Search Documents

By Keros Cartwright

Distribution of temperature within the lithosphere can be significantly affected by the movement of ground water. Stallman (1960) presented the basic equation for the simultaneous transfer of heat and fluid in a porous medium and first used earth temperatures to determine aquifer permeability. Subsequently, studies of rock and soil temperatures were used to determine the flow of water through clay layers separating aquifers (Bredehoeft and Papadopulos, 1965; and Sorey, 1971), and to locate shallow aquifers (Cartwright, 1968; Birman, 1969). Cartwright (1968) showed that shallow aquifers maintain a nearly constant temperature throughout the year and that heat is exchanged between the aquifer and land surface. These temperature data also suggest that shallow aquifers hydrologically connected to surface-water systems have significantly greater effect on temperature distribution than aquifers in the deep artesian basins. Water wells developed in the shallow glacial and dolomite aquifers to depths of over 122 meters (400 feet) in northern and central Illinois produce water at temperatures very close to the mean annual air temperature. An analysis of the character of the rocks and soils suggests that the tem¬perature gradient should, and does, vary according to changes in thermal conductivity due to changes in lithology. This is because, under conditions of steady and uniform flow of heat from the earth's interior to the surface, a greater temperature gradient is required in poorly conductive rocks than in highly conductive rocks to transmit the same quantity of heat. Based on estimated values of thermal conduc-

Jan 1, 1972

By Kevin L. Purdy

Chemical dewatering aids for mineral slurries generally fall into two classes: surfactants and flocculants, which can be used separately or together. Current industrial use of both types of reagents is summarized for sulfide and non-metallic minerals, as well as uranium and gold leach residues and coal refuse. Laboratory testing for reagent selection is briefly discussed along with reagent preparation. Chemical properties of the reagents which affect the suitability for particular applications are analyzed. [BLANK PAGES - Are in the original]

Jan 1, 1986

By Charles C. L. Smith

A review and comparison is made of the circuitry utilized for dc crane control systems. Anti-parallel three phase full wave thyristor bridges for dc motor reversing and speed control are compared with a single three phase full wave thyristor bridge for speed control and either contactor or static switching for reversing control to obtain complete four quadrant operation for crane material handling. In recent years the Harnischfeger Corporation has developed a solid state adjustable voltage control system to control the speed and direction of dc motors for crane applications and handling materia1.1 Shunt wound dc motors are utilized and speed is controlled in the motor base speed operating region at constant torque by a thyristor, silicon controlled rectifier (SCR), adjust- able armature voltage supply. The three phase thyristor bridge is the power controlling element of the dc adjustable voltage control. ELECTROTORQUE is the Harnischfeger Corporation registered trade name for this type of drive system. By controlling the gating signals or firing pulses to the thyristor bridge SCR's the dc output voltage can be varied over a wide range. This range is limited only by the magnitude of the ac applied voltage. To obtain operation of the motor in both directions two thristor bridges are connected in an anti-parallel arrangement. A typical schematic for two anti-parallel connected three phase SCR bridges is shown in Figure 1.

Jan 1, 1973

By G. Almgren

With the exception of sublevel caving, the most common method of underground mining in Sweden is the "cut-and-fill" method. It is normally used for mining non-ferrous metals , and' is used extensively in the complex sulfide ore mines of the Boliden Company in north and central Sweden as well as the mines of the STORA and Vieille Montagne Companies in central Sweden. All in all, the cut-and-fill method is used in 13 of Sweden's 45 mines. As the mines are relatively small, the volume of ore mined by this method represents only about 5 % of the total ore production in Sweden. The commercial value, however, is much large than this percentage would imply. The production volumes and grades of some typical mines are shown in Table I. As seen, when rated internationally, the grades are comparatively low. The prices are set according to ?international metal prices? as dictated by the London stock exchange, and in lieu of governmental support, rational management methods are critical in order to achieve satisfactory profit.

Jan 1, 1975

By R. Canello, J. Jenkins

El Abra has the world's largest leach, solvent extraction and electrowinning facility, The crushing plant capacity is 120,000 metric tonnes per day and the cathode production capacity is 225,000 metric tonnes per year. The El Abra mine and plant are located in the Province of El Loa, in Region I1 of Chile, 55 km. north of the city of Calama. The ore deposit outcrops on the southern slope of Cerro Pajonal at an altitude of 3,900 to 4,100 meters above sea level. The processing plant and camp facilities are located at a lower 3,300 meter elevation on an alluvial slope, 15 km southeast of the deposit. The operating company, Sociedad Contractual Minera El Abra, is 51% owned by Cyprus Arnax Minerals Company through the Cyprus Climax Metals Company subsidiary and 49% owned by Corporaci6n Nacional del Cobre de Chile (Codelco). The present paper describes the ore reserves, mine operations, crushing, leaching, solvent extraction, electrowinning and infrastructure facilities.

Jan 1, 1998

By K. N. Han, P. B. Queneau, A. Stojsic, M. J. Collins, V. J. Ketcham, R. M. G. S. Berezowsky, W. D. Vardill

The bulk of the ore found in the Lihir Island deposit is refractory in nature, with the gold contained in auriferous pyrite. In support of an evaluation of the development of this deposit by Kennecott (a wholly owned subsidiary of RTZ) and Niugini Mining Ltd., testwork has been carried out at the Sherritt Research Centre to demonstrate the amenability of the Lihir ore to pressure oxidation pretreatment to liberate the refractory gold. The results of pilot plant treatment of the Lihir ore in a continuous circuit with a feed rate of between 10 and 30 kg/h ore are described. The integrated circuit comprised pressure oxidation, residue washing, and gold recovery from the washed residue by carbon in leach or carbon in pulp cyanide leaching. Significant factors affecting gold recovery included temperature and retention time in the pressure oxidation step, and the concentration of soluble chloride in the feed. Gold extraction from well washed ore, after oxidation at 210°C for 66 minutes in the autoclave, was typically between 94 and 96%, compared with less than 30% by direct cyanidation.

Jan 1, 1993

By D. Newman

"The U.S. stone industry is in a transition from surface quarries to single and multiple level underground stone mines. The factors driving this transition include surface quarries; ? reaching their economic stripping ratio, ? encroaching on the mineral reserve boundary where the remaining reserves are below the active pit, ? dust, noise, and blast vibration concerns as suburban neighborhoods and development move into formerly rural areas. Ground control is critical to the success of a safe and productive, mining operation. The primary focus of the ground control engineer in an underground stone mine is the stability of the roof or back, development and benched pillar stability, stability of the sill pillar between vertically adjacent mining levels, and floor stability. Roof stability begins with the selection of a stable back horizon based upon the presence of a thin shale parting, stylolite, or other discontinuities from which the production shot can easily ""peel"" away leaving a stable back stratum. Room width and the decision of whether to bolt the roof, the bolt length, bolt type, bolt diameter, and spacing of the support is controlled by the thickness, fracture spacing, jointing, and material properties of the back strata. Horizontal stress controls the header and crosscut azimuth as to avoid driving perpendicular to the maximum horizontal stress direction. Stable pillar dimensions depend upon the interaction of the; ? vertical stress resulting from overburden thickness and multiple level interaction of overlying level(s), ? mining height during development and the final mining height after floor shots are taken while benching, ? presence of faults, folds, or joints passing through the pillar, and ? stone lithology recognizing that the presence of oolitic bands, shale partings, and bentonite beds create zones of weakness that can destabilize an otherwise competent pillar. Floor stability is typically not a significant issue for underground stone mines because the bearing capacity of the stone exceeds the vertical pressure transferred through the pillar. However, floor heave can be a ground control issue where shale partings, moisture sensitive strata, weak stone bands, or horizontal stress is present. Roof stability and pillar stability problems can be initiated as the floor heave enables the pillar and roof to settle. The ground control issues for underground stone mines are most clearly presented through a series of case histories. The case histories presented in this paper are a mix of ground failures and successful mining. The focus is on the geotechnical data required for underground stone mine ground control for roof, pillar, and floor design and stability analysis."

Jan 1, 2016

By T. Klemetti, W. H. Su, M. A. Van Dyke

Entry stability in coal mines is dependent on geologic conditions and engineering controls. Most engineering controls in ground control are predictable and standardized for typical geologic conditions. However, geologic anomalies may exist that are difficult to detect with traditional core hole drilling. Borescopes offer a cost-efficient way to gather more geologic data between core holes. Additional data obtained from borescope results provide a clearer picture to enhance detection of hazardous conditions due to geologic anomalies. The equipment, methods, and analysis of borescope results provide geomechanical engineers with a clear understanding of strata behavior and the best information to implement roof control plans and supplemental support to enhance miner safety and health. INTRODUCTION Borescope technology has changed very little since its inception. However, the idea to use borescopes to examine roof strata started with the U.S. Bureau of Mines in 1979 with the production of a fiber-optic borescope (FitzSimmons, et al., 1979). The first documented use of a borescope in the coal mining industry began during the 1980s in Australia by researcher John Shepherd. Shepherd’s idea was to use a borescope to collect a series of data points from the roof lithology and compose a geologic cross section. The cross section was then used to identify key features that suggested the beginnings of roof failure. The features Shepherd identified were bedding plane separations in the roof and low angle, extension, and tensile failures. Shepherd also suggested that the borescope findings could be used for geologic mapping for lithological variation, fracture distribution, and determining if supplemental roof support was needed (Shepherd, et al., 1986). In the United States the first publication about borescope usage for coal mine stability assessment was by Su and associates in 1999, who specifically related the combination of using borescope, geophysical, and corehole data to produce geologic hazard maps (Su et al., 1999). This work directly linked the usage of a borescope with the design of supplemental roof support. The use of borescopes in mining was adopted industry wide by the 2000s. Operator case studies were being published using borescopes to aid in supplemental support recommendations and hazard mapping. An Australian study published in 2007 based the optimization of secondary support after each longwall pass on the results of borescope data. The study stated that the borescope was an invaluable tool for understanding roof behavior (Black, et al., 2007). In 2009, a publication by the National Institute for Occupational Safety and Health (NIOSH) took the concept of borescoping one step further. The work centered around creating a roof quality index (RQI) for limestone mines based on borescope data. The RQI attempted to assign a ranking to establish the nature of the roof and its stability (Ellenberger 2009). In theory, this would have been a very useful tool, but the RQI system has not been widely adopted in the industry.

Jan 1, 2019

By S. M. Carpenter

In an ever increasing ?carbon? society; management and growth will be measured by one?s carbon footprint (or output). Industries, especially mining, are under an ever increasing scrutiny of carbon, water and environmental mandates. These mandates are measured by the emissions caused by the combustion of fossil fuels. The fundamental building-block for any business, strategic or management decision must be based on an understanding of one?s ?footprint?. The scrutiny is most stringent for the commodities producers, power producers & fuel suppliers in the energy market. An overview of currently acceptable standards, application of those standards and nuances experienced in collecting the data necessary to analyze and complete a company?s carbon footprint will be presented. A lack of regulation, the fear and expectation of new and ever constraining rules, regulation and a change in the federal administration is a recipe for uncertainty in the marketplace.

Jan 1, 2010

By John T. Langstaff

Rock bursts in the deep metal mines of the Coeur d’Alene district present an ever increasing problem in the safe and economic mining of the district’s silver, lead and zinc ores. Hecla Mining Company operates two mines in the district - the Star, a 1100-ton/day lead-zinc mine, and the Lucky Friday, a 750-ton/day silver- lead mine. Rock burst problems at both operations prompted Hecla management to make an all-out attempt to find a practical method of predicting and eventually controlling these bursts. Research by personnel from the Denver Research Center of the Bureau of Mines at ASARCO's Galena Mine indicated that a recognizable pattern of seismic activity preceded some bursts and this activity could be precisely monitored by present- day, off-the-shelf electronic devices. Using information gained by the Bureau and other sources, Hecla designed and installed a 24,- channel seismic monitoring system in the Lucky Friday mine. Installation was completed in December 1973 and after a year of successful operation, it was decided that a similar system would be installed in the Star mine. This second installation was completed in June 1975. Both systems are now operating and providing continuous information on underground seismic activity. Each monitoring system consists of a network of geophones with attendant amplifiers that are connected by shielded cable through an interfacing device to a computer. The origin of each seismic event is determined by the computer and a three-dimensional location is printed out. This information is plotted daily and is used to pinpoint rock burst prone areas and chart their relative seismic activity. This paper will review the causes and effects of rock bursts in the Coeur d'Alene district, the equipment and operation of the microseismic system at the Star and Lucky Friday mines, and the results obtained to date.

Jan 1, 1977

By W. S. Fyfe

The future environment of our planet, with the concept of sustainable development, has moved to centre stage of all future plans for development. This global view is new. It presents great opportunities and challenges for the Earth Sciences. We have the tools to describe our environment on all scales - planetary to molecular levels. We must respond to this great demand by world society.

Jan 1, 1990

By A. D. Davis

The Bear Butte Creek watershed, in the northern Black Hills of South Dakota, shows the effects of past mining activities in the form of dissolved metals and arsenic in stream water. Bear Butte Creek, during normal flow periods, loses all of its discharge to sinkholes that recharge the Madison Limestone aquifer. This work focused on the geochemical transport and fate of arsenic and on understanding ground-water flow conditions in the Madison aquifer through development of a three-dimensional ground-water flow model that was coupled to a geographic information system (GIS). Stream sampling and discharge measurements helped determine sinkhole losses and loading rates. Column laboratory tests provided data on arsenic adsorption and the mixing of stream water with aquifer water, which also was simulated with the geochemical models, pHREEQE and NETPATH. The models and GIS can be updated with new information and will be useful in managing the water quality of the Madison aquifer.

Jan 1, 1997

By William F. Lawrence

Within ten to fifteen years, coal-fired power generating stations will be producing over 40 million tons of coal-ash annually in the United States. The largest part of this ash will be emitted from the boilers, entrained in the off-gas stream and trapped as flyash. However, about 15 percent (six million tons) will he removed from furnace bottoms as bottom ash or molten coal-ash slag. In current practice, the molten coal-ash slap is generally water quenched and then transported either as a slurry or in granular form to storage or disposal areas. Although a small amount of this slag is marketed as abrasive grit or as roofing granules, most of it is considered a waste material which must be disposed of at considerable cost to the power companies and therefore to the public. The accom¬panying economic loss in terms of unused raw materials and displaced land is not as obvious but is just as real. The Coal Research Bureau at West Virginia University under the sponsorship of the U. S. Bureau of Mines has been examining the possible utilization of both coal-ash slag and flyash in the mineral wool industry as a method of partially alleviating the growing national problem of solid waste disposal. The potential marketing situation for mineral wool manufactured from coal-ash is illustrated in Figure 1. This bar graph depicts the growth in value of mineral wool shipments1 from 1949 through 1966. In this 17-year period, the value in¬creased by over 350 percent, more than 20 percent per year, despite a decrease in unit cost of mineral wool. It therefore appears likely that coal-ash could find a steady market as a supplement to existing sources of raw materials for mineral wool production.

Jan 1, 1970

By Peter F. Mataich

The phosphate mining industry is a highly competitive one, one in which survival depends on the plant's ability to produce at costs equal to, or below, the competition. The solution toward getting costs down is usually one of scaling up the plants to get the most tons through at the lowest possible cost. Control of these plants has been an art. Few of them are well instrumented because until a few years ago reliable instrumentation was non-existent. International Minerals and Chemical Corporation was a pioneer in applying computer techniques to ore reserves analysis and mine planning and the success in these areas led to the question of whether we could not extend the advantages of computer processing into the plant itself. There was a great deal of doubt on the operator's end that this could be done successfully because of the lack of instrumentation and the fact that plant control was largely an art that was learned only after many years of experience. However, in 1965 the instrumentation picture began to look up and the new generation of process computers just coming on the market were considerably lower in cost than the previous ones. A preliminary study of the installation costs and the probable benefits that could be realized from computer control convinced us that a process control computer should be seriously considered for a new phosphate mining plant which was being designed.

Jan 1, 1969

By Malcolm J. McPherson

This paper describes the algorithm used in a BASIC program for an IBMXT microcomputer, to simulate the underground mine climate. The program called CLIMSIM has been developed and refined over several years as a result of considerable use at operating mines. The program has been designed to be easy to use and be understood by the practicing mine ventilation engineer. It provides predictions of the work place climate, so that the optimum ventilation/cooling system can be designed to obtain a certain air cooling power or effective temperature at the work place. An example is given of the application of the program to a mechanized cut and fill stope at the Homestake gold mine in South Dakota.

Jan 1, 1986

By Billy W. Parks

This paper reports on the first 2 years in operation of a special-purpose coal handling rig which provides blending, temperature reduction, and continuous, automatic mechanical sampling as part of midstream barge to ship coal transfers. Briefly reviewing some of the characteristics of coal handling peculiar to midstream transfers, the paper discusses how the most beneficial aspects of midstreaming were enhanced through the design of this blending and sampling rig.

Jan 1, 1986

By A. Pezzuto

"Pipes are used on mine sites in a variety of applications including transport of slurry, conveying clean and processing water, and in mine dewatering. Mine waters and slurries can cause pipe wear and failures via several mechanisms (or combinations thereof) such as abrasion, scaling, and corrosion. Polyethylene (PE) pipe materials have grown in popularity over the past several decades due to their chemical and mechanical properties (e.g., inertness, flexibility, relatively low density) and low cost. While PE is generally resistant to corrosion, it is subject to abrasion. To combat this, a novel, rubber-like liner is in development. In addition to comprehensive abrasion testing, however, the liner must be evaluated to see how it performs under other conditions. Here, a brief field study is described that tested PE pipes with the new liner against traditional PE pipes to specifically assess mineral scale buildup. The study was conducted in the Reiche Zeche study mine in Freiberg, Germany in six different locations with varying water qualities and flow conditions. INTRODUCTION Water and slurry conveyance are major operations on and around mine and mill sites, from mine dewatering, to tailings transport, to water treatment processes. Conveyance systems in such applications can include great lengths of pipe materials along with pumps and monitoring instruments, and thus represent significant capital investments. Due to the variability of the physical and chemical properties of water and slurries, pipe materials are subject to a wide range of conditions. These can cause pipe wear and eventually failure leading to serious economic, environmental and social, consequences. While pressure-induced pipe failures (e.g., ruptures or ""bursts”) can be immediate, most failure mechanisms involve gradual processes. Scaling and sedimentation can present major problems for pipe systems conveying highly mineralized waters. Sedimentation generally refers to the deposition of suspended solids, such as sand, clay, silt, or organic matter onto pipe surfaces. This phenomenon can occur due to a decrease in water velocity or particle collisions with the pipe wall. Scaling, on the other hand, commonly refers to the deposition of precipitated mineral salts (including oxides and hydroxides) onto pipe surfaces. Mine waters often have extremely high ion concentrations (i.e., high dissolved solids content) due to their interaction with enormous surface areas of minerals, which are exposed during mining and processing operations (Brown and Barley, 2002). As these waters are transported, slight changes in temperature, pressure or chemistry (e.g., pH or ORP) can cause instability with respect to ion solubility such that salt precipitation begins to occur. “Seed” crystals can rapidly grow and attach to pipes, either due to local surface phenomenon near the pipe wall (e.g., which can promote coagulation) or sedimentation of the precipitated solid. Whether due to suspended or precipitated solids, as the solids begin to stick to pipe walls, “aging” or hardening processes can commence; and the build-up of scale can become self-perpetuating as the scale itself provides an attractive “nucleus” for further attachment of particles or crystal growth (Muryanto et al., 2014). Over time, scale-buildup reduces the effective pipe diameter, which can ultimately result in decreased flow velocity, clogging and, in some instances, bursting (Dirany et al., 2016)."

Jan 1, 2017

By Paul E. Epstein

Despite the controversies that have surrounded asbestos over the past 20 to 30 years, no knowledgeable authority has doubted the usefulness of this material. Were it not for the health risks associated with the manufacture and use of asbestos products, its physical and chemical characteristics would continue to be hailed as an undeniable boon to mankind. However, it has become clear over the past 30 years that like other major contributors to our modern industrialized society, asbestos must be handled responsibly and with the full understanding that lack of care can lead to injury, suffering and death. In this sense, asbestos shares characteristics with nuclear power, pesticides and even motor vehicle usage. It is unlikely that modern society would be willing to walk away from the benefits bestowed by any of these valuable resources. Rather, the appropriate response to the identification of danger is to define the type of risk, quantify its incidence, search for methods of decreasing the risk and implement programs to achieve the goal of minimization of risk. We should recognize at the outset that the risk cannot be diminished to zero without elimination of the material entirely from our midst. The concept of acceptable risk is a complex issue involving medical, legal, financial, moral and even psychological factors that defy precise quantification. In essence, the major danger produced by exposure to asbestos is its potential effects on the respiratory system. Despite the fact that asbestos workers have constant skin contact with the material and porbably swallow it in the course of their activities, inhalation of the fibers is recognized as the major health risk associated with its use. Aerosols of asbestos are inhaled not only by miners, millers and fabricators but also by urban dwellers who have no direct occupational contact with the material. This occurs because asbestos has been applied to our buildings and has been used in a wide variety of products that touch our daily lives. While it is estimated that three to four million people in the United States have been occupationally exposed to asbestos, the number who have been non-occupationally exposed is many times that number.

Jan 1, 1984

By W. C. Yates

Lack of visibility from cabs of the large haulage trucks used in open-pit mines has become a serious safety problem. This Anaconda research program was conducted to develop a low-cost system for alerting haulage truck operators of the presence of small vehicles in their blind areas. Several systems, developed and tested to help solve this problem, are summarized and evaluated in this paper. As the size of the haulage trucks used in large open-pit mines has increased, so have the blind areas. Mine utility vehicles, pickup tucks and cars become concealed within these blind areas and, thus, become a serious safety hazard. Figure 1 shows the typical blind areas of a 150-ton haulage truck. The areas of greatest concern are those at the rear center and front right corner of the truck. It is within these areas of "no visibility" that numerous small vehicles over the years have been crushed by the large haulage trucks at various mine sites. Although the occupants in most instances, have escaped the vehicle before it was destroyed, injuries and deaths have occurred. The accidents, in most cases, were attributed to negligence or carelessness on the part of the driver of the smaller vehicle, but the problem of limited visibility still exists, and a solution is needed.

Jan 1, 1982

By Louis W. Cope

The various types of placer deposits will be described as an introduction to the subject. The several methods and machines used for sample taking and processing will be discussed. The advantages and disadvantages of each will be covered. Included will be mistakes and pitfalls of placer sampling and sample reduction.

Jan 1, 1987