Search Documents

By B. J. Arnold, B. W. Parker

Rosebud Mining Company added a classifying cyclone/spiral concentrator circuit addition to its McVille Preparation Plant, Freeport, PA, in mid-2002. This paper will describe the plant addition, which was implemented fully by plant staff, and review improvements in cleaning plant performance and economics.

Jan 1, 2003

By Robert F. Kaufmann

INTRODUCTION In response to the Uranium Mill Tailings Radiation Control Act (Public Law 95-604, Section 114c), a report has been prepared by the U.S. Environmental Protection Agency (1980) which describes the potential health and environmental effects associated with uranium mine wastes. The author was responsible for the geology, hydrology and aqueous pathways analysis portions of the report. All potential sources of contaminants, solids, liquids, and airborne emissions, which might cause adverse impacts upon the environment or health of nearby populations were considered. Wastes at both active and inactive uranium mines (Hans and O'Connell, 1981) are described and assessed with respect to dose and health effects (Blanchard et al. 1981). The emphasis of this paper is on the liquid emissions and the aqueous pathway. Model uranium mines were developed for surface and underground mines. The model underground mine was placed in New Mexico while the model surface mine was in Wyoming. Development of a generic assessment was complicated due to the inherent variability of uranium mines. Also, most information available relates to uranium mills rather than to mines, or reported measurements were often influenced (biased) by wastes from a nearby mill and did not specifically reflect mine discharges. Consequently, the assessment presented is often based on conservatve (maximizing) assumptions which are identified as such, and which were based on knowledge from field investigations, available literature, and consultations inside and outside the U.S. Environmental Protection Agency. Maximum use was made of available data, supplemented with limited field studies in Colorado, Texas, New Mexico, and Wyoming. PREVIOUS INVESTIGATIONS Stream survey work in Colorado by the Water Pollution Control Commission and the U.S. Geological Survey (Moran, 1974; Wentz, 1974) mentioned a portion of the Uravan Mineral Belt and uranium mines therein, but the work did not emphasize uranium mines. Significant amounts of acidity and total trace metal concentrations were found in streams from 18 different mining areas. Dilution and chemical precipitation below mine drainages decreased concentration and increased the pH. Given enough time and distance, the streams recover naturally, but the accumulations of trace metals in the sediments increase. Field observations in 1971-72 of streams in most of Colorado indicated that approximately 724 km of streams in 25 different mining areas were adversely affected by mine drainage (Wentz, 1974). Discussions of the impacts of uranium mining on water quality or quantity are incidental in numerous impact statements and environmental reports prepared by industry and (or) the U.S. Nuclear Regulatory Commission as an integral part of licensing or relicensing uranium mills. Coverage on mining is usually minor as the principal focus is on milling impacts. The same is true for the recently prepared generic EIS on regulation of uranium milling (U.S. Nuclear Regulatory Commission, 1979). Radiochemical assessment of surface and groundwater in uranium mining districts of New Mexico is done by self-monitoring programs associated with NPDES permits. Also, radiochemical assessment studies have been funded by the New Mexico Environmental Improvement Division and U.S. Environmental Protection Agency. Unfortunately, there has been no concerted effort to prepare broad assessments of the cumulative impacts of mining and milling in areas of interest in Texas, New Mexico, and Wyoming. Critical review and synthesis of these types of data can produce rather useful information. For example, the publication "Water Quality Impacts of Uranium Mining and Milling Activities in the Grants Mineral Belt, New Mexico" (U.S. Environmental Protection Agency, 1975) addresses the groundwater and surface water changes as the result of extensive uranium mining and milling production in a relatively confined area. A more recent report by the Wyoming Department of Environmental Quality summarizes 16 years of aqueous radium and uranium data. The study reports significant amounts of radium-226 and uranium were present in surface water in the Shirley Basin as a result of inadequate mine water treatment (Harp, 1978). In Texas, surface water and groundwater monitoring conducted by industry, as well as by State and Federal agencies, reveals little or no change of chemical quality attributable to uranium mining and milling (Gesell, 1977; Kallus, 1976). This conclusion is based on 586 samples collected from 198 stations over a period of 39 years, but primarily from 1961 to 1975. The State monitoring program by several agencies is continuing, but data reporting and interpretation is lagging. One survey (Itin, 1975) showed that none of the mine water from the 10 lakes that were sampled was suitable for human use. The lakes were also unsuitable for irrigation due to mineralization of the water by sulfate, chloride, and TDS. One of the 10 was suitable for stock watering.

Jan 1, 1981

By John E. Bailey

The advent of Nuclear Energy has caused a phenomenal growth in the uranium mining industry. To keep abreast of this surge the mining industry has located many ore bodies, determined the best types of mining adaptable to this particular type of ore and developed a highly specialized type of operation. But, has the mining industry gone far enough in the planning? Has ?built-in? safety been included in the efficient methods of operation? Preplanning safety in the mining industry, as in all industries, takes engineering and ingenuity combined with the experience and cooperation of all concerned. A system of mining can be planned on a map and it will look good. However, when the actual mining takes place, conditions may be such that deviations from the original plans may be required because of excessive water faults or other conditions encountered. With safety we may also be required to change, to conform to the characteristics of a particular operation. People in the mining industry are well aware that loose back has killed miners each year. This condition occurred in practically all types of mines. The condition is not new to us. It is also known that explosives, haulage, machinery and conditions common to all types of mining have taken a heavy toll of human life in mining. In addition to these hazards in the uranium mines, the hazard of radon is also present, Radon is a radioactive gas liberated from ores containing radium. This gas is released into the active workings by the blasting or breaking up of the ore. Sometimes it is caused by radium contaminated water seepage from abandoned workings or from the ore body itself. Until the action of this gas on the human was known, many miners were affected. Un- less adequate precuations are taken to protect the people in these mines,, they may be exposed to this hazard, Health researchers made a study of this substance to determine how it would affect the health of the men, They also studied men who had worked in previous years, in mines known to have contained radioactive materials. All of this research contributed to the present knowledge of radon and its daughter products. It is not flammable nor explosive, but, if allowed to enter the body through the respiratory organs it can cause serious damage. Mines have been operated in the past and are still being operated, which were known to contain explosive and noxious gases, indicating that this problem can be controlled. Several states have instituted laws that make it mandatory to provide adequate ventilation and use of monitoring devices to limit radon and its daughter products to a maximum of 300 micro-microcuries per liter of air. This is considered a safe limit for sustained periods of human exposure. While the findings of research do not prove conclusively that the inhalation of excessive radon or its daugher products cause lung cancer, indications point to this as a possibility, particularly radium A and radium C1 of the daughter products. The threshold limits set by law in most uranium producing states are believed to be safe. In a few years, when tests and data now in the process of collection by interested state officials and laboratories is complete, these limits may be found to be ready for revision. Studies such as these take time. At present, the limits that are used are based upon estimates. The permissible limits of exposure to radon and daughter products include a large safety factor. It is considered that a good supply of fresh air delivered to the working places, adequate dust control, the sealing of unused or abandoned workings, the removal of mine water which is generally contaminated and a safe waiting period after blasting, will hold to a minimum the dangers from this source. There are, of course, problems accompanying each of these procedures. For example, the ventilating of untimbered raises and bringing fresh, uncontaminated air to the working places may be a problem. However, a good mining man can solve these problems as they apply in each particular operation. From the information available at the present time, the daughter products containing polonium and emitting alpha radiation, may be a health hazard. Fortunately, the half life of most of the daughter products is short, however, radium D has a half life of 22 years and presents a problem of contamination in the storage of old tailings. So we can see that failure to comply with the accepted good mining practices may have harmful effects on the health of miners. It is gratifying to note the interest in this potential hazard by the officials in the uranium ore producing states, who are making extensive studies and keeping records of the men who work in this type of mining. This all provide information necessary for preplanning safety. By contrast, little has been accomplished to control the injuries and deaths from some other factors connected with most underground mining operations. I would like to discuss briefly one of the hazards which take an annual toll in our underground mines, this is falls of back and walls. This problem or hazard is present, and will be

Jan 1, 1958

By Jon P. Stone

The Automated Minerals Information System (AMIS) is an integrated data base system being developed to support the Bureau of Mines minerals information collection and analysis activities. The system facilitates cross-referencing and integration of domestic and foreign information from a variety of sources. The AMIS provides a central source of minerals information that is versatile and responsive to the needs of problem and policy analysts as well as supporting the needs of those involved in data collection and interpretation. As the AMIS becomes fully implemented, it will become an important tool in forecasting and assessing the impact of policy decisions that affect the supply and demand for minerals. The Bureau of Mines has long been the Federal Government's principal source of worldwide information on non-fuel minerals. Emphasis is placed on the analysis of mineral problems and policies as they affect the world's nonfuel mineral resources. To facilitate timely and accurate analysis, comprehensive data on 87 commodities are collected by various Bureau programs. Minerals information is made available through a number of periodic publications including the annual Minerals Yearbook and monthly Mineral Industry Surveys. These data collection and analysis activities have traditionally been supported by over 200 separate information processing systems. The Bureau of Mines has begun to implement a broad information strategy to provide a better response to the mineral problems and issues of the 1980's. The cornerstone of the Bureau of Mines information strategy is the development of the Automated Minerals Information System. When fully operational, we believe that the AMIS will provide the Bureau of Mines with the most comprehensive source of minerals information available anywhere in the world.

Jan 1, 1982

By William R. Taylor

The information I have concerning the early in situ uranium mining activities in Texas is "sketchy." Apparently, the first test was conducted between 1967 and 1971 in Gonzales County, north of Yorktown, at the Dueterstat Site, by, City Service. Other tests were run in Webb County at the Bruni Site, and in Live Oak County at the Burns and Clay-West Sites in the early 1970's. During this period the Texas Water Quality Board maintained a general surveillance of these tests. In mid-1974, Mr. Glen Davis walked into our Austin offices and requested a permit for Atlantic Richfield's first in situ uranium mine. This permit, issued in January, 1975, was for 3 acres of production, and was the first such permit issued in the United States. It formalized the regulation of in-situ uranium mining in Texas. The 4 years since then have been characterized by growth and change. Today there are 20 permits approved for approximately 2,000 production acres. These permits are issued to 8 companies at 13 sites in 6 counties. There are 7 additional permits being processed, or on the verge of being applied for. These will involve possibly another 2,000 production acres, 3 more companies in one more county.

Jan 1, 1979

By C. T. Thompson

"Rotary percussion" implies two types of energy, rotary and percussion. Into these categories fall rock' drills of varying sizes. The larger ones drill above 6" diameter holes; the medium size, 2 3/4" to 4 1/2" holes; and the smallest, 1 1/4" to 2" holes. Essentially, the larger holes are drilled with doom-the-hole drills using tri-cone bits. Percussion energy evolves from the drill piston and rotation power from the rotary table or overhead drive, using drill collars or pull down mechanism to preload the bit.

Jan 1, 1963

By S. K. Kawatra, Harrison R. Cooper

In the last 30 years, on-¬stream slurry analyzers have proven to be of great use in the control of mineral processing circuits. This review discusses the two most popular methods, x-ray fluorescence and neutron activation analysis, and also considers techniques which are still under development.

Jan 1, 1986

By D. Hong, K. N. Han

The leaching behavior of rhenium in ammonium iodide solutions with iodine as oxidant was studied. Experiments were carried out in an autoclave to investigate the effects of stirring speed, temperature, solution pH, and iodine and iodide concentrations on the dissolution of rhenium. It was found that a high temperature and a high solution pH were essential for the efficient leaching of rhenium. The dissolution rate was found to be dependent upon the concentration of iodine and iodide. It was concluded that the dissolution of rhenium under the conditions studied was controlled by the mass transfer of iodine with an apparent activation energy of 15.8 kJ/mole.

Jan 1, 1999

By J. A. Finch

The use of pneumatic methods for measuring interface level in flotation columns is analysed. It is shown that errors can vary over a wide range (e.g. 40 cm. in one industrial application) depending on bubble size, particle size, bubble loading, liquid hold-up and bulk slurry density. Accurate measurements (+ 5 cm) can be obtained by measuring intensive properties of the froth near the interface. Methods based on the measurement of temperature and conductivity are described and analysed. Control of the interface level using these measurements subject to various disturbances is demonstrated.

Jan 1, 1988

By Charles G. Frush

The function of the mine surveyor is to (a) provide a network of points of accurately known position, covering the entire mine property, (b) obtain the required data for the preparation of useful maps and sections! (c) provide position and directional control for the guidance of the operations, (d) measure the progress of the work, (e) measure the movement of rock masses, and (f) make miscellaneous surveys as needed. Mining properties range from the very small to the extremely large, and from those which involve only surface operations to those involving extensive underground workings. Active mines undergo constant change, necessitating continual updating of the surveys. The differences in the character of the deposits, the scale of mining and the mining methods result in large differences in the surveyor's activities and techniques, but many of the problems involved are common to most mines. The surface work of the mine surveyor is very similar to that, of the plane surveyor in that control points are established by triangulation, trilateration and traversing. Detail is taken by direct measurement, by stadia and by aerial photography. The equipment used, the techniques and the methods of processing the resulting data are likewise very similar. However, the underground work is quite different : A. The lines of sight frequently must be carried through constricted openings, often involving short lines of sight and awkward setups. B. The lighting often is poor, requiring illumination of the backsights and foresights, and the crosshairs. C. The ambient conditions often are difficult, involving falling water, high tem- peratures, poor visibi 'kv and heavy traffic through the area being suneyed. D. The surrounding rock map be unstable, resulting in movement or loss of the surveying stations, as well as hazard to the surveyors. E. The points to be measured often are difficult or impossible to reach. F. Steep vertical sights often are necessary, requiring the use of special equipment. G. Many working levels commonly are involved, requiring the transfer of position and orientation to each with a high level of precision. This section therefore will concentrate on surveying problems peculiar to the mine surveyor, chiefly underground work. 22.1-THE MINE COORDINATE SYSTEM A system of coordinates is essential for all permanent mining operations It is very desirable that all mining operations in a ,given area b~ tied into the same system, as this minimizes problems of boundaries and connections Whenever possible this system should be tied into and made part of the state or regional grid system. It is desirable to orient the coordinate grid on a true-north line and to position the origin of the coordinates so that all of the work will be in the "northeast" quadrant, making the north and east coordinates always positive. This can be done by subtracting suitable constant values from the north and east coordinates of the regional system The residual values are of more convenient magnitude and can be used as the local mine coordinates. If the long axis of the mineralization is not generally north-south or east-west.

Jan 1, 1973

By Jan Leja

Surfaces of metal sulfides react readily with selected constituents of environment. Two types of reaction products may form: (1) primary, chemisorbed and hydrophobic surface products or primary hydrophilic surface products, and (2) secondary reaction products -- produced during continued oxidation-reduction processes. For flotation, the chemisorbed surface product and the secondary reaction products, elemental sulfur or metal xanthates, must provide sufficient hydrophobicity of the surface to ensure particle-bubble attachment.

Jan 1, 1986

By J. W. Merks

Spreadsheet software is an effective tool for simulating dynamic stochastic systems such as mineral processing plants. The two-product formula is used to show how to set up a Monte Carlo simulation in a spreadsheet template and how to calculate variances of dependent variables. The key to a reliable and realistic simulation model is to obtain unbiased estimates for all independent variables and variances in the set that defines the stochastic system. Monte Carlo simulation is also a powerful tool for optimizing sampling procedures, for applying sensitivity analysis and for designing and evaluating experiments.

Jan 1, 2000

By James W. Griffith, Sarah A. Riling

Bituminous coal dust was repeatedly placed into one lung lobe of anesthetized Macaca nemestrina monkeys using a flexible fiberoptic bronchoscope. Radiographs taken at 15 day intervals showed a focal radiographic density after 90 days time when a total of 1 gram of dust had been instilled. The radiographic density progressed slightly in size until 12 months by which time 3 grams of dust had been instilled and the animals were euthanized. At necropsy, the only significant gross lesion detected was the focal black pulmonary lesion located at the dust instillation site. Histologically, the lesion was composed of coal dust laden macrophages located primarily within interstitial tissue and interspersed with a slight amount of reticulum and connective tissue fibers. The distribution of coal dust was limited to the instillation site in the right caudal lung lobe based on radiographic, gross and histologic examination. Bronchoalveolar lavage of both right and left caudal lung lobes was performed 8 times during the 12 month long experiments without significant complications. More macrophages were found in lavage fluid from the right lung than the left, and most macrophages from right lung contained coal dust particles. Based upon a limited physical examination and complete blood count at 15 day intervals the animals remained normal during the experiment. We conclude that the primate lung's response to focal experimental bituminous coal dust resulted in a marked focal increase in pulmonary alveolar macrophages, which can be recovered regularly in high numbers by bronchoalveolar lavage. The model described has significant potential for investigating the pathogenesis of various respirable dust-induced pneumoconioses, for evaluation of new therapeutic approaches, and for refining experimental and clinical diagnostic applications of bronchoalveolar lavage. Key words: Coal Workers Pneumoconiosis, Disease model; Primate, Lung Lavage Fluids

Jan 1, 1991

By Guy T. Jr. McBride

World food production is not matching the exploding increase in world-population. Since arable land is limited, ways are being sought to increase yields by turning_ to fertilizer. Phosphate, an essential fertilizer ingredient, is undergoing a period of growth unparalleled in history. The United States is at once the world's largest producer of food and of phosphate rock. Both food and fertilizer output in the United States are being enlarged to meet the demands posed by the threatening world food crisis. New phosphate deposits are being developed in Florida and North Carolina to assure the United States' continued preeminence in this vital resource. Large fertilizer complexes are also being constructed with an eye to both domestic and foreign markets. The growth of the U. S. phosphate industry has been characterized by developing technology in the processing and distribution of phosphate raw materials. The trend from low analysis to high analysis materials accompanied by a change from a large number of small fertilizer plants oriented toward the marketplace to a fewer number of large plants located at the raw material source is illustrative. These changes in technology and distribution have also been important factors in the development of new mining areas in Florida, the Western States and North Carolina.

Jan 1, 1966

By L. E. Krys, K. D. Harrison, C. G. Anderson

Since 1984, nitrogen-species catalyzed pressure leaching has been utilized at Sunshine Mining and Refining Company for the recovery of precious metals from a refractory sulfide concentrate. The process operates without the use of cyanide. The plant is now the only industrial-scale commercial application of this technology. Since the inception of the process, changes have been implemented to improve efficiencies and throughputs. Two of these changes, the replacement of nitric acid by sodium nitrite and a concentrate regrind, have recently been implemented. This paper discusses the development and potential mechanisms involved in these recently patented plant-process changes. A companion publication (Anderson et al., 1996) covers the plant integration and potential applicability of the technology.

Jan 1, 1997

By Frederik P. Agterberg

During the past 20 years, methods of multivariate statistical analysis have been developed on mainframe computers for the integration of geological, geophysical, geochemical and LANDSAT data in mineral resource appraisal. At present, it is becoming increasingly feasible to perform mathematical image analysis of digitized patterns on microcomputers. This has led us to develop a new method of statistical pattern integration for mineral exploration. In this paper, the new method is used to outline, by means of posterior probabilities, exploration targets within small areas of which the prior probabilities for occurrence of new mineral deposits had been estimated by multivariate analysis.

Jan 1, 1989

By G. D. Criswell, F. Palkovits, J. M. Johnson

A paste technology investigation was completed for non-pozzolanic fly ash from Units 3 & 4 of PPL Montana’s Colstrip Steam Electric Station. The purpose was to assess the feasibility of converting from dilute slurry deposition of ash products to a system using thickened or paste ash to reduce excess water storage in the impoundment, reduce seepage losses, and increase storage efficiency. The investigation included laboratory and field testing to characterize the rheological, geotechnical and dewatering properties of the ash products, an assessment of potential seepage reductions and an evaluation of potential for increased ash storage capacity by modifying impoundment operating procedures. The studies concluded that the conversion project was feasible, cost effective, and permittable. Critical facilities for the conversion project are currently under construction.

Jan 1, 2004

By Estban M. Domic

The modem copper industry presents an excellent opportunity for the application of clean, environmentally friendly techniques using currently available hydrometallurgical technologies. This paper briefly reviews key events in the development of modern hydrometallurgy in Chile. Discussion is given to those prominent events whose impact continues to be felt on most projects currently underway. Mention is also made of the foundations of heap leaching technologies, preceded by agglomeration and acid curing, known as the T.L. Leaching Process, the cornerstone of more recent developments. A review is also presented of the leading copper hydrometallurgy projects of the 1990s. A list of those projects, their tonnages and the estimated date of implementation is provided. The conclusion provides an overview of developments in research and the trends in the implementation of copper hydrometallurgy projects in Chile for the coming years.

Jan 1, 1998

By Michael J. Hannan, Thomas F. Torries

The nature of industry structure is examined and the structure of the aluminum, copper, lead and zinc industries are described by the use of factor analysis. Capacity is defined and the relationship between industry structure and capacity utilization is examined. It is demonstrated that excess capacity is possible in industries with competitive or monopolistic characteristics, but the effects of the overcapacity are vastly different in the two cases. In a competitive industry, cycles of overcapacity with attendant fluctuating prices are expected. A change in industry structure from monopolistic to competitive characteristics over time causes profits and economic rents to be transferred from the producer to consumers of the mineral.

Jan 1, 1989

By A. J. Monhemius, S. Raghavan, G. W. Warren, E. Peters, D. W. Furerstenau

A lyometallurgical process for extracting copper from an ore containing chrysocolla by leaching it with a kerosene solution containing LM 63 in the presence of small amounts of aqueous ammonia is described. The experimental results indicate that 70 to 75 percent of the copper can be extracted from the ore using an ammonia content that is about one-fourth the stoichiomeaic quantity required to leach copper in an aqueous leaching system. The rate of copper extraction was found to be a function of particle size, ammonia concentration and temperature. The large quantity of physically adsorbed water together with ammonia in the pores of chrysocolla provides a mechanism for the transport of copper to the external surface of the particles where it is complexed by the LM molecules and transferred into the organic phase. When size reduction accompanies leaching, the extraction process was found to proceed when only "trace" quantities of ammonia are present in the system. The kinetics of the extraction process appear to be controlled by a mixed (reaction and diffusion) mechanism.

Jan 1, 1993