Search Documents

By J. D. Miller, J. Hupka

Environmental applications of the air-sparged hydrocyclone (ASH) technology are presented. The original ASH design used porous sintered steel or porous polyethylene tubes as spargers. To diminish/prevent plugging and to reduce pressure head loss in the gas path a wire screen sparger and new hydrocyclone design have been developed, which allows for wide application of the technology to solve environmental problems and to be used as a chemical reactor. Field and laboratory trials have shown that the ASH technology might be preferred for the stripping of volatile organic compounds WOC) from contaminated water. The ASH has also been developed for absorption of SO2, toluene vapors, and for the recovery of cyanide.

Jan 1, 2005

By Stéphane Servant, Jacques Ouellet, Ferri Hassani

This paper presents essentially the logistic and practical aspects involved for in situ testing of mine paste backfill with a self-boring pressuremeter. The investigation discussed in this paper is part of an extensive and ongoing research project to identify and validate an in situ testing technique for cemented mine backfill such as hydraulic or paste backfill as well as Insitu behavior of backfilled stopes. After a literature review on field testing of soils and past experiments on mine backfill in situ testing, the self-boring pressuremeter was selected as the most appropriate instrument for this task. The authors presents in this paper the technical aspect involved in a field trials that was conducted in a Canadian underground mine using paste backfill. The results of this first successful trials show that self-boring pressuremeter test can provide high quality and reliable backfill characteristics results, using analytical techniques developed for soils (Ouellet et al., 1998). The parameters obtained were: estimation of the lateral stress in the ground, the soil stress-strain response and the soil strength. The logistic and equipment required to conduct such testing underground is fully described. Performance achieved in the field and technical difficulties encountered are highlighted. Recommendations for future experiments with such instruments are given. Some potential technical improvements to better adapt this in situ testing technique to mine backfill are proposed.

Jan 1, 2001

By G. Pan

A geostatistical approach is proposed for the design of infill drilling programs. The method consists of the following four major steps: developing geological favorability models, delineating mineralization and ore envelopes, classifying resource potentials, and designing infill drilling patterns. Geological modeling develops the permissible geological zones in which infill drilling is designed. Modeling mineralization and ore envelopes establishes criteria on the potential blocks to be drilled. The blocks that are included within the ore envelopes are considered in the infill drilling. The following four types of resource potentials are used in this analysis: measured, indicated, possible and barren. Blocks in the indicated category are the top targets to be confirmed in infill drilling. Blocks of possible resources may be considered exploration targets. The algorithms involved in the analysis include indicator favorability analysis, indicator kriging and ordinary kriging. A case study on a gold deposit of the Carlin type is presented to demonstrate the methodology. The deposit was originally delineated by a sparse drilling program with about 230ft of average spacing. The infill drilling design, based on the new method, suggests a significant reduction on the number of holes from a regular-grid infill drilling pattern.

Jan 1, 1996

By W. G. Pariseau

Regression analysis of calculated on measured displacements were used to assess the influence of fill and fold plunge on shaft pillar mining at the Homestake Mine. These effects were neglected in the original three-dimensional finite element analysis undertaken in 1991. An average fold plunge of 15? and a 24K fill (Young’ modulus of 24,000 psi or 165 Mpa) were used in the reanalysis. Measured displacements were obtained from an array of 36 m (120 ft) multiple-position borehole extensometers installed in June 1994 and read to March 2003. Results indicate the effects of both on calculated displacements and thus on regression parameters are noticeable. However, these neglected effects would not have changed the original inference of Ross Shaft stability during pillar mining.

Jan 1, 2004

By Carlon C. Chambers

INTRODUCTION Manufacturer sponsored research over the past three years has proven the suitability of styrene-butadiene/ asphalt membranes in many waste disposal seepage control applications for the mining industry in general and uranium mining and milling in particular. The class of membranes that have been tested are SBR/asphalt blends containing up to 68 weight percent asphalt, the balance being elastomeric polymers, fillers and phase compatibility promoters. These membranes are classified as thermoplastic, elastomeric materials and can be hot spray applied to any moderately dry substrate at 177°C (350°F), and placed in service within one hour of application. The properties of this membrane that make it suitable for use as an engineering_ material in these applications are discussed. These properties include chemical resistance, bacterial resistance, UV light resistance, permeability, stress/strain characteristics and bonding data. The favorable economics of the system are also discussed. The preliminary raw test data on the above properties were reported in a previous paper, (Chambers, 1980) and most will not be repeated here. Instead, this report considers the original data in relation to subsequent data and concentrates on interpretation of the trends for engineering purposes. However, several of the pictures contained in the original paper are reproduced in this report for illustration purposes. BACKGROUND Asphalt alone has a long history of use as a water-stop material. Its limitations of becoming brittle when cold and soft when hot, however, are well recognized. The service temperature for common grades of asphalt is usually in the 4° to 49°C (40° to 120° F) range. Modifications to the base asphalt can generally improve its performance at the high end of the temperature range by raising its softening point, but only the addition of one class of modifiers, elastomeric polymers, improves low temperature flexibility as well and also adds resilience. Both of these properties are of extreme importance if the waterstop material is to maintain its integrity when used on substrates which are unstable, non-cohesive, discontinuous or have significant expansion/constraction coefficients. Although there are many elastomeric polymers which can be used with

Jan 1, 1980

By D. R. Babich, E. R. Bauer

Noise induced hearing loss (NIHL) continues to be a problem in the mining industry. New noise standards (Part 62) promulgated by the Mine Safety and Health Administration (MSHA) are aimed at reducing NIHL in the mining industry. The National Institute for Occupational Safety and Health (NIOSH) is conducting a cross-sectional survey of noise sources and worker noise exposures to address NIHL in mining. Noise surveys, including full-shift worker noise exposure and equipment noise profiling, have been completed in several surface coal mines, with an emphasis on draglines. The results of these studies are reported, their implications concerning worker NIHL are addressed, and their application to administrative and engineering controls is discussed.

Jan 1, 2003

By Thomas D. Kaufmann, Robert C. Drury

Few factors are as important as fluctuations in aggregate economic activity and exchange rates in determining the profitability of mineral investments. Macroeconamic theory explains how the two factors are interconnected in today's world and in tomorrow's. We can use macro¬economic theory to lessen some of the risks in mineral investments. And in the current state of the world the risks are high. The above paragraph summarizes our argument. Our goal in this paper is to examine the nature of contemporary business cycles so as to explain their implications for the metal industries, particularly the implications for capacity. Thus, our first section examines the workings, causes, and history of the recent economic fluc¬tuations. In doing so we must understand how current world economy is interconnected, that is, how economic events in one country are trans¬mitted to the rest of the world. Our view is that governments and central banks are key actors in the creating of economic fluctuations. Then, in section two, we work out the implications of section one for the metal industries focussing on comparative advantage, trade, and capacity decisions. Over the last fifteen years the world economic system has had slow overall economic growth and has had strangely unpleasant recessions. While future business cycle will not repeat the de¬tailed pattern we have seen, there will be similarities. The similarities need to be under¬stood before investment occurs. The slow growth in the world economy since the early 1970s has aggravated the problems from business cycles, created its own problems, and has partially hidden the effects of other events. Major realignments of currencies are likely to take place over a business cycle. The nature of the causes of the cycle will determine the direc¬tion of change in the exchange rates. For example, whether a USA recession will be accompanied by a weaker or a stronger dollar will be determined by the cause of the recession. The realignment of currencies over a business cycle leads to a realignment of comparative advantage in the metal industries. Thus, not only will world metal consumption vary over the business cycle but the impact on various countries' metals industries will differ consi¬derably. Competitiveness often depends more on the value of the dollar than it does on inherent efficiency and wage rates. Capacity decisions are inherently riskier due to the country specific nature of exchange rate risk. A realignment of currencies changes the pattern of trade if and only if the country with the cheaper currency also has idle capacity. The importance of our topic is indicated by Table 1 which shows the impact of cyclical and exchange rate shocks on the USA metal industry. In the cyclical downturn, from the peak of 1979 to the trough of 1982, consumption dropped by a fifth to a third. Metal price moved in the same

Jan 1, 1989

By Alice S. Allen, James Paone

SURFACE SUBSIDENCE IN MINING The consequences of subsidence are becoming progressively more serious as the consumption of an ever- increasing quantity of minerals conflicts with the needs of an expanding population for surface land area. The inevitable result will be an increase in the amount of land area on which undermining is restricted because surface subsidence must be prevented. Designation of land areas that may be undermined, provided that subsidence is controlled and kept within specified limits, also will increase. The decisions as to which land is to be used for urban, agricultural, or other purposes clearly involve considerations that go far beyond the scope of mining technology. Under the authority assigned to the US Bureau of Mines (USBM) by the Organic Act (May 16, 1910) and its succeeding amendments and pursuant regulations (30 U.S.C. 1-1 1 ), the Bureau conducts scientific and technologic investigations concerning mining and its related problems. Subsidence-control demonstrations that have been conducted under this authority include projects in Wyoming, West Virginia, Illinois, and the Pennsylvania anthracite region. The problenls for technology arc to devise methods for extracting minerals with controlled subsidence in varying geologic settings and for calculating or predicting the amount, extent, and characteristics of the subsidence that accompanies the extraction of our principal minerals mined by high-tonnage methods so that logical choices can be made from the possible alternative approaches. Where underground minerals and fuels are mined and removed, the voids that are created underground generate strong imbalanced stresses in the surrounding and overlying rock strata. The resulting readjustments in the rock masses may cause subsidence of the ground surface. Subsidence implies vertical collapse, because the most conspicuous component of movement is downward. However, the downward component is accompanied by differential horizontal strains that may be more damaging to man-made surface structure.; than the more apparent vertical displacements. SUBSIDENCE CONTROL The most widespread method of alleviating potential subsidence problems in undermined areas has been to backfill mine voids with mine refuse or some other in- expensive material that provides lateral support to the remaining mine pillars and vertical support to the mine roof and overburden. Most USBM backfilling work has been conducted jointly with the Pennsylvania Department of Environmental Resources in the anthracite region of northeastern Pennsylvania. These joint projects were conducted under the authority of the Anthracite Mine Drainage Control Act of July 15, 1955 (Public Law 84-162, as amended), and the Appalachian Regional Development Act of 1965 (Public Law 89-4. as amended). In addition to the Appalachian and mine-drainage projects, the Bureau has either conducted or participated in demonstration projects to develop the "pumped- slurry" method of backfilling mine voids. Three of these projects were conducted in Rock Springs, WY. The first was a field test of the pumped-slurry technique, conducted in 1970 under the combined participation of the City of Rock Springs, the US Department of Housing and Urban Development, the Dowell Div. of the Dow Chemical Co., and USBM (Candeub, Fleissig, 1971). The objective was to demonstrate that a large quantity of sand could be hydraulically injected under pressure through a single borehole, and that filling of the mine voids would be essentially complete. In the earlier "blind-flushing" methods, involving sluicing material through boreholes by gravity, quantities per injection hole ranged from 15 to 765 m3 (20 to 1000 cu yd), and the mine voids were only partially filled. In the first test of the pumped-slurry method, approximately 14 900 m (19,500 cu yd) of sand were injected success- fully through a single borehole. Subsequent information obtained through 43 monitoring boreholes indicated that mine voids below 11 330 m2 (2.8 acres) had been filled. As a result of the successful initial test of the pumped-slurry process, USBM conducted additional backfilling demonstration projects using the new technique. The first full-scale demonstration was carried out in the Green Ridge section of Scranton, PA, between 1972 and 1974. This project proved the feasibility of using the new hydraulic-injection technique to back- fill dry mine voids, as well as flooded voids, and it demonstrated that crushed anthracite refuse could be used as easily as sand in the process. Stabilization was pro- vided for about 202 300 m2 (50 acres) of Scranton, having a population of approximately 1000. Additional demonstration projects at Rock Springs, WY, between 1973 and 1975, resulted in the stabilization of about 364 200 m2 (90 acres). The work was necessary to preserve the physical and economic well- being of the city, because there have been numerous occurrences of subsidence during recent years. A demonstration project completed in 1976 in Rock Springs brought the total stabilized area in that city to 647 500 m2 (160 acres). At a cost of about $3,000,000, a population estimated at 7000 persons and property values exceeding $18,000,000 were protected. Presently. USBM is participating in subsidence- control projects involving backfilling in Pennsylvania, Illinois, and West Virginia. Eleven demonstration projects were in progress by USBM in 1977-eight in the Pennsylvania anthracite region and three in bituminous areas of West Virginia (one) and Illinois (two). The estimated total property value is over $100,500,000, and the total cost of the projects is expected to be nearly $20,000,000. The demonstration projects are designed to adapt the pumped-slurry technique to a variety of subsurface conditions, to increase efficiency, and to reduce costs.

Jan 1, 1982

By Yanmin Wang, Eric Forssberg

This paper presents recent experimental results in wet ultra-fine grinding and classification of industrial minerals carbonates and kaolin clays using a stirred ball mill and a high performance centrifuge. The studies have been focused on the effect of beads (size, density and load) on the grinding efficiency. The use of chemical additives for the control of slurry rheology in the stirred ball milling is presented. The role of pre-crushing with a high-pressure roller mill on subsequent ultra-fine grinding is discussed for energy saving and size reduction. The use of a disc-stack nozzle centrifuge for ultra-fine classification duties at high solids contents is presented.

Jan 1, 1998

By V. W. Skema, M. W. Smith

Pennsylvania has 4,000 km (2,500 miles) of streams that do not meet water-quality standards due to acid mine drainage (AMD), making AMD the greatest cause of water pollution in the state. The problem is mainly caused by abandoned coal mines. To abate AMD, Pennsylvania is using a watershed-based approach that includes remining as a key component of a comprehensive restoration strategy. The Tangascootack Creek Water-shed was targeted for AMD restoration through remining. Geologic mapping and overburden data were analyzed using Earth Vision software to identify areas of coal reserves that could be remined to improve water quality. Incentives are offered to encourage mining in these designated areas.

Jan 1, 2002

By N. Dahotre, C. Blue, C. Zhao, B. Parekh, D. Tao, G. Engleman, R. Honaker

Equipment wear is one of the major concerns in screening of coal and minerals. Not only does it decrease the screen service life, it also results in inconsistent aperture sizes and deteriorates the efficiencies of downstream operations. In this research, a coating technique based on laser surface engineering (LSE) was successfully developed to increase the life span of raw coal screens. The microstructure and wear properties of the coating were investigated in this study. Enhanced wear resistance performance (up to 11-fold increase) of coated screens has been achieved in laboratory wear tests.

Jan 1, 2006

By Robert A. Jankowski, Ellsworth R. Spencer, Jay F. Colinet

Longwall mining is the most productive method of under- ground coal mining in the United States (US.), and record levels of production have been reached in recent years. These ever-improving production levels have the potential to generate significantly higher quantities of respirable dust. Consequently, the longwall industry continues to struggle with controlling dust liberation and maintaining compliance with the federally-mandated respirable dust standard. In response, longwall operators have in- creased the application of primary dust controls, airflow and water flow, in an effort to improve respirable dust control and reduce worker exposure. Pittsburgh Research Center (PRC) personnel conducted dust surveys at 13 longwalls operating throughout the U.S. and collected information to: identify current operating practices on these longwalls, identify the types of dust controls in use, document the levels at which these controls are being applied, and measure the respirable dust levels present. This data was analyzed to quantify the dust levels generated by the major sources on the longwall section and to evaluate the relative effectiveness of the control technologies in use.

Jan 1, 1997

By L. Vandamme, J. H. Curran

A fully three-dimensional hydraulic fracture propagation model, based on the Displacement Discontinuity Technique, is briefly described. Using this model, it is shown that the geometry of a propagating fracture is dependent on several factors, among which the fluid pressure distribution within the fracture plays an important role. The containment of hydraulic fractures is found to be dependent on stress and toughness barriers in the formation. Containment is also observed to be more effective with a decrease of the viscosity, pressure or flow rate of the injected fluid. The three-dimensional layout of the fracture is shown to have a definite influence on the width and pressure distributions within the fracture. The examples considered indicate the need for fully three-dimensional models, as complements to the commonly used two-dimensional and pseudo-three-dimensional models.

Jan 1, 1986

By R. R. Oder

Reported are weight, particle size, gross chemistry and magnetism measurements for lithic, mineral and fused soil components separated from five lunar soils using dry, open-gradient, magnetic separation. Pure diamagnetic anorthite, a feedstock for the electrochemical separation of oxygen and metals, has been separated from anorthistic highland soils. In addition, paramagnetic ilmenite has been separated from high-titanium, basaltic mare soils. Ilmenite, a feedstock for oxygen preparation by hydrogen reduction, may also serve as a source of He3 for use in fusion power generation. Agglutinates (vesicular, glassy components containing metallic iron) have been separated from all of the soils. Iron and refractories can be used for space construction. Metallic iron is easily detected in lunar soils by magnetic susceptibility measurements. Based on the exploratory laboratory results, conceptualizations of innovative magnets for processing lunar soils are presented.

Jan 1, 1993

By L. A. Taylor, R. O. Colson, D. S. McKay

The production of oxygen on the Moon utilizing indigenous materials will be essential for successful lunar colonization. Several processes have been put forth to accomplish Lunar Liquid Oxygen (LLOX) generation. The schemes that have received the most study to date involve: 1) Reduction of ilmenite (FeTi03) by H2, CO, CH4, CO-Cl2 and Cl2, plasma. 2) Molten silicate electrolysis, both unadulterated and fluoride fluxed. 3) Several others, including H, reduction of glass, carbo-chlorination, HF acid leaching, fluorine extraction, magma oxidation, and vapor pyrolysis. The H2 reduction of ilmenite and molten silicate electrolysis processes have received the most study to date. They are both feasible schemes and have various pros and cons, including their feedstock requirements. However, all processes should be addressed at the onset of LLOX research. This paper reviews several of the most studied and feasible processes for winning oxygen front lunar materials. There is an obvious need for more experimentation and study.

Jan 1, 1994

By Donald L. King, Frank A. Baczek

Sedimentation-based equipment is used in applications where separation of solids from liquid by gravity settling is desired. If a concentrated solids slurry is desired, the equipment is designed to "thicken"; if a clear liquid is desired the equipment is designed to "clarify." Thickeners normally handle higher solids loading rates than clarifiers, which usually process feed slurries containing low concentrations of suspended solids. Thickeners are therefore designed for heavier-duty requirements, and clarifiers have extra features to ensure more complete suspended solids removal. Major components (Figure 1) that are common to all sedimentation-based equipment are: tank, drive-support structure, drive unit and lifting device, rake structure, feed well, and a means of overflow and underflow withdrawal. Specific features are designed interdependently after the overall separation approach is defined conceptually. This conceptual approach is usually based on past experience or evolves from sedimentation studies conducted on samples of the slurry to be handled. Because many variations and combinations of components are possible, the overall conceptual approach has a number of possible designs that will accomplish the desired results. The final choice is based on practicality, potential for minimizing upsets, and cost.

Jan 1, 1986

By Wayne A. McCurdy

I welcome the opportunity to meet with you and discuss the work and program of the Office of Coal Research. Our programs are oriented to serve the conservation objectives of the Johnson Administration and of the Nation by seeking out the most efficient and best uses for coal. We believe that even if only a portion of our program is successful, the coal industry and the Nation will benefit far out of proportion to our expenditures. Operating with a budget of $7,220,000 in Fiscal Year 1966, OCR sponsors contract research which offers potential for achieving benefits to the coal industry in the form of new production and new markets. This directs us into many areas of research activity: in coal combustion, in advancements in mining methods and coal preparation, in new uses for coal, and in associated economic and marketing research.

Jan 1, 1966

By E Marambio, R Brändle, G Fischer, G von Rickenbach, M Fuentealba, L Burgos, R Luis Fonseca

In underground excavations, under high stress conditions, ground support systems must provide safe and effective response to dynamic events. These systems must be capable to resist dynamic impacts and yielding during the loading process. In this context dynamic testing of the reinforcement and retaining elements that compose the ground support system are required to study and improve the behaviour of these elements under dynamic load events. During the last years, Geobrugg has been working on the improvement of retaining products by testing them in a large-scale impact test facility located at Walenstadt, Switzerland. The test facility is composed of a double level platform with a square-shaped pyramidal trunk geometry, in the upper level housing a loading mass that drop from a height up to 5m. The loading mass is guided by one central steel pipe, and the impact occurs in the sample to be tested located at the lower level in a slab with an area of 3.6m × 3.6m where the ground support system is installed. During the last years, this innovative facility has been used to test several configurations of ground support systems. The results of these tests have enabled to improve the understating of the behaviour of ground support systems under dynamic loads. In this manuscript, the back analysis through numerical methods (central difference and Newmark’s method) of a ground support system tested with a double dynamic impact in 2019 is presented.

Apr 26, 2022

By Matthew Spedding

The complex nature of the carboniferous measures prevailing in the U.K. has dictated the types of mining required to exploit the coal seams. Most mines in Britain are referred to as deep mines in the sense that they operate at depths of 1800 - 3000 feet. The main system of coal transport to the surface is by vertical shafts which intersect the workable seams which at times number between 4 and 5. As mining has been practiced in most of the major coalfields in the U.K. for well over 100 years, with the initial extraction of the shallower and more profitable seams, the present management have been left a legacy of indiscriminate extraction which severely hampers their efforts to maximise the mine layouts. There is no single standard design of mining layout capable of meeting the wide variety of conditions which exist in the British coalfields. Mining layouts are subject to fixed and variable parameters. In discussing multi-seam working, the main parameter must be the effect of old workings above and below the seam to be extracted. There is a distinct lack of reliable information which would enable layouts to be designed to completely avoid or control these destructive forces. The guidelines are, therefore, mostly empirical.

Jan 1, 1977

By Keith E. Dyas, John Nelson, Ronald T. Johnson

GENERAL DESCRIPTION The Bruce mine of Cyprus Mines Corp. is located in Bagdad, AZ. The mining method used is open cut-and-fill. Of the annual production of 81 647 t (90,000 st), approximately 83% is taken from load-haul-dump (LHD) stopes and the balance from slusher stopes. All ore is produced from the area between the 1250 level and the 2300 level. The average travel time from the shaft pocket to the stope is approximately 5 min. GENERAL ORE BODY REQUIREMENTS AND LIMITATIONS Size, Shape, and Dip The Bruce ore body occurs in quartz-sericite schist with Dick rhyolite on the footwall and andesite on the hanging wall. Diabase dikes are found in the hanging wall; there is also a dike coming off the footwall and crosscutting the ore body. All of the rock types are of the Precambrian Yavapai series and have been subjected to regional metamorphism. A composite of the ore body is given in Fig. 1. The deposit is of massive sulfides occurring as a steeply dipping replacement body. On the upper levels the ore is veinlike with widths from 0.6 to 4.6 m (2 to 15 ft), dipping at 1.4 to 1.5 rad (80° to 85°). On the lower levels the ore is dipping from I to 1.2 rad (60° to 70°) with widths from 3 to 16.8 m (10 to 55 ft). The strike length varies between 107 to 183 m (350 to 600 ft). The rhyolite footwall generally has a knife-edge contact with the massive sulfides. The exceptions to this are the upper levels where there is a 1.5 to 3 m (5 to 10 ft) band of silicified sericite schist between the sulfides and the rhyolite. In the southern part of the ore body the hanging wall is tuffaceous andesite and andesite. In this area the contact is generally sharp and easy to follow. However, to the north there is a large chlorite schist zone that crosscuts the bedding and comes in contact with the massive sulfides. This is apparently due to hydrothermal alteration of the andesite. The chlorite schist is highly mineralized with chalcopyrite and pyrite and quite often forms economic pockets of ore. In the massive sulfides the chief ore minerals are sphalerite and chalcopyrite. Pyrite is the predominant sulfide with considerable pyrrhotite throughout. Bright arsenopyrite ouhedrons in fine grain massive sulfides are quite common. Occasionally small amounts of galena are seen, usually near the foot or hanging wall contacts. On rare occasions tennanite is associated with massive arsenopyrite. Minor amounts of quartz, calcite, and un¬replaced remnants of sericite schist occur, but essentially pyrite is the gangue in which the ore minerals occur. The ore values are in excess of 3.5% copper and 12.5% zinc with some silver and rare gold as byproducts. Ground Conditions The massive sulfides are generally self-supporting. One exception is in the 1850 stope where the ore body is 9 to 11 m (30 to 55 ft) wide and 152 m (500 ft) long. There are flat to shallow dipping slips and seams in the ore, creating extremely blocky ground. For support, old 25.4-mm (1-in.) hoist ropes were installed tensioned to 27 t (30 st), and then cement grouted over the entire length in longholes [14 to 15 in (40 to 50 ft) in length) drilled on 3-m (10-ft) centers from the level above. This has tied the formation together very successfully and virtually eliminated the blocky ground condition. Both the hanging wall and footwall are quite shaley in some areas. Reasons for Adopting Trackless Open Cut-and-Fill Methods First, any method other than open cut-and-fill would have caused too much dilution. The use of rubber-tired mining equipment in the pro¬duction stopes requires a footwall ramp. The inclines in ore will be mined out, so this ramp in the footwall will provide access to and from the stopes (Fig. 2). This incline is very expensive, but necessary to convert existing stopes to LHD mining. 'The final cost of ore mined by the LHD machines has not been determined. As of 1972, tons per manshift in the 2150 stope-the only one to complete a full cut-had increased from 7.58 t (8.36 st) to 12.83 t (14.14

Jan 1, 1982