Search Documents

The ventilation conditions at the underground coal mines are influenced; first: by the disturbances of the natural nature (barometric pressure, methane liberation, etc.), and second: by the disturbances caused by the production process. The major goal of this study was to determine the changes of the ventilation parameters, such as the flow, pressure and methane concentration around the longwall panel, particularly, along the longwall face due to the shearer operation (motion). It is well known from the practice, that the movement of the shearer influences the ventilation parameters around the longwall panel, including the gob area. Until now, these data were gathered in a single or multiple locations at the different time. However, only the simultaneous measurements of all of these values allow seeing the time dependent interrelationships between measured parameters. To be able to show these interrelationships, special experiments, described in this paper, were carried out by the author. These experiments were prepared and executed at the BUDRYK Coal Mine in Poland. During each experiment a simultaneous measurements and monitoring of the barometric pressure, air velocity and methane concentration at the different locations along the longwall face, were performed. The investigation was possible by using a special setup of instruments with a short sampling time, i.e., within 2 seconds. The monitoring of the absolute pressure was conducted by using the digital barometer µBar, developed by EMAG, based on the SETRA pressure transducer, model 470. The velocity of air was measured using the electronic vane-anemometers, developed by IMG-PAN. The methane concentrations were measured using methanometers as the part of the EMAG automatic gas monitoring system. The investigation data confirmed that disturbances due to the operation (motion) of the shearer at the longwall face have a local character. It could be also seen that a large diameter shearer (compared to the total cross-section area available for the air flow) is acting as the piston compressing the air (the overpressure) ahead of the shearer. This fact affects the methane mixing process and flow patterns in the vicinity.

Jan 1, 2009

By Yi Luo, FENGLIANG WU

Explosions and fires originated from longwall gob due to the formation of methane-air mixture have been a severe threat to coal miner’s lives.Many numerical studies on coalmine fire and explosion hazards have focused on the airflow in roadways and mine gobs. However, most of these studies isolate the gob from its surrounding roadways, and the network analysis and the CFD method are applied independently tomodel the two classes of airflows. This approach greatly limits the ability of simulatingmine ventilation flow, especially unable to consider the effects of gob boundary conditions on air exchange between the gob and the surrounding airways. An innovative finite tube method (FTM) is developed to couple the one-dimensional mine ventilation network (MVN) and the 2D/3D gob flow field (GFF). In FTM, GFF is discretized into a finite number of flow tubes each of which is formed by any two adjacent stream lines. These tubes, representing the gob’s field flow, connect the MVN into a new coupling network. To solve the coupling model betweenMVN and GFF, an iterative solution technique is developed inwhich the MVN analysis is used to evaluate the boundary pressures for GFF simulation and in turn the FTM feeds the GFF results back to the coupling network. Based on the FTM approach, a model for gas migration in gob has been established for delineating the hazard zones of explosive methane concentration and spontaneous combustion. A computer program is developed to implement the FTM simulation. An illustrative example with five flow tubes representing the GFF is created to verify the stability and convergence of the FTM solution process. A simulation example also indicates that the accuracy of FTM is improved by 12% compared with previous method. Results of an application case show that the program is capable of quantitatively evaluating the gob’s risk zones prone for spontaneous combustion and gas explosion as well as performing risk analysis for various ventilation scenarios.

Jul 10, 2020

By Yao Yevenyo Ziggah, Victor Amoako Temeng, Solomon Evans Kweku Koomson

Tyre hours/life deficit is a major operational challenge facing the mining industry which adversely affects materials production and costs. An accurate forecast of the tyre life is key in addressing this menace. This study for the first time employed the hybrid intelligent technique by utilising three metaheuristic optimisation algorithms, including particle swarm optimisation (PSO), genetic algorithm (GA), and whale optimisation algorithm (WOA), as trainers for the parametric weights and biases to optimise multilayer perceptron neural network (MLPNN) for enhancing prediction of on-site dump truck tyre life in the mine. Four hybrid models known as PSO-MLPNN, WOA-MLPNN, GA-MLPNN, and BP-MLPNN were developed using a total of 157 tyre dataset records obtained from a surface mine in Ghana. In assessing the prediction performances for the models developed, five statistical performance metrics of variance accounted for (VAF), Nash–Sutcliffe efficiency index (NASH), coefficient of determination (r2), mean absolute percentage error (MAPE), and correlation coefficient (r) were utilised. Moreover, ranking, uncertainty analysis and Bayesian information criterion (BIC) techniques were utilised to establish the most effective hybrid model, whereas sensitivity analysis was conducted on the input parameters. Results achieved showed that PSO-MLPNN was the best for prediction because it had the least MAPE value of 1.196% and relatively high values of VAF (99.642%), NASH (0.996), r2 (0.996), and r (0.998). Besides, PSO-MLPNN had the best selection criteria values of 6, 7.1725, and 444.834 for the ranking, uncertainty analysis and BIC respectively. Hence, PSO-MLPNN is recommended for the prediction of on-site dump truck tyre life for the studied mine.

Mar 11, 2024

By R. Mier

The metals and minerals mining industry has evolved dramatically from the earliest objects ever made out of native copper circa 9,000 BC to the modern developments we see today. To better appreciate past developments and to get a sense of where the industry is heading, a brief overview of mayor industry highlights over the last 100 years will be presented, followed by a discussion on potential global scenarios and by a review on mayor industry trends.

Feb 27, 2013

By Yves St-Amour, Vince Luongo

This paper will discuss one of the largest construction projects the City of Portland has undertaken. This phase of the Willamette River Combined Sewer Overflow (CSO)project consists of approximately 18,500 ft of tunnel in soft ground, requiring the construction of six deep shafts and jet grout ground improvement. The purpose of the project is to reduce volume of combined sewerage overflows from the drainage areas on the west side of the Willamette River. Bencor-Petrifond-Pacchiosi Joint Venture was awarded a contract to design and construct six deep circular shafts, jet grout ground improvement for three bridges and jet grout ground improvement break-in/outs for some shafts. Of the six shafts the Pumping Station Shaft was the deepest and largest, requiring a permanent ground support system with a deep jet grout ground water cut-off to 335-ft deep. The joint venture used state of the art methods and equipment to achieve its objectives and build the structures through some very difficult alluvial soils to great depths next to the Willamette River. The paper will provide a general discussion of the shaft construction and jet grout ground improvement installed for this phase of the project. It will also discuss some of the technical challenges encountered while effectively managing risk and costs, resulting in a successful project completed in a timely manner.

Jan 1, 2005

In 2002 the authors updated the MFire model developed by the US Bureau of Mines. MineFire, developed by Mine Ventilation Services, Inc. (MVS), uses the MFire model to perform mine fire simulations on typical mine ventilation networks. The MineFire program is capable of producing visual schematics and other analysis tools for input and output of the MFire model. The MFire model, however, was limited to 500 branches and 10 fans. This paper discusses the newly modified MFire model that is now capable of modeling over 5000 branches and over 400 fans among other expansions and improvements. Given the long history and proven track record of MFire, the expansion did not modify the core calculation methods or results. This paper focuses on a general discussion of the MFire program and issues encountered in expansion of the algorithm. An example large network with simulation results is discussed.

Jan 1, 2011

By A. Korchevisky

Environmental self-monitoring is one of the advanced approaches for industrial sustainability programs. Organization for Economy Cooperation and Development (OECD) defines self-monitoring as ?the system of organizational and technical measures put in place and financed by [the] regulated subject? in order to ensure their compliance with regulatory requirements?1. Self-monitoring is beneficial for industrial operators, communities, and governments. Industrial companies use self-monitoring as a central element of their compliance management that allows them to fulfill their duties, obligations, and to avoid citations. When industries control their emissions and ensure workers are not exposed above the regulated limits, communities are better. It is impossible for an EPA, OSHA, or MSHA inspectors to be close to every emission source or workplace full-time. It is much more effective for industries to self-monitor, under due supervision. Occupational conditions are a very important part of industry and health and safety self-monitoring should be highly prioritized. In this paper we will research the regulatory basis and best practice of occupational self-monitoring. We will show that not only is self-monitoring a vital element of an occupational health & safety management system, but that you need a management system for affective monitoring.

Jan 1, 2012

By Harry E. Holzschuh

The two Agrico Chemical Company self unloading Phosphate Rock barges put into service in 1976 operate at over their design carrying capacity. Each barge now carries 26,000 short ton instead of the planned 25,000 short ton at 32 foot of draft. They are in service between Agrico's Tampa, Florida Terminal and the Donaldsonville, Louisiana Fertilizer Complex, moving a total of 2,500,000 short tons each year. This was the first use of the Parascrew design for a marine application. The barges, with their 3,000 STPH unloading and matching loading rate is the vital link in this total transportation and handling system. Rock is moved from the Pierce, Florida Mines through the Tampa Big Bend Terminal, across the Gulf of Mexico, and up the Mississippi to the Agrico Faustina Phosphoric Acid Plant 30 miles below Bacon Rouge, Louisiana. The trip from the terminal to the plant is 600 miles and the turnaround time is just about six days. Seven years operating experience has proved that the system works. Fittingly, the two barges are named the "Faustina" and the "Pierce". They have a beam of 85-feet and are 495 feet long. folded depth is 43 feet, with a ballasted light draft of 19 feet and a typical loaded draft of 32 feet. There are four separated holds with the machinery room located forward of 101 hold. Each hold is 51 feet wide at the coamings with an 18 foot straight section on the side, and a 24 foot long, 600 slope sheet for a 23 foot clear reclaim width at the bottom. The Parascrew in each of the holds is 37 feet long between the bearings and is supported on a 14 inch diameter hollow shaft. The screw pitch varies and the diameter of the flights step up from l'-9" diameter to 2'-6" diameter on the discharge end. By sloping the centerline, a minimum four inch bottom clearance is maintained across the hold. Some bending of the tube does take place.

Jan 1, 1983

By M. M. Poulton

Universities are not immune from the large number of retirements facing the mining industry. Department heads anticipate that we will need to replace all of the senior mining engineering faculty in the U.S. by 2020. Long term studies of Ph.D. completion times and success rates indicate that in Engineering disciplines in the U.S., the ten year completion rate is 65% at best and the four year completion rate is less than 8%. We do not have accurate data on completion rates and times for mining or metallurgical engineering Ph.D. students in the U.S. but students self-report their expected completion times are around 4 years. National data on doctoral students indicate that younger, full time students with sufficient financial support have a higher probability of success in completing their degrees in a timely manner. Students in Eastern U.S. mining engineering programs are on average 32 years old, 85% are full time, and the gap between support and cost of attendance is $5,000 per year. Students in Western U.S. programs are on average 38 years old, 78% are full time, and the financial gap is $8,483. Further, it appears that domestic graduate students are not very geographically mobile. The current demand for new faculty is higher in Western programs but the longer term retirements are higher in Eastern programs. While all Ph.D. students who responded to the 2010 survey indicated an interest in a faculty position at some point in their careers, very few were applying for the open positions. Over the past 35 years for which data could be obtained, the maximum number of Ph.D. students enrolled in mining engineering in the U.S. is 115 with a maximum of 27 degrees granted in one year. On average 89 students are enrolled in doctoral programs in mining engineering in the U.S. with average degree production of 15 Ph.D.s per year.

Jan 1, 2012

By Viktor Lishchuk, Olof Martinsson, Tobias E. Bauer, Elena Haller

Freely accessible and non-confidential real-life geological data sets from mineral deposits are desirable for the wide range of applications in research and education. However, publicly available statistical data are limited in their number and quality—they contain reduced information about geological, geophysical, geotechnical, chemical, mineralogical, and other relevant properties of deposits. This makes such data insufficient for scientific purposes. However, the amount of geological knowledge obtained for a variety of deposits in the past allows the construction of an idealized synthetic ore body model using analytical approach. Such a model could be used for education purposes and testing basic scientific theories, e.g., visualization of deposit structure; teaching sampling strategies; testing new algorithms for mine planning; or comparing geostatistical modeling methods. This paper presents an analytical approach to simulate volcanic massive sulfide (VMS) deposits and shows how synthetic deposit model can be constructed and further used for studying sampling with drilling and simulating folding and faulting.

Jan 14, 2021

By R. L. Andrew

The southwest Pacific has produced at least four of the world’s premier porphyry copper-gold deposits, and the current level of exploration is likely to produce even more. An appreciable amount of gold is being produced with this copper, with obvious economic advantages. Gold content, in addition to their large size, makes the southwest Pacific’s porphyrycopper-gold deposits very attractive exploration targets. The recognition of telescoping and overprinting of porphyry systems has produced a greater awareness of the likely surface expressions, in particular the significance of advanced argillic lithocaps in porphyry exploration. The recognition of the spatial and genetic association of porphyry copper and epithermal gold systems (Sillitoe, 1972), as in other parts of the world, has had important implications for exploration in the Asia Pacific region.

Jan 1, 1995

St. Peter sandstone is very different from the minerals and rocks that have been studied extensively in mining. On the one hand, it is brittle as characterized by an unusually high friction angle and steeply curved failure envelopes. On the other hand, it is friable, possessing extremely low, and in most cases zero cohesion. The scarcity of the ground control techniques for this particular mining environment has created many difficulties for the mine operators. In order to resolve these problems, the geotechnical properties of the St. Peter sandstones were investigated through a comprehensive research program, which included uniaxial test, triaxial test, porosity test, thin section, X-ray diffraction (XRD), and scanning electron microscope (SEM). The specimens used for the uniaxial and triaxial tests were specially prepared because of the highly friable nature of the St. Peter sandstone. Thin section, XRD and SEM were utilized to examine the effect of the microstructure of the St. Peter sandstones on its strength characteristics.

Feb 27, 2013

By R. Fuenzalida

Since 2007, a number of Multivariable Predictive Control (MPC) Applications have been implemented on SAG mills, among others, within the Kairos Mining Concentrator Automation Program using ?Profit Controller?? and other tools comprising the ?Profit Suite??. Along this journey, several interesting and challenging issues related to SAG mill operation and control have been faced, which are relevant to be shared with the Mineral Processing community. These advanced control applications have an operational objective whose goal is to increase marginal profit on the concentrator, together with increasing mill stability. In regard to this objective, the issues to be presented and described are in direct relationship with ?Profit Controller? features and the SAG role; they are also stated and linked to get the most of the mill. Some conclusions and findings are also presented, leading to recommended practices on how to use the controller. These findings have also lead us to decide further actions to be taken on new applications to deploy and also on devising and implementing some complementary components to increase robustness of the overall automation solution, as well as reducing the need for operator intervention.

Jan 1, 2012

By John L. Bolles

The Phelps Dodge Corporation's Morenci Concentrator includes facilities for coarse crushing, fine crushing, grinding, flotation, tailing, disposal, concentrate filtering, and drying. The Morenci Concentrator daily throughput is in excess of 60, 000 tons. The ore milled is mainly a medium-hard monzonite porphyry in which the principal sulfide minerals are chalcocite and pyrite. The ore is transported by rail from the Open Pit Mine to the primary crushing plant located at the concentrator site. Ore is side-dumped from 80¬ton railroad cars into a sixty-inch gyratory crusher. The ore is then conveyed to a. 12, 000 ton coarse ore storage bin. Fine crushing is accomplished by four parallel lines of conventionally stacked crushers in open circuit. Each unit consists of one seven-foot standard cone followed by two seven-foot shortheads. Ti% product of the fine crushing plant is distributed by two tripper cars across a fine ore storage bin. The crushed ore is then fed by variable speed belt feeders into thirty parallel, single stage, closed circuit grinding units. Each of the 30 grinding units consists of one 6' x 23' conditioning drum, one 10' x 10' ha l mill and two 54" duplex spiral classifiers as principal equipment. The dry ore is fed into the conditioning drum with water to dilute the ore to a slurry of approximately 78% solids by weight. An aqueous solution of ammonium sulfide is also added to the conditioning drum. The ammonium sulfide primarily acts as a sulfidizing agent. The ore slurry containing the naturally occurring sulfide copper minerals and the sulfidized copper minerals discharges into the feed scoop box of the ball mill, where milk of lime, collector and-.dilution water are added. The ball mill product slurry is gravity fed: to the classifier pool where water is added to obtain the desired classifier overflow product

Jan 1, 1977

By S. Norman Kesten

The Galena mine is located astride the Polaris fault in the Coeur d'Alene district of northern Idaho. The surface installations are about a mile up Lake Gulch, the mouth of which is about 2.4 km (1 112 miles) west of the old town of Wallace. The mine had its beginnings when the first claims were located in the early boom days of the district in the 1880s and when the first underground ore bodies were opened up in 1917. During the ensuing 14 years, ore was mined from which were recovered 5.4 Mkg (12 million lb) of lead and almost 14.2 Mg (112 million oz) of silver. Workings consisted principally of a vertical shaft from surface to the 800 level and an offset underground shaft to the 1600 level, together with extensive lateral openings. High-grade silver-copper ore was discovered near the Silver Standard fault in the Sunshine mine, a few miles to the west, on the 1700 level in 1930. By 1937, the Sunshine and adjacent mines were producing silver-copper ore on a regular basis. In 1943 additional ore of a similar type was found along the Chester fault, to the east of the principal Sunshine workings. The interest of American Smelting and Refining Co. (renamed ASARCO in 1975) was aroused and the company's geologists determined that the Galena mine, idle since 1931, provided a geological environment in which similar ore might be found. After negotiations were initiated with the owners of the property, Callahan Zinc-Lead Co., the property in question was deeded to Callahan's wholly owned subsidiary, Vulcan Silver-Lead.

Jan 1, 1990

By Justin Reed, Sara Bewley, Dwight M. Kinnes, Maryam Sadeghi, Ed Hart

This study compares wet gravity and dry magnetic separation for preconcentrating an allanite-rich rare earth ore from the Halleck Creek deposit. Material in the –300/+86 μm size range was treated to define a flowsheet that maximizes total rare earth oxide (TREO) recovery. The ore is dominated by feldspar and quartz, with hastingsite, an iron-bearing aluminosilicate. Because hastingsite’s density and magnetic response closely match allanite, it is difficult to reject using conventional methods. Two separation approaches were evaluated: MG12 spirals for gravity concentration and an Induced Roll Magnetic Separator (IRMS) for dry magnetic upgrading. MG12 spirals performed well in the rougher stage but provided limited gains when used as cleaners. When IRMS was applied as the cleaner stage, TREO grade and recovery improved substantially, showing that a dry magnetic cleaner circuit can effectively replace the wet gravity cleaner step. MG12 spirals remain suitable for highcapacity rougher duty, but dry magnetic separation delivers higher selectivity, simpler operation, and eliminates water use—offering a more efficient and sustainable preconcentration route in water-constrained environments.

Feb 22, 2026

By Yehia M. Youssef, Nourhan Moukhtar, M. H. Abdel-Aziz, Ibrahim Hassan

Copper was recovered from copper sulfate solution in a batch-recycled galvanic reactor operated under forced convection with the generation of electrical energy during the cementation process. The divided galvanic cell consisted of parallel copper and zinc plates. The mass transfer rate and the amount of electrical energy generated were found to be directly proportional to the solution flow rate and the initial concentration of metallic ions and inversely proportional to the distance between electrodes. The experimental results were expressed in terms of a dimensionless correlation including all parameters. The wastewater treatment presented herein cell can be utilized to recover many soluble heavy metal ions from solution with high efficiency.

Oct 2, 2020

By John Parianos

"Seafloor mining provides significant potential economic benefits for many Pacific nations that may be "land poor" but "coastline rich," meaning they have the potential to utilize and profit from the mineral wealth within their Exclusive Economic Zones that extend 200 nautical miles (360 km) out from their coastlines. The Independent State of Papua New Guinea (the State) recognizes this tremendous opportunity and is taking a leadership role in this emerging industry by becoming a 15% partner in Solwara 1 (with an option to increase their investment to 30%).The Solwara 1 Project has been gaining momentum since Nautilus Minerals and the State signed an Agreement on April 24. This new agreement with the State in which they have staked a minimum 15% interest as a meaningful partner, underscores the State’s continued and widespread support for the Project. Signing of this Agreement was a historical occasion and a milestone achievement for Nautilus Minerals and the people of PNG.The machinery being built for the Solwara 1 Project is taking shape. The Seafloor Production Tools are now over 90 percent complete. Assembly of the biggest tool, the Bulk Cutter, was completed in April this year and assembly work on the Collecting Machine and the Auxiliary Cutter commenced in May and June this year respectively. The Riser and Lifting system, which will be used to transfer the mined material from the seafloor to the surface within an enclosed system, is over 50 percent complete. The critical path for the Solwara Project is to secure a suitable vessel arrangement. Nautilus aims to have this completed by the end of this year."

Sep 1, 2014

By F. Khorram

Image processing is a technique that simulates the human vision system. This technique enables applying every statistical or intelligent operation to recognize differences. In this way this new technique is used in quality control systems in most industries. Studying sedimentary rocks is very important from the economic point of view. Some units of sedimentary sequences involve different mineral deposits, hydrocarbon and water resources. Therefore it is important to identify and classify different sedimentary rocks. Descriptive classification of sedimentary rocks is usually based on visual and textural features and chemical composition of a sample. In this paper different samples of a limestone mine in central part of Iran are classified. The samples were collected from different parts of the mine and crushed down in size from 2.58 cm to 3.58 cm. The rock samples were labeled based on percentage of chemical and lithological compositions. Each sample was assigned to one of the distinguished groups. The images of the samples were taken in appropriate environment and processed. A total of 74 features were extracted from the identified rock samples in all images. In order to feature dimensional decrease, principal component analysis method was used. Then Bayesian statistical algorithm was used as a useful tool for classification. Classification Correctness Rate (CCR), calculated for the test data sets are %88, %68, %61 and %72 for the first to fourth class respectively. Therefore it can be inferred that the extracted features of images are appropriate indicators for different samples identification. These precise results besides the advantages of image processing technique, which are increasing speed of operation and decreasing cost, appears to be a desirable success.

Jan 1, 2012

By A. S. Haugh

OHSAS 18001 is a series of international standards for occupational health and safety management. It is comprised of two parts, 18001 and 180029. OHSAS 18001 was formulated by international certifying bodies and is based on BS8800 and was first published in 19996,11. OHSAS 18001 was developed to be compatible with ISO 9001 and ISO 14001 in order to facilitate integration of quality, environment, and occupational health and safety management systems5. It is a voluntary standard and the overall aim of OHSAS 18001 is to enable organizations to control their occupational health and safety (OH&S) risks and improve overall health and safety performance5. OHSAS 18001 is widely accepted in the UK, Europe, and Asia, is gaining momentum in North and South America, and it was used as the basis and conforms to the requirements of ANSI/AIHA Z.10-2005: American National Standard for Occupational Health and Safety Management Systems. It defines a set of requirements for an occupational health and safety management system suitable for any kind and size of organization4. Businesses of all sizes are developing and implementing occupational health and safety management systems (OHSMS) that are in compliance with the OHSAS 18001 standard.

Jan 1, 2012