Search Documents

By E. D. Stephenson

As part of the British Steel Corporation?s development plan during the 1970?s, it was decided to concentrate its bulk steelmaking processes based on the BOS at 4 major Works with access to deepwater ore terminals, for the supply of high-grade imported ores. These 4 sites were at: - 1. Rarenscraig Works in Scotland where the ore terminal would be hilt at Hunterston on the west coast some 50 miles away. Bavenscraig was already an integrated Works but suffered from having to discharge ore 27 Glasgow tenxinus on the River Clyde, which could only accommodate vessels up to 25,000 tonnes. In the future, ore was to be unloaded at Runterston and shipped by a rail-link into Ravenscraig, The new ore terminal would have the potential to unload vessels up to 300,000 tonnes. - 2. Port Talbot Works in south Vales where the existing harbour was developed to discharge large ore carriers. This again was an existing Integrated Works and the benefits of the new harbour also applied to Llanwern Works which was another integrated Works some 50 dies to the east, which would now receive ore from Port Talbot.

Jan 1, 1980

By D. M. Carris

Since the Buffalo Creek incident in February, 1972, Federal and state environmental agencies have had the pressure on the coal industry in the Appalachian area to close the coal processing plant water circuits. In an attempt to comply with this requirement, Eastern .Associated Coal Corp. decided to install a vacuum disc filter system at its Kopperston plant to eliminate the tailings pond and reduce the amount of plant make-up water. It was recognized at the time that the plant static thickener tailings would be a very difficult slurry to dewater because of its unusually high clay content. The following is a case history of the Kopperston installation and the refinements Eastern has made in its vacuum disc filter operation to increase efficiency.

Jan 1, 1979

By N. Damiano, C. Zhou, B. Whisner, M. Reyes

"The Industrial Internet of Things (IIoT), a concept that combines sensor networks and control systems, has been employed in several industries to improve productivity and safety. U.S. National Institute for Occupational Safety and Health (NIOSH) researchers are investigating IIoT applications to identify the challenges of and potential solutions for transferring IIoT from other industries to the mining industry. Specifically, NIOSH has reviewed existing sensors and communications network systems used in U.S. underground coal mines to determine whether they are capable of supporting IIoT systems. The results show that about 40 percent of the installed post-accident communication systems as of 2014 require minimal or no modification to support IIoT applications. NIOSH researchers also developed an IIoT monitoring and control prototype system using low-cost microcontroller Wi-Fi boards to detect a door opening on a refuge alternative, activate fans located inside the Pittsburgh Experimental Mine and actuate an alarm beacon on the surface. The results of this feasibility study can be used to explore IIoT applications in underground coal mines based on existing communication and tracking infrastructure.IntroductionThe U.S. approach to health and safety in mining has historically been reactive in the sense that health and safety regulations and mandates have traditionally been passed as a result of tragic mining accidents. An example of this is the Mine Improvement and New Emergency Response Act (MINER Act) of 2006, which was passed as a result of several mining accidents where tracking of and communication with underground personnel were severely limited. While this reactive approach has led to the development and implementation of highly impactful safety interventions and safety practices, there exists a technological revolution that can shift the paradigm toward a proactive approach based on preventative methods: Internet of Things (IoT).IoT is the network of physical objects, or “things,” embedded with electronics, sensors and connectivity to enable that network to achieve greater value and service by exchanging data with the manufacturer, operator and/or other connected devices (Atzori, Iera and Morabito, 2010; Gubbi et al. 2013). It should be noted that IoT has been defined from various perspectives, and hence numerous definitions exist in the literature. The apparent ambiguity of the IoT definition might be due to the fact that IoT is syntactically composed of two terms: the Internet and things. The first word pushes toward a network-oriented vision, while the second tends to put the focus on generic objects. The traditional Internet can be viewed as an internet of computers, so things connected to the Internet are computers only. IoT extends the internet by allowing other generic things that are commonly found in daily life, such as refrigerators and cars, to be interconnected through the Internet, thus creating a bridge between the virtual world and the physical world"

Jan 12, 2017

By D. R. McConnell

The seafloor in the US Pacific OCS and EEZ is enriched to varying degrees in critical and economically important minerals such as nickel, manganese, cobalt, copper, zinc, REY (rare earth elements plus yttrium), titanium, vanadium, antimony, gold, and silver. These mineral deposits take the form of polymetallic nodules on the seabed, cobalt rich ferromanganese crusts on seamounts and ridges swept clean of sediment accumulation, and seafloor massive sulfides formed by hydrothermal systems at geologic plate spreading centers and volcanic margins. Each of these mineral deposits form on or near the deep ocean seafloor where water depths are typically 4000 m to 5500 m and on the seamounts and volcanic arcs that rise from these depths. Commercial interest in deep sea mineral deposits and the potential for collecting or mining them began in earnest in the 1970s but has been heightened in the last 20 years as the international framework for developing these minerals in International Waters has matured that has coincided with forecasted rapid rising demand for minerals to supply energy and manufacturing needs for the green economy. Compilation reports published by academia, government, and private companies are reviewed to assemble data and assess the prospects for deep sea marine minerals in the US Pacific OCS and EEZ. Key compilations were made by the Circum-Pacific Council and USGS in the 1980s and 1990s. These, together with recent (2023) efforts by USGS to compile geochemical data from USGS affiliated marine research sampling cruises from the 1980s and 1990s, historical data maintained by NOAA National Centers for Environmental Information (NCEI), and recent publicly disclosed results from ISA contractors are used to inform the known occurrence and prospectivity for polymetallic nodules, cobalt-rich ferromanganese crusts, and seafloor massive sulfides in the US Pacific OCS and EEZ.

Feb 22, 2026

By George Vranesh

Synfuels development in the upper Colorado River basin and the population growth attendant with such development demand sizeable quantities of water. Unfortunately, the water supply in the basin is limited and such limitation may impose a significant constraint on the development of the West's abundant energy resources. Although the water for the synfuels development will be governed by the law of prior appropriation adopted in the upper basin states, the authors point out that an apparently senior water right .my not deliver a firm supply of water. The federal and Indian Reserved Water Rights Doctrine, the Colorado River Compacts the Doctrine of Equitable Apportionment, and the federal and state environmental laws can all severely diminish the value of any given water right and the synfuels industry should take care to evaluate these factors in acquiring its water.

Jan 1, 1981

By Joseph D. Drew

Oregon Resources Corp. (ORC) has developed and permitted a new mining operation that incorporates a process design that will allow the unique paleo-beach placer deposits of southwestern Oregon to be extracted efficiently and economically, creating the only domestically mined source of a unique foundry grade chromite and specialty de-veining sand for precision casting. The operation will also provide an additional domestic source of garnet and zircon. Engineering design has been guided by the variable geology and mineralogy of the paleo-beach placer deposits as well as the need for a dry tailing scheme that resolves a lack of water resources at the placer locations and at the same time eliminates the need for slurry settling ponds, typical of paleo-beach placer operations in North America.

Jan 1, 2010

By L. R. Moore

Arsenic is among the list of major contaminants in mining aqueous waste streams. Though the elemental form is toxic, the aqueous oxyanions are more so. The most common forms of arsenic released during mining processes are arsenate and arsenite. The common treatment technologies to date can be summed up in these major categories: oxidation, coagulation, absorption, and media filtration. These methods can often involve many expensive processing steps that may also be limited by variables, such as total dissolved solids, other cations and anions, and the oxidation state of the arsenic. An innovative technology, falling in the absorption category, was developed that can successfully reduce such aqueous forms to a level below the EPA recommendations. This new technology offers a unique and viable solution which is transparent to the above mentioned limitations.

Jan 1, 2012

By A. Goulsbra, S. McAllister, R. Dunne

Since 1992, a tailings gravity re-treatment plant has been in operation at the New Celebration Gold Mine to recover aurifer­ous pyrite (Martins, Dunne and Gelfi 1991; Martins, Dunne and Delahey 1993). The gravity pyrite concentrate is ground in a Tower mill to liberate gold (average particle size around 25µm) prior to cyanide leaching. Although the re-treatment plant has met the predicted gold recovery, based on original laborat01y testwork, there is still room for improved gold recovery. This requires enhanced pyrite recovery, especially in the finer size ranges. The application of centrifugal gravity separators would seem to be an ideal means to achieve this criterion. In particular, the Falcon continuous centrifugal separator (Series C machines) would appear to be ideal for this particular duty. A testwork program to evaluate the application of the contin­uous Falcon to recover pyrite from New Celebration ores was unde1iaken over a six month period during the later part of 1997. The work involved laboratory batch testwork, followed by con­tinuous testing of the Falcon Cl0 (2tph to 3tph) and Falcon C40 (l00tph) units. A summary of the results from this evaluation program are provided in this paper.

Jan 1, 1998

By R. Y. Wan

Acid ferric sulfate solution has been used for heap and dump leaching of low-grade chalcopyrite ores and is being considered as a possible lixiviant for the hydrometallurgical processing of copper sulfide concentrates. For many years, researchers have attempted to explain the leaching behavior of chalcopyrite, since the reaction rate kinetics are extremely slow and seem to be significantly influenced by the nature of the reaction product. A summary of conclusions drawn from reported literature on chalcopyrite leaching is found in the paper by Munoz, Miller, and Wadsworth(1) and more recently by Dutrizac.(2) Lowe(3) and Jones and Peters (4) attributed rate control to a surface reaction. Linge,(5) Dutrizac,(6) Bauer,(7) and researchers at the University of Utah(1,8) reported that the reaction rate is limited by transport in the chalcopyrite lattice or through the elemental sulfur reaction product layer. Munoz et al.(1) presented a model, derived from the Wagner theory of oxidation, which is based on the formation of a protective sulfur layer with rate control by electron transport through the insulating sulfur layer. By utilizing Wagner's parabolic oxidation relationships, (9) the following equation was obtained: [ ] where a is the fraction of CuFeS2 reacted at time t, pB is the molar density of CuFeS2, do is the initial diameter of the particle, e is the electronic charge, s is the total electrical conductivity of the sulfur layer, and ?G is the Gibbs free energy for the reaction:

Jan 1, 1984

By D. G. Chedgy

Careful consideration is given to the type of cleaning equipment and control sys- teas to be used when selecting circuits for wash-ing fine coal (28M x 0 size fraction). However, the desliming, declaying and sizing procedures required to ensure efficient operation normally are not evaluated in sufficient detail resulting in disappointing system performance. This paper details desliming and dewatering circuit design which is extremely effective based on recent test data. The circuit maintains control of the 28M x 0 (declayed) size fraction with minimal misplaced material and maximized circuit efficiency. A discussion of circuit design parameters and control systems, as well as results from the testing program, are included in this text.

Jan 1, 1986

By G. Wheeler

Epithermal gold exploration in the last decade has developed useful models for exploring new ore districts in Oregon. In Eastern Oregon, disseminated gold occurs in epithermal deposits that have been pervasively silicified and brecciated. Many gold prospects staked since 1980 are in fluvial and lacustrine sandstone and conglomerate deposits. Clay alteration products and disseminated pyrite may be present. Vein filling calcite and thin to thick quartz veins are common. Late stage quartz forms pseudomorphs after calcite in many deposits. Arsenic, mercury and gold are geochemically anomolous but silver is usually not. The epithermal deposits are located in part of the Deer Butte Formation or equivalent units. Exploration criteria include the presence of Deer Butte Formation or correlative units and NW structures cut by N-S basin and range structures.

Jan 1, 1987

By Timothy P. Smirnoff, Tracy K. Lundin

INTRODUCTION The City of Phoenix, Arizona is located in the Phoenix Basin watershed which is prone to flash flooding several times each year. The runoff from these storms moves from the mountains in the north to the Salt River in the south. An extension of Interstate Highway 10 (1-10) will pass through the city east to west to form an Inner Loop through the downtown business district. PROJECT DESCRIPTION The I-10 Inner Loop extension will be a depressed roadway which would intercept the surface drainage of the Phoenix Basin and separate the watershed into two regions. To prevent flooding of the depressed roadway, runoff storm water collected from the northern half of the drainage area will be conveyed beneath the roadway to its natural outlet at the Salt River. A conveyance system composed of pressure tunnels beneath the city, shown in Figure 1, was proposed to achieve this goal . Table A presents the prominent features of each of the tunnels. This paper will describe geologic and engineering parameters specific to Phoenix which were used in the design of a series of tunnels to convey storm water from the I-10 Inner Loop to the Salt River. The design of tunnel initial and final support is described along with support and construction methods used by the Contractor.

Jan 1, 1985

By Charles T. Holland

INTRODUCTION Insofar as I am aware, the term rock mechanics was not in the English dictionary in 1930 when I started my graduate program at West Virginia University. Hence, I never thought that I was undertaking studies in rock mechanics when I undertook to write a thesis on the physical properties of West Virginia coal. In this case, the subject was primarily concerned with the compressive strength of coal, the elasticity of the coal, the physical weathering properties of the coal and its friability. These days investigations of rocks pertaining to such properties are included in the term "rock mechanics". Other than this aspect, the principle interest in this part of my program was that I became interested in the strength of coal from the standpoint of structural purposes, and also became cognizant of its elastic properties as well as its energy storing properties. This research also tied in with a remark that Professor Lawall made in a Mining Methods class in 1928 when he remarked that a peculiar thing was happening in the southern part of West Virginia, namely, in the Pocahontas coal field. His remarks were to the effect that pillars were blowing up in the mines and when asked why he replied the cause was not known. The failure of three-inch coal specimens, especially those in stronger coal, in non-hydraulic actuated testing machines was reminiscent of his description of those pillar bursts or bumps.

Jan 1, 1971

By T. J. Close

On September 10, 1991, Secretary of the Department of Interior Manuel Lujan deleted the Silver Peak Range North Wilderness Study Area from the list of U.S. Bureau of Land Management lands in Nevada to be considered for wilderness designation. This decision was based in part on the U.S. Bureau of Mines mineral investigation of the wilderness study area which found that it has indications of precious metals resources. The following is a summary of the results of that mineral investigation. The study area lies between the Silver Peak and Dyer mining districts of west-central Nevada. The Silver Peak mining district, to the east, has a long mining history dating back to 1907 when precious-metals-bearing veins were discovered. The major producer in the Silver Peak district was Sunshine Mining Company's Sixteen-to-One silver mine. During the Bureau's study the Sixteen-to-One mine was operating; it has since been idled due to low silver prices. Precious metals-bearing veins were discovered in the Dyer district, to the west of the study area, in the 1860's. Mineral activity in Dyer district consisted mainly of prospecting. The Silver Peak study area itself has no mining history and contains only a few mining claims, but the Bureau examined 13 mineralized sites, most previously unknown and unclaimed. These sites are along two zones that cross the study area from the Silver Peak to the Dyer mining district. The two zones transect a volcanic center of fractured and altered rocks that contain epithermal veins of quartz, calcite, and jasperoid with gold, silver, and base metals. At the surface these veins are poorly defined and poorly mineralized. The more than forty veins examined in the study area are as thick as 17 feet and as long as 1,000 feet. Samples from surface exposures of these veins contained as much as 0.02 ounce per ton gold, 2.1 ounces per ton silver, 1.0 percent copper, 2.6 percent lead, and 0.4 percent zinc. Analyses of the Bureau data disclosed no vein large enough or of high enough grade to be classified a mineral resource. However, most do have indications of silver-and gold-bearing resources at depth. Subsurface exploration had to be done on the vein at the Sixteen-to-One mine to outline reserves (a vein averaging about 22 feet thick and containing 6-to 7-ounces per ton silver); the same is true of veins in the Silver Peak Range North Wilderness Study Area.

Jan 1, 1993

By J. D. McKay

The Bureau of Mines devised a column flotation technique using either fine or coarse bubbles and compared it with conventional flotation on a Montana chromite ore. On deslimed ore, fine-bubble column flotation produced a 44.7-pct-Cr203-grade rougher concentrate with 87-pct recovery, compared with 43.8- and 43.5-pct-Cr203-grade rougher concentrates with 85- and 77-pct recovery for coarse-bubble column flotation and conventional flotation, respectively. On undeslimed ore, coarse-and fine-bubble column flotation produced rougher concentrates containing approximately 41.5-pct-Cr203 with 95-pct recovery, exceeding conventional flotation which produced 35.6-pct-Cr203-grade concentrates with 87-pct recovery.

Jan 1, 1985

By Christopher Haycocks

The growth of computer and ground control technology in recent years, combined with an urgent demand for low-cost fossil fuels and mineral resources, has set the stage for full-scale utilization of computers in mine planning. Steeply rising production costs and the need to preserve the environment are placing great demands on engineers to improve their mining efficiencies, which can best be accomplished by applying the full capabilities of the computer. Pressure to develop and perfect programs with an immediate potential for improving mine de- sign, reducing mining costs and extending the viable coal reserves of the country has already come to bear in the form of exploding energy requirements, environ- mental considerations and the visible limitations of other energy sources. The computer program discussed in this paper, RAMPLAN (Rock Mechanics Applied to Nine Planning), was constructed as part of a continuing effort at Virginia Polytechnic Institute & State University under the sponsorship of the Office of Coal Research to develop a suite of programs to benefit the mining engineer in improving mine design and evaluation techniques. This program averages out structural data values obtained from randomly placed or gridded point sources across a mining property and uses these values in structural design equations. The basic purpose of the program is to provide accurate estimates of mineable tonnages, based on a realistic assessment of structural conditions existing in the deposit, for use in subsequent evaluation programs. Program output, however, also provides sound engineering data for the mine planner to use in planning and laying out new properties. Mining dimensions produced by the program provide a good starting point for initial layouts; and as more refined procedures are developed for increasing and improving the quality and quantity of information from boreholes, this information may be used with increasing confidence. The rock mechanics principles utilized in the program are generally well-established with full details provided to the user. To produce meaningful results extensive input data, obtained from exploration borehole core data, outcrop sampling points, or mine samples, are required. To assist the engineer, details of the types of tests that should be conducted have been listed. By including all of the ground control equations in the program the otherwise long and tedious calculations can be performed easily and quickly, and the work can provide the basis for a more detailed ground control study. The program is written in Fortran IV Level G to run on an IBM 3701155 ASP and requires 156K storage.

Jan 1, 1973

By S. Mojeddifar, N. Ostadmahdi Aragh, M. Hemmati Chegeni

This work integrated selective principal component analysis (SPCA) with a singularity fractal model to map hydrothermal alterations of argillic, phyllic, and propylitic in the north-west of Kerman city in Iran. SPCA results were provided for short wave infrared (SWIR) bands of the Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER) sensor tomap phyllic and propylitic alterations. Also, the bands 5–7 were applied to map the argillic alteration zone. SPCA results could present useful information for alteration mapping but it does not show the purest pixels of alteration. Therefore, a fractal model of singularity was applied to highlight the different alteration pixels in the Kerman Cenozoic magmatic arc (KCMA). Thus, the singularity index of different hydrothermal alteration zones was produced. Comparing the obtained results with the field data showed that Kader, Serenu,Meiduk, and Abdar deposits were acceptably identified by alteration mapping. Also, it seems that the singularity index could not discriminate the hydrothermal alterations of argillic and phyllic. The same spectral signature of kaolinite and muscovite minerals is the main reason for misclassifications.

Jul 20, 2020

By A. E. Halim, J. F. Brune

The 2006 Sago, Darby, and Aracoma mine disasters in the United States (US) forced the US government to implement the 2006 MINER Act and additional regulations that require all US underground coal mines to install and maintain refuge chambers to manage entrapment emergencies, in particular, fires and explosions. However, there is a debate on whether barricading in refuge chambers is a good strategy to survive such emergencies. Australian coal mines are not required to use refuge chambers and, instead, have adopted a strategy that focuses on instructing and training miners to self-escape to the surface. This paper analyzes merits and problems of using refuge chambers and self-escape to the surface to manage emergencies in fires or explosions in an underground coal mine. The authors found that the use of refuge chambers may not be the best strategy during extensive fires or when multiple explosions happen. In these situations, mine rescuers are unlikely able to extract miners who are sheltered in chambers and conversely, self-escape may save more lives than sheltering. Chances for successful self-escape are further improved by regular, externally assessed training such as Level 1 Emergency Exercises required in the Australian State of Queensland. These exercises put pressure on mine operators to ensure and maintain the effectiveness of their emergency management system.

By J. J. McClellenand, R. A. Jankowski

Face ventilation and water sprays are the primary controls used on continuous miner sections to protect workers from respirable coal and silica (quartz) dust. Laboratory tests were conducted by the U.S. Bureau of Mines to determine the impact on respirable dust concentrations when increasing airflow from 3000 to 9000 cfm (1.42 to 4.25 m3/sec), water flow from 15 to 35 gpm (0.057 to 0.132 m3/min) , and water pressure from 80 to 200 psi (5.52 x105 to 1.38 x106 pa). The effective limits for each control and interactions between these controls were of particular interest. Initial analysis concentrated on defining the impact of the control parameters on the respirable fraction of the feed dust, which was a blend containing 90% coal and 10% quartz. Gravimetric sampling indicated that airflow had the most significant individual impact on respirable dust levels and resulted in reductions of 99% at the operator and 57% in the return. Regression modeling was used to predict dust concentrations at the operator and in the return. Significant interactions were observed between control parameters and often, defined the level for a control parameter where increases above that level did not significantly benefit dust control. Increasing airflow to 8400 cfm (3.96 m3/sec), water flow to 25 gpm (0.095 m3/min), and water pressure to 140 psi (9.65 x105 Pa) typically provided respirable dust reductions at both sampling locations, while optimizing use of control resources. After determining these relationships for the total respirable fraction, selected filters were analyzed for quartz content to define the impact on the quartz component of the feed dust. For the individual control parameters, airflow again had the most significant impact and resulted in reductions of 98% at the operator and 26% in the return. Regression modeling of the quartz concentrations indicated that no significant interactions between control parameters were present. At the operators location, airflow was the only parameter identified as having a statistically significant reduction for quartz dust. A reduction in quartz approaching 95% was observed for increasing airflow to 6000 cfm (2.83 m3/sec). Increases above 6000 cfm had little additional impact. In the return, a linear relationship between control parameters and quartz levels was observed with reductions of approximately 27% predicted for increasing any one control parameter to its maximum level. The synergistic impact of increasing all control parameters to maximum levels resulted in a maximum predicted reduction of 81%.

Jan 1, 1991

By Akram Marseet, Andrew J. Petruska, Rik Banerjee

Underground mine roof bolting is a crucial operation for miners’ safety and mine sustainability. Since roof bolting is a manual or human-supervised operation, miners’ safety is at risk due to dust or rock falls. Traditional machine learning algorithms have shown limitations to detecting drillable areas, mainly due to harsh lighting conditions. The authors propose an adaptive deep-learning framework for autonomous roof bolting. The proposed framework is based on implementing a binary semantic segmentation algorithm on color images to classify pixels that belong to rock from those that belong to non-rock. Significantly, the proposed framework implements deep learning semantic segmentation on images from traditional and neuromorphic vision sensors in underground mines. The performance of the proposed model shows an impressive accuracy level of at least 98% at a low number of training epochs with smooth learning curves. The high accuracy enables the implementation of autonomous roof bolting, greatly improving miners’ safety and operational efficiency while reducing human exposure to safety hazards. This research will advance the use of deep learning in mining automation and has the potential to revolutionize the traditional mining industry.

Feb 1, 2024