Search Documents

By Thomas B. Borak, Keith J. Schiager, Janet A. Johnson

INTRODUCTION Several major factors introduce uncertainties into the assessment of radon progeny exposure to miners using time-weighted average radon progeny concentrations: uncertainty in the measurement of radon progeny concentrations in specific areas, assignment of an individual miner's time to those areas, variation in radon progeny concentration between measurements and potential human errors involved in calculating concentrations and handling data. The currently available grab-sampling methods for determining working level were analyzed to determine the magnitude of the uncertainty due to each of these factors. For all measurement methods studied, the variation in the airborne concentration with time in operational areas of a mine is the dominant factor in the uncertainty in determining annual radon progeny exposures for individual miners. Uncertainties relating to accuracy of the method and precision of measurement were found to contribute a significantly greater portion of the total uncertainty than human errors. Under normal conditions, if the technicians performing the measurements are conscientious and well trained, human error contributes little to the total uncertainty of the radon progeny exposure determination. The primary goal of radiation monitoring is the reduction of radiation exposure to the lowest reasonably achievable level below regulatory limits. Monitoring personnel in mines should be trained not only to obtain accurate estimates of miner radiation exposures but also to recognize and, when possible, to implement correction of situations which result in unnecessarily high radon progeny exposures. ESTIMATION OF UNCERTAINTY DUE TO HUMAN ERRORS Human errors affecting the assignment of annual radon progeny exposure to individual miners can be placed in two categories: those related to the measurement of radon progeny concentration in specific mine areas and those related to estimation of occupancy time for individual miners and transcribing data to permanent records. The former are specific for the measurement method used; the latter are common to all methods. Errors in Determination of Working Level All systems for determining radon progeny concentration require measurement of several parameters, which include volume of air sampled, count rate and decay time. These quantities and appropriate constants are used in a basic equation, specific to the system, which estimates working level. An unintentional random mistake in measurement of any one of these parameters or in the selection of proper constants will contribute to the uncertainty in the determination of working level. In our analysis of human error we separated each measurement method into a sequence of independent operations, with each step subject to operator error. For each operation we estimated the probability of occurrence and the consequence of errors to obtain a resulting uncertainty. Certain types of errors result in specific consequences. For example, we assumed that an error of 5 seconds in timing of a 5-minute sample results in a fractional error of 1/60 (1.7%). Other types of errors can result in a range of uncertainty. Transposing digits read from a scaler can produce errors ranging from near zero to approximately 60%. In these cases we calculated the statistical variance for the distribution of errors. We assigned the square root of the variance divided by the mean as the consequence factor for that type of error. This is essentially the same as a coefficient of variation. The product of the probability of occurrence and the consequence factor is the fractional uncertainty in the measurement due to that particular error. The total uncertainty due to human errors is calculated by taking the square root of the sum of the squares of the uncertainties generated by all manual operations. Uncertainties Due to Human Error for the Kusnetz Method One of the techniques most commonly used to estimate working level in U.S. uranium mines is the Kusnetz method. A generalized way to express the equation used to compute WL by this method is: WL = (Net Alpha Counts)/(V)(ST)(CT)(E)(K) where: V = sample flow rate in liters/min ST = sampling time in min CT = counting time in minutes E = absolute counting efficiency K = Kusnetz conversion factor (dis/min-L per WL), as a function of decay time in minutes. The example of human error analysis presented here is based on the Kusnetz procedure having a timing sequence of 5 minutes sampling time, 40 minute decay time, 2 minute counting time. During the sampling procedure a stop watch is used to determine the timing interval. We assume that it is common to make small timing errors of a few seconds, but larger timing errors occur infrequently. Errors greater than 30 seconds are considered to be essentially non-existent since we assume that the

Jan 1, 1981

By D. A. Norrgran

The recent development of rare earth permanent magnets has revolutionized the field of magnetic separation. The advent of rare earth permanent magnets in the 1980's provided a magnetic energy product an order of magnitude greater than that of conventional ferrite magnets. This has allowed the design of high-intensity magnetic circuits operating energy free and surpassing the strength and effectiveness of electromagnets. New applications and design concepts focused on the mineral and metal processing industries have evolved. This technology also led to the development of various magnetic separators specifically designed for mineral processing applications. Applications which were not previously considered are now being applied to primary mineral upgrading and recycling and secondary recovery.

Jan 1, 1993

By Ratnakar Singh, Raj Kishore, Kisor Kumar Sahu, Ranjeet Kumar Singh, Ganesh Chalavadi

The Falcon concentrator is capable of separating minerals in fine size classes based on their differential density. Separation of mineral particles depends upon the fluid flow characteristics and relative movement of particles in a fluid. In the present study, a fluid flow characteristic inside the Falcon concentrator was established through experimentation and modeling. The Falcon concentrator has two fluid entry points: (a) Fluid entering through gravity assisted feeding system and (b) Fluid entering through the fluidized hole on the concentrator wall. In order to identify the role of fluid entering the concentrator, a tracer was injected into the system. As per the tracer based experimentation, it was established that fluid entering through the gravity based feeding system is responsible for thin flowing film formation in the stratification zone where particles are stratified based on their relative density. The momentum balance and continuity equations were simplified for a high centrifugal force field, and the fluid velocity profile was estimated inside the thin flowing film. Estimated fluid flow profiles will help to simulate the particle trajectories inside the Falcon concentrator. The influence of rotational speed, fluid flow rate, and cone angle on the fluid velocity profile were investigated. Fluid thickness over the concentrator wall is also estimated, and it is typically of the order of ~150–200 μm.

By Boris K. Krstev

INTRODUCTION The flotation process, in the real industrial complexes, is characterized by the existence of the significant number of the close reciprocal interrelationship between the input and output Darameters. Traditional complexity is appeared with regard to absence of the suitable a priori information for the physico-chemical characteristics of the flotation process. It’s led to needful of taking of consideration about the undefinition which have got the place in the real conditions and application of the statistical methods. The identification of the flotation process through statistical methods is conception of the more-stages procedure, including the collection and previous analysis, the choice of the model structure and valuation method, the estimation of the model un- known parameters and the results interpretation. The essential concept for the subject of this paper belongs to the empirical models ("black-box") and deals with optimizing in constant industrial plant process. The offered method envisages the application of process operation data in order to improve the work process or constant accomplishment of better results for the target function in relation to the former achievement. The optimum process solution isn't afixed value under the influence of various factors, but "a moving point" along the response surface and deviates from the scheme solutions. The evolutive planning method constantly "investigates and approaches" the optimum solution for the selected target function. As a matter of fact the expert operates the plant without interrupting the normal work process. The essential concept of method is to attain changes in the standard conditions, but so limited that they will not effect either production or the product. This method is based on statistical concepts and availability of following the risk of error. The possible influental factors for the flotation process (m=l, 2, 3) is following: the metal content in the feed ore; production level (t/h); grinding fineness in the flotation pulp; pH-values; the consumption of collectors and modifiers The possible target functions are: the recovery of plant capacity, metal recovery in the concentration process and concentration quality. The application of the evolutive operativity method in the chalcopyrite flotation- Bucim concentrator, combines the statistical data and the operator's experience in the interpretation and making a decision which adds up to the precise automatic performance of the process. The advantages of this method in relation to the existing procedure for the flotation process are the following: • The method is unexpensive and losses are reduced to the time necessary to collect the data and record them in the computer. This method provides a constant process control and a quality decision which is better than those brought by an ex- pert with great experience ("hit-and-miss method"). • The method also provides incidental data about the effects. • The method should not be considered as a procedure for solving an incidental problem ("crash program"). • The obtained results must be interpreted by an appropriate expert in order to be considered instructive. MATHEMATICAL STATISTICS Taking into consideration the complexity of the enrichment processes it's necessary the application of "black-box" and mathematical modelling. The presence of the indefinite elements compel us towards the both theory of the probability and mathematical statistics. The mathematical statistics by the mineral processing investigation of the valuable raw materials in the last years has had greater signifance and widely spread application. The application of the mathematical statistics methods for the technological pro- cess analysis and the construction of the mathematical models is bound up by the task putting of the automatic control system de- sign (Fisher R. A. 1941, 1949). The statistical analysis in the enrichment processes is applied formerly, especially in the sampling estimation. Contemporary, in the last years is imposed the tendency of mathematical statistics application for the obtaining of quantity characteristics and quantity valuation from the individual influental factors. Above mentioned tendency in the significant level is based by the mathematical statistics development as a mathematical discipline close connected with the technical cybernetics general joining to the investigated object as a "black-box". Another essential factor in the mathematical statistics development is appeared the created mathematical theory of experiments as a new, to some extent, autonomous statistical domain. The theory of experiments has demonstrated exclusively importance for the investigation of the complex more-factorial processes in the chemistry, mineral processing, metallurgy etc. The investigation by the enrichment processes of the valuable raw materials and their management is possible by the statistical method application. In the same time, it's possible to use the wide-spread traditional methods of the statistical analysis, such as the methods of the dispersion, correlation, regression etc. Also, it may be mentioned above all the methods of the statistical planning of the extreme experiments. The more perspective are representatived some cybernetic methods which are based by the probability as an approach in the process analysis, for example, the identify of the ways and forms, the graph application as an additional instrument in the correlation analysis, the dynamic programming etc. The mathematical statistics application in the laboratory investigation scale is connected above all by the experimented material analysis and the compact representation of the obtained results. The mathematical statistics methods are more varrying and may be applied in the investigations of the wide circle of problems

Jan 1, 1996

By Yukika Miyashita, Takahiro Inoue, Kenji Namikawa, Masashi Matsumoto, Junichi Koseki, Yoshihiro Terashima

"In order to construct an underground two-layer expressway branch junction structure with a height of 14.7 m and a width of 22.3 m, two shield tunnels in each layer were combined by using a non-cut-and-cover enlargement method in sedimentary soft rock. Before and during the construction work, preliminary analysis, in-situ investigations and laboratory tests were conducted to ensure the construction safety and to evaluate the deformation characteristics of sedimentary soft rock. The construction project was safely executed without any water leakage or collapse of tunnel working face. The predicted results from preliminary analysis were almost similar to the measured values. From the detailed investigation of measured results, it was confirmed that the deformation characteristic of the sedimentary soft rock was observed to a small extent as the ground deformation derived from construction work. INTRODUCTION In recent years, some newly constructed urban expressways in Japan are being planned as underground structures due to the consideration of roadside environment. The construction of such underground expressways is frequently conducted using a shield tunneling, a typical one of non-cut-and-cover methods, to prevent any adverse effect to traffic in arterial roads, operation of nearby commercial establishments, and daily lives of local residents during construction work. For underground urban expressway, the connections with existing road network on ground surface or on elevated sections are indispensable, which require the construction of an underground branch junction with large cross-section. This raises a technical difficulty regardless of the open-cut or non-open-cut construction method."

Jan 1, 2016

By Bernard F. Anderson

INTRODUCTION In this chapter, the term "down-the-hole drill" (DTH drill) is used as a generic name that encompasses the various trade names and other references such as "downhole drill," "in-the-hole drill," etc. This chapter is limited to a description of DTH drills used in stoping large underground ore bodies. DTH drills differ from conventional drills by virtue of the placement of the drill in the drill string. The DTH drill follows immediately behind the bit into the hole, rather than remaining on the feed as with ordinary drifters. Thus, no energy is dissipated through the steel or couplings, and the penetration rate is nearly constant, regardless of the depth of the hole. Since the drill must operate on compressed air and tolerates only small amounts of water, cuttings are flushed either by air with water-mist injection or by standard mine air with a dust collector at the collar. HISTORICAL DEVELOPMENT Mine managers have long known the economies enjoyed by quarry and open-pit operators in producing large quantities of ore. The savings are due primarily to the availability of massive equipment, capable of drilling large blastholes to reduce the amount of drilling, increase the fragmentation, reduce secondary blasting, and im¬prove the flow of the product. In an attempt to reduce underground mining costs, various methods are used for long-hole drilling, includ¬ing standard pneumatic percussion drifters and diamond drills. These systems have their shortcomings; percus¬sion drills are limited to small hole sizes and they ex¬perience excessive deviation and significant loss of energy with increased depth. The diamond drills provide deeper and straighter holes, but only at high cost. Both systems suffer from high noise levels, low penetration rates, and poor explosives distribution, among other problems. When the mining companies approached the drill manufacturers for a compact and portable large-hole jumbo for underground use, they specified not more than 1 % deviation on 60 m (200 ft) of vertical hole and a penetration rate of 15 m/h (50 fph). On Dec. 23, 1960, a test unit was placed in service in Montana and met the performance criteria. Though lacking the so¬phisticated features available today, the economies of surface blasting were brought underground. Unfortunately, the first system did not gain immedi¬ate acceptance in the industry. Among the factors con¬tributing to its demise were resistance to change, the need to alter development methods for the ore bodies, and a lack of flexibility in moving the rig from setup to setup and from level to level. In 1972, the mining industry again challenged the drill manufacturers to provide a workable jumbo that would combine compactness, ease of maintenance, relia¬bility, and efficiency, all on a self-propelled chassis. The manufacturers responded by providing improved jumbos, which have been accepted with enthusiasm throughout the mining industry. Today's DTH jumbos are capable of drilling from 100 to 200 mm (4 to 8 in.) diam holes that can be reamed to even larger diameters. The holes can be drilled to depths of 150 m (500 ft), depending upon ground conditions and the capability of the jumbo to retrieve the steel and drill. Fig. 1 illustrates a typical DTH jumbo. APPLICATIONS The uses to which DTH drill jumbos have been put are quite numerous, with new uses being found regularly. For convenience, these uses may be classified as primary blastholes and nonblasting holes. Primary Blastholes The original purpose for the development of the DTH jumbo was for drilling primary blastholes that could be mined by open-stope methods. Prior to the advent of the DTH jumbo, extensive development was required before production drilling could begin. Sub¬levels were required to allow access for column-and-arm stopers or ring/fan jumbos, to the extent necessary based on the effective penetration of the chosen machine. With the DTH jumbo, the mine engineer is able to reduce preproduction time and development costs. How¬ever, the most significant saving results from an im¬proved cost per ton of broken ore in the production phase. To utilize a DTH system, only a top heading and drawpoints are necessary. The top heading can be the width of the ore body with a 3.7-m (12-ft) back. A drop-raise pattern is drilled and shot to begin the stoping operation, providing a free face for subsequent blasting. A typical layout is illustrated in Fig. 2. The advantages of this system include: 1) Drilling and blasting are independent operations, and blasting can be performed at a rate congruous with the mine's ton-per-day capacity. 2) The development layout is simplified. 3) Good explosive distribution is achieved, provid¬ing more uniform fragmentation. 4) Environmental conditions for operators are im¬proved, including improved safety with all work directed downward (not overhead), lower noise levels, little fog, and a reduced dust count. 5) Improved production per manshift. 6) Simplified and easier operator work cycles. 7) Reduced cost per ton of product. 8) Fewer holes lost due to ground shifts. Nonblasting Holes With the introduction of the compact DTH jumbos, other practical uses became apparent, including the drilling of: 1) Holes for sand fill, from level to level and from level to stope. 2) Drain and dewatering holes. 3) Power and communications cable holes.

Jan 1, 1982

By Victor E. Archer

INTRODUCTION Man is exposed to many agents which induce mutations in germ cells and/or cancer at work, at play, and at home. In this total mix of mutagenic and carcinogenic agents, how important are radon and its daughters? Before man moved into caves and other permanent dwellings, the principal mutagenic and carcinogenic agent to which he was exposed was natural background radiation--cosmic rays, radium and potassium-40 in his food, plus gamma rays and radon from the soil and rocks. When man moved into caves, captured fire, and began to preserve and store foods, his exposure to carcinogens and mutagens took a quantum leap. Carcinogens and mutagens appear to act in the same way, that is, by altering the DNA or nuclear proteins of cells. Most mutagens are carcinogens, and vice versa, so when I say mutagens from here on, I will be referring to both. The relationship of the two is emphasized by the fact that administration of a carcinogen to a group of animals not only increases cancer rates among the exposed animals, but also among their progeny (Tomatis 1979). Environmental Mutagens Smoke from man's fires, overheated foods, and foods preserved by smoking, resulted in ingestion and inhalation of many polycyclic aromatic hydrocarbons--many of which are mutagens. Caves and houses with tight windows and doors tend to collect the radon which is constantly emanating out of soil, rocks and concrete, so man's exposure to the radon daughter component of background radiation increased several fold. Preserving food by salting or pickling with material that contained nitrites and nitrates led to increased ingestion of nitrosamines, which are potent mutagens. When his grains and other foods were stored in slightly damp rooms, fungi or mold would grow on them. Several of these fungi are now known to produce very potent mutagens. The best known of these is aflatoxin B (Ramachandra 1979). It may seem strange that a living organism would produce a mutagen. One might think that it would scramble its own genetic heritage. The reason it does not is that it produces the mutagen in an inactive form. It can be activated only by an animal's enzyme systems after being eaten. When man moved into cities, the collective smoke from wood and coal fires further increased his exposure. That particular smoke has now mostly disappeared, but has been replaced by smoke from automobiles and industry. When man moved into the age of technology, his exposure to mutagens again increased dramatically. Many mutagenic chemicals, from benzene and beta naphthylamine to a long array of pesticides and tobacco products have been added to our environment. Excess deaths from cancer are now being observed among chemists in most industrialized nations. Mutagens are even found in much of our wine, beer, and whiskey (Keller 1980). Some of the chemical mutagens were widely used in food or in other commercial products before their potential was discovered. Striking examples of this is the original butter coloring agent and the polychlorinated biphenyls that have been widely used in brake fluids and electrical transformers. Large quantities of them have been discarded or disposed of in a careless manner--in such a way that many of them have contaminated our food, our ground water and air (Landrigan 1981). In this nation, with the help of several recent laws, we were just beginning to get control of the industrial chemical mutagens. With the relaxing of these laws that is currently going on, it appears that it will be many more years before we really bring chemical mutagens under control. Many nations have yet to come to grips with this problem. On top of this massive array of chemical mutagens we have now added radiation from many artificial sources. For most of us this means medical X-ray and fallout from nuclear weapons testing. Ionizing radiation is one of the most potent mutagens, so it has caught the public eye, and its contribution cannot be ignored. Fortunately, by the time we started using radioactive materials in quantity with the Manhattan Project, we had experience with radium and X-ray (some of it bad); we knew enough radiobiology and enough about methods of radiation protection so that most nuclear laboratories have had a phenomenal record of radiation safety. Radiation is one new technology with great potential for harm that has not exhibited that potential except for a few isolated situations like that of radium dial painters, uranium miners and atomic bomb victims. Uranium miners slipped into this list almost by accident. We could have protected our uranium miners just as well as we did the workers in nuclear laboratories; but we failed to do so. Why didn't we? The reason is simple. The Atomic Energy Commission was charged with protecting the health of their workers. They did not wait for a pile of bodies before they introduced controls. Congress appropriated the money, and taxpayers were willing to pay for the protection against radiation. Miners unfortunately did not work for the Atomic Energy Commission. Although mine operators were ignorant about radiation, the key item was that in the 1950s nobody was willing to pay the extra costs of adequate ventilation to control the high levels of radon and radon daughters in uranium mines. Control was not achieved until new laws and regulations were passed which made it compulsory. BIRTH DEFECTS AND CANCER

Jan 1, 1981

By M. F. Vancas

The advantages of using vertical pulsed columns as replacements for conventional mixer/settlers in the uranium industry have been known for some time. The advantages of the columns offer include a reduction in real estate for the plant, elimination of diluent evaporation and crud formation. This paper presents the findings of laboratory tests of pulsed columns extracting copper from pregnant leach solutions and also discusses potential advantages of the pulse column in copper solvent extraction.

Jan 1, 1999

By Yi Luo

A massive roof fall occurred in a small room-and-pillar coal mine. The roof falls occurred under a barrier pillar in a closed coal mine located a short distance above the active mine. The extensive fractures connected the active mine with the old mine, turning them into a “combined mine.” Since completely sealing off the roof fall area is prohibitively expensive for the mine, ventilating the connected old mine became the only option. A comprehensive investigation was conducted to understand the atmospheric condition in the old mine and to find an efficient way to ventilate the “combined mine.” A set of studies involving geology, gas content, pillar stability and mine subsidence were performed to explore whether the closed mine is filled with an explosive air-methane mixture. The air quantity measurement data were used to determine the resistance of the air path formed through the fractured zone. Observations and measurements made from a tour to the underground and mine surface enabled the formulation of simple but effective ways to ventilate the old mine. The ventilation network analysis also suggested methods of control, so that sufficient ventilation air can be directed to the two parts of the old mine.

Jan 1, 2010

By P. Somasundaran, D. R. Nagaraj, Tarun Bhambani, P. Patra

Flotation separation and recovery of value minerals from ores containing fibrous silicate minerals are known to be quite challenging. Earlier studies have established that the metallurgical challenges (poor selectivity and recovery, high energy consumption, etc.) arise from the impact of the fibrous minerals (with high aspect ratio) on pulp rheology, which was found be rather complex. The complex rheological behavior of ore suspensions containing particles with high aspect ratio and its influence on flotation outcome are investigated in this study. Flotation tests and rheological measurements were carried out with both ores (containing fibrous minerals) and a model system comprising nylon fibers (chemically inert) added to a copper ore that had no fibrous mineral. These studies allowed the determination of contributions of physical properties of the fiber to pulp rheological behavior. Optical microscopy images of the fiber pulp indicated that the fibers entangled to form two levels of microstructures: two-dimensional (2D) aggregates under semi-dilute (< 20% solids) conditions and three-dimensional (3D) microstructures at concentrations > 30% solids. The yield stress (σ) values determined for the fiber pulp were logarithmically related to the volume fraction of the 2D/3D structures. The relationships developed here for different ARs showed that the yield stress of a flotation pulp changes with respect to shape, size, and the concentrations of the microstructures. Implications to the effects of such entangle networks on selectivity of flotation separation are discussed.

By James R. Miller

This paper will describe the balling disc operation of the Marcona Mining Company at San Nicolas, Peru, with special reference to green ball quality. The report covers experience during the period of September and October 1965 and will be, more a state-of-the-art at Marcona report rather than -a technical treatise.

Jan 1, 1966

By C. L. Jiang

The selective depression of pyrite obtained from Kentucky No.9 seam in coal flotation with various kinds of inorganic and organic chemicals was systematically examined. Most of the organic chemicals tested showed little selectivity in pyrite depression. It was found that both orthophosphate and pyrophosphate were effective for the selective depression of coal pyrite in coal flotation using fuel oil as a collector. At substantially low concentrations of pyrophosphate, the flotation of coal pyrite was completely depressed over a wide pH range, while the coal flotation remained unaffected. The mechanism of the selective depression of pyrite by phosphates has been explained with the help of thermodynamic calculations of iron-phosphate-water systems and zeta potential measurements. It was shown that pyrophosphate reacts strongly with iron ions of pyrite to form stable hydrophilic iron pyrophosphate complexes on pyrite surfaces.

Jan 1, 1998

By R. R. Klimpel

In three recent publications, Klimpel et al (1988) and Klimpel and Hansen (1988, 89), the theory and invention process behind the identification of two new classes of sulfide mineral collectors were summarized. These two new families can be represented by the 111 generalized formulate: R1-S-R1 -NRI III (denoted as the F-series chelation family) and R-S-R or R -CHSCH-R (denoted as the S-series redox family). The influence of systematic changes in the various R groupings on laboratory batch flotation cell tests has been covered in the above references and will not be repeated in this paper. In particular, the recent article by Klimpel and Hansen (1989) should be studied as a research introduction to this paper.

Jan 1, 1989

By J. C. Emerick

Preliminary investigations have shown that wetland-based treatment systems can be an effective and relatively inexpensive control strategy for mine drainage pollution in eastern coal mining regions. This strategy also has potential for western mining regions, although too few systems have been installed in the west to permit general evaluation of the concept for western climates. The construction of prototype systems is encouraged for some situations. Wet-land environments have the capability of removing metals by natural geochemical and biological processes, including precipitation, filtration, ion absorption, and biological uptake and accumulation. Data presented for natural wetlands receiving mine drainage show removal of iron and other metals, and high accumulation of metals in soils and plants.

Jan 1, 1988

By C. Cho

One problem with the application of neural networks to the multivariable control of mineral and extractive processing is deciding whether and how best to use them. The objective was to compare neural network control to more conventional strategies and find any advantages in terms of set point tracking, rise time, settling time, disturbance rejection, and other criteria. The procedure was to develop neural network controllers using both historic plant data and simulation models. We tried various neural network control patterns including both inverse and direct neural network plant models. These were compared to state space controllers that were, by nature, linear. For grinding and leaching circuits, a nonlinear neural network-based model predictive control strategy was superior to a state space-based linear quadratic Gaussian controller. We also learned the importance of incorporating state space into neural networks by making them recurrent--feeding certain output state variables into input nodes in the neural network. We concluded that neural network controllers can have better disturbance rejection, set point tracking, rise time, settling time, lower set point overshoot, and can be more foolproof and easy to implement in complex, multivariable plants.

Jan 1, 1996

Because the Environmental Protection Agency has identified methane as a greenhouse gas, the importance of de gasification through gob wells has become more critical. It has been observed that the degree of methane emission is closely related to the geomechanical characteristics of coal bearing strata, roof, floor, and surrounding coal seams. Monthly production data from 250 gob wells were collected from the Warrior Basin in Alabama, and many interesting correlations were observed between methane production with longwall face width, face advancement rate, number of gob wells in a panel, and geologic columns. Extensive finite element analyses were performed to estimate the characteristics of the emission zone in an attempt to corroborate these findings. This paper describes an investigation for developing correlations between the geomechanical behavior of the methane emission zone with methane production.

Jan 1, 1996

Sphalerite is commonly floated in an alkaline environment and under such conditions the overall activation mechanism is obscured by the hydrolysis of Cu2+ and precipitation of Cu(OH)2. Electrokinetic and kinetic flotation tests show that the activation of sphalerite is a two-stage process; the activation products formed on the surface of sphalerite in near neutral and in alkaline solutions in the first rapid activation stage are "flotation-inactive". These layers, when formed in an alkaline solution, are unstable and are transformed into the "flotation-active" form in the second stage. However, the surface layers formed during activation in alkaline environment by copper in the presence of lead ions are very stable and even after a long conditioning time the flotation rate is not improved. Consequently, while both Cu2+ and Pb2+ activate sphalerite flotation, quite unpredictable effects may result when both are present in the solution.

Jan 1, 1997

By G. Xu, A. R. Kumar, N. A. Amoah

Prolonged exposure to high concentrations of respirable coal mine dust causes coal workers’ pneumoconiosis and silicosis. Underground coal mine roof bolter operators are more prone to elevated exposure to coal and silica dust. The canopy air curtain (CAC) was developed by NIOSH to protect roof bolter operators from the exposure. The CAC supplies filtered air over the breathing zone of the operator. This dilutes the high coal dust concentrations and provides for an impenetrable air curtain. Many studies have been carried out to improve CAC efficiency. However, field test has shown variable dust control efficiencies indicating rooms to further improve due to the nonuniform airflow distribution across the plenum and ineffective perimeter flow. This study therefore redesigns the CAC with optimized flow distribution that effectively protects roof bolters from coal dust exposures. Computational fluid dynamics (CFD) simulations are used to optimize the uniformity of airflow distribution across the plenum to achieve the best possible uniformity. A lab experiment validates the CFD model and confirms the ability of this design to reduce floor dust pickup, prevent external wind infiltration, and offer an improved protection efficiency

Mar 2, 2022

By Denys B. Smith

Electric logs and cuttings records from Zechstein 3 and 4 strata in boreholes in the British Sector of have been interpreted in the light of numerous cored boreholes through this sequence in north-east England. This interpretation shows that potash salts in the two cycles are thickest and most consistent in a belt 20 to 40 km wide parallel with and a few kilometres from the present basin margin, and are here generally similar in grade to those known onshore. The potash ores in both cycles are mainly of sylvinite in onshore areas, the layered Upper the Southern North Sea Potash of the fourth cycle being rather less variable but generally of appreciably lower average grade than the Boulby Potash of the third cycle. Potash salts in both cycles are highly variable in thickness and grade in basin centre areas where they have been grossly affected by diapirism of the thick second cycle salts.

Jan 1, 1978

By X. Cheng

The mechanism of cathodic decomposition of pyrrhotite was studied in deoxygenated solutions at natural, near neutral pH using potential and cyclic voltammetric measurements. Reaction products on pyrrhotite surfaces were examined by AES and XPS, and by analyzing the voltammograms for the electron balance of the reactions. Surface properties of the pyrrhotite/solution interface were characterized using ac impedance technique. The parameters of an equivalent circuit were determined by the nonlinear least squares fit (NLLSF) technique. The effect of cathodic polarization on floatability was investigated by micro-flotation tests. Possible implications to the flotation separation of chalcopyrite-pyrrhotite ores are discussed.

Jan 1, 1993