Search Documents

By Carlos Kovacs-Figueroa

Because of air pollution control regulations in the early 701s it became necessary to clean effluent gases from the Morenci Reduction Works Smelter. Feasibility studies indicated that this could be accomplished most efficiently by using the smelter gaseous effluent to feed a sulfuric acid plant. Complying with air pollution control regulations thus created the need to dispose of relatively large amounts of concentrated sulfuric acid. Typical Morenci ores contain substantial amounts of oxidized copper minerals which are not recoverable by flotation. In addition, there is low sulfide, high oxide material which can be leached, but is not suitable for flotation concentration. Early in 1971 sufficent data had been accumulated to show that a leaching plant for the Morenci tailings could use a large portion of the sulfuric acid produced by the Smelter. It was determined that for all practical purposes leaching of the available copper was complete in two hours or less. Capital expenditures could not be justified for more than two stages of counter current decantation for recovery of the leached copper, and the plant was designed with these criteria in mind.

Jan 1, 1976

By Thomas Pea, Heiner Kontrus, Jérôme Steinkühler

In tunnel condition assessment, the trend is towards comprehensive 3D measurement combined with high quality image texture to document and quantify damages to the tunnel surface and to create a cohesive data base of the structural conditions throughout its lifespan. The faster such measurements can be made on site, the less it impacts traffic conditions of the highly sophisticated subway systems. The Dibit high-speed 3D scanning system which is based on Photogrammetry and LiDAR technology enables data acquisition in tunnels at a speed of up to 60 mph. Given the high rate of speed the system can operate, tunnel shutdowns can be drastically reduced, and tunnel safety increased. The photorealistic texturing of the 3D-model allows the identification and analysis of smallest material damage (e.g., cracks ≥0.3 mm wide). The publication illustrates technical details and 3D results of the innovative system from measurements that were performed in the subway tunnels of the Bay Area Rapid Transit System in San Francisco, CA (total length 66.23 km).

Jun 13, 2021

By Carlos Tarazaga

Progressive Design-Build (PDB) is an emerging variation of alternative delivery programs in the underground construction industry. PDB refers to the way a construction project design is developed by the Owner and the Design-Builder in a step-by-step process. According to the Design-Build Institute of America (DBIA), Progressive Design-Build allows the design and construction team to collaborate during the earliest stages of project development. This enables engagement between the three key players in a construction contract: the owner, the designer, and the contractor. Is the PDB the best alternative program delivery for large contracts? What is the perspective of the private sector? This paper will provide an overview of the different alternative delivery programs used in the underground industry, pros and cons of each of programs, and the perspective of the designers and contractors. The paper will focus on how the PDB works, reasons why owners should consider PDB for their projects, best collaboration strategies among owners, designers, and contractors to deliver a successful project, and how to manage the project risks using a PDB method.

Jun 13, 2023

By M. D. Loy

In addition to products available from private vendors, many useful programs are developed at universities - in fact, many of these programs led the way to commercial development. Other projects are assigned to consultants with backgrounds in system design and mining. Both types of development have led to programs that can be acquired for the cost of a tape or disk. This paper highlights several underground mining packages. These programs consist of: ? USBM model-developed by the United States Bureau of nines. ? PSU model-developed by Pennsylvania State University. ? VPI model-developed by Virginia Polytechnical Institute and State University. ? NUS model-developed by NUS Corp.

Jan 1, 1987

By Danny Chan, Shahram Tafazoli, Nicholas Himmelman, Edmond Chow

"While wearable technology has been garnering attention in the consumer market, enterprise and industry have just begun exploring its potential applications. Since February 2014, Motion Metrics International has been working in collaboration with Vandrico Solutions Inc. to apply wearable technology to improve productivity and safety in the mining industry.This article discusses the value proposition of using wearable technology to deliver critical notifications in mining. The advantages and disadvantages of various form factors are explored. The challenges, both specific to mining and in general to wearable technology, are defined. Finally, the concept of MetricsGear, the first wearable technology platform developed for mining by Motion Metrics International in collaboration with Vandrico Solutions Inc., is described. MetricsGear is designed to notify the user with minimal distraction to keep the user focused on his or her primary task and aware of mission-critical events. This focus and awareness allows the user to work more efficiently and safely. The mining process consists of a series of intricate stages, where certain events or conditions in one stage can have a huge impact on other stages. The notification of these critical events or conditions is vital for ensuring the overall efficiency of the mining process. Critical notifications can be classified as two types: timecritical events and contextual information. Time-critical events are situations where a timely response from a responder can have a significant impact on seizing an opportunity or mitigating cost. Some human-computer interaction (HCI) experts classify notification types based on the interruption, reaction and comprehension (IRC) framework. Time-critical events are classified to have high interruption, high reaction and low comprehension due to their urgency. The responder should have just enough information to identify the crisis and react as soon as possible (Chow, 2014). For example, when a tooth is lost during shovel operation, it is necessary to recover the missing tooth before it jams the primary crusher. The consequence of missing this critical time period is a jammed crusher that can cause the mine to be out of production until the jammed tooth is extracted (Baumann, 2013). In this case, the responder only needs to see an image to confirm if the tooth is missing and information to identify which equipment and when the tooth went missing (Fig. 1)."

Jan 1, 2014

"Iron ore is the source of primary iron for the world’s iron and steel industries. Its production can be reported as crude ore, usable ore or iron content of ore. Historically, the U.S. Geological Survey (USGS) used reported crude ore production from China in tabulations of world iron ore production while other countries have typically reported their production in terms of usable iron ore. When China’s crude ore production was tabulated with usable ore production from other countries, world iron ore production totals have been overestimated by 10 percent to a high of content and may include products such as concentrates, direct-shipping ore, pellets, and sinter.• Iron content, also referred to as metal content or grade, denotes the amount of elemental iron in the crude or usable ore.BackgroundIron ores consumed in the steel industry typically require an iron content greater than 58 percent before being considered commercially usable. Iron ores that are not commercially usable must undergo beneficiation to raise the iron content. Approximately 98 percent of the world’s usable iron ore production is consumed in blast furnaces to make pig iron, which is further processed to make steel.High-grade iron ore mines can supply usable iron ore, known as direct-shipping ore, to blast furnaces, with minimal physical processing and no beneficiation. With direct-shipping ore, the reported production for crude ore and usable ore are the same. Ore from low-grade deposits must undergo beneficiation to increase the iron content before it can be used by the steel industry. In this instance, the mined material is called crude ore and post-beneficiation concentrates are called usable ore; the amount produced will be less than the crude ore amount. With the notable exceptions of countries such as Australia and Brazil, most of the world’s iron ore deposits are low-grade and require beneficiation."

Feb 1, 2017

Almost all of the world?s zirconium is mined in the form of zircon (ZrSiO4), the majority as a coproduct of titanium mining from heavy mineral sands deposits. These are placer type deposits, in which the dominant mineral is silica but which also contain a suite of ?valuable minerals,? often consisting of a mixture of titanium minerals, various alumino-silicates and zircon plus a range of other mineral species. The composition of the valuable minerals in such deposits is known as the mineral assemblage. There is no reasonable consistent geological relationship between zircon and titanium minerals. They can derive from separate igneous rock deposits that rarely occur together. The connection emanates once these separate rocks have been eroded by weather and water, often across a very long geological period. Once this has happened, zircon and titanium minerals often find their way to the same locations because they share two major characteristics:

Jan 1, 2011

By G. P. JADAUN, ANINDYA PAIN, Aditya Rana, SAURAV RUKHAIYAR, N. K. Bhagat

This study compares three different techniques — decision tree, artificial neural network (ANN) and multivariate regression analysis (MVRA) — for predicting blast-induced ground vibrations in some Indian tunneling projects. The models’ performance was also compared with site-specific conventional predictor equations. A database consisting of 137 vibration records was randomly divided into training and testing sets for model generation. The results indicate that the decision tree is best suited to predicting vibrations. Furthermore, the decision tree suggests that the intensity of near-field ground vibrations is mainly affected by the total charge fired in a round, whereas the intensity of far-field vibrations is governed by maximum charge per delay and charge per hole.

By Nicole R. Henderson

Many mining engineering graduates enter the mining industry lacking training in mine emergency management. As a result, mining universities in the United Sates and other countries are beginning to form volunteer student mine rescue teams to train mining engineering students in handling mine emergency situations and give them hands-on experience managing potential emergency scenarios underground. In the early 1980s, the Missouri University of Science and Technology developed the first collegiate mine rescue team in the United States. For approximately 30 years, it was the only successful collegiate team until the Colorado School of Mines (CSM) started its program in 2009. Currently, there are at least five collegiate teams in the United States and one in Canada. At the Freiberg University of Mining and Technology in Germany, the goal is to adapt the Colorado School of Mines Mine Rescue Program to develop a collegiate team of its own. Currently, mining engineering students cover the theoretical basics of mine rescue in an occupational health and safety lecture and take a basic, one-day mine rescue training course at the Central Mine Rescue Station in Leipzig. The course covers the basic mine rescue topics and gives students the opportunity to experience working in elevated heat and smoke conditions while wearing breathing apparatus. This training gives students a small insight into the importance of mine rescue and mine emergency management. Collegiate mine rescue teaches students the importance of mine rescue and mine safety by giving them hands-on learning experiences before entering the mining industry.

Feb 1, 2014

By Elnaz Saminfar, Jae Bateman, Eric Westergren, Mark Trim

This paper presents a case study of two major Australian infrastructure projects that used digital engineering to facilitate design delivery: WestConnex Project (Rozelle Interchange), and Sydney Metro West (Eastern Tunnelling Package). The paper presents project overviews and building information modeling (BIM) execution and focuses on modeling techniques, software utilization, data management strategies and how the digital models helped the design-build team mitigate impacts to schedule by identifying clashes between disciplines before the execution of work. Finally, it demonstrates the positive and transformative impact of digital engineering on the design and construction of large underground infrastructure projects and highlights its role in asset management throughout the project lifecycle.

Jun 23, 2024

By Shinichi Konda, Gary Nishimura

"Thousands of years ago large glaciers carved much of the landscape in Puget Sound, depositing abrasive and granular soils including cobbles and boulders along with layers of clay and sand. Tunneling in this geology – common throughout much of the northern and Midwestern U.S. – is challenging and can be unpredictable. The use of pressurized face tunneling, most commonly with EPBs and slurry type machines, has made excavation in this geology more efficient, but difficulties still remain. Through analysis of recent projects in Seattle, Washington, USA, the authors draw conclusions as to the best TBM designs and operational parameters for this variable, abrasive and often difficult ground. Performance data is analyzed with an eye towards advancements that could further improve TBM tunneling in glacially deposited soils. INTRODUCTION Over the past several ice ages, extensive glaciers reaching across much of North America transported large amounts of soil and rock as they moved across the land. The substantial weight of the ice sheets mixed together a wide range of soil types along with a variety of rocks and boulders of all sizes. Many rock formations were reduced to pebbles or particles containing highly abrasive characteristics. Any boulders able to survive were generally comprised of harder materials which were scattered throughout the soil. This highly variable mixture of abrasive soils and high strength boulders can be found in many areas across the Puget Sound and other regions of the country. Wherever they are encountered, they often create a difficult and unpredictable mining environment for both equipment design and operation. Modern TBMs are optimized early in the design process for specific types of geology, and unexpected conditions can require extensive modifications. In addition, several operational parameters need to be adjusted to balance ground characteristics, and advance rates can be significantly affected in mixed and rapidly changing soil conditions. Both EPB and slurry machines can be used successfully in these conditions, provided their respective operating criteria are met. Ideally, an EPB is operated with a relatively thick muck consistency, which accommodates moderate changes in soil permeability and maintains a reliable pressure differential through the screw conveyor. However, this also causes higher wear on rotating components and requires more energy at the cutterhead. Alternatively, slurry machines typically operate best with a more fluid muck consistency that can be easily pumped through the extensive piping system. This tends to reduce the wear on the cutterhead and the power requirements of the cutterhead drive system, but also makes the machine more sensitive to changing soil conditions. Generally, the slurry piping system is also more capable of controlling high face pressures, although the screw conveyor of an EPB can also be designed to accommodate most high-pressure conditions."

Jan 1, 2016

By J. A. Marts, R. C. Gilmore, Jr. Bogin, S. A. Saki, J. F. Brune, J. W. Grubb

"Most, if not all longwall gobs contain explosive gas zones (EGZs), i.e., zones of explosive methane-air mixtures that can cause – and have caused – mine fires and explosions. If the coal is prone to spontaneous combustion, oxygen penetration into the gob must be avoided. This paper summarizes the significant research findings from five years of computational fluid dynamics (CFD) modeling research conducted at the Colorado School of Mines (CSM) under funding from the National Institute for Occupational Safety and Health (NIOSH). CSM Researchers have developed CFD modeling techniques to identify where and under what circumstances EGZs can form in longwall gobs and how EGZ formation and oxygen penetration depend on the ventilation method, face and bleeder ventilation parameters, injection of inert gases and the operation of gob ventilation boreholes. Recognizing these explosion and fire hazards is an important first step in improving the safety of longwall coal mines. CSM modeling research has shown that EGZ formation can be effectively controlled by adjusting ventilation parameters, choosing the proper ventilation pattern and injecting inert gases where necessary. INTRODUCTION In a project sponsored by the NIOSH Office of Mine Safety and Health Research, researchers at the Colorado School of Mines have examined gas compositions and flows in longwall gobs in order to assess explosion and fire hazards. Since gob areas are inaccessible, researchers developed a series of computational fluid dynamics (CFD) numerical modeling tools to characterize these hazards. A variety of CFD models were developed to cover progressively sealed as well as bleeder ventilated gobs for both coal and trona mines. The explosion and fire hazards posed by EGZs in longwall gobs can be summarized as follows.• If the EGZ lies closely behind the longwall face, flames and pressures from an explosion can penetrate the shield supports and reach the active face area, creating blast trauma, burn hazards and toxic, unbreathable atmospheres. • EGZs can be pushed around inside the gob by roof collapses and cave-ins. If they get pushed out into the face area, sudden methane inundations and explosion hazards in face areas can result. • Fresh air flowing into the gob can create an explosion hazard as the gas composition in the gob moves from fuel-rich inert to explosive, creating EGZs. • Ignition sources inside the gob can be frictional ignitions or spontaneous combustion. • Bleeder ventilated gobs are surrounded on all sides by an EGZ that forms along the fringe areas between the fresh-air ventilated bleeder entries and the methane-rich interior of the gob. It is suspected that diffusion flames can propagate rapidly along these EGZ fringes if an ignition occurs"

Jan 1, 2015

By Timothy Batchler, Khaled Mohamed

Standing supports have been used in coal mines for decades to enhance roof support capability. Occasionally, standing supports are used to resist the lateral movement of spalled ribs. Researchers from the National Institute for Occupational Safety and Health (NIOSH) are conducting a testing program for standing supports to investigate the effect of lateral loading on their vertical loading capacities and the factors affecting their lateral loading capacities. The Mine Roof Simulator (MRS) was used to determine the response of steel props to vertical and horizontal loadings. Finite element models (FEMs) were developed and verified using the tested steel props. Prop models were used to study the effect of a range of roof and floor materials — gray shale, shale and claystone — on the critical buckling loads of the steel props.

Dec 1, 2022

By AK Raina

Blasting is used in mining and civil excavations to break the rockmass for ore production or creation of space. One of the disadvantages of the method is that it causes breakage beyond the proposed excavation lines. Pre-split is used to control such breakage in rockmass. This paper introduces the use of digital image analysis technique (DIAT) to measure rock breakage and half cast factor (HCF%). A new factor, undamaged area (AUD%), is introduced to improve the prediction, owing to the shortcomings of the HCF%. A comparison of significant data of AUD% and HCF% showed that HCF% has a lacuna of overpredicting, whereas AUD% can be used effectively to address the issue. Artificial neural networks are used to solve the complexity of multiple variables involved in predictions and to ascertain the importance and sensitivity of such variables in prediction regimes. This method will help users to evolve blast-induced damage objectively. A comprehensive scheme of things for future developments is included, which can be helpful to researchers in defining their research in this area.

By BHAMIDIPATI S. SASTRY, KATTAMURI PAVAN KUMAR, ADITYA PANDEY

Several laboratory methods are available to determine the thermal conductivity of rocks, but most of them are complex and cumbersome. The present study explains the working principle of Lee’s apparatus, which is relatively simple, easy to fabricate and use, and provides consistent results. In the present study, thermal conductivities of sandstone cores obtained from an Indian coal mine are determined using Lee’s apparatus. An approach is discussed to determine the temperature gradient of sandstone specimens while cooling and is used to calculate thermal conductivity. The thermal conductivities of different sandstone specimens have values between 2.37 and 2.59 Wm−1°C−1. For different sandstone cores obtained from the field, properties including specific gravity, specific heat capacity, thermal diffusivity and porosity, along with thermal conductivity, were determined and highlighted in this study.

By J. Hunter

The Highland Uranium Project in Wyoming is an in-situ leach (ISL) facility owned and operated by Power Resources Inc. It is the largest uranium producer in the U.S. and the largest uranium producer by ISL in the western world. With its limited capital investment and low operating costs, the ISL technique has been demonstrated to be an effective and environmentally sensitive method for recovering minerals from these low grade and otherwise uneconomic orebodies.

Jan 1, 1996

By K. KAKLIS, O. SAUBI, Z. Agioutantis, R. JAMISOLA

Machine learning in the form of artificial neural networks was applied to investigate whether specimen load evolution can be predicted as a function of acoustic emission (AE) signals in the case of three-point bending (TPB) marble specimens instrumented with piezoelectric sensors. The ultimate objective of this study is to develop a model that can quantify rock behavior under loading that can lead to rock-failure prediction in underground structures subjected to bending, such as roof failure in development or production openings.

Nov 1, 2022

By G. R. Erdman

The industrial mineral filler plant of the Gouverneur Tale Company is equipped with a good dust collection system installed long before the recent popularization of environmental pollution. Credit for this fact is due to the foresight of Mr. R. S. McClellan, Project Manager and subsequent Vice President and General Manager of Gouverneur Talc, who recently retired as Vice President Engineering of the parent organization, the R. T. Vanderbilt Company. Also instrumental in the early stages of plant operation and the solution of start-up problems was J. A. Gustin who is now an engineering consultant located in Martinsville, Va. Credit is most certainly due to the late R. T. Vanderbilt, the company's founder, who favored and approved the investment in the necessary facilities that were far ahead of all competitors in the industry at that time.

Jan 1, 1972

By Ray Brainard, Adriana Ventimiglia, Amanda Kerr

Preliminary design is underway for a new Southern Nevada Water Authority (SNWA) project that will ensure one of America’s most reliable water systems by providing continued, reliable water service to existing and future customers. The Horizon Lateral is a $1.6 billion water transmission pipeline that includes 7–10 miles of 108-inch finished diameter rock and soft-ground tunnels. The tunnels will traverse volcanic rock in or around the McCullough Mountain Range and the surrounding alluvial basin. The tunneling community will find relevance in hearing about this critical infrastructure project from a leading wholesale water utility owner with a proven track record for on-time, collaborative projects.

Dec 1, 2022

By Emily Wortman-Wunder

As the 2011 president of the Society for Mining, Metallurgy, and Exploration, Inc., I am pleased to present the 2011 issue of the Transactions of the Society for Mining, Metallurgy, and Exploration, Vol. 330. A significant portion of the contribution that we as a professional society make is the publication of professional and technical papers that accelerate the advancement of scientific knowledge and enable the transfer of technology. Communication within the mining community is the key to a successful society. This technology exchange continues a tradition that dates back to the 1871 meeting of 22 mining engineers in Wilkes-Barre, PA, that resulted in the founding of AIME; those individuals envisioned that these transaction volumes “would form a most valuable and greatly needed addition to our professional literature.” This volume fulfills that pledge. The 2011 Transactions is the second Transactions to take advantage of new publication technologies. It appears solely in electronic format. The decision to go to an all-digital format for this longstanding publication was a difficult one, but one which will better serve the mining community. Based on the feedback from the 2010 Transactions in e-book format, I believe that the transition to the all-digital format was the proper decision. The 2011 Transactions contain some of the most interesting research from the past year, including a 10-year profile of roof and rib fall trends from the National Institute of Occupational Safety and Health (NIOSH) and a new cross-disciplinary application of the tools of epidemiology to assess and mitigate risk in coal mines . This 2011 Transactions comprise of a total of 82 technical papers (626 pages including index), including all 19 papers published in 2011 in the Technical Papers Section of Mining Engineering magazine (Vol. 63) and all 32 papers published in 2011 in Minerals & Metallurgical Processing (Vol. 28). Additionally, this volume contains 31 papers that are being published for the first time in this issue. The papers presented in this volume were written by some of the most distinguished professionals in the industry worldwide. All 82 technical papers were peer-reviewed. The process of review and publication requires much hard work by authors, reviewers and our publications staff. As the 2011 president of SME and on behalf of all our members, I would like to extend our gratitude to all whose volunteer efforts contributed to the publication of this volume.

Jan 1, 2011