Search Documents

By R. Thorpe, M. Dosbaba, A. Kopriva, A. Niiranen, J. Ruokanen

"Automated Mineralogy (AM) is an important diagnostic tool in flotation plants as it adds ore and particle mineralogical properties to traditional mass and chemical data. AM is used in project development, for future ore studies and for diagnosing concentrator operations. With the exception of operations who own central laboratory or on-site systems, the use of AM is often limited to the analysis of a comparatively small set of samples. Metrix Plant Technologies has partnered with TESCAN to integrate TIMA AM technology into the implementation of Performance Assessment Campaigns (PAC). Routine daily composite samples from the mill are analysed mineralogically on a size-by-size basis over several weeks. All the relevant metallurgical, process control and mineralogical data is combined into a single large database for mass balancing and interactive examination. This paper describes the implementation and results of a PAC at the Agnico Eagle Kittilä gold mine in Finland. Although challenging, the addition of mineralogical data as dependent variables in multivariate analysis leads to a much deeper understanding of the root cause effect of events driving the flotation performance. INTRODUCTION TO STUDY The Kittilä mine, owned by Agnico Eagle, is Europe’s largest primary gold mine, with annual production of approximately 180,000 Oz. The operation is located in Lapland in northern Finland, and is currently expected to operate until 2035. The location of the operation is shown in Figure 1. Historically, the mine was an open pit, although in recent years ore is sourced solely from underground operations. The processing plant features crushing and grinding, followed by carbon flotation and sulphide flotation. Carbon concentrate is a waste stream, and sulphide concentrate reports to pressure oxidation (autoclave) and CIL circuits for gold extraction. The final flowsheet is shown in Figure 2. Following commissioning in late 2008, the operation achieved commercial production on May 1st 2009. Gold recovery in flotation gradually increased to a 92-96% range at a throughput of ~3500-4000 tonnes per day. In late 2014, the operation commissioned a plant expansion to ~5000 tonnes per day. Following a commissioning period, the operation stabilised with recoveries in a 90-94% range, which over any given period was determined to be ~2% lower with statistical significance. The trends from start-up of gold recovery in flotation and throughput are shown as follows in Figure 3. In early 2016, Agnico Eagle Kittilä mine, along with Agnico Eagle Technical Services (AETS) partnered with Metrix Plant Technologies and TESCAN, to perform a Performance Assessment Campaign (PAC) at Kittilä, involving automated mineralogy on five key streams at Kittilä on 40 days selected from a 50 day period between February 15th and April 4th 2016, when plant operations were stable. In addition to the mineralogical data, metallurgical and operational data were pooled into a single, powerful database to explore opportunities for the operation to improve recovery in a sustained manner, ideally to the levels pre-expansion."

Jan 1, 2017

By H. Maleki

This paper recognizes the 100th year of research accomplishments by the mining industry resulting from close cooperation among mining companies, geotechnical consultants and researchers from the former United States Bureau of Mines in stability assessments and development of improved and productive mine designs. The paper provides an overview of dramatic developments in geotechnical instrumentation, and its applications in the U.S. and around the world for enhancing the understanding of ground response to mining-induced changes in stress, resulting in improvements in ground control technologies.

Jan 1, 2010

By N. T. Rogers

An accepted statement of fact is that transportation next to agriculture is the second most important industry in the world. The transportation networks of the United States contributed immensely to the growth and prosperity of our nation. My objective is to make each and everyone here aware of the need for communication between geologists, mining engineers, purchasing agents and transportation managers. Only through a cooperative effort is it possible to reap the benefits of transportation in the industrial minerals field. Transportation is often thought of in terms of trucks, rail cars, barges, covered wagons or whatever. If this is your only exposure to the transportation industry then you probably spent most of your life in a cave.

Jan 1, 1989

By Dan S. Nilsson

When an open pit mine is deepened, more and more waste rock must normally be removed. Techniques for optimization of open pit design are well-established within the mining industry. The recommended method is to choose the open pit alternative with the highest net present capital value of open pit and future underground mining. When the open pit is mined out, the operation must be closed, or, if it is profitable, mining must start underground. When planning an underground operation we experience the same type of optimization problem that occurs when determining the optimal depth for open pit mining. When mining underground the ore body is often divided into a number of areas, blocks or slices, each containing a transportation system with trains, trucks, conveyors, etc. When all the ore within such a part of the deposit is extracted, the operation must be closed, or, if it is profitable, a new transportation must be developed. The question that now arises is: how large a pan of a deposit shall be included in the first development and how much shall be left for future consideration?

Jan 1, 1981

By M. Sears, G. S. Esterhuizen, Z. Khademian

According to the 2010-2019 Mine Safety and Health Administration (MSHA) accident report database, 91% of reported ground control accidents in U.S. longwall mines were caused by roof instability. Gateroads are subject to significant changes in loading conditions from the development to the longwall abutment loading phases. When combined with thinly bedded shale roof, found in many U.S. longwall coal mines, the design of efficient roof support becomes challenging. In previous work, the Bonded Block Method (BBM) modeling of roof by UDEC was validated against field extensometer measurements in a longwall gateroad entry roof at a 180-m depth of cover. The BBM was shown as capable of capturing delamination and buckling of shale roof, one of the main roof instability mechanisms in longwall mines. This paper presents the recent findings on the roof-support interaction using BBM models of the same longwall entry. The effects of cable bolts, roof bolt density, and strap support on potential roof instability are studied. These types of studies are difficult and costly to conduct in an operating mine. Results show how the contribution of bolts, straps, and cable bolts can be quantified using the BBM models. The study demonstrates the potential for BBM numerical models to help understand the complex roof and support system interactions and to assist with optimizing gateroad support systems.

Feb 1, 2023

By Kadri Dagdelen, Lee J. Zamalloa

Modern surface mining operations are always seeking for minimizing costs while increasing production rates, among the optimization of other specific tasks that have an impact on the economics of the mine. Specifically, the cost related to the production fleet operation (shovels and trucks), the maximization of the overall performance of the equipment, and the uncertainty to meet the goals at the end of the operational time horizon are always topics of discussion with no apparent simple answer. On the other hand, truck-shovel dispatch systems based on Linear/Non-Linear Programming Algorithms have been in operation since mid-1990’s with different levels of success depending on the correct arrangement of operational resources and the complexity of the mine, but having in most cases some important shortcomings related to the way these systems deal with the decision making of the operational objectives, being necessary to have a human agent (dispatcher) to guide the system when the operational parameters change, creating the possibility of suboptimal decisions due to the human factor. This paper discusses the implementation of a novel methodology based on AI techniques to assist in the decision making of the best goal selection when operating a Fleet Management System, taking into consideration time periods as variables and integrating them as part of the analysis, providing a better overview of the forecast plan completion with respect to previous production numbers and evaluating best alternative to handle future events to minimize losses or maximize profits, resulting in better truck assignments, minimum shovel idle times and overall productivity improvements of the operation at the end of the time horizon.

Jun 25, 2023

By M. E. Rossi

Reconciliation of long-term block model reserves and mine production frequently shows significant discrepancies. This reconciliation can be done comparing the long-term block model reserves against a grade control model (generally, a model based on blast holes or production data). in this paper called an FI factor for tonnages, grade, and ounces; and also it should be done comparing the grade control model to the mill feed (or loaded to heaps) tonnages, grades and ounces (called an F2 factor). The long-term model usually contains blocks with dimensions larger than the size of the selective mining unit (SMU) of the operation. The smoothing effect of an estimator such as kriging will generally result in a grade-tonnage curve that does not match the grade-tonnage curve of the SMU's to be recovered. This problem is partly to blame for the reconciliation discrepancies found. In addition, in-pit perfect selection is impossible. and therefore the grade-tonnage predictions based on blast holes also need to be assessed, considering both unplanned dilution and the errors of estimation of the grade control model. This paper will focus on using conditional simulations to assess the uncertainty of the predicted grade-tonnage curve in terms of minable reserves, and in the framework of long-term mine planning. Quantifying the uncertainty in no uncertain terms is done in conjunction with a popular pit optimizer, which will yield not one, but several possible minable reserves, and therefore a range of possible minable tonnages and grades per pit shell or scheduled phase. This is a step further from the usual sensitivity analyses that are performed for deposit evaluation or development planning. Specifically, this approach takes into account the volume-variance relationship, the selectivity of the mining operation, planned and unplanned dilution. and carries the local uncertainty implicit in grade estimation into the mine design and mine planning phases. The motivation for the approach is discussed through an example, as well as a description of the procedures and steps involved.

Jan 1, 1998

By James Charles McHardy

During 1980-2000, the Florida Phosphate industry will deplete its Central Florida Polk County reserves. As a result, new mines will be built in the ?so-called? Southern Florida Reserve areas. These new mines will require new mining, beneficiation and tailings disposal technologies in that the southern reserves have different characteristics than have been encountered in the Central Florida deposits furthermore, government regulations will necessitate the development of new tailings and clay disposal methods. This paper reviews these challenges for the phosphate industry and how these opportunities can be expected to effect plant design and plant operating practices.

Jan 1, 1981

By Alain A. Sonntag

The MBS Solvent Extraction System utilises a unique design of mixer- settler having very high capacity per unit area and great flexibility. The development of the mixer-settler is traced through its various stages wherein the independence of mixing and pumping, reduction in settler area requirements and simplicity of plant layout were achieved. The laboratory, pilot plant and full scale tests contributing to the development of the machine are described. The existing KREBS SX plants in Europe and Africa are described as well as the plants presently under design. Results of recent testwork are also given.

Jan 1, 1981

By L. A. Khan

This paper first discusses the physicochemical cleaning methods used to process fines followed by an analysis of the subprocesses of froth flotation and the adverse effects of slimes and particle oxidation. These subprocesses include the phenomena of interception, contact, adhesion and levitation. Preventive and corrective measures to combat the generation of fines and their effects are suggested. Preventive measures include controlled grinding, limited liberation, flotation at coarser sizes. Means of preventing oxidation and/or removing oxidation products are a1 so discussed. Corrective measure to increase recovery include intensive aeration, aggregation of particles, intensive mixing, increased retention time, and reduction of detachment. Measures leading to improves selectivity involve means to reduce slime coating, achieve selective mineralization of bubbles and minimize entrapment.

Jan 1, 1986

By S. Makni, R. E. McIvor

Grate discharges historically outnumbered the overflow type of industrial wet ball mills. However, overflow discharge mills now strongly dominate. In order to understand their comparative advantages and disadvantages, Corem carried out a broad review of this topic. Where the data made it possible, the Functional Performance Equation was used to separate circuit classification from mill grinding effects. Batch tests were conducted in a torque-metered mill at different slurry levels. This paper presents the outcome of these investigations, which is a very strong case for the industry to once again consider grate discharges.

Feb 1, 2023

By Jamal Rostami, Tala Tahernia

TBM utilization rate is a component of machine performance prediction and critical for developing a reliable estimate of the construction completion time and cost of the tunnel. Estimation of the utilization rate involves identifying and quantifying the time dedicated to each activity in a tunneling jobsite. Ring building is a common activity in TBM tunneling and takes a large amount of tunnel excavation time when using shielded TBMs. This paper concentrates on the effect of tunnel diameter on the duration of downtimes related to ring building and examines the impact of machine diameter on downtimes. For this purpose, the dependency of segment installation time to segment configuration, and also the diameter of the tunnel was investigated. Furthermore, the ring building time for four tunnels with different sizes of diameters and a variety of ring arrangement were analyzed and the relationship between TBM diameter and segment installation time and consequently TBM utilization was evaluated.

Jun 13, 2021

By V. D. Smar

The flotation process may be considered an interactive system consisting of many chemical, operational, and equipment variables. Changing anyone of these variables causes an overall system response change. This study examines the effects of simultaneously changing the operating variables of: (1) frother concentration and air flow rate, and (2) frother concentration and collector concentration. It is part of a comprehensive study to look at how changes in several of the major variables may be used to produce interactions which will allow the rougher flotation process to be optimized. Ultimate recovery, flotation rate, concentrate grade and froth quality, are used as the major evaluative criteria.

Jan 1, 1993

By Daniel B. Brimhall

The research presented here was initiated to investigate the role of atmospheric oxygen in the leaching of copper waste dumps. The problem of increasing the recovery rate of copper from these dumps is or great importance considering there are by conservative estimate in excess of fifteen billion pounds of copper located in dumps in the western United States. At this time, there is an increased interest in recovering copper from these dumps on a large scale. Large tonnages of low-grade material are being placed on the waste dumps of most copper mining operations in the western United States each day. The size of these dumps ranges from 5.5 million tons at Mineral Park, Arizona, to 4 billion tons at Kennecott's Utah operation (1). Leach solutions are recycled and contain ferrous and ferric sulfates. Large quantities of dissolved aluminum, magnesium and calcium salts may also be present. To this solution make up water is added to maintain the solution inventory and sulfuric acid is added for pH adjustment. Iron is introduced into the leach solution by the dissolution of the iron-containing sulfide and oxidized minerals present in the ore deposit. In addition to the iron from dump leaching, iron is also introduced during the precipitation process when the pregnant solution is passed over metallic scrap iron if cementation is used to reduce the copper in solution.

Jan 1, 1972

By Allan M. Hale

Taconite tailings reclamation, especially the stabilization of tailings ponds, .dams, and slopes, can be effectively accomplished through the use of appropriate vegetation. Utilizing vegetation provides both aesthetic and ecological enhancement of a site while at the same time protecting tailings structures against wind and water erosion. Generally, the methods and techniques for establishing vegetation are well known; however, there are many site-specific factors that can alter a particular reclamation approach. Those factors include slope gradient, tailings material size, solar exposure, and physical and chemical properties of tailings. In addition to the site-specific factors, variations in climate, geography, and physiography of a region can have a pervasive influence on the success or failure of a revegetation program. Both the site-specific and regional factors control reclamation planning in such areas as plant variety selection, methods and times of plants establishment, maintenance techniques, and subsequent monitoring methods. As a result of this multifactor relationship, it is important to establish a data base that identifies both the site-specific and location conditions in order to tailor the reclamation plan to the specific area. When an appropriate data base has been collected, detailing the various site-specific and regional factors that will influence a revegetation program (in the absence of previous testing), it is very beneficial to apply experimental techniques to develop the reclamation plan for a specific site. The reclamation plan for a specific site may include several techniques adapted for the differences found within the specific site as the result of topographic or other influences. Considering this, the Reserve Mining Company and Dames & Moore undertook to develop a successful reclamation plan based on a detailed test plot program conducted at the Mile Post 7 location.

Jan 1, 1980

By R. G. Reddy

Spent potliner is generated in the electrolytic process of reducing alumina to make aluminum metal using molten fluoride electrolytes. Spent potliner (SPL), obtained at the end of the pots life contains a small amount of cyanide and fluoride which present environmental problems. SPL became a listed hazardous waste under RCRA (K088) in July, 1990. One of the possible uses of spent potliner is as a substitute for Calcium Fluoride (CaF2) as a fluidizer in iron-and steel making and in the glass industry. A low viscosity and a low melting point are prime requirements for accomplishing the above. In the present study, viscosity measurements were performed. Effect of various additives, such as sand, limestone, dicalcium silicate dust, and MgO baghouse dust on the viscosity of SPL was studied. The results showed that with the addition of sand and limestone, very high fluidity of SPL melt can be obtained at significantly low temperatures. The results suggest that spent potliner mixed with additives could potentially be used as a substitute fluidizer.

Jan 1, 1999

By F. Cappel

Except in a few special cases, it is necessary for solid fuel direct reduction in rotary kilns that iron-bearing materials be charged with a minimum grainsize of approx. 5 mm. For fines not usable in such form, the combination of sintering - as agglomeration step - and direct reduction were investigated. During reduction of sinter in rotary kilns prevail dependencies on sinter quality and varying reaction parameters, owing to the use of different coals, which led to a definite statement as to what quality sinter must have and which coals can be used.

Jan 1, 1983

By P. C. Thakur

Methane has been a hazard since the beginning of coal mining and has influenced, more or less, every aspect of coal mine design. It is receiving increased attention lately because the rate of methane emission in coal mines is increasing as increasing demand for coal leads to exploitation of deeper seams and the use of higher productivity equipment. Consequently, the government and private industries have directed a great deal of effort towards understanding and solving the problem of methane emission in coal mines. In the United States, Consolidation Coal Company has pioneered research in this area since the early 1950's.1 Currently this work is being expanded by Consol through the Mining Research Division of the parent company, Continental Oil (Conoca), to find new techniques for degasification of virgin areas as well as control of methane in gob areas. Basic reservoir properties of coal seams, such as gas content, reservoir pres-sure, diffusivity, porosity and permeability are better understood today largely through the efforts of the U. S. Bureau of Minese2,3,4 It is possible now to identify and model the basic mechanism of gas emission from coal and to forecast steady as well as unsteady state emission of methane in coal mines with some degree of reliability. Combining this knowledge with any ventilation simulator should often identify problem areas in advance and permit adequate methane control measures to be planned.5 Another recent innovation in methane control is the horizontal hole drilling technology. The U. S. Bureau of 1-1ines and the Mining Research Division of Conoco have independently developed techniques for drilling horizontal holes 300 to 600 m deep6 The Bureau's method employs a rotary drill string while Conoco uses a non-rotating string with a down hole drill motor. It is the authors' view that the latter provides more positive control on bore hole deviation both vertically and laterally and appears to be faster, though somewhat more difficult to operate. The rate of methane emission depends on a number of factors which can be broadly classified in two groups. These are (1) the basic reservoir properties of

Jan 1, 1977

By S. K. Ghosh

This paper discusses how the information on ash composition, ash-fusion temperatures, and ash-slag viscosity can be utilized to predict slagging and fouling potentials of a particular coal. A review of several empirical parameters which are commonly in use for determining such potentials is given. Also, some guideline values for interpreting the relative propensity of slagging and fouling of various types of coal are provided.

Jan 1, 1983

By M. J. Sanzotti

This paper examines the potential for controlling longwall-induced subsidence by pneumatically backstowing the void created by mining with waste rock, and having the process scheduled as a unit operation of the mining activity. Based on a review of background literature, interviews with representatives of various mining companies, public-interest groups, and state and federal regulatory agencies, a hypothetical case-study evaluation of pneumatic stowing in a southwestern Pennsylvania mine site was conducted. The study indicated that current stowing technology cannot keep pace with the production potential of U.S. longwall systems. Further, at the case-study mine site, concomitant stowing would reduce subsidence by only 50% of that incurred during full longwall caving, the longwall coal production rate would decrease from 4000 tons per shift in the non-stowing case to 1500 tons in the stowing case, and a preliminary cost analysis reveals that pneumatic stowing would add $5.25 to $10.50 to the operating cost of producing a ton of coal at the case-study site.

Jan 1, 1995