Search Documents

By E. W. Cokayne

GENERAL DESCRIPTION OF THE METHOD The original application of sublevel caving was in ground so weak that it would collapse even in small headings when the support was removed. Heavily tim¬bered drifts were driven across the ore body; the timber was removed at the end of the drift, and the ore caved and slushed out. When dilution became excessive the next set was removed and so on. This method gave high dilution and poor recovery and was slow, but it was the only way to mine this type of ore body at that time. In more recent times the method has been adapted to stronger ground which needs to be drilled and blasted, so it is not a caving method as far as the ore is con¬cerned. However, the method does rely on the walls to cave and so the name sublevel caving has been retained. The method as presently generally applied is shown in Figs. 1, 2, and 3. Sublevels are established at approximately 7.6 to 12.2-m (25 to 40-ft) vertical intervals. They are usually accessed from a ramp system. A haulage drift is driven down the strike of the ore body, but in the waste. Production drifts are turned off the haulage drift and driven across the ore body on about 10.7-m (35-ft) horizontal centers. This divides the ore body into a geometrical pattern. Slot raises are driven at the end of the drifts near the ore-waste contact and the slot is expanded to the shape of the fan drilling. Up holes are drilled to break towards the slot at burdens of 1.2 to 1.8 m (4 to 6 ft). They are drilled past the next sublevel to the production drift im¬mediately above. When a sufficient number of fans has been drilled, production can start by blasting one or two fans at a time towards the slot. Load-haul-dump (LHD) units are used to muck the ore, which rills out into the drift. At first, when only a small area is mined, the walls may not cave, and the operation will be similar to open stoping. Later, sloughing from the walls will fill any voids created, and the ore after blasting will be con¬tained by the caved waste and gravitate downwards as mucking proceeds. This process is repeated in each of the production drifts as the face is retreated towards the haulage drift. When the top level has been retreated back a safe dis

Jan 1, 1982

By Jessica M. Wempen, Dallan J. Coons, Bailey S. Simmons, Michael K. McCarter

Gate-road yield pillars are subject to increases in stress as the longwall face advances toward the pillars. Increases in pillar stress can be inferred by measuring roof/floor convergence surrounding the pillar. This paper presents a case study of convergence measurements surrounding a two-entry gate-road yield pillar in the head gate of a coal mine. Convergence was measured over a six-month period, as the longwall face approached and passed the pillar. Measurements were collected at eight locations surrounding the pillar: four locations in the travelway and four locations in the beltway. In addition to convergence stations, the pillar was instrumented with an array of seismometers. In future analysis, convergence measurements will be compared to seismic interpretations. This study reports on the geology and geometry of the longwall panel, the roof and rib support, the change in convergence over time, and the physical properties of coal and parting. Additionally, the convergence measurements are compared to pillar safety factor distributions derived from a finite element model. The convergence measurements contribute to the knowledge of when yield pillar abutment loading, caused by the encroaching longwall, is first detected. Knowing when abutment loading begins to yield the pillars can help define when standing secondary roof supports are required for head gate entry support.

By V. K. Gupta

A detailed experimental study of the variations in grinding rate with particle size, particle load, ball diameter, ball load, mill diameter, and mill speed was carried out for a soft cement clinker and a hard cement clinker. The effects of the ball diameter, ball load and particle load were observed to be material (hardness) independent, and those of the particle size, mill diameter and mill speed to be material dependent. A sharp change in the grinding behavior was observed for both the clinkers at about 150 µm size. Below this critical size: (i) the hardness difference between the two clinkers became insignificant, (ii) variation in the grinding rate with particle size became markedly more pronounced, and (iii) mill speed had little or no effect on grinding rate. The importance of these results in the context of process optimization and control is discussed.

Jan 1, 1987

By C. C. Bailie

This paper will be concerned with those mineable coal measures at depths necessitating deep mine operations in the range of 200 feet to 800 feet in depth. The area is generally classified as the Southern Illinois Field but more specifically includes that part of the state south of a line extending from St. Louis, Missouri on the west to Vincennes, Indiana, on the east. This embraces an area which presently includes a total of 38 shipping mines and 5 local or truck mines. Of these shipping mines, 22 are deep (shaft or slope) mines and the remaining 16 are strips. The average annual production of the shipping mines is around 29 million tons. The presently classified mineable reserves of the area are estimated at around 70 billion tons.

Jan 1, 1964

By James R. Arnold

Gold Fields Mining Corporation started processing ore from it's Chimney Creek operation in northern Nevada in November, 1987. Since that time production has averaged about 200,000 ounces per year from the milling and dump leaching circuits combined. The events that led up to commissioning of the plant started in January of 1985 when the Gold Fields exploration team drilled their first hole in an area now known as Discovery Hill. The major orebody was located later in the year in what is currently the major focus of activity, the North Pit. Subsequent drilling since plant startup has found another 14 million tons of ore two miles south of the original orebody. This South Pit orebody is currently being stripped and metallurgical testing is underway. Engineering Engineering on the Chimney Creek plant started in earnest in May, 1986. Davy McKee Corporation from San Ramon, California, did both the engineering and the construction management. Before engineering began the entire senior staff of the Plant Department was hired and assigned to the project. Senior staff included the Plant Superintendent, Plant General Foreman, Maintenance General Foreman and Chief Metallurgist. Gold Fields does not employ an internal central engineering staff to design their plants. We feel that the people who design the plant should be the ones who will be required to run it once it has been commissioned. This philosophy affords a continuous accountability from start of design through commissioning and operations. All four of the senior staff spent the most critical phase of the engineering stage at Davy McKee, so the plant is truly a reflection of all four disciplines. In bringing on the Maintenance General Foreman from the start, there was a focus placed on ease of maintaining the plant. Another philosophy that was adopted from the start was that the plant be easy to work in and maintain for both operators and maintenance personnel. Numerous design criteria were given to Davy McKee to ensure this. For example, we required that every piece of equipment could be reached easily with a crane or fork lift. All conveyors were required to have walkways on both sides for ease of maintenance and a minimum of 30 inches of clearance under them for ease of cleanup. Visibility for operators was considered very important and the control rooms and general plant layout were designed with this in mind. A list of about 100 general rules were given to Davy McKee during the early layout meetings and these were held as the general design criteria throughout engineering and construction. While engineering was progressing in San Ramon, California, dump leach test work was being done at the site. Three 6 foot diameter fiberglass columns were constructed and filled to a 20 foot height with low grade ore. Leaching characteristics were determined and the dump leach design was based on information collected from these columns. Construction The major contractors on the project were The Industrial Company for the bulk of the piping and structural, EMKO on the electrical/ instrumentation and Hunewill for most of the earth work and leach pad construction. All plant operating and maintenance personnel were employed eight weeks before startup for intensive training. Instructors were Gold Fields personnel, including foremen, and Davy McKee engineers. On occasion, selected suppliers representatives were brought in to discuss major pieces of equipment. Project completion was targeted for January, 1988 at a projected cost of 78.9 million dollars. Actual startup was about 1 1/2 months ahead of schedule and slightly under budget. Full design capacity was achieved the first full month of operation. Crushing Run of mine ore is delivered to the crusher and dumped into a 90 ton hopper which is topped with a 30" X 30" opening stationary grizzly. Ore is fed to a 50" X 60" Telsmith jaw crusher with a 5' wide apron feeder. The closed size setting of the

Jan 1, 1989

In parallel work, the cyanide/silver impregnated activated carbon system was studied for the purpose of developing an alternate cyanide removal system. It was found that free cyanide can be reduced from 20 ppm to below 10 ppb with a fixed bed of silver impregnated activated carbon, since such cyanide removal might be applicable to gold mill effluents, the investigation was extended to the cyanide/gold impregnated activated carbon (GIAC) system. Batch tests were conducted varying the gold content of activated carbon, carbon/CN ratio, stirring speed, pH of the initial solution, and the reaction temperature. The adsorption isotherm of cyanide/gold impregnated activated carbon system was also studied. The results of these batch tests show that the behaviour of the cyanide/GIAC system is very similar to the cyanide/silver impregnated activated carbon system variation of the gold content of the impregnated activated carbon has some influence on the cyanide adsorption rate. The latter is mainly increased, however, by increasing the GIAC/CN ratio. The activation energy was determined to be 3.12 kca1/mole (13.08 kj/mole) and the Au(CN)2 saturation at 194 µ M/g NORIT ROX O.B. The experimental results of reaction temperature and stirring speed show that the adsorption of free cyanide on such activated carbon is controlled by pore diffusion inside the activated carbon particle or by surface reaction. The adsorption isotherm follows the linear model and it is favourable for the cyanide/gold impregnated activated carbon system.

Jan 1, 1994

By P. C. O. Chukabarah

Many aerodynamic and thermodynamic properties, such as temperature, pressure, velocity and density vary widely, and in random spatial and temporal manner for a given underground mine environment. Such variabilities are seldom evaluated statistically, even though the relevant theories and principles for such an approach are both available and feasible. The main purpose of this paper was to introduce the new methodology of applying aerostatistics to the analysis of multiple fan system in mine aerology and/or ventilation. Pertinent data were obtained from a small multilevel coal mine. Results proved and confirmed that aerostatistical methodologies are computationally more efficient, grounded in solid engineering statistical theories, and can be used to analyze networked parameters in mine environmental engineering.

Jan 1, 1994

By V. A. Scovazzo

The analytical pillar design procedure employing the Wilson equation is based on the site-specific material strength of the floor, pillar, and roof rock. Stable pillars so designed will sometimes be larger than those designed using empirical methods thus providing more stability or at other times smaller than empirically designed pillars thus conserving natural resources. Presented here is a detailed procedure for the analytical design of soft rock pillars using the Wilson Equation. An example of this procedure is presented that uses data from a mine in the Owl Seam in Southern Appalachia. These Owl Seam pillars are now in use and are performing as expected. Also addressed is an assessment of the Dr. Scovazzo?s analytically designed pillars based on pillar performance data gathered by Dr. Mark in the Southern Appalachian Coal Field.

Jan 1, 2010

By R. Bruce Tippin

Background Iron ore is the No. 1 metal mining industry in the U.S. with dollar value of $2.3 billion in 1984 (U.S.B.M Mineral Commodity Sunnnaries , 1985). However, during the past decade this nation's iron ore industry has been subjected to a major market depression and a correspondingly downward adjustment in output. The recent trend in the curtailment of iron ore production traces a slow-down of the country's steel industry. Both pig iron and steel production have decreased significantly over the past several years. These trends are shown in Figure 1 from data collected by the federal Bureau of Mines (U.S.B.M. Mineral Commodity Summaries, 1985; U.S.B.M. Mineral Industry Surveys 1986). The industry is presently operating at less than 60% of its annual capacity. The domestic steel industry has been forced by reduced profits or losses to close facilities, curtail operations and restructure the financial status of several corporations. Companies have been sold or are trying to sell selected properties to improve their financial circumstances. Even with such actions, many of the steel companies are in very serious straits, including the seventh largest steel company, LTV, which has filed for bankruptcy. Many of the major steel companies have financial interests in iron ore mining and thus their adverse economic conditions directly reflect those operations. Several iron ore producers have been shut down including Reserve Mining Company in May, 1986 and Butler Taconite in June, 1985. The latter recently filed for bankruptcy under Chapter 11. A1 so in mid-1986, U.S. Steel Corporation, owner of the Minntac mine and iron ore processing plant, underwent corporate restructuring. The effect on their Minnesota plant is not known at this time. An excellent summary of the interrelationship of the iron ore companies and the steel producers has been provided by Skillings (1986), and an analysis of the iron ore situation was given by Robert F. Anderson, CEO of M. A. Hanna Company, in his keynote address at the 1986 University of Minnesota Mining Symposium (Anderson, 1986). Steel imports to the United States decreased slightly in 1985 because of import restrictions, but the long-term import situation remains dim and uncertain. As shown in Figure 2, the imports averaged about 25% in 1985, and the preliminary indications are that this figure could be as high as 30% when the final 1986 information is collected by the U.S. Bureau of Mines. At best, the industry can only hope for imports to stabilize at a constant level in the near future. Although the tonnage is small, the quantity of U.S. export steel has fallen over 50%. With many other materials replacing steel , the projected demand through 1990 is expected to increase only about 1% per year. Consequently, 1986 U.S. iron ore production will probably be 15% lower than in 1985. The 41 mil lion tons of iron ore production expected in 1986 represents only 53% of the industrial capacity, which is about 74.5 mil lion tons. Over 95% of this iron ore is in the form of beneficiated pellets. Today there is not an iron ore producer west of the Mississippi River, nor is there any production in the South. The Birmingham (Alabama) iron ore industry has been shut down since 1971. The western producers ceased operations in the early 1980's. Only the taconite operations in Minnesota and the plants in the Upper Peninsula of Michigan remain as our major domestic iron ore source. The economic situation for both the iron ore producers and the steel industry can be described as confused and in turmoil. Such a condition directly impacts the iron ore processing plants' operations and plans for the future. Plant Practice At present the nation's eight major operating iron ore mines, listed below, are concentrated in northern Minnesota (Mesabi Range) and the Upper Peninsula of Michigan (Marquette Range). The only exception to the Minnesota/Michigan location is the Pea Ridge Iron Ore plant in Missouri, which is a subsidiary of St. Joe Mineral s.

Jan 1, 1986

By Henry H. Roos

NTRODUCTION In the mining industry, a "drill jumbo" is a drilling unit equipped with one or more rock drills and mounted on a mechanical conveyance. Jumbos range from single¬drill ring drills mounted on simple steel skids to sophisti¬cated multiple-drill units mounted on diesel engine powered carriers and equipped with automatic controls and sound-abatement cabs. Individual types of jumbos usually are designed for specific tasks such as fan drilling in sublevel caving operations. Some units, such as development jumbos, can be utilized for several functions in addition to their normal applications, e.g., for production drilling in room-and-pillar operations, stoping in cut-and-fill mining, etc. Mine operators can purchase individual components from manufacturers, assembling these components into a jumbo suitable for specific conditions. However, this requires that mine personnel have good engineering and mechanical abilities. Although manufacturers of jumbos maintain facilities for designing machines to meet con¬ditions created by new mining methods and unusual ap¬plications, the cost of the engineering and experimental work for new types of jumbos should be evaluated in terms of both costs and benefits; it may be advantageous to plan the mining operation so that existing and proven units can be utilized. GENERAL SELECTION CRITERIA Since the operating conditions vary in underground mines, the design of a jumbo must be selected to cope with the individual characteristics of the mine. The necessary considerations include access space into the working areas, grades expected to be encountered, radii of the curves, ambient temperatures, the characteristics of the rock, the acidity or alkalinity (pH rating) of the mine water, etc. Access to Mine Workings The mine workings must be accessible to the selected jumbo. Frequently, a jumbo must be disassembled at least partially to pass through the mine shafts. There¬fore, a bolted construction allowing disassembly into pieces of suitable size and weight is desirable in most applications. Type of Undercarriage Generally, a crawler-type undercarriage should not be used in trackless mines having acidic mine water. The acidic water causes an electrolytic action between the individual crawler parts and causes rapid corrosion and early failures. Propulsion A two-wheel drive on a pneumatic-tired jumbo is marginal for grades exceeding 12%. A four-wheel drive unit with good weight distribution is capable of operat¬ing on grades of up to 35%. At least 30% of the gross vehicle weight (GVW) should be carried on the steering axle; otherwise, the steering tires may not have sufficient traction on loose road surfaces and may "plow" instead of steer. To assure stable operation in mines with steep grades, the height of the center of gravity of the jumbo should be considered. It should not make the unit prone to rolling over on the steep grades that may be encoun¬tered. Turning Ability In confined working areas, a skid-steering or crawler unit has the best maneuverability. An articulated carrier is preferable when base-rotated parallel booms are being utilized. A rigid-frame jumbo with automotive steering is compact and economical, having lower maintenance requirements than the other two types. However, the turning radius of a rigid-frame unit is wider than either the skid-steering or articulated units, and this wider turning radius may be detrimental in mines with narrow drifts. JUMBO COMPONENTS Rail Undercarriages A mine with a rail-transportation system generally utilizes drill jumbos that are mounted on rail-type under¬carriages. With a light load and good weight distribu¬tion, this carrier may consist of a simple two-axle four-wheel platform onto which the boom-mounting brackets are attached. As the depth of the round and the penetration rates increase, the weight of the equip¬ment installed on the chassis also increases. The greatest problem with a heavy overhung load is balancing the carrier; a three-boom unit may require a substantial amount of counterweighting to maintain an acceptable 70% to 30% axle-load balance. Although lengthening the wheelbase helps balance the unit, a long wheelbase increases the turning radius, often creating problems on curves and sometimes requiring a swivel truck-type chassis. A good rule of thumb for a simple four-wheel undercarriage is to maintain a wheelbase length to track gage-width ratio that does not exceed 2.5 to 1.0. For a larger ratio, a swivel truck should be utilized. Swing-out outriggers or roof jacks help keep a jumbo in place during the drilling cycle. Usually, a rail-mounted jumbo is not self-propelled. Instead, it is maneuvered into place by a locomotive. Occasionally, several headings are being advanced in close proximity, and a self-propelled jumbo is con¬venient. In electrified mines, such a jumbo utilizes conventional battery-powered traction gear; in dieselized mines, hydrostatic drive components offer good flexi¬bility. The tractive power requirements of a typical rail jumbo may be calculated from the formula: HP = [(RR + GR) X Sl/[33,000 X Em X Eh]

Jan 1, 1982

By D. W. Park

Longwall mining is popular in underground coal production in the United States due to higher production rates and safety concerns. Because of the extreme complexity, it is necessary to plan an adequate design to achieve a safe and efficient working place. The proper sizes of yield and abutment pillars and panels can be determined by simulation using numerical modeling techniques. By means of three-dimensional modeling, stresses to be imposed on the pillars, panels, gob, and powered supports can be analyzed. In this study, an initial three-dimensional finite element model was developed and then modified into four different models. Using these models, the numerical outputs of distributed stresses on three different sizes of yield pillars, three different sizes of panels, and two different sizes of abutment pillars were compared and analyzed to determine the most adequate pillar and panel sizes. Progressive failure theory based on the Hoek and Brown failure criterion was used to determine redistribution of stresses in the yielded and failed areas in the longwall mine.

Jan 1, 1992

By Erhard M. Winkler

The rapid decay and disfiguring of stone monuments in urban and desert rural areas has challenged conservators to protect stone surfaces from premature decay. They attempt to halt the natural process of stone decay and possibly to restore the original strength lost mostly by chemical weathering and the loss of binding cement. Ageneral solution is not possible because the physical and chemical characteristics must be considered for different stone types. The failures of stone preservation and restoration are greater in number than the cures. The need for repair of stone decay goes back to evidence of Roman replacement of decaying stone. The presence of excess water in buildings has long been recognized. Moisture tends to enter masonry from air in humid climates, a most important but often underrated factor (Fig. 1) suggesting that sealing should be the answer. Undesirable staining and efflorescence result in accelerated scaling. Today, the great variety of chemicals available to the modem conservator for sealing. consolidating, or hardening stone fall into two very different categories: surface sealers and penetrating stone consolidants, or a combination of both. SEALERS Sealers develop a tight, impervious skin which prevents access of moisture. Surface sealing has saved monuments from decay by eliminating the access of atmospheric humidity. Pressure tends to develop behind the stone surface by moisture escape. Efflorescence, crystal growth action, and freezing can cause considerable spalling (Anderegg, 1949). Flaking results when moisture is trapped behind the sealed surface. Yellowing and blotchiness are also frequently observed. The following sealants are in common use today: linseed oil, paraffin, silicone, urethane, acrylate, and animal blood on stone and adobe. Extensive cracking and yellowing has resulted soon after application. In the past many such treatments have created more problems than cures: 1. Linseed oil and paraffin have been in use for centuries. Embrittlement and yellowing occur rapidly because these are readily attacked by solar ultraviolet radiation. 2. Animal blood as paint has temporarily waterproofed adobe mud and stone masonry. The origin of blood paint has a religious background rooted in the Phoenician and Hebrew cultures. Instant water soluble dried blood can substitute for fresh blood. Winkler (1956) described the history and technique of the use of blood. 3. Silicones have proven very effective and are long lasting. In contrast, acrylates, urethane, and styrene are generally rapidly attacked by UV radiation (Clark et al., 1975). Sealing of Different Rock Types Granitic rocks have a natural porosity traced to 4.5% contraction of quartz, during cooling of the parent magma, compared with only 2% contraction of all other minerals; protection against the hygric forces may require waterproofing of granite in some in- stances. The Egyptian granite obelisk in London is an example. Soon after its relocation from Egypt to London, Cleopatra's Needle was treated, in 1879, with a mixture of Damar resin and wax dissolved in clear petroleum spirit; surface scaling became evident after half a year of exposure to the humid London atmosphere. The treatment of the ancient granite monument from Egypt has denied access of high relative humidity (RH) in London to the trapped salts inherited from the Egyptian desert and has protected the monument from decay (Burgess and Schaffer, 1952). The sister obelisk set up in Central Park, New York City, has fared less favorably because similar treatment was done too late, only after the salts hydrated and hundreds of kilograms of scalings disfigured the obelisk surface (Winkler, 1980). Surface coating of other common stones may be needed. Crystalline marble absorbs moisture from high RH atmospheres: dilation may ensue when curtain panels bow as the moisture starts to expand during daily heating-cooling cycles. A good sealer may prevent the moisture influx provided that no moisture can enter from the inside of the building. Limestones, dolomites and all carbonate rocks are subject to dissolution attack by rainwater, especially in areas where acid rain prevails (Fig. 2). The interaction of sulfates in the atmosphere with the stone can be halted by waterproofing to avoid the formation of soft and more soluble gypsum. The stone surface attack can be diminished if nearly insoluble Ca-sulfite crusts can form, instead of Ca-sulfate. Replacement of fluorite or barium compounds at the stone surface acts as a hardener, rather than a sealant. Sandstones have generally high porosity and rapid water travel can occur along unexpected routes and from any direction. Any surface sealing may do more damage by scaling and bursting than if the stone is left without treatment. Sealing of sandstones is therefore not advised at any time. Testing the efficiency of sealants: Several authors discuss waterproofing materials, silicones, urethanes, acrylates and stearates, as to their water absorption, spreading rates of water on the treated surface, water vapor transmission, resistance to efflorescence, and general appearance (Clark et al., 1975). De Castro (1983) measured the angle of contact of a microdrop (0.004 cm3) on a stone surface as characteristic of the wettability. Laboratory tests and limited field performance are described by Heiman (1981). The crest of a Gothic sandstone arch, which was sealed with silicone,

Jan 1, 1994

By M. Moats, J. Young

Short term laboratory cell electrorefining experiments were performed to examine the impact of electrolyte composition, current density and temperature on deposit structure, roughness, and adhesion to 2B mill finished 316L stainless steel. Copper electrodeposits were produced using synthetic electrolytes with thiourea and the continuous addition of glue. Deposit structures were evaluated using X-ray diffractometry. Surface roughness was measured using profilometry and analyzed using scaling analysis. Finally, an internally developed method was used to measure the force required to remove the electrodeposited copper from stainless steel to determine adhesion strength.

Mar 2, 2022

By James Watson Baxter

Fluxes are used to promote pyrometallurgical processes that rely on adhesion (soldering or brazing) or fusion (gas and arc welding) to join metallic surfaces. In the adhesive processes, the metal surfaces to be joined are not melted; the join is formed using a filler metal with lower melting point than the base metal. Fusion welding involves use of heat in excess of the melting point of the base metal. The fused joint may be achieved either by simply fusing together metal surfaces brought in contact with each other or by introducing additional molten metal of similar composition to form a fused joint. ADHESIVE PROCESSES--SOLDERING AND BRAZING In order for molten filler metal, solder or braze, to spread in a manner that creates a successful join; the work surfaces on the base metal must be thoroughly cleansed. Fluxes remove stubborn oxide films and other surface contaminants, promote wetting of the work surfaces, add fluidity to the solder or braze, and enhance workability and ease of spreading. Brazing processes involve higher temperatures than those reached in soldering. Brazing fluxes, which must remain active and effective at the higher temperatures, differ from those employed in soldering. Some common fluxes used in adhesive processes are rosin for soldering tin and electrical connections, hydrochloric acid for use in soldering galvanized iron and other zinc surfaces, and borax for brazing. Soldering and brazing are similar processes, the primary difference being the temperature at which the joining operation is carried out. Soldered joints, produced with low-melting-point fillers (solders) that melt and flow at temperature less that 450°C (Althouse et al., 1988) can sustain loads of 1 to 1.7 MPa for extended periods of time (Anon., 1966). Brazing involves the use of filler materials with melting points commonly above 500°C and generally provides stronger joints than those obtained with solder. Both processes require local application of heat to melt and spread the filler so that the molten filler can wet (adhere to) the base metals by alloying and diffusion. Soldering Soldering is a means of joining metals by adhesion using a metallic bonding alloy as the filler, commonly a mixture of lead and tin. However, the adhesion of solder depends more on its ability to be keyed into minute surface irregularities than on alloying. The most familiar application is to provide and secure electrical connections. Soft solders can range from 1 to 70% tin with the remainder mostly lead. However, for general-purpose, soft-solder work, the alloy is commonly 50% lead-50% tin. Higher lead contents provide a wider range in the melting temperature and, for this reason, a 60% lead-40% tin alloy, which yields a mushy mixture, is used for wiped joints in lead sheet and pipe work. Conversely, 40% lead-60% tin alloys are used in soldering tin and other low- melting-point materials for which a narrower range of melting temperature is required. There are numerous other solder compositions such as tin-silver, 95% tin-5% silver and antimony-tin, 95% tin and 5% antimony (Carlin, Jr., 1992). Heat needed to melt and spread the solders is commonly provided by electrically heated, copper-tipped soldering irons or by means of torches; the solder is applied by hand, usually face-fed by means of wire. For wiped joints in plumbing and lead-cable splicing, the solder is manipulated with cloth pads. The molten solder wets the joint surfaces and is drawn, by surface tension, into minute fissures and capillary openings. Other applications involve use of induction heaters and furnaces with pre-shaped solder appropriately placed prior to fluxing and heating. In some processes, the joints are immersed in molten solder. Constituents and Role of Soldering Fluxes: Soldering fluxes generally fall into one of three categories: highly corrosive fluxes, intermediate fluxes, and noncorrosive fluxes. These same categories are sometimes designated inorganic, organic and rosin-based respectively (Althouse et al., 1988). Common constituents of each group are discussed briefly below. Corrosive Fluxes (Inorganic). Work with aluminum, magnesium, stainless steel, high alloy steel, aluminum bronzes, and silicon bronzes is carried out at temperatures in the upper portion of the range for solder operations. Soldering these materials requires use of highly active, corrosive fluxes to remove and prevent the formation of the especially stubborn, hard, oxide films that form on these materials upon exposure to the atmosphere. The corrosive fluxes consist of inorganic acids and salts that are applied either as pastes or dry. They are active at elevated temperatures and, since they remain active after the soldering is completed, must be completely removed. The main constituent of most corrosive fluxes is zinc chloride with a melting temperature well above the solidus temperature of most commercial tin-lead solders. It is made by the action of hydrochloric acid on zinc. When zinc chloride is used alone, un- melted particles of this corrosive salt get caught up in the joint and weaken it. For this reason, other inorganic salts such as ammonium chloride (NH4Cl) or sodium chloride (NaCl) may be added to lower the melting temperature. A mixture of zinc chloride and ammonium chloride is very effective because the excellent oxide reducing properties of ammonium chloride and the protective action of the molten zinc chloride combine to produce a fluxing action superior to that achieved when either is used alone. In addition to zinc chloride, ammonium chloride, and sodium chloride; common con-

Jan 1, 1994

By L. B. Guo, S. S. Peng

A hybrid boundary element-finite element model was formulated to model roof-bolt reinforcement of roof strata with bedding planes. This model was used to analyze the stress distribution around a rectangular opening, with variables such as opening width-height ratio, number of bolts installed, number1 location of bedding planes, in-situ stresses, etc. The most critical areas are identified, and the number and length of roof bolt required are then determined. Two case examples are illustrated.

Jan 1, 1991

By J. B. Hiskey, X. H. Jiang

The extraction of gold from chloride solutions by ion exchange is examined. It is shown that at initial gold concentrations between 1 - 5 ppm, 20 g/l C1- and pH 5, the kinetics of loading on weak base resins are slightly slower than those observed with activated charcoal. Equilibrium loading of auric chloride varies considerably as a function of pH from one resin to another. For all of the resins studied, nearly complete gold extraction was achieved between pH 2 and pH 6.5. Sodium hypochlorite was found to exhibit a slight effect on the equilibrium loading of gold chloride.

Jan 1, 1990

By M. G. Hester, G. S. Adisoma

To address the problem of grade estimation in a general three-dimensional shape and the uncertainty associated with the estimate, the technique of jackknifing/ block-kriging shortcut is proposed. A new estimator called jackknife kriging is introduced first. Through the jackknife variance, a confidence limit for the reserve-grade estimate can be calculated. Unlike the kriging variance, which is more a measure of data configuration and which is independent of data values, the jackknife variance reflects the true variability of the data. This approach provides a simple way to set a confidence level for global estimation of resources.

Jan 1, 1997

By C. J. Gauvin

The Geological Department, headed by the Chief Geologist, is part of the General Engineering Division and is under the direct supervision of the Chief Engineer. The Geological Department is responsible for the technical direction of all work concerned with the finding and outlining of ore. It provides the mine operating staffs, with the necessary plans and sections to enable them to design pit and underground layouts and to, extract ores' as required by outgoing cargoes. The department maintains grade and ore reserve statistics in conjunction with a mining recovery factor at year-end. These duties are performed through the co-operation of all departments participating in the overall operation. As a result, a steadily broadening use is being made of geology at Steep Rock.

Jan 1, 1960

By William E. Mead

The process of selecting a building site for a major structure is a complex procedure involving the consideration of a multitude of factors. The approximate geographic location for a structure is usually fixed by its intended function, though often there may be several site alternatives. Socio-economic, logistic, marketing and political factors are the primary site determinants. Also critical in site planning, however, are the environmental factors, both natural and man-made. These factors will influence the precise siting location within the limits allowed by the primary determinants and will dictate some of the basic design criteria. This paper discusses environmental factors, principally those which are natural conditions, that must be analyzed for five different groups of structures. The importance of thorough site environmental analysis based upon the principles of applied earth science is described. Significant elements to be considered in an appraisal of the geology, hydrology, seismology and meteorology are outlined.

Jan 1, 1968

By B. S. Treiber, R. A. Lohnes, S. M. Levorson

As part of a research program to develop a coal-handleability index that would predict the ease with which a coal would flow through a handling system, an apparatus was developed to directly measure the unconfined Yield strength and bulk density of consolidated-coal samples. The new test apparatus provides a fast and simple method for determining the strength and compressibility parameters that are associated with the handling characteristics of crushed coal. Comparative tests were conducted using a low-stress triaxial-test apparatus. To check the accuracy of the new method, four coals with a variety of moisture contents and gradations were tested using the new method. These tests indicate that the new test device yields valid results. Further, the speed and ease of operation of the new device makes it suitable for quality control and quality assurance in plants.

Jan 1, 1996