Search Documents

By Xinyang Xu, Jirun Xu, Changlie Deng, Kang Yan, Luo Qian

Cake filtration is a complex process and the cake constructure is very difficult to describe in theory. Cake constructure parameters, such as the cake prosity, pore size shape and even its distribution, are main factors influencing the filtration results but have not been thoroughly understood yet. In this paper the fractal theory, an effective mathematical method in describing the self-similar phenomenon is used to investigate the filter cake constructure, and the scanning electron microscope and automatic image analyzer are used to measure the cake constructure. Cakes which formed in different condition are examined and the fractal dimension of the cake are calculated. The study shows that the constructure of the filter cake can be approximated by Sierpinski fractal geometry and that the fractal dimension of filter cake, related to the particle characteristics, slurry concentration and filtration pressure is a good parameter to describe the pore size distribution and the cake penetrability.

Jan 1, 1995

By L. W. Saperstein, MJ. Carlson

With the goal of improving the strength characteristics of pneumatically emplaced material used for localized subsidence control, the binding additives fly ash, bentonite, and portland cement were examined for their effect on the support capabilities of coal refuse. It was found that, within certain concentration ranges, all three offered some increase in the ultimate strength of the backfilling mixture. However, portland cement gave the greatest percentage increases. Selection of the appropriate backfilling mixture will allow for the most economical and efficient subsidence control when pneumatic stowing is employed.

Jan 1, 1990

By T. Tamagawa, I. Iwasaki, N. X. Fu, M. Kobayashi

A low-temperature-chlorination selective oxidation followed by aqueous chloride leaching and SX-EW for producing electrolytic copper, elemental sulfur and ferric oxide was investigated for hydrometallurgical processing of a chalcopyrite concentrate. In this article, the selective oxidation phase of the process is described. The selective oxidation requires a temperature well above the CuCl-FeCl3 eutectic points. The test procedure was developed with a batch reactor and then tested with a continuous reactor. The process was initiated by adding small amounts of chlorinated samples to a fluidizing bed of dead-roasted sulfide concentrate micropellets. The selectively oxidized samples thus prepared were shown to fully dissolve copper, while virtually all the iron remained undissolved.

Jan 1, 2000

By J. R. Sturgul

Computer simulation models of working mines can be a great benefit to mining engineers. Such models have been used in mine planning (how many trucks-shovels to have, when to add new equipment, etc.) and mine design (should a dispatch system be purchased, where is the optimum location, for mine equipment, etc.). A simulation model can be thought of as a dynamic representation of the mine. It can be easily changed to reflect a variety of situations. A major problem for the engineer is how to present the results of the simulation study. This has now been overcome by means of animation to present the results of the simulation. The main simulation languages in use for discrete system simulation are SLAM, SIMAN and GPSS/H. Each has animation with SLAMSYSTEM for SLAM, CINEMA for SIMAN and PROOF for GPSS/H. Animation with SLAM and CINEMA have been on the market for several years whereas PROOF is a relative newcomer and has features not found in other animation software. This discussion will be confined to PROOF. Some of the comments will apply to all simulation and animation software.

Jan 1, 1995

By L. G. Austin

The use of crushed power station slags, both natural and coated, as granules for roof shingles shows some promise. Test shingles weathered for some years showed rust spotting and granule deterioration as serious problems. Chemical analysis on a particle-by-particle basis using a scanning electron microscope-energy dispersive spectroscopy system showed the wide variability of chemical composition of the granules within a given sample. Analysis of particles acting as sources of spotting within the weathered samples showed high iron contents but no rules could he developed for predicting the long-term stability of different compositions.

Jan 1, 1990

By N. L. Weiss

General The crushing of run-of-mine hard rock ores is the province of jaws and gyratory primary crushers described in the two preceding chapters of this section. While it is now seldom difficult to make a choice between the two to suit a specific set of circumstances, the governing factors merit a review, and that is the purpose of this chapter. For every size of feed there is a crusher of either type that can handle it, and it is only when the desired crushing rate in toss per hour is considered together with the rock size that the preference for one type over the other is truly significant. When Taggart completed his Handbook of Mineral Dressing there were already in opera-

Jan 1, 1985

By Edward F. Fries

Computerized, real -time monitoring had its beginning in the U.S. coal industry in the early 1970's. Over the last 10 years, developments in technology have made systems available that are capable of monitoring and controlling many mine parameters that can increase safety and production. However, situations currently exist where computerized monitoring systems are not being utilized to their fullest capability. They produce reams of printed output that are not sorted in a useful format, and human operators are not able to react fast enough in emergency situations tn tile large amount of information that the systems generate. A solution is the application of an expert system as the interface with real-time monitoring. An expert system would use an extensive knowledge base and human-type reasoning ability to make decisions on optimum strategies. Expert systems have been applied successfully to problems in other industries, and could provide significant benefits to mine information management systems. The use of an expert system with real-time mine monitoring is discussed in this paper.

Jan 1, 1986

By R. W. Hutson

One of the fundamental precepts of experimentation is the isolation of a single variable to quantify its individual effect. Unfortunately, the variability of natural rock joints has frustrated such isolation. This variability and the high cost of securing a large member of natural joints has lead to increasing experimental dependence on stage shearing, artificial tension fractures and/or model materials. The new apparatus described herein allows for the first time replication of real joints with field scale asperities. It employs a diamond band-saw blade with computer controlled feed table to cut joints with high precision. The feed system is capable of placement to tolerances similar to those of a high quality computer plotter. The accompanying software allows the table to cut any desired joint shape (repeating or non-repeating) within certain, over-all size limitations. Resulting joint surface dimensions and roughness as well as shear resistance indicates that the joint surfaces are reproduced with a precision similar to that possible for the control of other experimental variables such as normal and shear forces.

Jan 1, 1986

By J. K. Mokka, P. D. Rao, H. K. Lin

Extensive exploration has resulted in delineation of a massive sulfide district on the north flank of the east-central Alaska range. The district covers approximately 400 mi2 and contains numerous stratiform, transposed and some replacement type sulfide deposits ranging in size from less than 1 million st to 20 million st. Five types of ores were sampled for the study. Mineralogical analysis revealed that the minerals are too fine grained for conventional grinding and beneficiation. Hydrometallurgical studies were conducted using ferric chloride as a lixiviant. Ore microscopic studies as well as electron microprobe analyses of minerals in the raw samples and leach residues explained the low recoveries for certain elements as well as sources of impurities that need to be eliminated from the process streams.

Jan 1, 1992

By S. B. Patton, T. Novak, R. L. Sanford

A comprehensive approach to the development and organization of an expert system designed to assist electricians in diagnosing electrical faults in mining machinery is discussed. The system includes diagnostic, reference, and tutorial programs. The diagnostic portion of the system is based on a causal-reasoning approach, which is used to establish a hierarchy of symptoms and the subsequent production rules for identifying component-level failures in the motor-control circuit of a shuttle car. With this approach, conclusions are developed directly from knowledge of the circuit and its behavior (in both working and failure modes) based on first principles, rather than the heuristics of a domain expert. The symptoms and their hierarchal structure are formulated by creating "what if' scenarios and performing a qualitative circuit analysis for each fault. Techniques for incorporating interactive graphical displays of the circuit schematic into the diagnostic portion of the system are also presented. Supportive computer programs that provide reference material and tutorials on the circuit are also described.

Jan 1, 1990

By O. A. Bascur

In recent years, metal-producing companies have increased their investment in automation and technological innovation, embracing new opportunities to enable transformational change. Transformation to a digital plant can fundamentally revolutionize how industrial complexes operate. The abundant and growing quantity of real-time data and events collected in the grinding and flotation circuits in a mineral processing plant can be used to solve operational issues and optimize plant performance. A grade recovery model is used to identify the best operating conditions in real time. A strategy for increasing the value of instrumentation in current plants is reviewed. An optimal Gaudin size distribution model provides augmented information from traditional sensors to find the optimal grind cut size to reduce metal losses in the flotation circuits. Sensors in flotation circuits enable an estimate of the recovery and determination of the optimal froth depth and aeration using an air hold up flotation model. A strategy of classifying data for online generation of insights to using operational intelligence tools is described. The implementation of a recovery/grind strategy with industrial examples in nonferrous mineral processing is presented.

By Alden B. Carpenter

The Dead Sea is the only relatively large body of surface water having bromide concentrations comparable to those in the brines of the Smackover Formation in Arkansas. The Dead Sea, like the Smackover brines, contains a great deal of calcium and is very low in sulfate and iodide. The relationships between potassium, divalent cations, and chloride indicate that over 20 percent of the bromide in the Dead Sea is derived from some source other than by the evaporation of sea water. A similar type of study of the Smackover brines in Arkansas indicates that approximately 60 percent of the bromide has been derived from some source other than sea water. Both the Dead Sea and Smackover brines are very low in iodide suggesting that the excess bromide has not been derived from organic matter. The origin of the excess bromide is probably the same for both of these brines, but the source of this bromide remains unknown.

Jan 1, 1978

By G. F. Friel, J. C. Edwards, C. C. Hwang

In the implementation of a mine fire alarm and location strategy, the Interpretation of the fire signature Is Important. Smoke and CO are the two dominant fire signatures, and many mine fire detection systems utilize sensors which respond to smoke or CO through a diffusion mode or a mechanical pump mode. The fire signature may be modified during its transport along airways and at crosscuts. The modification occurs through dilution of the contaminants. In this Investigation, computer codes were employed to compute the effects of contaminant dilution on the contaminant signature when a straight flow passage has one dead-end crosscut. The model predicted the airflow within always and the entrainment of contaminants into the crosscut from the airway. One application of the model is to determine the most suitable location for CO detectors for early mine fire detection.

Jan 1, 1995

By W. E. Horst

Raw materials and mineral products are crushed, ground, or pulverized for a variety of reasons. Some of the most important reasons for size reduction are: to liberate marketable mineral species from a matrix of commercial minerals and gangue, to promote rapid chemical reaction through exposure of large surface area, and to produce a material with desirable size characteristics for handling, utilization, and storage. Comminution processes are currently used on vast tonnages of raw material annually. In the mineral industries where mineral products and other solids are processed, the various size-reduction unit operations represent a major portion of the manufacturing costs. The comminution process is an expensive unit operation from the stand- point of both capital and operating costs. Power consumption is large, and the energy conversion to useful work is very small regardless of the size-reduction system. In energy terms, about 1% of the all electricity generated throughout the world is expended in crushing and grinding operations by the cement industry alone. Comminution is a general term for size reduction that may be applied without regard to the actual breakage mechanism involved. General type of size-reduction equipment include crushers, tumbling mills of various type, impact mills, fixed-path mills such as a roller mill, and fluid-energy mills. Some comminution machines accomplish

Jan 1, 1985

By R. F. Kovar, R. N. Torbin

Foster-Miller has recently developed a new concept for a highly specialized shaft lining system. This innovative shaft lining system uses a continuous slip forming placement technique, lining the shaft from the bottom up such as in a raised bored shaft. Although this part is not unique, the concept is designed to use polyurethane foam instead of concrete for the liner material. Furthermore, the concept is designed to attain rates of advance of 30 m/h (98 fph). The polyurethane foam liner is designed to be thinner (100 mm or 4 in.) than a conventional concrete liner (300 mm or 12 in.). It will eliminate the high cost associated with the erection and operation of an on-site concrete batch plant. The system will be designed to operate remotely, requiring few personnel for its operation. This system (or parts of it) may be appropriate where fast construction speed is required or where a jointless liner is needed.

Jan 1, 1990

By L. R. Shotwell, C. F. Voss, R. J. Bastian

Pacific Northwest Laboratory (PNL) currently supports the U.S. Department of Energy's Office of Civilian Radioactive Waste Management in developing and evaluating analytical methods for assessing the suitability of sites for geologic disposal of high-level radioactive waste. The research includes consideration of hydrological, geomechanical , geochemical , and waste package components and the evaluation of the degree of coupling that can occur between two or more of these components. The PNL effort and those of other research groups investing potential waste sites in the U.S. and abroad are producing a suite of computer codes to analyze the long-term performace of the proposed repository sites. This paper summarizes the ongoing research in rock mechanics at PNL involving flow through jointed rock. The objective of this research is to develop a methodology for modeling the coupled mechanical-hydrological process of flow through joints and then attempt to validate a "simple" model using small -scale laboratory test data as a basis for judging whether the approach has merit. This paper discusses the laboratory tests being conducted to develop s joint behavioral constitutive model for the numerical method under development and the modeling approach being considered.

Jan 1, 1986

By Houston Kempton, David Atkins

Mining in semi-arid climates can produce environmental impacts that will not begin for hundreds of years, but once started, may continue for thousands of years. Pit lakes may eventually exceed toxicity thresholds as metals are evaporatively concentrated, and slow unsaturated flow through acid-generating waste can eventually load several kg-SO4/m2-yr to underlying water tables. U.S. regulations are poorly equipped to respond to delayed and long-term environmental impacts, delaying permits as operators and regulators grapple with uncertainty. Improved uncertainty analysis, additional long-term mitigation options, and explicit regulatory guidance offer solutions to this dilemma.

Jan 1, 2000

By Z. T. Bieniawski, D. A. Newman

The Geomechanics Classijication (RMR System) (Bieniawski, 1979) was modified for entry and roof support design in underground coal mines. Adjustment multipliers were introduced to incorporate the influence of high horizontal stresses and the roof support reinforcement into the existing classification system. Sixty- two case histories of standing and fallen mine roof were collected from two mines in the northern Appalachian coalfield. Twenty-seven engineering and geologic parameters were recorded for each case. A partial correlation analysis was carried out on the cases to establish which parameters have a significant im- pact on the stand-up time of supported coal mine roof. Survival analysis, a statistical technique used in medical research to assess the effect of a drug or treatment on a patient's life expectancy, was conducted together with stepwise multiple regression to derive values for the adjustment multipliers. A practical example is included to illustrate the application of the modified Geomechanics Classification to underground coal mine design.

Jan 1, 1987

By Patricio A. Espinoza, Aldo Casali, Cristian Ardiles, Guillermo González

Cluster analysis is used to design grade soft-sensors in a rougher flotation plant and a ball mill overload soft-sensor. Soft-sensors are virtual sensors which either replace unavailable actual sensors or infer measurements for non existing sensors. In the case of the grade soft-sensors clustering serves to determine clusters of related operating points. To each cluster there corresponds an ARMAX model structure whose parameters are estimated using only the points in the corresponding cluster. Thus a much better correlation is found than if all the data points were used for a global model. The problem of identifying clusters when the measurement of the real sensor is not available is addressed. In the case of the overload soft-sensor, variables were selected which are related to overload, either from a phenomenological point of view or according to operator experience. Different clusters are formed, some of which are identified as determining an overload condition or a possibility of such condition. Each of these clusters has a set of operating conditions which suggests the corrective action to be taken when necessary. Both kinds of soft-sensors are tested with industrial plant data and promising preliminary results are obtained.

Jan 1, 1995

By Neville G. W. Cook, John Kemeny

Utilizing the principles of elastic-brittle fracture mechanics, stress-displacement relationships are derived for an elastic solid containing a slip plane consisting of various configurations of collinear arrays of cracks. These models take into account the heterogeneous nature of slip planes as observed in the lab and in the field, and are relevant to the behavior of rock containing faults, joints, bedding planes, and fractures. All of our models exhibit slip weakening behavior, and show regimes of both stable (aseismic) and unstable (seismic) deformation. For given configurations of cracks and applied boundary conditions, our results show explicit ly the energy released through unstable crack growth. For instance, it is found that two equal length cracks growing together release more seismic energy than, say, a large crack growing into a small crack. Also, by allowing cracks to coalesce, our models show multiple stick-slip events without crack healing or other geochemical means.

Jan 1, 1986