Search Documents

By Sai Phaninder Reddy Chaganti, Corrina D. Beaven

This study investigates the effect of reagent type, dosage, and pH on flotation kinetics and copper recovery for secondary sulfide ore with elevated clay content. The primary objective was to determine whether Xanthate performs comparably to or better than the currently used primary collector, Thiophosphate. Approximately 80 kg of ore was collected from three blast holes and systematically prepared through drying, crushing, grinding, and flotation testing. Grinding tests were conducted to establish optimal grinding time and lime consumption for pH control, achieving a target particle size distribution in 13 minutes and 30 seconds. Elemental and mineralogical analyses using X-ray Fluorescence (XRF) and X-ray Diffraction (XRD) identified a copper content of 0.36% and significant clay presence, affecting flotation performance. Fifteen flotation tests were performed under controlled conditions, with variations in reagent dosages. Control tests confirmed reproducibility, with recoveries around 80–82%. Increasing the pH did not improve kinetics or recovery, making higher pH adjustments economically unjustifiable. Adjusting the Thiophosphate dosage yielded the best recovery of 83%. Xanthate collectors, tested both as tertiary additives and as replacements for Thiophosphate, delivered comparable or superior recoveries—up to 91.5% in plant tests—and demonstrated faster flotation kinetics, even under high-clay conditions. These findings highlight Xanthate’s reduced sensitivity to clay, potential for lower dosage requirements, and operational benefits such as improved selectivity and circuit efficiency, validating its role as a cost-effective and alternative for processing complex sulfide ores.

Feb 22, 2026

By N. Arbiter

Fracture under low velocity free-fall and double impact, and under slow compression have been-investigated. The pattern of breakage and the size distribution of resulting fragments for sand-cement and glass spheres have been determined. Photoelasticity methods were used to simulate the stress distributions in free-fall impact in order to explain the observed patterns of breakage. Oblique fracture planes, occurring only in free-fall impact, develop along lines which coincide with the trajectories of principal compression as determined by mathematical analysis Breakage efficiencies for different modes of fracture were compared for both types of spheres. For the same specimen and loading system, static loading and low velocity dynamic loading induce geometrically similar stress fields resulting in reasonably similar fracture patterns and shapes of fragments.

Jan 1, 1968

By Roussos Dimitrakopoulos, Liam Findlay

Semimobile in-pit crushing and conveying (IPCC) systems can help reduce truck haulage in openpit mines by bringing the crusher closer to the excavation areas. Optimizing a production schedule with semimobile IPCC requires integrating extraction sequence, destination policy, crusher relocation, conveyor layout and truck fleet investment decisions. A mining complex with multiple mines and IPCC systems should be optimized simultaneously to find an optimal schedule for the entire value chain. An integrated stochastic optimization framework is proposed to produce long-term production schedules for mining complexes using multiple semimobile IPCC systems. The optimization model has flexibility to select the crusher locations and conveyor routes from anywhere inside the pits. The framework uses simulated orebody realizations to consider multielement grade uncertainty and manage associated risk. A hybrid metaheuristic solution approach based on simulated annealing and evolutionary algorithms is implemented. The method is demonstrated using an iron ore mining complex

Nov 1, 2024

By V. Rajaram

R.C. Rex, Jr. V. Rajaram's paper does not accurately reflect the status of Eastern oil shale development as it stands today. Today, there are numerous firms and research organizations pursuing development of the Eastern oil shale resource. Details of the current projects can be found in the symposium proceedings for the 1985 Eastern Oil Shale Symposium held in Lexington, KY, in November 1985. Additionally, the comparison of the Paraho and HYTORT processes is invalid because the HYTORT process design used it not an accurate representation of the HYTORT process. I will briefly address this point. It is disconcerting to see the author reference hydroretorting work conducted at the Institute of Gas Technology (IGT) (circa 1978) in the introduction, which indicates hydroretorting (the HYTORT process concept) yields of up to 250% of the Fischer Assay oil yield, and then turn around and base the remainder of the paper on the 1981 "Synthetic Fuels From Eastern Oil Shale Report," which depicts the HYTORT process as yielding only 115% of Fischer Assay. Indeed, work conducted at IGT to 1981 indicates commercial oil yields for the HYTORT process would be in the range of 200% to 210% of Fischer Assay. A more thorough literature search by the author would have yielded a 1981 publication by Schora et al., entitled "Update on the HYTORT Process" presented at the Symposium on Synthetic Fuels From Oil Shale in Nashville, TN, October 1981. This paper thoroughly discusses the shortcomings of the referenced study with respect to the HYTORT process. For the interested reader, I can also recommend a June 1984 report entitled "An Economic Comparison of Five Process Concepts for Using Eastern Oil Shale," published by Los Alomos National Laboratory (LA-10106-MS, Parkinson et al., NTIS No. DE84-015981). This study applies a realistic HYTORT design (circa 1982) and indicates that HYTORT is the most econom¬ical method of processing Eastern oil shales (about $20/bbl less than Paraho). Additionally, completion of the HYTORT feasibility study in June 1983 by Phillips Petroleum Co., Bechtel Group Inc., HYCRUDE Corp., and IGT has resulted in development of designs that will make the use of HYTORT on Eastern oil shales even more economic. HYCRUDE Corp., a second-tier subsidiary of IGT, is involved in commercialization and licensing of the HYTORT process and is active in efforts to develop the Eastern oil shale resource. As such, I am disappointed to see outdated material that has the potential for adversely affecting development of Eastern oil shale resources published in MINING ENGINEERING. I can only hope that this response will serve to mitigate any negative opinions that may have been formed. Today, activity in commercializing Eastern oil shales dominates the oil shale scene in the US and indicates a realization of the potential for these shales. Reply by V. Rajaram I appreciate the updates on the HYTORT process provided by R.C. Rex, Jr. I hope that Hycrude's work will lead to the funding of a pilot plant to demonstrate that yields of greater than 200% of Fischer Assay can be achieved in a commercial plant using eastern US oil shales.

Jan 9, 1986

"In the conceptual stages of engineering, benchmarking and empirical ratios are commonly the only references for estimating the production rate of greenfield projects. For underground mining projects, the lack of similar cases often makes the comparison difficult due to each project’s unique geology, rock quality or other singular characteristic. This paper discusses an analytical alternative for determining the maximum achievable production rate for underground stoping mining by modeling production as a continuous process. The results show that long-term maximum capacity depends exclusively on the achievable development rate and the development intensity of the design. In operations constrained by backfill, the development rate could be limited by the backfilling rate. Extraction rate and stope size only have impacts on capacity estimates during the ramp-up period.These findings allow shaping of the maximum capacity profile of a project. They can be used as a tool for quick assessment of conceptual capacities, and sensitivities of mining rates. Benchmarking tests compared favorably with projects, mines in operation and scheduling exercises. IntroductionA key consideration in the value proposition of a mining project is its capacity or production rate (Tatman, 2001). At a conceptual level, it is common practice to refer to empirical references (Taylor, 1986; Long, 2009), rules of thumb (de la Vergne, 2014), benchmark ing studies or consultant experience to estimate or validate a target value. There is, however, a lack of analytical methodology to guide an early estimate of the maximum capacity.Araneda and Gaete (2004) presented an interesting mathematical approach to estimate the capacity of panel caving mines. Using a continuous model, they confirmed that the mine capacity is essentially determined by the rate of area incorporation, in terms of area per period, and ore column height. This simple relationship has been confirmed by multiple detailed scheduling works"

May 1, 2016

By S. S. Peng

The generation and transportation of the airborne dust are mainly governed by the velocity and the movement pattern of the ventilation air in the longwall face. Generally speaking, the higher the air velocity, the more the airborne dust will be generated and the longer the period of the dust of certain size will be carried away from the source. In order to effectively prevent the production and the spread of the airborne dust, The airborne dust concentration distribution in the longwall face must be known in advance. Before the dust concentration distribution can he predicted theoretically with confidence, the air velocity distribution pattern of the ventilation air in the longwall face area must be determined first. However, the complicated, time-dependent and unpredictable mining conditions along and around the face area make the theoretical studies of the problem rather difficult. For instance, one of the factors commonly affecting the air velocity distribution at the longwall face is the air leakage, either into or from the gob area. The leakage quantity and the location of occurrence differ from mine to mine, face to face, and time to time. They depend not only on the compactness of the caved roof fragments in the gob, but also on the degree of obstructions in the working space and in the return entry. Another obstacle to the theoretical studies about the velocity distrbution is the complicated boundary conditions of the ventilated spnce which is very difficult to represent accurately in mathematical forms. In this paper, the air velocity distributions measured in four longwall faces are presented. A statistical model for each longwall face is also derived for prediction of air velocity distribution in the longwall face.

Jan 1, 1985

By J. Alatalo

Autogenous grinding is a process of reducing the particle size distribution of an extracted ore by using the ore itself as the grinding media. It is a process that is difficult to control and there is a lack of knowledge of the events occurring inside the mill. To find out more about how the mill behaves under different processing conditions, a full factorial test was performed with iron ore in a pilot-scale pebble mill at the LKAB R&D facility in Malmberget. To complement this work, a strain gauge detector was embedded in one of the mill?s rubber lifters, the Metso Minerals continuous charge measurement (CCM) system, and was used to get more information about the charge dynamics. The data from the experiments has been analyzed. For production purposes, an increase in the number of particles smaller than 45 µm can be regarded as a probable increase in the production rate. The analysis shows that there will be an increase in fines at 65% of critical speed, especially when the mill is 45% full. This setting will also increase the power consumption, but improves the grindability of the ore even more. The deflection of the lifters is smaller for lower critical speeds. A higher degree of filling also gives a smaller toe angle and a higher shoulder angle as expected.

Nov 1, 2011

By Immo H. Redeker

The Kings Mountain area of North Carolina is the lithium pegmatite center of the U.S., if not of the whole world. We have two spodumene and by-product mineral producing companies, Lithium Corp. of America, and Foote Mineral Company. We also have Kings Mountain Mica and Kings Mountain Silica Companies producing mica. feldspar, quartz and clay from weathered pegmatites in that area. Figure 1 gives the location of the spodumene pegmatite area in North Carolina. The two spodumene producers mine typical pegmatite ore in open pits after removing amphibolite or mica schist overburden which is sold to aggregate producers. The ore reserves are discussed elsewhere in this session. They are in the order of plus 50 million tons but not unlimited. 1.2 The major minerals found and concentrated from the North Carolina spodumene pegmatite ores are tabulated on Table 1.

Jan 1, 1977

By J. Alatalo

Autogenous grinding is a process of reducing the particle size distribution of an extracted ore by using the ore itself as the grinding media. It is a process that is difficult to control and there is a lack of knowledge of the events occurring inside the mill. To find out more about how the mill behaves under different processing conditions, a full factorial test was performed with iron ore in a pilot-scale pebble mill at the LKAB R&D facility in Malmberget. To complement this work, a strain gauge detector was embedded in one of the mill?s rubber lifters, the Metso Minerals continuous charge measurement (CCM) system, and was used to get more information about the charge dynamics. The data from the experiments has been analyzed. For production purposes, an increase in the number of particles smaller than 45 µm can be regarded as a probable increase in the production rate. The analysis shows that there will be an increase in fines at 65% of critical speed, especially when the mill is 45% full. This setting will also increase the power consumption, but improves the grindability of the ore even more. The deflection of the lifters is smaller for lower critical speeds. A higher degree of filling also gives a smaller toe angle and a higher shoulder angle as expected.

Jan 1, 2011

In the last four years, 2007~2010, 9 out of 24 metal/nonmetal underground mine fatalities were caused by ground fall across United States of America (Mine Safety & Health Administration, MSHA). To reduce or eliminate incidents/accidents caused by ground fall, this paper clarified how to design and select ground support based on different ground conditions, how to use mine ground support standards, what geotechnical engineers and underground operators should do to keep mine production free of ground failures.

Jan 1, 2012

By A. W. Khair

This paper presents a strength formula for the design of coal pillars. The formula is derived from results of laboratory experiments, studying the effects of primary factors influencing the strength of the coal specimens/pillars. Five primary factors, significantly affecting the strength characteristics of the coal specimens/pillars were identified and extensive laboratory investigations were carried out. The five primary factors were namely 1) coefficient of friction between loading platens and coal specimens, 2) elastic properties of the loading platens, 3) coal specimen geometry, 4) coal specimen size, and 5) rate of loading. Four to nine levels of variation for each primary factor on the strength of coal were studied. An empirical formula, implementing the variation of the primary factors affecting the strength of coal specimens/pillars, has been developed. A comparative analysis of the results provided by this and some well known formulae is also presented.

Jan 1, 1994

By N. Moelans, I. Bellemans, K. Verbeken

Metallic droplets can remain attached to solid particles within liquid slags, resulting in production losses in several movement of solid particles in the liquid slag in a system, considering the attachment of liquid metal droplets to solid slag and on the resulting microstructures is investigated as a function of the velocity of the particles. For all wetting For the amount of metal attached to the particle, a clear trade-off was found between the speed of motion of the solid particle and the wetting regime.

By W. H. W. Husband

Rock salt has been mined by the solution method for many years in many countries. Attempts have been made in the past in Canada and various other countries to produce potash by the' same method. However, only Kalium Chemicals Limited (1) has been successful, possibly because the conditions in Saskatchewan are the most favorable conditions to be found so far for the development of a solution mining method for potash. There are significant differences in solution mining of rock salt and solution mining of potash. First, rock salt deposits are relatively pure in respect to soluble minerals, whereas potash is never found in the pure state and contains Substantial amounts of other soluble minerals, particularly rock salt. In comparison to rock salt, much less potash is dissolved and brought to the surface for the same amount of water circulated through the orebody. The amount of water to be evaporated per unit weight of product is a major difference. Much greater amounts of water must be evaporated when producing potash and the treatment of the brine is more complicated because other dissolved salts have to be separated. Secondly, the rock salt deposits, particularly the domes, are much thicker. Bed thickness is of prime importance because it determines the yield of a well and consequently the economics of the process. Furthermore, as rock salt provides a strong roof structure, larger cavities can be developed and this prolongs the life of the rock salt well.

Jan 1, 1971

By Charles T. Holland

The tonnage produced on mechanized automated retreating longwall faces in the United States is growing rapidly. This time last year some 14 faces were operating, and in addition to that, three were known to be down looking towards revision or repairs before being placed back in service. These, it is believed, are now in service. It is estimated at the present time, therefore, that somewhere between 20 and 25 faces are being operated in the country. A survey made last year by the School of Mines, West Virginia University, indicated that longwall mining in general has been beset with a great many problems, some more serious than others. The problems that we propose to discuss here are those pertaining to roof and floor trouble in the tailgates. Longwalls are operating in this country at the present time under an overburden ranging from 200 feet to nearly 3000 feet. Main and tailgate entries are operating in panels of up to five each, with the width of the pillars between these entries varying from 20 to 50 feet. Face lengths are running from 270 feet to 670; actually a face 800 feet long should be possible. The most economical face is often spoken of as being around 450 feet.

Jan 1, 1969

By Richard P. Stahura

During the next five years, there will be a trend toward performing belt cleaner maintenance while the conveyor is in operation. Most mines and industrial sites that use belt conveyors have an in-house safety rule that the belt must be stopped before maintenance work can be performed on any belt-cleaning device. This is a good rule. Most cleaning devices are positioned against the belt with hardware that requires the service technician to reach or climb into the chute to change the cleaning blades. But this simple rule becomes more complicated as production demands require higher conveyor availability and provide fewer conveyor outages. In many cases, today’s conveyors are expected to be available 98% to100% of the time.

Jan 1, 1996

By F. A. Schinner

The present study has investigated the leachability of cadmium sulfide minerals by Thiobacillus ferrooxidans and the electrochemical reactions involved in the process. Using a cyclic voltammetric technic and carbon-paste-CdS electrodes, it was found that the bio-oxidation of semiconductor cadmium sulfide minerals consisted of a number of intermediate electrochemical reactions. The overall reaction was found to be controlled by solid state diffusion as suggested by the chrono-amperometric and chrono-potentiometric measurements. The activation energy of solid state diffusion was determined by the Sand's method to be AE=24.3 kJ. A generalized mechanism was proposed for the bacterial oxidation of cadmium sulfide by T. ferrooxidan and an explanation given for the importance of high redox potential of leach solution versus the decomposition potential of the sulfide mineral. Furthermore, the effects of n-type or p-type character of CdS substrates relative to their bioleachability was discussed.

Jan 1, 1993

By Serhat Özdemir, Derya Öz Aksoy, Pınar Aytar Çelik, Ahmet Çabuk, Sabiha Koca, Hüseyin Koca

In carbonate flotation, oleate has been used for many years as a collector in industrial scale. Compared to sulfide minerals, the flotation of carbonate minerals requires more collector consumption and has lower yield and selectivity. It has been previously shown that surfactin provides higher yields in smaller amounts than oleate in the bioflotation of calcite as one of the carbonate minerals. In this study, the usability of surfactin as a flotation collector for magnesite was investigated. For this purpose, the adsorption of surfactin on the magnesite surface was inspected with analyses such as FTIR, SEM–EDS, contact angle, and zeta potential measurements. In addition, the effect of surfactin on the surface tension of water was also revealed. The same analyses were also performed for oleate as a reference point. All flotation experiments were performed without optimizing with both collectors. FTIR results showed that the surfactin, like oleate, was chemically adsorbed on the magnesite surface. Surface tension analyses showed that the surface tension of water decreased to approximately 32 N m− 1 at 10− 4 M oleate concentration, and this value decreased to below 25 N m− 1 at the same surfactin concentration. According to contact angle measurement results, the contact angle of magnesite was 85° after the surfactin adsorption of 2 × 10− 4 M concentration, while this value remained at 46° for oleate. Finally, according to flotation experiments, high temperatures and high collector dosages are necessary for acceptable flotation recovery with oleate, yet surfactin can produce the desired result at ambient temperatures and lower collector amounts.

Dec 13, 2022

By Innocent John Arinze, Chidubem Okwudiri Emedo

This contribution presents the first multi-scale geophysical investigation conducted in the Abakaliki and Obubra mining districts (AOMD), southeastern Nigeria, for the exploration of shallowly emplaced (< 50 m) massive sulfide and barite mineral deposits. Raw airborne magnetic data covering the AOMD was acquired and subjected to diverse enhancement routines to facilitate the identification of areas of subtle magnetic anomalies for subsequent ground truthing. The mineralization is mainly made up of galena, sphalerite, and barite. The contrasting physical properties between these minerals and their host rocks make resistivity, induced polarization (IP), spontaneous potential (SP), and magnetic methods ideal to study and delineate the mineralization and possibly locate the ore bodies. Wenner DC resistivity and IP data acquired along the same parallel traverses are inverted using Res2dinv to produce 2D tomography models of resistivity and chargeability. The resistivity and IP models were successful in delineating zones of sulfide and barite mineralization. The ground SP data collected along the same traverses as the resistivity and IP data were interpreted as line graphs. The 1D SP models show a number of central negative anomalies that could be related to sulfide mineralization. These anomalies show fair-to-good spatial continuity and are in close agreement with the result obtained in the resistivity and chargeability model. This study suggests the presence of exploitable mineral deposits in the AOMD and demonstrates the superior interpretative ability of combined geophysical methods over a single geophysical approach.

Oct 20, 2020

By Weiran Zuo, Wanzhong Yin, Jin Yao, Keqiang Chen, Qiuyue Sheng, Liu Liu

It is important to investigate the liberation properties of gangue minerals and establish liberation models for low-grade iron ores to reject gangue early. In this study, three types of iron ores from different iron deposits were ground to different particle size distributions by locked-cycle grinding and batch grinding. The liberation distribution of quartz, the most dominant gangue mineral among the three types of iron ores, was tested by Mineral Liberation Analyzer (MLA). Afterward, the liberation distribution of the three types of quartz was fitted using the beta distribution function, and their shape parameters were related to particle sizes to develop the liberation model. MLA test results showed that the liberation distribution of quartz with different grinding methods was basically the same. The developed liberation model predicted the liberation distribution of quartz in low-grade iron ores from different iron deposits well, and its coefficient of determination (R2) was between 0.90 and 0.98. This study deepens the understanding of the liberation rules of quartz in low-grade iron ores from different iron deposits, and on this basis, a more efficient liberation model based on the beta distribution function is developed.

Oct 18, 2023

By Ben V. Petersen

Surveying is to tunneling, as a steering wheel is to a car—somewhat essential if you want to end up in the right place. The principles of tunnel surveying have remained unchanged since the first tunnels were constructed: To mathematically connect the selected start and end points of a tunnel and physically translate that alignment onto the ground. The alternative is just dead-reckoning and leaves the probably less than satisfying end results to chance. Today’s laser-guided tunnels often have to thread the needle through a maze of soil types, utilities, structural features and other underground considerations. Surveying makes it possible.

Jan 1, 2005