Search Documents

By Andrew R. Thomas

As the demand for most industrial minerals on the world market continues to climb, educational institutions maintain traditional policy in emphasizing chiefly metallic ore deposits and energy resources in addition to the general disciplines. In spite of their increasing importance, few universities exhibit great depth with respect to industrial minerals courses due to the shortage of specialized faculty in a category this broad. As new ideas are formulated and technological advances are developed in the field of industrial minerals, the classroom still exists as a student's primary source of information. This opportunity to give today's students the benefit of modern developements has not been utilized to its utmost potential.

Jan 1, 1981

By S. Potgieter-Vermaak, T. T. Chiweshe, W. Purcell

Complete isolation of chromium (III) from the reference material (SARM 131), Upper Group 2 (UG2) chromite ore, and Merensky Reef mineral ore was achieved using ammonium phosphate salt as flux. Optimum pH (3.2–3.8) conditions and sample to flux ratios (1:25) were some of the factors that were critical for the complete isolation of chromium. Increasing the sample to flux ratio (1:50 excess) however resulted in the conversion of all the elements in the melt into a green solution (pH, 5.8–6.7). A different chromium compound was subsequently isolated from the green solution by allowing this solution to stand in an open vessel in a cupboard for a month during which time the pH decreased to pH 3.5–4.2. Quantitative analyses of chromium from the isolated precipitates of SARM 131, UG2 chromite ore, and Merensky Reef mineral ore indicated chromium contents of 41.87, 60.41, and 23.93% respectively which were very close to the chromium content in the original samples. Analysis of the chromium precipitates using IR indicated the presence of phosphates (1100–1200 cm−1 ) while SEM-EDX analysis showed the presence of microscopic crystalline particles with Cr, P, and O as the major elements. Further characterization of the chromium precipitates using XRD and Raman successfully identified the product as chromium (III) metaphosphate C-type (Cr(PO3)3, JCPDS no. 01-077-0672), in the isolated chromium precipitates.

By Yun-tao Xin, Yu Yi, Kang Yan, Gang Li, Xiao-dong Lv

This study investigated the selective removal of arsenic from high-arsenic dust in alkaline systems and the effects of different leaching conditions. The results indicated that the liquid–solid ratio, NaOH concentration, and sulfur dosage had a significant influence on the process. The leaching efficiency of arsenic reached 99.57%, while that of lead was as low as 0.03% under appropriate conditions. In particular, the addition of sulfur can effectively promote the leaching of arsenic and reduce the dissolution of lead in the solutions. An artificial neural network was used to model the leaching process. It consisted of a back-propagation artificial neural network model with a “6–10–2” structure that could effectively simulate and predict the value with more than 99% accuracy. Based on the difference in weights of the different parameters in the neural network model, the relative importance of the parameters related to arsenic and lead leaching efficiency was obtained, which followed the order of NaOH concentration, liquid–solid ratio, sulfur dosage, temperature, time, and stirring speed.

Jul 29, 2021

By D. Men, R. Q. Honaker, J. C. Hower

"Maceral separation is one possible technique to expand coking coal resources, either by increasing the blending ratio of non- or slightly caking coal or rationally utilizing the coking coal according to the different behaviors of macerals in coking. The success of maceral enrichment for a given coal using flotation is dependent on the differences in flotation kinetic rate among macerals. This paper presents the flotation rates and zeta potentials of the vitrinite-rich and inertiniterich maceral concentrates obtained from six coal samples of different ranks – from high-volatile B bituminous coal with mean random vitrinite reflectance (Rrandom) of 0.64 percent to low-volatile bituminous coal with Rrandom of 1.73 percent – using a float-sink procedure. The flotation results show that vitrinite-rich concentrates can be produced in tap water using froth flotation only with frother for the high-volatile B and A bituminous coal samples, but there was no good performance for the high-volatile C bituminous and medium- to low-volatile bituminous coal samples. The zeta potential results show that froth flotation could probably separate the high-volatile C bituminous coal samples well by adjusting pH, but there was no good performance for the higher-rank coal samples. IntroductionMetallurgical coke is used in blast furnaces for steel production and is produced by the carbonization of coking coal. Because caking coals are rare and expensive, they are often blended with non- or slightly caking coals. Considering the tight supply-demand situation for coking coal in China, it is important and urgent to develop highly efficient technologies for rationally utilizing and expanding coking coal resources (Mochizuki et al., 2013)."

Jan 1, 2015

By Charles T. Ford

In 1971, Bituminous Coal Research, Inc~ established a program to provide the coal industry with the necessary information and technical capability to investigate and evaluate potential problems concerning trace elements in coal and coal-related materials. The initial efforts at BCR in developing or adapting analytical procedures for the precise determination of trace elements in the parts per million to parts per billion range were detailed in a report titled "The Development of Analytical Methods for Determining Trace Elements in Coal and Coal-related Products." A subsequent reports contained descriptions of reliable analytical methods refined by BCR for determining mercury in coal and coal ash and also in coal mine water. his paper reports initial progress in applying recently-acquired trace-element analytical capabilities to solving potential coal industry problems. In this case, the effect of a coal-cleaning process on the distribution and removal of potentially harmful trace elements in coal was evaluated. Coal cleaning offers the possibility of controlling potentially harmful emissions resulting from combustion of large tonnages of coal by removing the pollutants prior to combustion.

Jan 1, 1977

By Kent Phillips, Meredith Scaggs-Witte, Emily Sarver, Cigden Keles

"After nearly four decades of decline, the prevalence of coal workers’ pneumoconiosis (CWP, or black lung) in the United States has been on the rise since the mid-1990s (Laney et al., 2014; Laney et al., 2010; Suarthana et al., 2011; Pollock et al., 2010; Antao et al., 2005; Blackley et al., 2016). Particularly alarming is the number of cases of rapidly progressive disease such as progressive massive fibrosis (PMF) (Pollock et al., 2010; Antao et al., 2005; Blackley et al., 2016; Laney et al., 2017). A recent study by Laney et al. (2017) observed 192 U.S. coal miners participating in the Coal Workers’ Health Surveillance Program (CWHSP) who had been diagnosed with PMF since 2000. Of the 163 (85 percent) that had a normal radiograph on file to use as a baseline, 27 (17 percent) of these individuals had progressed from a normal radiograph to PMF diagnosis in less than 10 years. Moreover, 162 (84 percent) of the individuals in that study worked in Kentucky, West Virginia or Virginia, and 169 (88 percent) had only ever mined underground. Blackley et al. (2016) also reported on a group of 60 PMF cases that were discovered by a single black lung clinic in eastern Kentucky. Since seeking care at such clinics and participation in the CWHSP are voluntary, and could be influenced by a number of factors, there has been some concern that these reports may overestimate the degree of resurgence in severe disease (i.e., versus disease that was previously under-reported). Even so, they highlight a critical need to better understand the cause(s) of disease development and progression — such that effective interventions can be devised.The notable uptick in CWP and PMF rates among miners in central Appalachia has led to this region being called a hot spot for disease (Pollock et al., 2010; Antao et al., 2005; Blackley et al., 2014; Laney et al., 2017). While the geographic clustering has been well documented (Pollock et al., 2010; Antao et al., 2005; Wade et al., 2011; Wang et al., 2013), the root cause is still unknown. Leading hypotheses have focused on the relative amount of rock being cut along with coal in many central Appalachian mines, as there has been a tendency to mine increasingly thinner coal seams over the past couple of decades (Laney et al., 2010; Schatzel, 2009). This shift has likely been accompanied by changes in specific dust exposure factors, such as increased abundance of particularly harmful dust constituents (e.g., silica or silicates) or increased frequency of harmful exposures (e.g., due to work in more risky environments) (Pollock et al., 2010; Blackley et al., 2016; Cohen et al., 2016; Douglas et al., 1986)."

Jan 5, 2018

By Montaser S. El‑Salmawy, AHMED A. S. SEIFELNASSR, Ahmed Al‑Abady, Abdeaziem M. Abdelaal, Amr F. M. Ibrahim

Iron is a key detrimental impurity in silica sands that determines their contribution to high-technology industries. Herein, a simple ecologically sound approach is investigated for iron removal from a silica sand sample obtained from the El-Zaafarana area-Egypt. The sample was subjected to a detailed microscopic mineralogical study supported by XRD and XRF characterization. The sample was beneficiated using distilled water attrition scrubbing and screening over a 25 μm sieve followed by leaching using a mixture of equal amounts of phosphoric and oxalic acids. Leaching experiments were designed and analyzed using the Box-Behnken design (BBD) methodology. A model was developed and evaluated using the analysis of variance technique to map the relationship between the residual iron oxide in the produced concentrate and selected variables such as leaching temperature, oxalic acid, and phosphoric acid concentrations. XRD and mineralogical analysis reveal that quartz is the most dominant constituent of the studied sand and other minerals such as kaolinite, iron oxide, rutile, and zircon exist in trace amounts. The head sample shows a silica and iron oxide content of 95.69% and 2379 ppm, respectively. Attrition and separation over a 25 μm sieve increase the silica content to 97.05% and decreases the residual iron oxide to 455 ppm. The final product after leaching under optimized conditions shows 99.82% silica and 55 ppm iron oxide.

Aug 30, 2022

By Morgan M. Sears, Gamal Rashed, Michael M. Murphy, Brent Slaker

In this study, a parametric study was conducted using FLAC3D numerical models to examine the impact of oblique loading, generated from seam dip, on the strength and the failure propagation pattern of a stone pillar using two simplified geometry types. In type 1, the sidewalls of the pillars were assumed to be perpendicular to the roof and the floor, while in type 2, the sidewalls of pillars were assumed to be vertical. The complex pillar geometry in dipping mines was frequently modeled using these two geometries. To capture a complete picture of the effect of seam dip on pillar stability, the modeled width-to-height (W/H) ratio of the pillars, in situ stress field, and pillars roof/floor interfaces were systematically varied to account for the potential distribution of values for these parameters across the underground stone mines in USA. Results from the numerical modeling indicate that dipping pillars have reduced strength compared with horizontal pillars. Also, an asymmetric failure propagation pattern could be obtained depending on an interaction between the W/H ratio, seam dip, in situ stresses, and pillar geometry.

Feb 5, 2021

By N. Damiano, C. Zhou, B. Whisner, M. Reyes

"The industrial Internet of Things (IIoT)—a concept that combines sensor networks and control systems—has been employed in several industries to improve productivity and safety. NIOSH researchers are investigating IIoT applications to identify challenges of and potential solutions for transferability of IIoT from other industries to the mining industry. Specifically, NIOSH has reviewed existing sensors and communications network systems used in U.S. underground coal mines to determine whether they are capable of supporting IIoT systems. The results show that about 40% of the installed post-accident communication systems as of 2014 require minimal or no modification to support IIoT applications. NIOSH researchers also developed an IIoT monitoring and control prototype system based on low-cost microcontroller Wi-Fi boards, to detect a door opening on a refuge alternative, activate fans located inside the Pittsburgh Experimental Mine, and actuate an alarm beacon on the surface. The results of this feasibility study can be used to explore IIoT applications in underground coal mines based on existing communications and tracking infrastructure. INTRODUCTION The nation’s approach to health and safety in mining has historically been reactive in the sense that health and safety regulations and mandates have traditionally been passed as a result of tragic mining accidents. An example of this is the Mine Improvement and New Emergency Response Act (MINER Act) of 2006, which was passed as a result of several mining accidents where tracking of and communications with underground personnel were severely limited. While this reactive approach has led to the development and implementation of highly impactful safety interventions and safety practices, there currently exists a technological revolution that can shift the paradigm toward a proactive approach based on preventative methods: Internet of Things (IoT). IoT is the network of physical objects or ""things"" embedded with electronics, software, sensors, and connectivity to enable that network to achieve greater value and service by exchanging data with the manufacturer, operator, and/or other connected devices [1, 2]. It should be noted that IoT has been defined from various perspectives, and hence numerous definitions exist in the literature. The apparent ambiguity of the IoT definition might be due to the fact that IoT is syntactically composed of two terms: internet and things. The first one pushes towards a network-oriented vision, while the second tends to put the focus on generic objects. The traditional internet can be viewed as an internet of computers —i.e., “things” connected to the internet are computers only. IoT “extends” the internet by allowing other generic things that are commonly found in our daily life, such as refrigerators and cars, to be interconnected via the internet, and thus creates a bridge between the virtual word and the physical world."

Jan 1, 2017

By J. Kern, M. Cain, T. Torries

Until recently, the generation of electricity was regulated in all states and the value of generation assets in a regulatory environment for ad valorem taxation were based largely on the book value of the plant plus the rate of return on capital allowed by the state regulatory agency. This method of appraising utility generation assets is inappropriate in a competitive environment because past capital expenditures are not relevant in a competitive environment. However, it is not clear what valuation methods are appropriate after restructuring. This paper identifies key problems and advantages of other appraisal methodologies and makes comments on various valuation and taxation methods.

Jan 1, 2001

By R. L. Derick

On a regular basis, mine personnel should obtain air samples directly from active underground areas as well as remotely from sealed locations. These samples provide mine officials with data relative to the makeup of the various atmospheres. Should conditions underground change, these results can provide a baseline that can assist officials in determining the extent of change. Relating the concentrations of individual gases to time, applying gases to equations, and examining their change over time are tools that have been successfully used to determine if a heating event exists and, if so, the extent of the emergency. These atmospheric status equations have either been developed for the mining industry or adapted from other industries. They serve as tools to assist personnel in determining the condition of underground mine atmospheres. As long as the problem area continues to be ventilated, certain gases, gas ratios, and equations can be used to determine if a fire exists, what type of material could be burning, and what quantity of coal is burning. Once the mine or the involved section has been temporarily sealed, gases, ratios, and gas-derived equations can assist personnel in determining how conditions within the sealed volume are changing over time. To alleviate potential explosions when fresh air is once again introduced into the sealed volume, equations and a diagram have been developed to predict the likelihood of an explosive atmosphere. Similarly, prior to commencing recovery of a mine or section, equations exist that can assist in determining if the fire will rekindle when air is reintroduced. This paper serves as an overview to remind and/or instruct readers about gas-sampling methodologies and gas analyses to assist in determining the status of underground atmospheres.

Jan 1, 2006

By M. V. T. Da Silva, J. C. Harrison

Eldorado Gold Corporation of Vancouver, B.C. owns and operates three gold mines. The São Bento underground gold mine in Minas Gerais State, Brazil produced 105,907 ounces in1997. The La Colorada and La Trinidad open pit, heap leach mines in Mexico produced over 83,000ounces in 1997. With a deteriorating gold market plaguing the industry throughout 1997 Eldorado had to take critical measures at each mine to enhance gold production while lowering cash operating costs. Each mine had its own unique problems to confront. This case study will discuss three distinct courses of action taken at the three mine sites.

Jan 1, 1999

By NILAMADHABA SAHU, Gajanan U. Kapure, Pankaj Kumar, Sunil Kumar Tripathy

Chromite ore processing tailings and low-grade manganese ores are typically considered waste due to their limited or negligible utility, leading to environmental and storage concerns. Researchers globally have explored various methods to utilize or upgrade these wastes, particularly because dumping chromite ore has been linked to severe health issues through Cr(VI) leaching. Individually, these ores lack economic value, and there has not been research on simultaneously reducing both low-grade ores. In this study, the focus lies on smelting these ores together, aiming to create a precursor alloy for 200 series stainless steel scrap. Initial research indicated the potential for scrap formation, validated through lab experiments with varying coke rate, basicity, and holding time. The investigation discovered that smelting this combination could yield a metal product comprising 59% Fe, 24.93% Cr, 7.56% Mn, 0.62% Ni, and 0.93% Si. The optimum basicity was found to be 0.6 with 80% recovery. Notably, this process eliminates intermediate steps in 200 series stainless steel production, potentially reducing overall CO2 emissions. This proposed method represents a cleaner, sustainable approach to repurpose these two waste ores, projecting a net profit of USD 330 per ton.

Jan 10, 2024

By Jack T. Work

Spiraling costs in every segment of the open-pit mining cycle is a fact of life that every operator must reckon with. The introduction of various shock absorbing devices for rotary drilling is one recent innovation that may significantly reduce overall drilling cost, increase drill availability, and lower maintenance requirements. In a recent all-inclusive test in taconite ores, shock absorbers on Bucyrus-Erie BE 60R and Gardner¬Denver GD 120 rotary drills were directly responsible for overall savings of up to $41.06 per hour. What is It? A shock absorber is simply a device installed between the rotary drive head and drill steel that cushions the two. It functions in the same manner as springs and shocks on an automobile. Some benefits associated with use of the tool are readily apparent on a daily basis; other benefits are realized over longer time intervals and through continued use. A properly designed shock absorber will: •protect the drill from severe vi¬brations, improve rock bit performance, allow application of the best weight-on-bit and rotating speed under all drilling conditions, •function effectively over a wide range of applied bit weights, • have a spring rate soft enough to perform its primary function of absorbing both rotary and vertical vibrational forces generated by rough drilling, •be reliable and subject to as little maintenance as possible, •be easy to install and remove, and • be of such an economic benefit so as to offset the added expense of its application. A shock absorbing tool developed by BJ-Hughes Inc. was used in a recent test. The "Smoothdrill" is just one of the products currently available. This unit absorbs both rotary and vertical shock loads and has no mechanical parts so lubrication is unnecessary. A rebuild of the unit consists of removing the worn rubber element and inserting a new element, an operation taking less than one hour. Minimizing Vibrations Severe vibrations on a blasthole drill operating in broken and discontinuous formations have visible effects. These vibrations often cause structural damage when allowed to' continue, resulting in fatigue cracks in the mast and related structural components in the drill. When rough running formations are encountered, drilling must be interrupted and possibly shut down. Usually, the drill operator resumes drilling using less down pressures and various rotational speeds until firmer drilling is encountered. An effective shock absorber can substantially reduce these vibrational forces so more down pressure can be applied in bad ground. It is generally accepted that longitudinal vibrations and cyclic forces are more effectively reduced if a tool is designed to incorporate a relatively "soft" shock absorber. The softness of any shock absorbing tool is best judged by its spring rate-the weight required to produce a given amount of deflection, commonly expressed in units of kg per mm or pounds per inch of deflection. All shock tools use a resilient member such as rubber springs, steel springs, fluid, or gas springs to absorb

Jan 4, 1980

By Tracey A. Conrad, Mark E. Mussett, Max Kaufmann

The varied benthic habitats of the Pacific Ocean are comprised of different types of seafloor geology. These geologic domains generally consist of sedimented abyssal hills, high relief features such as seamounts, and polymetallic nodule fields that vary in spatial extent and abundance. Nodules represent a deep ocean habitat type, and are of economic interest owing to their metals content. Multibeam data can be used to classify seafloor geology. The wide swath of hullmounted multibeam systems used in deep water provides efficient coverage of large areas of seafloor. Our research examines how multibeam backscatter and bathymetry data, with regional environmental parameter assessments and GIS analysis, can help identify probable polymetallic nodule fields in the deep remote ocean prior to groundtruth seafloor observations. A workflow for processing 30 kHz hull-mounted multibeam data within QPS Qimera and FMGT software was developed to facilitate multibeam processing, while also generating a terrain model and backscatter products. An additional GIS protocol for evaluating multibeam data products, including cluster analysis, was also developed. These methods were applied to a test case of publicly available multibeam data collected by the Ocean Exploration Trust and NOAA. Processed multibeam products were used to identify areas exhibiting coarse sediment backscatter characterization with low relief; filters for water depth at or below the regional CCD, seafloor age, and sedimentation rate were then applied. Sophisticated GIS cluster analysis further identified trends within the data to forecast where coarse sediment domains, potentially including nodule occurrences, exist. The test case multibeam data allow determination of the composition and variability of seafloor geology. This analysis can further identify where previously unexplored nodule fields may exist and edify estimates of nodule extent throughout the ocean. The research methods and outcomes contribute to marine spatial planning, ecosystems modelling, and mineral resource management initiatives.

Feb 22, 2026

By J. W. Hawkins, K. B. C. Brady, K. Miller, J. Cuddeback

Remining of abandoned coal mines in Pennsylvania requires the implementation of pollution abatement and mining techniques called Best Management Practices (BMPs). Water-quality data from over 100 remining sites with more than 230 abandoned discharges were analyzed with respect to the types of BMPs employed to abate the pollution loadings of acidity, iron, manganese, aluminum and sulfate. Discharges exhibiting a significant decrease in acidity were most highly associated with sites where large volumes of alkaline materials were encountered (66.7%) or added (63.7%). The best results for iron loading were achieved with large-quantity alkaline addition (54.6%) and water handling systems (47.8%). Water handling systems (47.4%), daylighting (40.7%), and revegetation (40.2%) were associated with significantly lower manganese loadings. The decreases in acidity and sulfate loads associated with increasing the amount of alkaline material in the backfill indicates that the production of acid mine drainage can be retarded by adding large quantities of alkaline materials.

Jan 1, 2002

By B. Oraee

Tunnels as any other structures are affected by different loads and stresses. Generally, the loads on tunnels consist of both static and dynamic loads. These loads must both be considered in the tunnel design process. In this paper, the stability state of Jiroft water-transform tunnel is evaluated. Firstly, the in-situ stresses and then using Kirsch?s equations the induced stresses due to static loads in walls and crown of tunnel are calculated. Consequently, the strain caused by probable earthquake without considering the interaction between the concrete lining of tunnel and rock mass using seismic analysis is calculated based on free-field deformation. When the strain is determined, the simplified method of closed-form solution, Wang?s equations and Penzien?s equations are used to estimate the applied forces on the tunnel due to earthquake such as axial force and bending moment on a tunnel section taking into account the interaction of the tunnel concrete lining and rock mass. Results of this study show that the loads applied to the tunnel as a result of earthquake waves can be affect the stability of underground structures, especially long structures such as tunnels.

Jan 1, 2011

By T. H. Eyde

Worldwide production of natural zeolites during 2001 was estimated to be about 3.5 Mt (3.85million st). Construction and agriculture continued to be the major consumers. Estimated production in North America during 2001, including the United States, Canada and Mexico, was about 40 kt (44,000 st). In the United States and Canada, the zeolitic tuffs are ground, extruded or modified for use as adsorbents, desiccants, ion-exchange media and carriers. In Mexico and the rest of the world, the zeolitic tuffs are cut into dimension stone that is used in construction. Zeolitic tuffs are usually composed of the minerals clinoptilolite, mordenite or both. They occur in a variety of colors and are easy to cut and shape. And they have low thermal conductivity. This construction application is classified with dimension stone rather than with chemical and agricultural uses.

Jan 1, 2002

By L. Harris

The Yanacocha project is the first foreign investment in Peruvian mining since Cuajone during 1976. Three years after the project began, it has become the largest producer of gold from heap-leach operations in the world and the top producer in Latin America. The success of Minera Yanacocha SA (MYSA) opens a new chapter in Peruvian mining with the exploitation of its widely spread gold deposits. And it has attracted the interest of foreign investors in Peru’s mineral resources. Construction began on Aug. 1, 1992. The first gold bar was poured on Aug. 7, 1993 from ore from the Carachugo Mine. During 1993, Minera Yanacocha produced 2.5 t (81,000 oz) of gold and 9.4 t (304,000 oz) during1994 (40% above budget). Production was expected to exceed 15.5 t (500,000oz) during 1995 with the start-up the Maqui Maqui Mine.

Jan 1, 1996

By Pan Gao, Songyang Yin, Zhibiao Guo, Jinglin You, Yuhui Li

Under the geological conditions of the interaction of upper goafs and lower working face in deep mining, coal seam mining causes a large stress concentration, which may lead to large deformation of the surrounding rock and rock burst risk. The research reported herein is aimed to utilize the FLAC3D software to establish a three-dimensional numerical model and analyze the law of the surrounding rock stress evolution during coal mining under complex geological conditions. The simulation results reveal that the peak abutment stress reaches its maximum value at 20–30 m in front of the working face, about 1.8–4.3 times the original rock stress, and the peak stress is larger in the stable mining stage. Along the dip of the working face, the peak stress occurs about 8–10 m away from the roadway side. The upper barrier coal pillar and the interval coal pillar in order exhibit stress concentration areas of 142 m and 88 m. According to the law of the deflection stress distribution of the surrounding rock in the presence of various widths of the coal pillar, a 10-m coal pillar between the roadway and the adjacent goaf could enhance the stability of the roadway. For the stress concentration area, drilling holes with a depth of 20–25 m are utilized to reduce the pressure, and anti-impact supports are installed in the middle of the roadway. Due to the varying stresses of the rocks around the roadway, partition prevention and control countermeasures are capable of efficiently preventing the instability of the surrounding rock.

Mar 22, 2023