Search Documents

By J. D. Miller

The sedimentary western phosphate deposits of Idaho, Montana, Utah, and Wyoming tend to be calcareous and generally carry a significant amount of dolomite along with collophanite. In some cases, such as the Smokey Canyon Mine, Afton, Wyoming, the ore will also contain mudstone, and in this case the aluminosilicate minerals (clay, feldspar, etc.) together with some dolomite are floated from the collophanite in column flotation cells with an amine in order to meet product specifications (31 % P205) (Service et al.). In other cases, such as the SF Phosphates Limited Mine, Vernal, Utah, the ore is treated by traditional fatty acid flotation of the collophanite with mechanical flotation cells (Weber, 1986). Preliminary tests have now been conducted to evaluate air-sparged hydrocyclone (ASH) technology for the flotation of western phosphate ore. For this preliminary study, samples were taken from the hydrosizer overflow stream (18-21 % P205) at the SF Phosphates Limited Plant in Vernal, Utah for scavenger flotation testing with the 2-inch ASH system in laboratories at the University of Utah. Selected design and operating variables are being studied, and the initial results show that satisfactory separations can be achieved by high-capacity ASH flotation at appropriate operating conditions. For example, with single-stage ASH flotation 80% recovery can be obtained with a scavenger concentrate grade of about 26% P2O5. These results are comparable to, or better than, those obtained at SF plant operations with conventional flotation cells and suggest that ASH flotation technology can be used to good advantage in the phosphate industry. Of course, research should be continued to consider other process streams, optimize the separation efficiency, and evaluate larger diameter ASH units.

Jan 1, 1993

By E. A. Schmidt

In 1962, while investigating the tungsten potential in the Thompson Creek area for Union Carbide Corp., Henry T. Eyrich obtained anomalous concentrations of molybdenum (up to 19 ppm Mo) from stream sediment samples collected along Pat Hughes Creek, a tributary to Thompson Creek. Follow-up investigations by Eyrich during the same year disclosed the presence of a hydrothermally altered and molybdenite-bearing granitic exposure in the headwaters of Pat Hughes Creek about 2.4 km (1.5 miles) upstream from the sample point. The altered outcrop measured about 549 by 305 m (1800 by 1000 ft), contained abundant northwest-trending quartz veins locally with molybdenite, and was overlain and surrounded by the Challis volcanic extrusive sequence of mid-Tertiary age. Eyrich's subsequent soil and rock chip geochemical sampling program over the altered outcrop area showed a general increase in the molybdenum content to the northwest toward the postmineral Challis volcanic cover. Over a distance of about 305 m (1000 ft), values in the altered intrusive rock increased from less than 5 ppm Mo to over 600 ppm Mo, with aconcomitant intensity of the hydrothermal alteration pattern. Based on these geochemical results and on preliminar; megascopic hydrothermal alteration studies, Eyrich correctly concluded that the altered outcrop is an erosional window and that molybdenum mineralization of sufficient grade could exist beneath the Challis volcanic cover some distance further to the northwest. His recommendation to test the area of potential molybdenum mineralization with several drill holes was, however, declined by Union Carbide in 1962. The property remained unclaimed until 1967, when Eyrich joined Cyprus Mines Corp. Acting on Eyrich's recommendation, Cyprus immediately staked 26 lode mining claims to cover not only the altered intrusive outcrop, but also the northwest trend of mineralization where it projected beneath Challis volcanic rocks. Eleven of these claims are now patented.

Jan 1, 1991

By R. C. Richardson

Barite Worldwide barite production for 1985 decreased 1.3%, while US barite production increased 1.4%, according to US Bureau of Mines statistics. The increase in US production is attributed to heavy demand for oil and gas drilling during the first quarter and an unrealized heavy expected demand in oil and gas markets for the last quarter. Nevada accounted for 82.1% of the 807 kt (890,000 st) of barite produced in the US last year, according to the Bureau. Other producing states were California, Georgia, Illinois, Missouri, Montana, Tennessee, and Washington. In 1985, the US imported 1.8 Mt (2 million st) of crude barite and 64 kt (71,000 st) of ground barite. China led the way with 43.3% of the total. Imports from India accounted for 21.6%; Morocco, 15.5%; and Thailand, 5.6%. The 1.8 Mt (2 million st) of crude barite imported is an 18.8% increase over 1984. Apparent consumption of barite for 1985 was about 2.6 Mt (2.9 million st), a 15.7% increase from 1984. Due to very low drilling rig activity during the last quarter of 1985, actual consumption is probably less as crude barite inventories at mines and plants increased. According to the Bureau, 90% of barite consumed in 1985 was for the oil and gas market. Paints, rubber, glass, and other chemical uses consumed the other 10%. With the price of oil falling dramatically early in 1986, the outlook for oil and gas drilling looks to be significantly lower than 1985. This lower demand for barite, coupled with the high year-end inventories, should lower both imports and domestic production. Significant lower prices on imported barite are expected, especially from China, Morocco, and India. This also could further lower US production of barite this year.

Jan 5, 1986

By Xiaozhen Song, Ashish Ranjan Kumar, Shimin Liu

To investigate the influence of boreholes, fans, and curtains for large opening underground mines (LOUM), we conducted a field survey for LOUM with the survey data serving as the numerical modeling inputs using computational fluid dynamics (CFD) models. Five different CFD modeling results were obtained with different borehole, box fan, and curtain setting conditions. The results indicate that most air quantity directly escapes through outlet 1 after coming into the inlet, causing a huge loss of airflow; volumetric air exchange index (VAEI) and minimum hours of fully exchanging the air (MHFEA) measure air exchange efficiency, with zone 2 of case 5 having the highest VAEI; The borehole minimally affects zones 2, 3, and 4, but drastically alters airflow direction in zone 1; The box fan enhances airflow to zone 2, improving ventilation efficiency and increasing VAEI; Curtains have little effect on distant working faces but influence airflow near inlets and outlets. This study provides a foundation for future research on the influence of boreholes, fans, and curtains, as well as optimizing their placement and effectiveness in face ventilation.

Feb 22, 2026

By C. Webb, M. A. Tuck

This paper describes the application of a cable disc elevator to continuous lift ore vertically from underground mines. Application of this system requires the tensions developed within the cable must remain within the carrying capacity of the cable including applicable safety margins. A critical element occurs at starting the system when it is fully loaded which requires the force developed by the system to exceed the static friction forces. This paper describes the laboratory rig developed to investigate the static friction forces. Details of the results of tests on three different ores for both dry and wet conditions are given. These results are discussed.

Nov 19, 2020

By Y. J. Zhang

This paper presents the results of a recent study on the development of an in-situ testing method for determining the coal strength in mine pillars. The strength testing is performed in the horizontal holes drilled into the coal rib using the penetrometer. It is a hydraulically powered device that uses an indenter to press the surface of the borehole until the load reaches the failure point of coal. The pressure and the penetration of the loading pin are recorded by the data acquisition unit. The results collected from several coal mines indicate that this testing method is ideally suited for the realistic coal strength measurements. The new testing system not only improves the accuracy of pillar strength determination, but it is more cost efficient than the conventional method.

Jan 1, 1995

By Osvaldo A. Bascur

Standards and technology for bringing information to the desktop have greatly evolved in recent years. The benefits to be realized depend on how these new tools are embraced at the performer level. A key operating challenge is to ensure cooperative effort is geared towards the most efficient achievement of identified operating and corporate objectives. Presentation, application and database layers are emerging in successful client/server applications, the three-tier architecture.

Jan 1, 1996

By Serdar Aktaş, Burcu Nilgün Çetiner

According to critical statistical studies, antimony is one of the rarest elements in the world, and global resources could be exhausted by 2050. In light of these observations, its extraction will be costly due to poor-quality ore, deep mining, remote locations, and high energy consumption. In the present study, an alkaline leaching process was carried out on stibnite concentrate to evaluate the effect of reaction parameters on the percentage of antimony extraction. The leaching efficiencies of different sulfur and hydroxide sources were studied and compared to one another to create a better understanding of the reaction process. Kinetic models were investigated to identify the reaction pathway and calculate the activation energy. The activation energy of the stibnite dissolution was assessed as 19.13 kJ/mol using a two-dimensional diffusion-reaction model. The value of activation energy indicates the quantity of energy necessary for a reaction to proceed. As expected, potassium hydroxide leaching was significantly more successful than was sodium hydroxide; however, in terms of economics, the use of sodium hydroxide was found to be more cost-efficient. Interestingly, this finding indicated that caustic leaching is still the most effective method for stibnite extraction.

Jul 23, 2020

By V. G. Lofftus

Since plant start-up in January 1983, Golden Sunlight Mines, Inc. has implemented several process changes and improvements. Among these are a pulp preaeration circuit and a sand tailings retreatment circuit. The purpose of the preaeration circuit is to reduce reagent consumption during gold dissolution. The sand tailings retreatment circuit was added to recover and process separately pyrite concentrate to maintain acceptable overall gold recoveries with the more refractory sulfide ores. Research and plant operating data along with process and improvement descriptions are presented.

Jan 1, 1987

By CHONG WEI, TATYANA KATSAGA, DEREK APEL

This study provides an effective determination process of the interface microstructural parameters in the numerical modelling of the mechanical interaction between two different geomaterials involved with frictional-bonded interfaces, such as the interaction between backfill columns and the surrounding rocks, or the soil-structure interaction, by using the coupled finite-difference and discrete-element (FD-DE) method. Three-dimensional numerical direct shear tests were conducted on the coupled FD-DE model of the combined rock-cemented rockfill (R-CRF) specimens with the frictional-bonded interface. With the microstructural parameters determined, the macro-mechanical properties of the interface of the coupled model were calibrated to well fit with the theoretical values of the combined specimen under the direct shear condition assumed according to the Mohr–Coulomb strength criterion. Evident elastoplastic shear behaviour was observed on the interfaces, and excellent agreement was attained between the shapes of the theoretical and simulated shear stress-displacement curves of the coupled models at different servo-controlled normal stresses. Particulate-scale force chains inside the DE model of the CRF specimen were highly consistent with the force contour on the FD model of the rock specimen, demonstrating the shear stress evolution of the coupled model at different shear displacements. Parametric studies verified the effects of the deformation properties of the interface parallel bonds on the shape of shear stress-displacement curves of the coupled models. The test results validated the feasibility and rationality of the coupled FD-DE method for modelling the combined specimens with frictional-bonded interfaces or joints. Furthermore, this study provides valuable numerical modelling experience for investigating the shear behaviour at the interface between cemented backfill columns and surrounding walls by using the coupled FD-DE method.

Nov 2, 2021

By Bruce E. Kester

The concurrent observation of the phenomena of alkali-aggregate reaction and development of efficient dust collection systems on rotary kilns made mandatory the process modifications to produce low alkali cements. Such low alkali cements as were available prior to these recent changes were either the rare result of low alkali raw materials, the loss of alkalies with dust loss from the kiln stack, or in some instances by the use of CaC12 in the kiln feed to increase volitalization of the alkalies and their subsequent loss or discard with the normal dust emission from the kiln. The relative slowly soluble nature of natural occurring alkali minerals in cement raw materials as compared to the very soluble nature of the alkali salts as present in cement kiln reaction products, either in clinker or in dust emission led to the development of the water leaching system. Two distinctly different problems of leaching are created by the two major systems of portland cement production, the wet and dry processes. The wet process is characterized by moderate dust loads and concentration of soluble forms of alkali in the dust. Further the return of the leached dust slurry does not materially change the characteristics of kiln feed on reintroduction and subsequently does not materially influence kiln operation. The dry process differs in high levels of dust emission and the presence in the collected dust of large amounts of unreacted kiln feed with its sparingly soluble alkali minerals. In the dry process reintroduction of leached dust slurry changes the dry process to what may be classed as a damp process. This change results in some decrease in kiln capacity and creates conditions of operation which are uncommon to either the wet or dry process.

Jan 1, 1963

By Kevin Vander Tuig, Tim O’Rourke, Rick Vincent, Doug Lopata, Kellie Rotunno, Dan Dobbels

"The Northeast Ohio Regional Sewer District (NEORSD) was required under the Federal Clean Water Act and U.S. Environmental Protection Agency’s (U.S. EPA) Combined Sewer Overflow (CSO) Control Policy to develop a Long Term Control Plan (LTCP) to reduce or eliminate overflows from its permitted CSO outfalls. The LTCP was completed in 2002. Key components of the plan include: 26 miles (42 km) of deep storage and conveyance tunnels providing a total CSO storage volume of 325 million gallons (MG) (1.2 billion liters); over 30 miles (48 km) of consolidation sewers to route CSO control flows to the tunnels; and associated diversion/inflow control structures and drop shafts. Final design and construction of the initial phases of the LTCP are completed or underway. Advanced planning of the final phases began in April 2013. This paper summarizes this advanced planning process and, specifically, how hydraulic performance and tunnel design and construction considerations were balanced to eliminate unnecessary projects and shafts, reduce implementation risks, and reduce program costs by approximately $650 million. BACKGROUND The Northeast Ohio Regional Sewer District (District) serves an area of approximately 350 square miles (SM) (907 km2), including combined (81 SM; [210 km2]) and separate (269 SM [697 km2]) sewer systems that discharge to three wastewater treatment plants in the greater Cleveland area. The service area, shown in Figure 1, is divided into three districts—Easterly, Westerly, and Southerly—each having its own interceptor system and treatment plant, ranging in wet weather treatment capacities from 100 to 735 million gallons per day (MGD) (378.5 million to 2.8 billion L/day). The system includes 124 permitted combined sewer overflow (CSO) outfalls overflowing into the region’s tributary streams, Cuyahoga River, and Lake Erie."

Jan 1, 2016

By P. M. Soupios

An integrated suite of environmental methods was used to characterize the hydrogeological, geological and tectonic regimes of the study area, to determine the geometry of the landfill (depth and spatial extent of electrically conductive anomalies), to define the anisotropy caused by bedrock fabric fractures and to locate potential zones of electrically conductive contamination. The study area which covers an area of about 0.08 Km2 is a municipal solid waste site (MSW), located 20Km West of Herakleion in the central part of Crete (S. Greece). The landfill is located in a northwest oriented valley with highlands to the northeast and southwest. The combination of geophysical methods and chemical analysis are commonly implemented for characterization and management of land-fills. At the particular site, geophysical methods were focused on studying the electrical insolating properties of the materials, electrical con-ducting properties of fluids (leachates) and electromagnetic properties of the disturbed regolith materials in the burial zones. Three different types of geophysical surveys were performed: 1) 2D electrical tomography (ERT), 2) electro-magnetic measurements using very low frequencies (VLF) and 3) electromagnetic conductivity (EM31). Furthermore, in order to calibrate the geophysical methods dielectric spectrometry measurements are conducted. To evaluate the environmental degradation of the area, soil and liquids samples were collected.

Jan 1, 2005

Jan 1, 1998

By J. H. Kempton

Refinement of environmental procedures can produce significant cost savings at most mines. Grouting permeable aquifers reduces water pumping and disposal costs. Stable groundwater quality supports reduced groundwater monitoring; and for contaminated groundwater, in-situ or natural restoration should be evaluated. Waste-rock characterization can be minimized using fewer (but more representative) samples, inexpensive surrogate analyses (e.g., NAG instead of humidity cells), and appropriate tests (e.g., avoid meteoric tests on sulfide). Selective waste-rock handling should be compared to random emplacement, which is often cheaper and more stable. Finally, incorporating schedule uncertainty in modeling allows the flexibility to revise mine plans within permits.

Jan 1, 2000

By Syd S. Peng

Is the laboratory sized coal specimen much stronger than underground coal pillars? The answer to this question has a profound implication to many coal operators. It will decide how much of the coal reserve can be recovered. Or, in many cases, it will determine whether it can be mined economically. Recent trends in several eastern states to establish regulations regarding coal pillar design to prevent surface subsidence long after mining heighten the debates. And, in some cases, these trends highlight the existing practices that seriously question the conventional wisdom. Currently, nearly all researchers and practitioners agree that as the size of rock specimens increases, its strength decreases. This concept has been universally adopted as the basic principle for coal pillar design in the United States. Several formulas have been derived to account for this effect. The reduction factor for underground coal pillars ranges from one-half to one-sixth of the strength obtained in the laboratory, depending on the formula selected. Recent case studies indicate that the reduction factor is not justifiable, at east in some cases. The use of a reduction factor is based on the assumption hat smaller rock specimens as tested in he laboratory contain none or fewer fractures or planes of weakness than larger specimens or underground coal pillars. In other words, the larger the rock materials, the more fractures it contains and subsequently weaker in strength. Do all underground coal pillars have more fractures than laboratory sized coal specimens? Not necessarily. All coal contains cleats. Some are con¬spicuous but others are not. In terms of cleat density (number of cleats per unit area), there is no difference between an underground coal pillar and a laboratory sized specimen, provided the specimen size is larger than the cleat spacing, which is mostly 25 to 75 mm (1 to 3 in.).

Jan 1, 1993

By John S. Wakeman

The initial step in the pelletizing of iron ores is the production of green balls. The importance of this step cannot be overemphasized as the physical quality of the green balls has a very significant effect on the subsequent induration process, regardless of the type of the indurating equipment employed. The ability of the green balls to withstand the rigors of handling, distribution, compaction and drying will have an effect on the degree of success of any pelletizing operation. Many factors affect the physical quality of the green balls including the prior processing of the iron ore, the characteristics of the balling feed and the type and quality of the binder used (if any). When working on the development of a new project or studying an existing operation, it is often desirable to determine what effect variations in these factors will have on green ball quality. It is generally impractical to make these determinations on a commercial, or even pilot plant scale, especially when the number of variables to be studied is large. Because of this, many organizations have developed batch techniques for producing green balls to enable them to perform such investigations with a minimum of time and expense. The batch balling method is at best, only an approximation of commercial balling systems. Many practitioners employ the use of pre-formed seed pellets to initiate a batch run. Thus, the growth mechanism encountered in any experiment is essentially snowballing. Unless an instability is introduced into a balling test (such as an excessive initial feed rate or an unusual feed material characteristic) the growth mechanism of coalescence is not present to a significant extent nor is it desirable. In a continuous operation, both mechanisms are present and necessary to sustaining the system. The batch balling technique thus produces pellets in an idealized manner and cannot be used to directly predict commercial green ball qualities. A general relationship does exist however, and the procedure is fairly sensitive to variations in test parameters. Although many refinements to this technique have been introduced over the years, batch balling is still essentially an art and subject to "operator effect". Therefore, to assure consistant and reliable results, skilled technicians who carefully adhere to established practice must be utilized.

Jan 1, 1971

By S. K. Sharma, ANKUSH GALAV, G. S. P. Singh

Providing a suitable protective water barrier pillar (PWBP) is common to reduce inundation hazards in underground coal mines. The imperative factors influencing its performance include the water head acting on the pillar, cover depth, pillar width, strength properties, and permeability characteristics. The mechanical failure of such pillar is a stress-controlled phenomenon, whereas the hydraulic failure is a strain-based phenomenon. A finite-difference numerical modeling approach was developed to study the hydro-mechanical coupled behavior of protective water barrier pillars. The mechanical stability was evaluated in terms of the percentage of failed (ZoF) and intact zones. The influence of the strain-controlled weakening on the permeability of the flow medium was studied through the coupling of the mechanical and hydraulic effects. The coupled steady-state model was used to estimate the outflow rate and its hydraulic stability. The adequacy of the protective pillar was also investigated by assessing mechanical stability and capability to resist hydraulic pressure against the maximum expected water head. A seepage rate-based classification system has also been proposed to evaluate the seepage potential and assess the hydraulic stability. The model has been validated for two case studies at the cover depth of 136–189.5 m and the existing pillar width of 16–42 m against the water head of 25–141 m.

Aug 18, 2022

By P. E. Sperry, R. E. Heuer

The United States Bureau of Reclamation is constructing the $200 million Navajo Indian Irrigation Project to irrigate 110,000 acres of land on the Navajo Indian Reservation in northwestern New Mexico. Water from the San Juan River is impounded by Navajo Dam and will be conducted for 26 miles along a series of tunnels and canals to the area to be irrigated. Tunnel No. 3 is the third in a series of six tunnels along the route. Bids for construction of Tunnel No. 3 were received by the Bureau of Reclamation in September, 1970. Fluor Utah was low bidder at $8.7 million. Ten of the 12 bids were based on excavation by tunnel boring machine. The consulting firm of A. A. Mathews, Inc., was retained by the contractor to advise on geologic and rock mechanics conditions after support problems developed in the tunnel. Tunnel No. 3 is 15,264 feet long, has an 18 foot lined diameter, rises approximately one-half inch per 100 feet in the direction being excavated, and is 6,000 feet above sea level. There is one short curve in the alignment. Minimum concrete thickness is 12 inches with eight inches from 'A' to 'B' line making a pay diameter of 21 feet, 4 inches. The tunnel is supported with rock bolts and steel pans. Mole excavation began on May 13, 1971 from a blasted starting chamber. After 46 feet were excavated the mole was shut down and the trailing muck handling equipment was pulled into place. After advancing 1,700 feet in 34 days, unanticipated ground water conditions and ground support problems were encountered slowing moling so that the next 1,000 feet of advance consumed 97 days until December

Jan 1, 1997

By E. O. Mixon, Jack D. Kennedy

INTRODUCTION This contract is the most northerly portion of the Metropolitan Sanitary District of Greater Chicago's Tunnel and Reservoir Plan. (TARP) The project begins at Addison Street in Chicago and proceeds northerly approximately ten miles to end at Wilmette Harbor and Lake Michigan. The project which consists of 2 work shafts, 32 drop shafts, 7.322 km (24,020 ft.) of 6.7 m (22 ft.) diameter circular rock tunnel, 8.458 km (27,750 ft.) of 9.2 m (30 ft.) diameter circular rock tunnel and miscellaneous rock bolting and grouting, was bid for a total cost of $63,140,480. The tunnel invert elevation varies from 65.5 m (215 ft.) to 77.4 m (254 ft.) below the ground surface, which places the tunnel in a rock formation of dolomite limestone. At the tunnel invert, the unconfined compressive strength of the limestone varies from 96 MPa (14,000 psi) to 152 MPa (22,000 psi). The 6.7 (22 ft.) diameter tunnel required the mining of 10.9 cu m. (14.2 cu yd.) of rock per lineal foot of tunnel while the 9.2 m (30 ft.) diameter tunnel required the mining of 20.1 cu m (26.3 cu yd.) of rock per lineal foot of tunnel. The total cubic meters of rock required to be excavated from both tunnels was 818,821 cu m (1,070,978 cu yd.). All of this will be mined by tunnel boring machines (TBM). These tunnels were not to be lined with concrete. The thirty two drop shafts have upper portions that are cylindrical in the overburden and rock sections. They were divided into two groups, depending on diameter, with a different construction method for each group. The first group consisted of twenty three of the

Jan 1, 1979