Search Documents

By J. J. Bean

The development drilling program of the Copper Cities mine indicated that the molybdenum content of the ore would be about 0.011% MoS2' The molybdenum content of the Miami mine at the same time was about 0.025% MOS2' The Miami mill had a very successful molybdenum operation which used bleeder turbine steam from the Miami power plant for the steaming operation. The much lower grade of the Copper Cities ore, the absence of a source of low cost steam and the use of sodium aerofloat as the copper collector which Miami experience indicated did not respono readily to the steaming technique made very doubtful the success of a similar operation at Copper Cities. However, the relatively few pounds of copper that could be recovered from the low grade Copper Cities heads made very desirable the recovery of the molybdenwa,as a source of additional revenue. Accordingly, shortly after the Copper Cities mill began operation, a research program was instituted to develop a suitable method of molybdenum recovery. This program explored first, the successful steaming process then in use at Miami and as expected, found it unable to decompose the sodium aerofloat copper collector. The known chemical depressants were then tried without much encouragement. Finally the copper concentrate was dried, not roasted, to 2-3% mOisture and this along with sodium ferro-cyanide and cyanide resulted in sufficient copper depression that a final molybdenum concentrate containing 1.0% CU could be made. The bench scale testing was followed by pilot plant testing. Sixteen

Jan 1, 1972

By Owen Kingman

This paper discusses grade control of ore mined at Tennessee Copper Company. Mineral zoning and the influence of mineral zoning on production grade are discussed and illustrated. In order to make this most understandable we will first briefly examine the flow sheet at Tennessee Copper to indicate the path followed by the raw material toward its various products. Then we will discuss some of the characteristics of the ore, specifically the distribution or zoning of the minerals in the ore which cause some of the grade control problems. Finally we Will discuss same of the steps that are taken to combat these problems. The flow sheet is illustrated as plate 1. The mined ore is allied to obtain 3 usable products: Copper concentrate, iron concentrate and zinc concentrate. Copper is found in the mineral chalcopyrite, CuFeS2. The Copper concentrate from the mill contains about 20% copper. These concentrates are smelter in reverberatory furnace and Pierce-Smith converter to blister copper containing 99.2% copper. Some metal is cast into 360 lb. pigs and shipped to the refinery. Some is made into shot copper and used locally to make copper sulfate. Copper sulfate is marketed from Copperhill principally in fungicides.

Jan 1, 1960

By J. A. Chermak

Piles of sulfide-bearing overburden, ore, and tailings have the potential to generate acid drainage (AD) when exposed to an oxidizing environment. Laboratory column experiments were conducted using acid-generating overburden material with an added surface amendment of limestone and/or lime. Artificial rainwater was introduced and allowed to drain through the columns. Results showed that the limestone and/or lime reacted with the acidic rock, resulting in the precipitation of a hardpan layer of gypsum and amorphous iron oxy-hydroxide at the surface. The hardpan layer significantly reduced the effective permeability of the column. Based on this study, hardpan layers can be created as chemical caps to significantly reduce the infiltration of rainwater and snowmelt into acidic overburden or tailings material. Unlike traditional capping methods (for example, clay and high density polyethylene (HDPE) covers), chemical caps are self-healing.

Jan 1, 1996

By Arthur S. Radtke

The structural setting of disseminated-replacement gold deposits of the Carlin-type and other aspects of their genesis are closely related to events which took place during the evolution of the Basin and Range province. The deposits formed as a result. of chemical and physical processes which took place at shallow depths in the roots of hot spring systems at moderate temperatures (about 200°C) and low pressures (about 25 bars) (Radtke and Dickson, 1974). Locations of Carlin-type gold deposits in the Basin and Range province are shown in Figure 1. Most of the block-faulted mountain ranges in the Great Basin formed by tectonic activity that happened since Miocene time, although faulting in some places probably began in Eocene to Oligocene time (Hamilton and Myers, 1966). The Carlin-type deposits are spatially related to Basin and Range-type faults: Many deposits, such as Getchell, Pinson, Preble, and Cortez, occur along the flanks of ranges, while other deposits, including Carlin (Radtke, 1974) occur within the ranges in areas characterized by crosscutting and intersecting high-angle or Basin and Range-type faults. The association of the ore deposits with Basin and Range-type faults is evidence that ore deposition is young, Miocene or later. The steep, high-angle faults played three roles: first, they provided deep channels for upward-flowing solutions; second, in preparing the rocks for fluid penetration by brecciation and general rock dislocation; and third, they moved sedimentary carbonate rocks, favorable for ore deposition, from deep levels to near-surface positions where the physico-chemical conditions were more suitable for the deposition of ore.

Jan 1, 1976

By Yi Luo, Jian Yang, Hua Jiang

Surface subsidence induced by underground coal mining activities, especially longwall mining operations, can cause various problems to interstate highways ranging from structural integrity to drivability to safety. Accurate subsidence prediction, correct influence assessments and effective mitigation measures are the keys to ensuring the safety of highway traffic. The surface subsidence prediction program, called comprehensive and integrated subsidence prediction model (CISPM), was developed based on the principle of influence function method and has been validated with a large number of subsidence measurements. In this paper, the techniques to use the predicted final surface movements and deformations for assessing their influence on the integrity and functionality of highway structures — such as road surface pavements, concrete slabs and transverse joints — vehicle dynamics, comfort level and drivability are presented. A number of mitigation measures to protect the highway structures and to ensure traffic safety are proposed, along with an application case.

By D. A. Shock

Utilizing the technology developed for oil well stimulation by hydrofracing, a disposal system which permanently fixes the waste has been proven. Large quantities of radioactive waste can be processed by a single well system making this method an attractive method for permanent radioactive waste disposal. The system depends on locating a relatively thick formation of impermeable, but easily fracturable rock such as a shale, creating a horizontal fracture, pumping the waste into the fracture in a form which will subsequently solidify and seal the fracture from the well system. The paper presents the theoretical considerations from creating and extending horizontal fractures and how these considerations were used in designing a waste disposal system which is now operating.

Jan 1, 1964

By Harley G. Pyles

Rotary Percussion drilling has shown great improvement over rotary drilling, when hard roof is encountered. In addition, Rotary Percussion drills have eliminated the need for air drills in many applications. Improved drilling rates have been achieved but roof bolting is still a bottleneck in many operations and the demand for further improvement will continue. Drilling rates beyond current performance is limited by the capabilities of existing drill steels and bits to resist increased horsepower input. The most apparent immediate solution to improved drilling is to increase the strength and rigidity of the drill steels. Drilling experience indicates that a l-1/2" diameter or 1-5/8" diameter hole can be drilled as rapidly or 'more rapidly than the standard 1-3/8" diameter hole. Greater torque and thrust capacities can be achieved through the use of larger O. D. and I. D, steels, however, this is only possible if the larger hole sizes can be made allowable. Large diameter anchorage shells can be made available at a slight extra cost.

Jan 1, 1965

By C. Huang, S. Lin, Y. J. Wang

Introduction A mine characteristic curve is of great importance for both theoretical analysis and daily management of a mine ventilation network. Ventilation engineers are well acquainted with the ways of obtaining and using a mine characteristic curve that is conventionally associated only with single-fan networks. However, for a multiple-fan network, difficulty has long been recognized in defining the curve, not to mention, obtaining or using it. To extend the concept of mine characteristic curves for a multiple-fan network, a subsystem-based approach has been introduced by Wang (1992a). He defines a subsystem characteristic curve for a multiple-fan network and discusses the numerical procedure for constructing the curve. A graphical method of obtaining a subsystem characteristic curve for serial-parallel, multiple-fan networks has also been accomplished (Wang, 1992b). In spite of the maturity of the fundamental concepts related to and the numerical analysis tool for a multiple-fan ventilation network, information regarding the related laboratory tests is very scarce. To make up this gap, laboratory experiments have been done by using a two-fan experimental network. This paper presents the methodology and major findings regarding the construction and features of a subsystem characteristic curve. Characteristic curves and measurement fundamentals A characteristic curve A characteristic curve is a graphic presentation of the relationship between any two variables of a two-terminal component. It is typically defined in the form of a quantity-pressure curve for a ventilation component, which can be a single branch (airway), a fan, a regulator, a portion of a network or even a whole network. If a component is a single branch, the curve is called a branch characteristic curve. If it is a fan, then the curve is called a fan characteristic curve, and so on. Figure I illustrates the characteristic curves of some typical ventilation components. A general method for obtaining a characteristic curve from measurement is to apply an adjustable-pressure source between the two terminals of a component and measure the quantities corresponding to the different pressures. Mine characteristic curve A single-fan network can be easily divided into two ventilation components, the fan and the remaining network. The latter consists of only branches and regulators. Under this subdivision scheme, two characteristic curves can be constructed. They are the fan characteristic curve and the characteristic curve of the remaining network. The latter is referred to as the mine characteristic curve or the system characteristic curve. Although the general method for constructing a characteristic curve from measurement can be applied to obtain a mine characteristic curve, there is a shortcut for constructing the curve by introducing a mine resistance factor R. It is a constant if all of the resistance factors in the network are constant. R relates mine pressure H with quantity Q as in: H=RQ2 (1) For a given R, Eq. (1) can be directly used to plot a mine characteristic curve by assigning a series of Q values and calculating the corresponding H values. Hence a shortcut to constructing a mine characteristic curve is to measure one set of mine pressure H and quantity Q values, calculate the mine resistance factor R using Eq. (1) and then plot the curve. Subsystem characteristic curve Applying a similar scheme as is used for a single-fan system, divide a multiple-fan network into two components, a fan under consideration and the remaining network that contains all the other elements (branches, regulators and remaining fans) of the network. The fan under consideration

Jan 1, 1994

By R. H. King

Underground coal mining machinery utilizes portable electric sables, "trailing cables." to obtain power from load centers or distribution boxes. Cables are frequently damaged since mobile equipment, poor lighting, and restricted space are inherent to coal mining operations. Normally, the damage is repaired by splicing--the joining of one or more severed conductors and replacing insulation and jacket. Figure 1 illustrates a typical single conductor splice. Although the repair seems simple, difficulty of the splicing process is exemplified by the many safety hazards and frequent production delays that result from defective splices. Forty-two cable splice related injuries were reported to the U.S. Bureau of Mines in 1972 and 1973. Additionally, 17 splices related fires were reported in the three year period prior to December 1972. Assuming the damaged area is quickly located, an average splice time for a two conductor cable is twenty minutes. Some operators estimate this delay is incurred once per day per operating section. If one ton per minute is averaged throughout the shift, each unit could loose 4800 tons per year from splice delays. An estimated cost for materials and labor to make a splice is $20. The expenditure could result in a $4800 annual cost per section. The estimated expense does not include wages of other personnel waiting for the repair to be completed. Nevertheless, labor and materials cost is minor compared to the income lost from decreased production.

Jan 1, 1975

By Charles M. Pelanne

Without insulation we could not survive on this planet. This may sound like a self-serving statement but it is a fact. The blanket of air which surrounds us is a very effective insulating blanket, allowing some shortwave solar radiation to warm us during the day while retaining the longer infrared radiation at night. Our life on earth is very much dependent on materials performing an insulating function without being thought of as insulation, clothing, fur, window glass, the ice of an igloo etc. The mechanisms of heat transfer involved in these materials are analogous to those involved in engineered insulations - Engineered insulations are designed for maximum effectiveness for given conditions within the applicable retraints. Engineered insulations are very effective! As an illustration let us consider this graph (Figure 1). It represents: 1. The radiative heat transfer between two 1 foot2 (0.0932) radiantly black surfaces, one at 100F (38C) and the other at the temperature indicated on the bottom scale. This does not include the convective and conductive heat flow of the air, both of which are significant but small in comparison. 2. The heat transfer resulting from the placement of 1 inch (25.4 mm) of insulation [10 pcf (160 kg/m3) ceramic fiber] between these two plates.

Jan 1, 1976

By J. S. Y. Wang, R. C. Trautz

To evaluate the potential for water seeping into an underground opening, a 9-m- (30-ft-) long drift was constructed in the unsaturated fractured tuff at Yucca Mountain. Forty seepage tests were performed by releasing finite volumes of water at a constant rate into short test intervals located in boreholes positioned above the drift. The seepage threshold flux, defined as the liquid-release flux at and below which water will not drip into the opening, was determined for 10 test intervals. The seepage data, observations and model results indicate that a seepage threshold exists because a capillary barrier diverts water around the opening.

Jan 1, 2002

By M. Wason

An Ore bed magnetic liner element is made of permanent ceramic magnets embedded in a rubber molding. (See figure 1) They are difficult and expensive to manufacture correctly. Therefore, the lining for a complete mill is expensive, as high as 400% more than conventional rubber liners. The magnets are not very resistant to impact as they are very brittle. Mills of 12 feet or more can use only I inch balls; mills under 12 feet can use balls of 1-1/2 inches. These liners are therefore used in regrind applications with small balls or in secondary pebble mills. Rubber liners for these applications last a long time, so if life was the only consideration, the pay back for these liners would be longer than the life of the mine. The Ore bed liner and its bed of ball chips or magnetic ore is relatively thin and the surface of this bed has a high coefficient of friction. The liners are made so that opposing poles are situated next to each other and that the mill shell and the bed of ore or ball chips completes the magnetic circuit. (See figure 2) The combinations of these properties results in a very efficient liner. Due to the low profile of this bed, there is no material that is lifted too high, so we have a very compact charge with very high attrition, good for fine grinding. These liners have shown a 10% ball consumption reduction and a 10% lower power draw for the same capacity. Due to the magnetic orientation, the bed is formed in a wave shape along the lines of magnetic force. Tests conducted at a copper mine in the southwest United States have confirmed these findings. The mills where the liners were tested are 10.5 feet by 16 feet Hardinge regrind mills operating as overflow ball mills.

Jan 1, 1999

By J. L. Arola

Since start-up of fluxed pellet production in August: 1987, the Minorca Mine has made a number of process changes to improve pellet quality and productivity. Quality improvements include: 1. Installation of a contraction t:ester. 2. Installation of on-line calcium and silica analyzers. 3. Process autocation changes. Productivity improvements include: 1. A second fluxstone storage bin and feeder. 2. A new vacuum pump and disc filter. 3. A filter aid addition system. 4. Enclosing the filter cake reclaim feeder. 5. A new grate bar cleaner.

Jan 1, 1989

By Ralph M. Stricklen

The need to move large tonnages of slurry has grown as mines have become larger. As existing tailing depositories are filled up, new mines developed, or environmental requirements dictate, it becomes necessary to transport tailing particularly over longer distances. A typical slurry transport system is shown in Figure 1A. Figures 1B, 1C and 1D show sketches of the system auxilliary components: feed box, receiving sump and drop box, respectively. There are two basic types of slurry transport systems, packed flow and slack flow. Packed flow is typified by a pipe running full; slack flow by a launder or pipe running less than full. Slack flow in launders or channels is also referred to as open channel flow. Generally slack flow slurry transportation involves a flow with less than 65 per cent solids, and there is an upper limit on particle size, depending on the slope of the system.

Jan 1, 1984

By John E. Tilton

Mining is one of the oldest human activities. It goes back at least to the Bronze Age and possibly even the Stone Age. The Romans mined copper in Spain and tin in England some two thousand years ago. The writings of Agricola in the 16th century show that mining was important in the Middle Ages. Today we mine more mineral commodities in greater tonnages than ever before. This long and fascinating history closely tied with the economic development of the human race is one of the charms of the mining industry. It also, unfortunately, gives rise to some widespread misconceptions.

Jan 1, 1997

By S. Sener

In this investigation, the changes in the grindability of both ulexite and colemanite related with the different structural modifications created by the heat treatment were examined with respect to work index (Wi). The effects of the heat treatment temperature and time on grindability index were also investigated. It was observed that, heat treatment significantly affected on the grindability of ulexite. The work index of original ulexite was found 7.11 kWh/shton and decreased to 3.5 kWh/shton level within 200-480°C for 60 minutes. On the other hand, the work index of original colemanite was found as 6.48 kWh/shton and no appreciable change was observed when heated up to 320°C. Thermally assisted comminution can be used to improve the grindability characteristics of ulexite. Besides, the different behaviour of ulexite and colemanite under heat treatment can be used for their separation. The artificial mixture of ulexite and colemanite could be separated with over 90% recovery by utilizing their different grindability characteristics by thermal treatment, semi-autogeneous grinding and screening.

Jan 1, 1999

By Muriel S. Robinette

Ground-water contamination from uranium operations could be avoided with proper site analysis techniques. Contamination from tailings disposal sites is carried downgradient within permeable hydrostratigraphic units which can be located and delineated with a combination of drill holes, borehole geophysical logs and surface geophysics. Several case studies are presented to illustrate this application.

Jan 1, 1980

By Robert R. French

Beneficiation of-low-grade nonmetalliferous mineral deposits by electronic color sorting is currently undergoing a period of rapid development. For those deposits in which the specific gravity, strength, soundness, electric and magnetic properties of the ore and gangue are similar the possibility of separation by color, reflectivity, or fluorescence offers hope for utilization of much poorer quality ore than previously thought possible. For those ores in which consistency of color is required or for which a dry process is preferred, the electronic color sorter is particularly adaptable. Electronic color sorters were first designed to process agricultural products and were small low-capacity units. However, the recent introduction of larger machines designed to process 6-in, diameter ore at a rate of 30 to 50 tph (Anonymous, 1966a), has brought color sorting into the capacity range required by many mineral producers.

Jan 1, 1967

By M. D. Lawton

Anglo-Rouyn Mines Limited, managed by Rio Algom Mines Limited is a subsidiary of the British-based Rio Tinto-Zinc Corporation Limited. This mining operation is situated in Northern Saskatchewan, 250 miles north of Saskatoon and represents the first base-metal mine of any importance served by this relatively new mining province. The outcrop of Copper-bearing Chalcopyrite was first discovered by prospectors in 1915, but was not mined until 1965 due to the absence of any form of road into the area prior to this latter date. The mine, mill and concentrator were designed to handle 900 tons per day of comparatively hard, abrasive ore containing chalcopyrite with traces of gold and silver. The flow sheet, Figure 1, is, we believe, elementary, designed with low cost in mind and utilises much old equipment from closed¬-down mines. Due to some difficulty in attaining the designed grinding capacity, changes were made in the crusher circuit. This, unfortunately, lowered the crushing rate too much. A series of changes have taken place to re-establish the original crusher capacity of better than 100 tons per hour. In the quest for a better recovery certain modifications have been tested in the concentrator circuit. These steps are discussed in minor detail.

Jan 1, 1970

By Hillary W. St. Clair

In a previous report 1/the author showed that the essential information from particle size analyses of grinding mill products can be represented by three or four parameters derived from the first four moments of the particle size data. These parameters may be used in gamma or beta distribution functions to estimate the weight fraction in any given size range. Moment analysis was used to study the progressive changes that take place in particle size distribution when a homogeneous isotropic mineral such as quartz is reduced in size by impact crushing. 2/ This report briefly reviews the essential features of moment analysis and describes extension of this method to size reduction by ball mill grinding.

Jan 1, 1972