Search Documents

By C. Pritchard

John Marks said in his acceptance of the Hartman Award in 2008, “I guess that without the occasional complaint, your mine is probably over-ventilated” (Marks, 2008). Miners are seldom in this situation and spend much of the time trying to find enough air to keep an operation running. With examination, there are usually changes that can be made to increase the efficiency of ventilation systems. Mine ventilation air is a costly commodity, especially by the time it has been heated or cooled and moved to the bottom of the shaft and through the mine airways. Modifications that result in surplus mine ventilation air could bring financial and environmental benefits. Some issues mine operators have needed to address recently are increased airflow requirements to dilute diesel particulates in metal and nonmetal mines, to ventilate reserves that are deeper, hotter, and further away from fans and shafts, and to meet demands from increased production. This paper discusses successful methods to find additional usable air when there is no extra ventilation capacity. Most of the options presented in this paper are useful for metal/ nonmetal operations but some may be applicable to coal as well.

Jan 1, 2009

By Peter Schmäh

Pipe-jacked tunnels are considered for a large variety of applications from water and sewage, cable ducts to challenging pipeline crossings or landfall construction. In most cases, Slurry MTBMs are used to carry out these projects. Continuous further development of technological features for pipe jacking plays a key role to overcome feasibility limits and to meet increased project requirements. As tightened safety regulations in terms of accessibility and escape routes increasingly limit the options of small segment lining tunnels in the diameter range below 4 m, 13 feet, pipe jacking has partially taken over. During the last decades, a growing number of large-diameter and long-distance pipe jacking projects have been completed. Experienced contractors successfully use the technological capacity of the MTBM equipment. The machine and cutting wheel have to be designed according to the ground conditions. Bentonite lubrication and interjacking stations are key factors to keep push forces moderate. For long pipe jacking drives, a so-called push module can be installed in the machine can, to be able to switch from pipe jacking to segment lining in case the machine gets stuck. The overall aim is to provide clients and the tunnel construction industry with safe and economical solu- tions for successful project execution. This presentation will present international milestone projects and will also discuss the latest developments in automation, related opportunities and limitations, and the future of digitization and artificial intelligence in pipe jacking.

Jun 23, 2024

By C. D. Litton, I. E. Perera

This report presents the results of experiments to evaluate different types of mine fire sensors in an underground mine environment using a commercially available atmospheric monitoring system. To determine how well carbon monoxide (CO) and smoke sensors respond for purposes of fire detection, experiments were conducted using test fires of different mine combustibles and for both flaming and nonflaming combustion. The experiments were designed to assess the response of fire sensors to different contaminants and different contaminant levels produced from the test fires. The experiments were performed in the Safety Research Coal Mine at the U.S. National Institute for Occupational Safety and Health’s Bruceton Research Facility in the presence of an average ventilating air velocity of 1.6 m/s (315 fpm). Five fire sensor stations were located downstream of the test fire at fixed locations, with each sensor station consisting of four sensors: a CO fire sensor and three different smoke sensors, of which two were evaluated by the Mine Safety and Health Administration (MSHA) for intrinsic safety and the third was used extensively in underground mines overseas but not evaluated by MSHA for intrinsic safety. All four sensors were mounted near the center of the entry and in the upper onethird of the entry height. A UL-listed combination ionization and photoelectric smoke sensor was mounted near the roof at the first sensor station and its responses were compared against the responses of the four CO and smoke fire sensors. Sensor response data, contaminant travel times, and the impact of fire on the existing ventilation flow are discussed as they apply to earlywarning fire detection. Of significance in the analysis is the need for performance standards for mine fire sensors in order to provide for consistent and timely early warning of developing fires.

Jan 1, 2014

By C. Roos

Traditionally within the mining industry, the main functional process flow for resource and reserve evaluation proceeds from geologists who build the geological model, to resource estimation geologists (modelers) who estimate the grades, to mining engineers who develop the mine design and schedule. The interface between these three disciplines is not always seamless. Assumptions made during one stage of the process are not always communicated down the line, even though most mining companies have procedures in place to encourage communication across the various disciplines. These procedures do not always achieve their aim due to a variety of reasons including time constraints, appropriate people not being available, or a lack of understanding of what other disciplines require, and the handover process can degenerate into one of sending computer files on to the next discipline in the process flow. This paper focuses on the interface between the resource estimation and mine engineering disciplines, and outlines some of the common assumptions made when generating a resource model and the risks that engineers may be taking when elevating cutoff grades, optimizing schedules or generating forecasts. The case studies presented focus on openpit gold deposits, but the concepts should be applicable throughout the industry. A summary of key questions and recommendations is provided.

Jan 1, 2014

By M. Rossi

The use of service variables in geostatistics (grade-thickness) is common in industry when developing block grade models and geologic resource estimates. This is particularly true in the case of sedimentary and strata-bound-type deposits. The approach has proven merits when assessing ore reserves. However, there are cases where its application for preliminary data analysis produces biased estimates. One such case is encountered in uranium disequilibrium studies. This paper demonstrates the inadequacy of service variables when performing uranium disequilibrium studies. Disequilibrium analysis is a necessary pre-processing step when radiation counts are used as raw data to calculate uranium reserves. Typically, a probe is used to obtain the gamma counts from open drill holes. These counts are then regressed (and corrected) against chemical assays obtained from core samples. During this process, the grade-thickness variable produces an optimistic image of the relationship between probe grades and chemical (true) grades, causing overestimation of the final geologic resource. The problem is analyzed through a case study.

Jan 1, 1991

By R. E. Vivas

Goldcorp is one of the largest gold producers in the world with projects in South, Central and North America. Goldcorp?s flagship operation is Peñasquito, a world-class, poly-metallic deposit that started production in 2010 which is one of the largest mines in Mexico. Since the early stages of the project, Goldcorp has used the most advanced technologies available to maximize its value. However, the implementation of optimum mine plans has been challenging to put into practice. This is due to the fact that the mine operation involves more complexity than the plans usually reflect. This challenge is an industry wide issue that presents opportunities for improvement. This technical session discusses the mine planning methodologies and procedures used to connect long, medium and short term planning strategies in order to bridge the gap and produce optimum mine plans that can be practically implemented in the field.

Feb 23, 2014

By Joseph W. Siefke

The Kramer borate deposit is located in the western Mojave Desert at Boron, California, about 100 miles northeast of Los Angeles (Figure 1). The deposit derives its name from the district in which it lies. Borax (Na2 B407.10H2O) is being mined from the Boron open pit to serve a major portion of the United States and world borate markets. This paper deals primarily with those geologic factors which affect slope stability in the overburden at the Boron open pit. Discussion includes slope failure history, slope monitoring techniques and the results of a dipmeter survey of overburden structure. Open pit mining was begun at Boron in 1957. The initial pit was successfully excavated at the recommended 1.5:1 (horizontal to vertical) slope in the overburden. During pit expansion in 1962, excavation of the overburden exposed beds dipping into the pit at +15 degrees and numerous high angle fractures associated with two intersecting fracture systems, the West Jenifer and Portal fault zones. Ensuing south and east wall failures indicated the need for more structural information in the arkose to establish better wall design criteria. Barnard and Kistler (1963) recognized that the many facies changes, faults and other variables in the Boron overburden make it extremely difficult to reduce prediction of slides to a simple arithmetical formula. Despite the difficulties and uncertain¬ties, special programs such as surface resistivity, refraction seismic and core drilling were conducted in an attempt to predict slope stability conditions and to gather geologic information. These early efforts while helpful, did not provide the necessary details of bedding orientations and fault locations which are of paramount importance in our slope stability program. A dipmeter survey in 1974 successfully measured these variables and data from that survey are instrumental in the design of slopes currently being excavated.

Jan 1, 1976

By E. Tarshizi

This research project demonstrates the application of a mine system simulation and animation model in enhancing the efficiency of a truck-shovel operation and reducing the haulage environmental impact in an open-cut coal mine. In any mine, a key objective is to have enough equipment for production and not have excess to where it is counterproductive. Due to the advent of responsible mining, environmental regulations, and eco-friendly practices, these factors must also be considered in the analysis. The over-trucked situation at a mine will be discussed, i.e. when the number of trucks exceeds the optimum number of trucks a mine should have for the most productive/profitable mining operation. When the system has an excess number of trucks, truck utilization is reduced which impacts mine operation, capital costs and the environment, through unnecessary truck purchase, energy use, air pollution etc. A hypothetical surface coal mine layout was used for the simulation model.

Feb 23, 2014

By S. R. S. Sastri, K. K. Bhattacharya, K. S. Narasimhan

Experimental results obtained on the recovery of below 0.5 x 10-3m coal fines by flotation employing geometrically similar columns of 0.056m, 0.080m, 0.100m and 0.220m diameter have been presented. The hydrodynamics of such a unit as well as its performance have been related to operating parameters to establish optimum conditions. The results have further been analysed critically in the light of the known relationship on the behaviour of similar systems to assign reasons for the critical factors established in a bid to reduce the empiricism required to be followed in the scale up of such a unit.

Jan 1, 1988

By Neil D. Donnell, O&apos

Bituminous sands of the Lower Cretaceous McMurray Formation in northern Alberta constitute the ore for the surface mining operation at Syncrude Canada Ltd. These sediments represent a complex succession of fluvial, estuarine and marine depositional environments. Grade prediction is realized through a combination of geological interpretation, computer modeling, and reference to past mining experience. Accurate forecasts of feed grade permit reliable predictions of volumes for removal to meet budgeted synthetic crude oil production. This planning facilitates efficient allocation of mining equipment and resources. The feed grade to the Extraction Plant is monitored at various points along the delivery system.

Jan 1, 1984

By E. DeLilia

For the past 30 years, surface mines have moved toward more highly mechanized, automatic systems that continuously mine overburden and ore to in-crease productivity, lower operating costs and minimize manpower needs. To achieve these goals, mine operators must be involved in every step of the machine procurement process. Several factors are involved in making the machines operate economically and efficiently: ? Prudent engineering. ? Proper planning. ? Realistic feasibility studies. ? Effective specification. ? Thorough training of the mine personnel.

Jan 1, 1995

By David Hatem, Paul Madsen, Daniel Adams, James Morrison, Randall Essex

Managing commercial risks associated with subsurface construction may be the greatest challenge the underground industry faces. The Geotechnical Baseline Report (GBR) was developed in the U.S. to help manage those commercial risks, and to stem increasing litigation in the industry. A guidelines document by the American Society of Civil Engineers was published in 1997 and was updated in 2007. This paper provides an historical perspective, overviews the main objectives of a GBR, presents issues and trends that instigated the need to update the 2007 publication, and describes the process that will lead to a new GBR guidelines publication in 2022

Dec 1, 2022

By Herman Gill, Dani Delaloye, Madelyn Rubin

The Foothill Tunnel is a remote 16-mile-long untreated drinking water tunnel in the San Francisco Public Utilities Commission’s (SFPUC) Hetch Hetchy Water and Power (HHWP) system. The 14-foot horseshoe shaped tunnel, constructed in the 1920s, is lined intermittently with concrete over approximately 53% of its length, with the balance being unlined rock. After detailed planning, in January of 2020 Mott MacDonald and HHWP staff completed a visual inspection and documented the condition of the tunnel with electronic data collection, photographs, and video with audio recording. The result was a comprehensive condition assessment that identified key areas of the tunnel to monitor.

Jun 13, 2021

By K. C. Vories

Surface mining and reclamation has the potential to at least temporarily increase surface runoff and resultant erosion and gully development. This increase in erosion is due in part to compaction of the soil surface with heavy equipment, creation of large relatively unvegetated watersheds, and elimination of natural dendritic ephemeral drainage patterns. Methods for stabilizing gully channels which may develop prior to establishment of sufficient vegetation to control erosion are analyzed. Utilization of various sizes of riprap for channel lining, the use of riprap check dams, reinforcement of riprap check dams, and the relation- ship of type of control structure to area of watershed and resultant flow velocities are discussed.

Jan 1, 1986

By Stanley C. Suboleski

The increase in productivity which has been achieved in mining during the past two decades has been attained largely through the replacement of manpower with electrical power. Power demands should continue to increase, requiring electrical distribution systems to be well planned to avoid inadequate voltage levels caused by underdesign and excessive costs resulting from overdesign. To aid the mining electrical engineer in designing proposed power systems or analyzing changes to existing systems, a digital computer program has been developed. This program will analyze alternating or direct-current networks with up to 10 voltage sources, 75 loads and 300 total segments. A maximum of nine levels of voltage is permitted in the system. This project was part of a package of programs developed at Virginia Polytechnic Institute (WI) for the mining industry under sponsorship of the Office of Coal Research. Included in this package are also programs to: 1. Schedule mine production and predict cost of mining 2. Simulate rail haulage systems 3. Simulate belt haulage systems 4. Analyze ventilation networks 5. Analyze pumping networks These programs are available from the Department of Mining Engineering, VPI, Blacksburg, Virginia 24061 for a nominal processing cost.

Jan 1, 1970

By David J. Brown

Extensive deposits of bituminous, subbituminous, and lignite coals occur in the western United States (Figure 1). Over one trillion tons of identified resources have been located and inferred by geologists and more than 200 million tons of western coal are mined annually (1). In the future, production of western coals will increase significantly and approach national production levels of higher-rank eastern coals. Western coals will be utilized in new power plants as a replacement fuel for oil and gas and may be used in advanced technologies such as diesel engines or in direct-fired turbines. Since these applications require low-ash, low-sulfur coals, crushing to fine sizes and significant cleaning to remove minerals and sulfur will be required. Coal cleaning traditionally has been associated with reducing pyrite and other mineral matter from high-rank eastern coals. To date, insignificant quantities of western coals have been cleaned before utilization and limited data on their washability characteristics exist. Because of this lack of data, it is difficult to predict how these coals will react to standard washing techniques.

Jan 1, 1985

By U. K. Custred

In 1973, the United States production of marketable phosphate rock set a record in excess of 42 million tons. This production rate is expected to continue to increase, due to the growing international requirement for fertilizer, at a rate exceeding 5% per year well into 1977. This trend contrasts sharply with the reduced phosphate rock production levels of the 1966 - 1971 period. The natural consequence of this growing phosphate rock market is an evaluation of the variety of means whereby plant capacity can be most effectively increased. One approach toward increased plant production capacity is through large capacity flotation cells provided they can be successfully applied to the recovery of the relatively coarse product which is characteristic of the phosphate rock feed. This paper will summarize the results of a nine month evaluation test program, conducted at the Haynesworth Mine at Bradley, Florida in which the flotation circuit "specific capacity" (tons feed/ft.2 floor space) and "specific input power" (Hp/ton feed) were determined, and the feasibility of achieving economically acceptable concentrate grade and recovery levels was demonstrated, using large, high capacity, flotation cells.

Jan 1, 1974

By A. M. Raichur

Flocculation of fine coal is usually accomplished with the addition of commercially available organic flocculants. Recently it has been shown that biopolymers derived from microorganisms can be used to flocculate coal. The biopolymers flocculate coal efficiently and render the coal surface hydrophobic. The increase in hydrophobicity can be utilized either to separate the coal flocs from mineral matter. It can also be used for reducing the moisture content of fine coal. In this regard, flocculation and settling tests of fine coal with biopolymers and synthetic flocculants was undertaken and the results are discussed here. Also, a transport model was developed for the time-dependent settling tests for fine coal.

Jan 1, 1996

By J. L. Vanderbeek

The SAG milling of ores with markedly variable grinding rates presents definite process control challenges. Decisions must be made regarding the selection of the most appropriate combination of mill volumetric load level, percent solids, and mill speed for the combination of ore types being processed at the moment. An investigation was performed concerning the effects of these parameters. General results are presented.

Jan 1, 1985

By J. M. Barker

New Mexico is the leading domestic producer of perlite, a hydrated volcanic glass that can be expanded thermally to form a white, very porous, lightweight material. The United States is the leading consumer and producer of perlite in the world (Pettifer 1981). New Mexico produced, at five mines (Fig. 1), about 86% of all domestic crude ore mined in 1984 (Meisinger, 1985). Perlite is mined in 6 other western states, ore is expanded in 33 states, and the expanded ore is consumed in all states (Meisinger, 1985). Gross value of domestic ore mined in 1984 was about $16,500,000 (FOB mine; Meisinger, 1985) with much value added by expansion and processing prior to sale to end users. In contrast to the ubiquitous nature of perlite products in the U.S. economy, facilities for testing perlite ore, expanded perlite, and perlite products are notably lacking on a commercial, cost-effective, or readily accessible basis. The New Mexico Bureau of Mines and Min¬eral Resources (NMBM&MR) established a perlite¬testing facility in 1984 to mitigate this lack and to further the mining of perlite in the state.

Jan 1, 1985