium to GO WL. Laboratory and pilot scale studies using elemental iron have demonstrated effective removal of dissolved selenium. Enhanced selenium reduction rates have been demonstrated when galvanically coupled iron/copper and iron/ nickel are utilized. The laboratory and pilot scale results are presented and discussed.

Jan 1, 2005

By Mark E. White, John H. McCowan, Michael C. Costello

Minproc Engineers has carried out the design construction and commissioning of thirty two process plants in the period 1978-87. Twenty eight are gold silver recovery plants, and of these twenty two were gold alone and six were gold and silver. In most plants carbon was used for gold adsorption. Desorption has been carried out using the USBM Homestake method, the Anglo American Research Laboratories method, and the Micron Methanol method. Electrowinning has utilised steel wool, stainless steel wool, and aluminium cathodes. Electrorefining using polished stainless steel cathodes is practised. This paper summarises the experience gained in these operations

Jan 1, 1987

By W. J. Wuest, M. J. DeMarco

The US Bureau of Mines (USBM) recently developed a rock-mass classification system for evaluating the structural competency of bedded roof strata. The system is called the coal-mine roof rating (CMRR), When compiled with the companion Lotus 1-2-3 spreadsheet, CMRR data are a useful tool with applications to longwall gate-road pillar design, safety-hazard mapping and artificial roof-support analysis. This paper gives a review of some applications under actual conditions found in current US mining operations.

Jan 1, 1997

By Dorothy A. Canter

Three Federal programs exist for identifying significant environmental chemicals, including minerals, that should be tested for toxicological effects. Two programs are mandated by law and can lead to industry-funded studies; they are administered by the Environmental Protection Agency and the Agency for Toxic Substances and Disease Registry, respectively. The third is the National Toxicology Program, a Federally-funded testing initiative. This paper summarizes the three programs, describes their similarities and differences, and discusses their applicability to minerals.

Jan 1, 1991

By James M. Johnson, David Landriault, Frank Palkovits

The term “Paste Technology” was first used in the late 1980’s. It was used to describe a high fines (15 wt% or greater minus 20 microns), low water content backfill material that could be transported underground through a borehole/pipeline distribution system (4” to 8” dia.) at a yield stress similar to fresh concrete (100 to 400 centipoise). This “Paste Backfill”, unlike slurry transported backfills does not segregate into separate solid and liquid phases at low pipeline transport velocities or upon disposal into the underground stope. Paste backfills can consist solely of fine material, or can include fines plus sand and aggregate similar to a concrete mix. Pipeline transport of paste requires that sufficient fine material (minus 20 micron content) is contained within the mix to lubricate the pipeline walls to create a plug flow condition. For concrete, the fine material is supplied through the cement addition to achieve high compressive strength. For paste, the fine material is generally available in large quantities in the form of mill tailings. The paste tailings can be transported underground for use as backfill or discharged on the surface in a tailings management facility (TMF). This natural abundance of fine grained material is not exclusive to mine tailings but is common to many waste streams in many different industries. This makes the disposal of many waste materials very amenable to paste pipeline transport and placement as a non-segregating slurry. The potential use of paste technology for a wider group of waste materials was realized by these authors and others over two decades ago. Through the effort of this small group the use of paste technology has expanded over the years to become recognized as a low cost, environmentally superior, and technologically controllable method of transporting and placing specific material waste streams with a low water content and high placement density. The high yield stress nature of a paste also lends itself well to the blending of one or more coarse waste materials into the fine waste material paste stream. This allows all the waste materials to be transported by pipeline, increases their placement density; decreases the supernatant release/treatment, reduces contaminant mobilization, hydraulic conductivity and oxygen/water reactivity through encapsulation in the paste matrix. The following paper describes the present state-of-the-art use of paste technology in the world today. It also describes future uses of the technology that are under development and speculates on the overall use of the technology for waste management in the future.

Jan 1, 2005

By John L. Bolles

The mineral processing engineer must have some knowledge of mineral identification, and the greater his knowledge in this field, the greater will be his potential to do his own specialty well. Most metal-bearing ores and industrial minerals require processing of some kind to produce a salable product or a material suitable for further processing. The types of treatment are many, but each one is aimed at separating a mineral or family of minerals from others. Obviously, then, it is basic to all mineral processing to identify the minerals present in the raw material and in intermediate and final products resulting from processing. Very often the mineral processing engineer will enter planning while exploration of a mineral prospect is going on. He will examine hand specimens, drill cores and cuttings, bulk samples, and materials in place. He must identify the valuable minerals, their occurrence and associations with other minerals, and the identity of diluents or host rock. An exact and detailed knowledge of the raw material will usually suggest the treatment processes that should be investigated in the development of the most suitable scheme for that particular raw material in that particular location. Physical properties of a mineral often lead directly to a process for separating that mineral from others. Some well-known examples of these are: magnetic separations for such minerals as magnetite, rutile, ilmenite; gravity separations for gold, silver, galena. cassiterite; flotation separation for most sulfides; distillation of mercury from cinnabar; and selective dissolution in specific solvents such as halite or sylvite in water, gold and silver in cyanide solutions, copper oxides, carbonates, sulfates and silicates in dilute sulfuric acid. These processes and many others are described in detail elsewhere in the Hand¬book and so it is not appropriate to give details here, except to emphasize that processing is aided greatly by complete mineral identi¬fication. Developing a treatment scheme for a new mineral discovery is an exciting assignment fag the mineral processing engineer, but much more of the usual work relates to quality control in existing plants. Here too, mineral identification is important. Some processing is aimed toward producing an end product which will meet exacting specifica¬tions regarding purity or allowable diluents. In this situation it is vital that contaminants be identified so that the process can be adjusted

Jan 1, 1985