Search Documents

By Nasser Madani, Yerbol Tussupbekov, Sergei Sabanov, Zarina Mukhamedyarova

A case study was conducted on a metal mine operating in Kazakhstan, in which problems were associated with use of a complicated and outdated ventilation system and its high expenses. The mine needs to reconsider its existing ventilation system and identify the risks associated with operational losses when using this ventilation system. The aim of this study was to develop an efficient risk analysis method capable of estimating operational risks and financial benefits of the existing mine ventilation system. The developed risk analysismethod considers ventilationmodelling, riskmodelling, and financialmodelling.Ventilation modelling comprises ventilation simulation and ventilation financial simulation. In risk modelling, the number of risk events occurring with the use of existing ventilation system and the operational losses during these events is estimated. Financial modelling considers operational losses and ventilation financial simulation benefits and uses a dynamic cash flow model to estimate how cost variability influences the cash flow. As a result, the improved ventilation system attains an additional NPVa ranging from 3.2 to 8.5 million US$ at the corresponding defined probability of 90%. The results of this study reveal that the developed risk analysis method can efficiently estimate the financial benefits of ventilation modelling and consider risk events and their total operational losses associated with use of the existing ventilation system. This approach provides a range of possible outcomes and helps with deciding whether the ventilation system is appropriate or whether it should be updated to better suit the project financial benefits.

Jun 3, 2020

By C. L. Jiang, B. K. Parekh, X. Shao

Among the impurities present in phosphate ore, dolomite is the most difficult to remove. This is because dolomite and phosphate have similar chemical compositions and because the dissolved species of dolomite is adsorbed on the surface of the phosphate mineral. A new amphoteric surfactant was found to be a suitable collector for the separation of dolomite and phosphate. Flotation results showed that the new amphoteric collector had a high flotation selectivity for dolomite over a wide pH range. studies on the flotation of francolite and dolomite in each other's supernatant demonstrated that the dissolved ions had little effect on the selectivity of the new collector. It was found, however, that the dissolved ions were detrimental to the flotation separation using sodium oleate as collector. From a mixture offrancolite and dolomite containing 26.2% P2O5, a phosphate concentrate containing 35.2% P205 with a 90% recovery was obtained using 290 g/t of the amphoteric collector. The rejection of MgO was 81.41 %.

Jan 1, 1999

By James J. Olson

Most of the projects summarized in this paper are funded under the Bureau's Advancing Metal-Nonmetal Mining Technology program and are part of the in situ mining subprogram coordinated at the Twin Cities Mining Research Center. The borehole mining equipment development, are funded under the Bureau's Advancing Coal Mining Technology program, is essential to accelerated progress in the in situ mining subprogram, and some background information on this concept is included. The initial in situ research projects started in 1971-72 evaluated some of the critical blast design parameters for in situ copper leaching. The present program totals about $1 million per year and includes in-house research projects, cooperative (cost-sharing) projects with the mining industry, and research and development contracts. Two different extraction schemes are under investigation: inplace leaching and borehole (or slurry) mining. The principal commodity targets for the Bureau's improved in situ mining technologies include copper, uranium, coal, and potash. The principal purpose of this paper is to inform the mining industry of the in situ mining research recently completed or being conducted by the Bureau of Mines. In addition the Bureau encourages companies to comment on the program accomplishments as well as offer suggestions on top priority research needs for improving the in situ mining methods described in this paper.

Jan 1, 1977

By W. R. Reed, G. W. Luxbacher

Mine worker exposure to respirable coal dust and silica dust can result in coal workers’ pneumoconiosis and silicosis which are occupational respiratory diseases that have no cure and are ultimately fatal. In 2021 the Mine Safety and Health Administration reported just over 11,000 operating metal/nonmetal mines with the potential for silica dust exposure for just under 200,000 miners. The National Institute for Occupational Safety and Health (NIOSH) conducts respirable coal and silica dust research associated with mining through its Office of Mine Safety and Health Research. NIOSH respirable coal and silica dust research began under the U.S. Bureau of Mines (USBM), which initially examined silica dust, progressing to include coal dust, with a stronger focus after 1969 with the passage of the Federal Coal Mine Health and Safety Act. A review of extramural research to develop real-time respirable silica dust monitor is presented along with a brief history of silica dust regulation.

Feb 1, 2024

By P. Clifford

FIPR-sponsored research will playa critical role in enhancing the competitiveness of the Florida phosphate industry as ore grade declines and environmental restrictions tighten. FIPR's program seeks to improve surface mining and pipeline transportation while reducing the energy cost for pumping phosphate matrix. The development of a reliable on-line analyzer and a modern process control strategy will result in improved processing efficiency. Significant improvement in overall efficiency will also be realized as the industry adopts column flotation technology. Economic acidulation of high-Insol rock will allow the industry to adopt simplified flotation flowsheets thereby reducing operating costs. Various applications of phosphogypsum would save the industry millions of dollars in constructing and closing gypsum stacks.

Jan 1, 1998

By J. Herbst, J. Groppo, A. Noble, R. Q. Honaker

"Coal and coal byproducts produced annually contain a sufficient amount of rare earth elements (REEs) to meet current U.S. demand. The REEs exist in the form of minerals, ion-adsorbed elements associated with clays, and chemically bonded elements within the organic coal matrix or host mineral. Researchers at three universities collaborated to evaluate the effectiveness of existing physical and chemical concentration processes for the recovery of the REEs. The efforts found that physical separation processes can increase the total REE content in the thickener underflow material collected from a Central Appalachian coal cleaning facility from around 300 ppm to values greater than 17,500 ppm on an ash basis. Leaching followed by solvent extraction was found to be the most effective to recover the REEs from coarse middlings materials collected from multiple coal basins, as indicated by recovery values exceeding 80 percent. Based on material characterization data and process evaluations conducted for several potential feed coal sources, economic recovery of the REEs will require byproduct production of both clean coal and REE concentrate using a process flowsheet that is unique for each source. IntroductionRecent studies initiated by the National Energy Technology Laboratory showed that U.S. coals contain significant amounts of rare earth elements (REEs), suggesting that rare earth minerals (REMs) and/or REEs can be produced as byproducts (Ekmann, 2012). According to the report, the richest source of REEs is the Central Appalachian coal. At present, there are 208 coal preparation plants located in the region consisting of areas within the states of West Virginia, Kentucky, Pennsylvania, Virginia, Alabama and Tennessee, with a total capacity of 166,495 t/h, or more than 1 Gt/y (Fiscor, 2014). If only a portion of these plants are retrofitted with advanced separation processes, the U.S. coal industry would become a significant producer of REE concentrates as byproducts. An inherent advantage of becoming a byproduct producer of REEs is that no mining cost needs to be part of the production cost."

Jan 1, 2017

By Calvin L. Stevenson

The probability of a particle passing through a maze is predictable and consistent. This principle may be utilized to effect a particle size separation of materials by presenting a physical maze to a stream of material that will allow the fine particles to pass, while deflecting the coarse particles. A maze is effective even though all apertures encountered are many times larger than the particles being separated. By designing a machine that allows the probability parameters to be controlled and varied without changing physical dimensions, probability sizing becomes a useful tool for the separation of granular materials.

Jan 1, 1967

By Brian Garrod

Increasing use of pressurized-face tunnel boring machines in North America has produced a similar increase in the application of precast concrete tunnel linings. Where a pressurized TBM is needed, immediate ground support and ground water pressure resistance is also required. A segmental lining installed within the TBM tail shield provides the only available means of providing such a sealed lining. This paper addresses new developments in North America in lining applications and design. For the purposes of this paper, a precast concrete tunnel lining is defined as a tunnel lining constructed using precast concrete segments that are assembled into a lining ring. The lining rings are connected adjacent to each other to form a tunnel lining. Each segment has a sealing gasket around it so that when the lining is completed, it provides a fully waterproof lining system. The ring is erected within the tail shield of the TBM and the annular gap around the ring is filled with grout as the machine moves forward. The ring is not expanded and normally provides the finished lining of the tunnel with no requirement for a second pass lining. The TBM has a series of hydraulic rams that push on the leading edge of the segmental lining to provide the sole system of forward propulsion for the machine. The rings are tapered, being longer on one side than the other. This allows the rings to be installed either on a curve or in a straight line depending on the rotational position of the rings.

Jan 1, 2008

By M. G. Mudrey

Considerable potential for metallic mineral resources in the lower Proterozoic rock of the Lake Superior region exists (Mudrey and Kalliokoski, in press). Most of the identified resources occur within a 2.0- to 1.9-b.y.-old lithotectonic assemblage characterized by extensive sedimentary strata in the north and thick volcanic se- quences in the south, all deposited on a two-terrane, composite basement of Archean age (DeMattis, 1989). Since the late 1960s, measured resources of nearly 90 Mt (100 million st) of typical volcanogenic massive sulfide at eight localities in Wisconsin have been discovered. The largest of these, near Crandon, contains about 61 Mt (67 million st) of ore averaging 5.6% zinc, 1.1 % copper, and 0.5% lead. Although none of these properties are in production, estimates by Mudrey (1978) suggest that Wisconsin could become a major contributor of newly mined zinc and copper in the United States. These discoveries and uranium and gold discoveries in the Canadian Precambrian are what have led to in- creased metallic mineral exploration throughout the northern half of Wisconsin (Fig. 1). In this chapter, we discuss the geology and legal framework in which the Proterozoic volcanogenic massive sulfide deposits were found. Exploration activities for other metals have generally been negative, and have been background noise for the legislative activities related to the massive sulfide discoveries. Uranium exploration has been consistently negative, although several different environments have been assessed. Other metal discoveries. such as titanium/vanadium, have been subeconomic.

Jan 1, 1991

By Dennis K. Mortensen

The warm southwestern desert of Arizona is an ideal location for ASARCO's new Sacaton Unit. The climate of this arid region played a major role in the design considerations of the Unit's crushing and concentrating facilities. Low yearly rainfall and relatively high yearly temperatures are a combination that was taken advantage of when designing the surface facilities. The plantsite, located due west of the mine pit, is in an area originally covered with sparse desert vegetation, underlain to an average depth of 125 feet by desert alluvium. The entire plantsite area slopes gently to the southwest at approximately 1%. Ground conditions at the plantsite area were not acceptable for construction due to the collapsability of the wetted soil when under loaded conditions, Overburden from the pit area was used to form the foundation for the entire plantsite. This waste material, entirely devoid of rock, was placed and compacted to an elevation approximately 20 feet above the desert floor. Elevating the plantsite by filling with waste material not only provided an adequate construction foundation but also eliminated the possibility of flooding from run-off in the surrounding desert areas.

Jan 1, 1974

By T. Brozell

"Communities near sand mines and processing facilities in Wisconsin have raised concerns regarding possible exposure to ambient respirable (PM4) crystalline silica. Fenceline PM4 (particulate matter captured with a 50 percent cut size of 4 micrometers aerodynamic diameter) crystalline silica concentration data were compiled at Fairmount Santrol Inc., Mathy Construction Inc. and U.S. Silica facilities. The long-term average PM4 crystalline silica concentrations ranged from 0.05 to 0.45 micrograms/m3 when sample values below the limit of quantification were treated as zeros. All of the long-term average concentrations were less than 20 percent of the Minnesota Department of Health’s and California Office of Environmental Health Hazard Assessment’s PM4 crystalline silica chronic reference exposure level of 3.0 micrograms/m3. The measured concentrations were consistently within the local background concentration range.Air Control Techniques P.C. compiled the sampling data using Thermo Fisher Scientific Inc. Partisol 2000i PM2.5 samplers meeting the requirements of 40 CFR Part 50, Appendix L. These samplers were adapted to capture particulate matter with a 50 percent cut size of 4 micrometers. The use of polyvinyl chloride filters allowed for crystalline silica X-ray diffraction analysis by NIOSH Method 7500. The combined use of adjusted PM2.5 filter-based samplers with Method 7500 crystalline silica analyses provided for a highly sensitive limit of quantification of 0.31 micrograms/m3 of PM4 crystalline silica.BackgroundIn 2005, the California Office of Environmental Health Hazard Assessment (OEHHA, 2005) adopted a 70-year chronic reference exposure level (REL) for PM4 (particulate matter having aerodynamic diameter of 4 micrometers or less) crystalline silica. The REL was extrapolated from occupational hygiene epidemiological studies, essentially all of which were based on in-plant PM4 crystalline silica measurements. No well-established ambient sampling technique for PM4 crystalline silica was available at the time that OEHHA adopted its REL. The personal samplers used for the National Institute for Occupational Safety and Health (NIOSH) Method 0600 in-plant sampling of employee exposure were designed for concentrations higher than ambient levels. The limit of quantification (LOQ) of PM4 crystalline silica on NIOSH 0600 filters was too high for the effective sampling of ambient air."

Jan 1, 2015

By Robert W. Row

The run-of-mine coals in the U.S. being fed to coal cleaning plants have become increasingly finer due to the adoption of modern, mechanized mining methods, and economics are dictating that finer fractions, as well as the coarser fractions, be cleaned. Traditional dewatering methods (vacuum disc filters and centrifuges) are proving inadequate for preparing fine refuse for disposal or fine coal product for downstream handling. The Electric Power Research Institute has been supporting research into the nature and limitations of mechanical dewatering, and novel ways of improving it. The efficiency of various silicone-based chemicals at aiding dewatering was investigated, and it was shown that the final moisture content of hydrophilic coals after vacuum Filtration could be reduced by 1 to 5% with up to 40% increase in filtration rate by addition of one of several of these silicones. EPRI also has an on-going program at its Coal Cleaning Test Facility to investigate the performance of the Larox pressure filter in comparison with that of the disc filter and solid bowl centrifuge. While improvements to the dewatering performance currently being obtained in existing operating plants by such means are achieveable, a fundamental study has shown that, regardless of changes in operating conditions, there may be a limit to the lowest cake moisture content attainable by mechanical dewatering of a given sample of coal fines. Determination of this limit for a specific coal would be useful in designing facilities to dry and handle it.

Jan 1, 1984

By Raúl Castro, Marco Vera, Alfonso Ovalle

The underground mining evolution for block cave mines in Chile and worldwide has made important strides in the last decades. Nonetheless, reserves determination in the initial stages of these types of projects—mainly for long-term planning—is not studied in as much detail as it should be, especially regarding the impact on the final value of the enterprise. Today, the first estimation of the size of a block cave mine, typically expressed in tons, tends to determine very large footprints and ore bodies. The resulting large-scale mine is obtained by applying the marginal cut-off grade (COG) to determine reserves. Yet, in many cases, it is possible to obtain an equal or higher benefit, extracting fewer reserves in less time, with a smaller active area, which significantly reduces the project’s uncertainty. To explore scenarios obtained by applying a higher marginal COG in the initial phases of the project, the Hill of Value methodology is used to estimate the net present value (NPV) in relation to the production rate and the COG. However, the application of this methodology considers certain simplifications that generate results which are not completely satisfactory in specific cases. This paper suggests an improvement of this method to obtain more reliable results regarding determination of a COG profile that will optimize the NPVof a block-cave project. The methodology was developed and applied in a massive polymetallic deposit with zinc, lead, and silver mineralization, corresponding to a real block caving project. The methodology provides NPV results that differ by approximately 15% in comparison to the real mine plan, while also being considerably simpler and faster to calculate. In summary, the proposed methodology provides a reasonable and fast procedure to estimate higher than marginal COG that increases the NPV of block cave mine projects.

By Neil and Associates

Seismic tomography is one of several additions to the suite of geotechnical engineering tools for use in various underground rock and mineral geologic structures. Seismic tomography is a method for reconstructing a cross section of an object based on attributes of seismic energy that have been transmitted through the object. The in-seam seismic tomogram provides a dataset that can be graphically portrayed in a color-coded format that is then used to infer relative stress concentration (Fig. 1). During the past several years, the US Bureau of Mines (USBM) at its Denver, CO and Twin Cities Research Centers in Minnesota funded several innovative hardware and software developments. These were directed toward use of in-seam seismic tomography for underground geologic strata evaluations. These preliminary investigations have matured into well-defined and field-proven technical advances for improving ground-control decision making in the mining industry.

Jan 1, 1996

By A. N. Pritchard

The development of vibrating screens over the last century has seen many variations to suit the exacting requirements of industry. Indeed, as each year passes, industry has presented the challenge to screen manufacturers of supplying larger machines than those used in the past and the question is often posed - what is the maximum limit? Not only must size or screen area be considered but excellence of performance in terms of screening efficiency must be maintained or maximized.

Jan 1, 1983

By Edward DeLilla

For the past 30 years, surface mines have moved toward more highly mechanized, automatic systems that continuously mine overburden and ore to increase productivity, lower operating costs and minimize manpower needs. To achieve these goals, mine operators must be involved in every step of the machine procurement process. Several factors are involved in making the machines operate economically and efficiently: -Prudent engineering. -Proper planning. -Realistic feasibility studies. -Effective specification. -Thorough training of the mine personnel.

Jan 1, 1994

By L. W. Saperstein

Public Law (PL) 95-87 contains explicit demands for land use planning in its reclamation and designation sections. Both sections require recognition of local land use plans; however, they are not well integrated. Accommodation to these planning requirements affords an opportunity to create better links among local land use planners, the state's permitting authority and designation office, and mine designers. Mining companies should take a more positive interest in local land use plans and in resource inventories. States should consider handing down to local government the responsibility for accepting mine permit applications and designation of unsuitability petitions.

Jan 12, 1983

By A. M. Elmahdy

An amphoteric collector was tested for dolomite removal from phosphate ore. The effects of some operating parameters and their significance on the flotation of dolomite were studied using statistically designed experiments. The parameters studied were impeller speed, pH and collector dosage. Analysis of the results showed that pH is the most significant parameter. Moreover, a concentrate containing 0.53% MgO and ~31.1% P2O5 with a recovery of ~ 90% can be achieved at optimum values of studied parameters, i.e., a pH of 12, an impeller speed of 1,000 rpm and a collector dosage of 2.5 kg/t.

Jan 1, 2007

By David Mast, Irwan Halim, Seung Han Kim

Nowadays more infrastructure tunnel projects are procured using design-build method. In this environment, the Owner’s engineer would typically provide performance requirements for the design-builder, and the Contractor’s designer would work with the contractor to design the tunnel lining based on the Contractor’s means and methods and manufacturing process. This paper will describe the typical requirements provided by the Owner based on its design objectives, and the means and methods by the Contractor that would significantly impact the design. Project examples and recommendations for Owner’s requirements will be provided that can optimize the design and still achieve the Owner’s performance objectives.

Jun 13, 2021

By F. B. Kuhnow

When performing blasting operations in open pit settings, energy is released and transmitted through the geology. Some negative effects can have significant impacts on mining operations and adversely affect mine production. This technical paper presents recommendations for blast design to prevent damage due to ground motion from blasting on adjacent concrete structures of underground operations. The paper includes a case study describing a problem regarding an open pit mine expansion and asks whether production blasting will damage concrete shaft structures due to blast stress waves and blastinduced ground motion. Based on the results, a set of criteria is provided to implement in current and future mining operations that involve blasting near underground concrete structures. A set of techniques on how to improve vibration levels for safe operations is also presented. Knowledge of particle velocity and wave propagation for site-specific circumstances to determine a safe level of vibration is recommended. Emphasis is placed on making use of electronic detonators and early delay detonators to achieve successful levels of vibration. A dynamic analysis is necessary to determine if vibration from blasting can damage the concrete shaft structure. When reinforced concrete structures are subject to blast loading, both concrete and steel are subject to very high strain rates. As opposed to static loads, when subject to high strain rate loads these materials increase their strength significantly. In fact, they increase by more than 50% for reinforcing steel, by more than 100% for concrete in compression, and by more than 600% for concrete in tension. This finding is of significant importance in mining operations because it allows an increase in flexural capacity of individual members as a result of high strain rates. Therefore, an elevated ground vibration (PPV) or particle velocity is permissible when blasting takes place near concrete structures.

Jan 1, 2014