Search Documents

By John E. Urbanic, William D. Faulkner, Robert W. Ruckel

Guidelines are presented for the selection, handling and regeneration of activated carbon used in gold recovery operations. The guidelines are based on Calgon Carbon Corporation's own investigations and experience gained in working with gold mine operators all over the world. Gold adsorption rate and adsorption capacity are shown to be independent variables thereby requiring testing of both properties when selecting activated carbon. Means of measuring these properties are provided. Historical activity tests on activated carbon are shown to be minimally useful in selecting carbon for gold recovery. Proper thermal regeneration techniques to maximize recovery of adsorption rate without weakening the carbon structure are suggested. Simple positive means of measuring efficiency of regeneration are presented. The subject of hardness measurement as a predictor of "in process" abrasion is discussed. The cost/benefit issue of carbon activity level is addressed.

Jan 1, 1986

By J. Finch, J. Yianatos, N. W. Johnson, R. Espinosa-Gomez

A method of determining the maximum concentrate solids rate or carrying capacity is described for given column operating conditions. The method requires alteration of the feed rate of solids to the column at a fixed residence time by manipulation of the % solid of the column feed pulp or the bias rate. The carrying capacity was measured for five streams at the Mt. Isa Mines Pb/Zn and Cu concentrators. As a potential scale up parameter, the mass of solids per unit time per unit column cross section (Ca, g/min.cm2) is explored. Ca is tentatively related linearly to the 80% passing size (d80) of the concentrate. For d80 < 15 pm Ca was less than 4 g/min.cm2 (8 lb/min.ft2) which makes it a critical consideration in scale-up for such fine feeds. An alternative carrying capacity parameter, mass of solids per unit volume of gas Cg was not as useful as Ca since Cg varied inversely with gas rate.

Jan 1, 1988

By V. E. Ross

A model has been developed that describes the behavior of mineral particles and water in the cleaning zone of flotation columns. The possible detachment of particles from their sites of attachment at the bubble surfaces is related to the flux of bubble surface area with increasing distance from the interface between the collection and cleaning zones and the late at which floated particles are transported into the cleaning zone. The drainage velocities of floated and entrained particles are calculated from the drainage velocity of water and the properties of the particles. The effects of wash water and inhibited drainage in the froth are also explicitly accounted for.

Jan 1, 1988

By R. Larry Grayson

A survey of 1250 surface and underground coal mines across the United States was made according to a stratified sampling technique based on national coal districts. A total of 171 responses (13.7% response rate) have been returned and summarized, giving a picture of computer usage in the coal industry. Overall, 63.5% of the respondents use computers, but the percent varied from 100% for large mines to only 44.1% for small mines. As expected, a proliferation of microcomputers has pervaded the industry. Importantly, in spite of the high usage of computers in the industry, sophisticated engineering applications have not yet burgeoned.

Jan 1, 1989

By J. F. Able, F. Djahanguiri

The US Bureau of Mines conducted research on underground stope leaching of metalliferous ores. Leaching underground would minimize the environmental impact of ore processing on the surface and would maximize minable reserves. An important aspect of this process is the minimization of pregnant solution losses and groundwater contamination by leach solutions. Bulkhead design and construction are important issues for solution control and stope-leaching economics. A reinforced-concrete bulkhead was designed, constructed and tested for solution control in an underground mine near Idaho Springs, CO. This paper presents the bulkhead-design methodology and construction procedure.

Jan 1, 1998

By K. Hanumantha Rao, K. S. E. Forssberg, H. R. Manouchehri

The fundamentals of electrical separation, the electrical properties of minerals, the principal methods used for charging minerals and their mechanisms, the effective factors controlling the acquisition of charges by minerals, the general configuration of commercial electric separators and the forces operating during electrical separation of minerals are reviewed and presented.

Jan 1, 2000

By L. A. Puchkov

Problems of how to use artificial intelligence (AI) methods and expert systems (ES) to control complex industrial projects have lately become significant in practical terms. Mining ventilation systems undoubtedly belong to complex multi dimensional objects of control with stochastic nonstationary and nonlinear processes. Formal models based on automated ventilation control, do require awkward algorithmic solutions, moreover, a number of tasks become the operator&apos;s headache, and the quality of their solution depends on his experience and intuition. These tasks include: - identifying pre-accidental situations and determining their causes; - making well-grounded decisions with regard to changing ventilation regimes, forecast of mining operations taken account of; - controlling ventilation systems in emergency situations, e.g. when in accident, etc. It is in this context that we have for a number of years been investigating how to practically use AI methods for operative control in dynamic aero-and-gas mining processes, one of our research directions being devoted to working out a consulting programme for the ventilation system operator. Our researching and modeling problem was identification of aero-and-gas situation in different parts of ventilation network and its interpretation in order to determine possible causes for gas regime changing and unexpected consequences. We would single out the following stages in this task: I. Operative information procession coming to the data base from the sensors and analysis of hypothetical versions (using the associative rules base) with regard to factors which have caused significant parameter fluctuations (e.g. C%(t), H(t), Q(t) etc.)., 2. Selection of hypotheses in the knowledge base and forming conclusions in accordance with reliability scale. 3. Clarifying the obtained conclusions in dialogue with the operator. 4. Correcting the associative rules base.

Jan 1, 1992

By R. S. Conti, L. L. Chasko

To deal with an unexpected event such as fire, prevention and preparedness are important elements in an underground mine&apos;s strategic plan. The purpose is to prevent afire before it initiates and to be prepared to deal with it when it does occur. This paper highlights a technology that may be used by the mining workforce to minimize such occurrences. It discusses thermal imaging cameras and their many applications to detect equipment failures or hot spots before they develop into afire. It also evaluates the feasibility of using thermal imaging cameras for emergency responders to assist them during exploration, rescue and fire fighting efforts. These thermal imaging systems allow rescue personnel to see in darkness and through dense smoke, thus making it easier to locate heated areas and missing or trapped personnel.

Jan 1, 2003

By Charles N. Alpers, D. Kirk Nordstorm

A variety of approaches have been used in the recent literature for the estimation of pre-mining (or natural background) metal concentrations in areas affected by mining. The following is a list of some of these approaches: (1) historical and anecdotal data, (2) remote analogues (other similarly mineralized areas), (3) proximal analogues (nearby mineralized areas), (4) sediment sampling (streambeds, lakes, estuaries, floodplain deposits, and soil profiles), (5) stable isotopes (hydrogen, oxygen, sulfur, and carbon), (6) geochemical modeling (forward, equilibrium-based), (7) geochemical modeling (forward, kinetic- and transport-based, and inverse), (8) statistical analyses, (9) mass balance on oxygen flux, (10) mass balance with age determination of weathered material. Examples of each approach are described, and the strengths and limitations of each approach are discussed.

Jan 1, 2000

By M. H. Al-Dabbagh

In this paper, the authors outline the deficiencies of PERT/CPM as a method for scheduling complex projects such as mine development. In particular, PERT/CPM networks cannot accommodate logical nodes (events) or stochastic branches (activities). The Graphical Evaluation and Review Technique (GERT), developed by Pritsker and. co-workers, is introduced as an alternative to PERT/CPM that overcomes many of the deficiencies of the latter and enables a more realistic analysis of complex projects that are subject to significant uncertainties. A brief overview of GERT network structures and network analysis is given and a PC implementation of the method is described. The technique is illustrated by application to the development of an open-pit gold mine in Saudi Arabia.

Jan 1, 2002

By Terry Ritzel

Predictive maintenance technologies include vibration analysis, tribology, infrared thermography, ultrasonic detection and electrical measurements. These technologies have been applied to large electric mining shovels at the Cyprus Sierrita Mine outside of Tucson, AZ. The predictive maintenance program was initiated on the P&H models 2300 and 4100 electric shovels during August 1996. Results of these technologies have shown the potential for improving electric min- ing shovel availability and minimizing maintenance costs. Predictive technologies provide the tools to assess machinery condition. Availability is enhanced by the condition-based planning of component replacement. Maintenance costs are minimized by focusing resources through condition-based prioritization.

Jan 1, 1997

By Agne Rustan

INTRODUCTION This work is a continuation of the preparatory study by Rustan and Stöckel 1979 (3) and (4) of the possibilities to introduce automatic mine ventilation in Swedish mines and construction works. The preparatory study has been financed by the Swedish Board of Technical Development. In the study it was recommended that an automatic step by step control of the fans near the working place due to diesel exhaust emission would be the best solution. A more advanced alternative would be to regulate the fresh air continuously in proportion to the contamination. The latter alternative has been studied by Boliden Mineral Co in the Udden mine. In this study it was found that the air supply could be regulated continuously but it was very important where the sensors feeling the contamination were placed. An intense study of the environment underground is now being planned by our division together with specialists from the National Board of Health and Safety, The Swedish Work Environment Fund, LKAB and the local Governmental Inspection of the Workers Safety. Different gases, radon, dust, airspeed, moisture temperature and pressure is planned to be measured continuously and correlation between the parameters is going to be established to decide the best measurement parameters for regulating the system. The best situation of sensors is also going to be studied. Despite this work hasn&apos;t been done yet this paper covers some of the problems which could be encounted with continuous regulation. In this report the environment has been studied during the test with step by step regulation of fans by radio. Diesel vehicles are the largest polluters under ground in Swedish mines and we have therefore suggested that the large diesel vehicles should regulate the fans. The goal of this study has therefore been to find how active diesel vehicles should be able to start and stop gallery fans at both intake and return air. In this paper different methods for activating fans are discussed. Then the best methods are chosen and tested in the mine. In this study we have found that changes of temperature is a cheap and effective method to start and stop cross cut fans in sublevel caving and radio signals seem to be an attractive system for start and stop of gallery fans. This work has been done in close collaboration between LKAB in Kiruna and the University of Luleå - Division of Electronics and Division of Mining and Rock Excavation. A reference group for the project has been established with ventilation experts from the mines, representatives for the local mine worker&apos;s unions and authorities from the local Governmental Inspection of the Workers Safety. VENTILATION SYSTEM STUDIED In the project the ventilation system at LKAB in Kiruna has been studied. The mining method used is sublevel caving with 9-13 m slice height. The air is heated winter time over ground by hot water heat exchanger. The main fans are pushing air down to a main distribution level along the 4000 m long and about 100 m wide orebody. From the distribution level, air is taken through shafts down to the sublevels, where it is pushed through the levels by local gallery fans on both intake and return side, see fig 1. The air ( ~ 8 m3/s) is moving freely through the gallery head. The cross cuts are ventilated with smaller fans, diameter 500 mm, and flexible duct, see fig 2. The aim of this study has been to study how to start and stop gallery- and cross fans and examine the environment when the fans are stopped . In Sweden there are no regulations telling that a minimum of air amount must be supplied. Instead the hygienic limits must be fullfilled.

Jan 1, 1981

By Thomas E. Garnar

Zirconium and hafnium are the twin elements of the periodic table because they are always found together. They resemble each other so closely that hafnium was not discovered until 135 years after the discovery of zirconium. Zirconium was discovered by Klaproth in 1789 and isolated 35 years later by Berzelius. Because hafnium&apos;s chemical properties are so close to those of zirconium, it was not discovered until 1923 when Coster and von Hevesy detected it using X-ray spectrographic analysis. These elements occur most commonly in nature as the mineral zircon (ZrSiO,) and less commonly as baddeleyite (ZrO,). They also are found as a variety of other silicates. Zircon was identified as a component in alluvial and beach sands in 1895, but it was not produced in any quantity until 20 years later. During World War I, it was produced as a coproduct of beach sand mining for titanium minerals just south of Jacksonville Beach, FL, and was patented as a refractory. It was not until the 1930s, when Zircon Rutile, Ltd., began mining at Byron Bay on the east coast of Australia, that zircon was first used as foundry sand. Later in the 1940s, NL Industries and Humphreys Gold Corp. began production of zircon sands from fossil beaches in northeast Florida. Baddeleyite first became available as a commercial product in 1916, but never in the quantity of zircon. Zircon holds a unique position as an industrial mineral because it is used for both its physical and chemical properties and as an ore of zirconium and hafnium metals. Australia is the major zircon producer followed by the Republic of South Africa and the United States. Zircon is also produced in India, Sierra Leone, Sri Lanka, Malaysia, the former USSR, China, Thailand, and Brazil. The location of world zircon mines, baddeleyite mines, and undeveloped zircon ores are shown in [Fig. 1]. World production of zirconium mineral concentrates is shown in [Table 1].

Jan 1, 1994

In 1989, United States mine production of barite decreased 13% while world mine production decreased by 8.6%, according to the US Bureau of Mines. Consumption, sold or used by grinding plants, decreased by 21.2%. And imports decreased by 12.8%. The value of domestically produced barite, fob mine, increased 17.4%, according to the Bureau. The declared value cif US port of all imported crude barite during 1989 increased from $38.10/t ($34.56 per st) in 1988 to $40.27/t($36.54 per st). Nevada continued to be the leading producer of barite with 77% of the total, followed by Georgia and Missouri. The Bureau of Mines estimates 75% of the domestic mine production was used as a weighting agent in drilling fluids. The remaining 25% was used in barium chemicals, glass, or as a filler. Most of the production from Missouri, Georgia, and Tennessee was used in the nonoilfield sector. Of the total consumption used by grinding plants and chemical manufacturers, it is estimated that 80% was used in drilling fluids. The other 20% was used in the non-oilfield sector, including barium chemicals and fillers in paper, plastics, and glass. The tonnage consumed in the drilling fluids market decreased due to the lower average rig count during 1989. The average number of rotary rigs operating was 869, 7.2% less than the average of 936 in 1988. Crude barite imports were down 12.8% from 1988. Imports accounted for 73.8% of the barite consumed (apparent) in the US. China continued to be the leading exporter of crude barite ore to the United States with 63% of total crude ore imports. India followed with 27.4%, Peru 4.3%, Chile 2.9%, and Canada and Mexico, each with 1.1 %. About 97% of the imported barite ore was used in the oilfield sector.

Jan 1, 1990

By Ralph J. Holmes

INTRODUCTION Although sampling techniques used by the mineral industry continue to improve, sampling is still an area which is often neglected. Frequently, sampling and sample preparation requirements are left to personnel who do not fully appreciate the significance and importance of sampling. Consequently, plant evaluations are often based on seriously biased samples, leading to mass balance problems and incorrect assessments of plant performance. The basic rule for correct sampling is that each particle of ore or concentrate must have an equal probability of being collected and becoming part of the final sample for analysis. If this is not the case, bias is easily introduced and the sample is not representative. For example, when ore is travelling on a conveyor belt, the lumps may come to the surface. Consequently, a grab sample taken from the top layers only will contain a greater proportion of lumps, i.e., the sample is biased. There seems little point in making major investments in precise analytical equipment, if the sample provided to the analytical laboratory is not representative in the first place. This paper describes the sources of plant sampling errors, reviews the methods of estimating their variance, presents some worked examples, and provides some practical advice for reducing sampling errors and their variance. SAMPLING BASICS It is generally accepted that the discharge point of an ore or concentrate stream is the most suitable sampling location. The stream can be intersected at regular intervals, and representative samples, referred to as increments, can be obtained by taking a complete cross-section of the ore stream. On the other hand, sampling devices that take part of the stream on an intermittent or continuous basis, e.g., a bleed from a pipe, may introduce serious bias, and should be avoided at all cost. Increments may be taken at completely random times or tonnages during the sampling operation, in which case it is called "random sampling". However, as shown below, random sampling results in the largest sampling variance, so it is preferable to divide the ore or concentrate stream up into strata of equal time or mass and take one increment from each stratum. This operation is called stratified sampling and may be either systematic sampling, in which increments are taken at the same point in each stratum, or stratified random sampling in which the increments are taken at random within each stratum. Systematic sampling results in the smallest sampling variance, provided periodic variations in quality or quantity are not present which may coincide with, or approximate to, any multiples of the proposed sampling interval. In such cases, it is strongly recommended that stratified random sampling within fixed time or mass intervals be carried out.

Jan 1, 1991

By R. Kadeg, S. Pavlou

A methodology for developing and utilizing risk-based action levels for soils in site closures is discussed. The methodology is based on standard exposure pathway models which are consistent with current regulatory guidance on conducting risk assessment. A simple approach to evaluating the potential for contamination ground water from the projected criteria based on the Toxicity Characteristic Leachate Procedure (TCLP) is also presented.

Jan 1, 1992

By Sean Gallagher, Thomas G. Bobick, Richard L. Unger

This paper describes research by the Bureau of Mines on alternative materials-handling strategies for reducing the costs and incidence of back injuries in low-seam coal mines. Strategies recommended for redesigning materials-handling tasks include elimination of tasks, mechanization of tasks, and matching lifting tasks to the physical capabilities of underground miners. The report also discusses other methods that can be used by management to reduce the costs associated with back injuries. More detail can be found in Bureau of Mines Information Circular 9235 (Gallagher et al. 1990).

Jan 1, 1992

By Jacques Deraisme

Geostatistics has been applied in many mining feasibility studies throughout the world during the last decade. Recently geostatistics has begun to be applied to the field of mining processes by attempting to aid in the definition of the best mining policy. For a feasibility study the grade-tonnage relationships give a reasonable order of magnitude estimate of the ore reserves within the deposit. But the reserves that will actually be recovered, will vary depending upon the mining methods and the technical means used. The profit earning capacity of the mining project is determined by a great many factors, such as for instance: accessibility of reserves to extracting machines, the haulage distance between the mine and the mill, the variability of produced ore (tonnage and grades) which could necessitate stockpiles or blending areas?

Jan 1, 1979

By Betty L. Gibbs

Computer software for mining applications has been in development since before 1970. These packages cover tasks from exploration data management through final reclamation planning. These programs were originally written in Fortran and have evolved into colorful, user-friendly packages. Programs that produced printed symbol maps now show color, three-dimensional image of an ore deposit on a computer screen. Pictures can be rotated and looked at it from all directions and layers can be peeled off to show other parts of a model. Computer users have also evolved. In the early Fortran days, users had to learn computer operating systems, have someone punch data cards, set up run files and wait a day or so to find out if there was one little mistake somewhere that caused the program not to run. With today&apos;s technology, users sit at their desks in the office, key in some data, read other data from digital files and build a model within days, rather than weeks or months.

Jan 1, 1999

By R. L. Wiegel

Several mineral process modeling and simulation packages are currently available for use in evaluating the performance of alternative process flow schemes. A critical link that has been missing from these packages is the ability to quantitatively model the effect of size reduction on the liberation of the valuable and waste minerals in the ore being processed. Although there have been several approaches taken to this problem over the past 25 years, none of them has led to a satisfactory conclusion. A technique was developed for measuring the effective liberation characteristics of magnetic taconite ores, and a program was constructed that makes use of these liberation characteristics in simultaneously simulating both size reduction and mineral liberation as it occurs in tumbling mills. This is an especially important step in the modeling of magnetic taconite processes, where magnetic rejection of low-grade wastes between grinding stages mandates that a predictive capability be available. The current application is specific to magnetic taconite, but it is possible that a similar approach could be used for other types of mineral systems. Key words: Modeling and simulation, Size reduction, Mineral liberation, Taconite, Magnetic concentrator

Jan 1, 2003