Search Documents

By S. G. Gendler

The choice of ventilation schemes in the Northern Mujsky railway tunnel and definition of the nec-essary quantities of air ensuring regulated radiation conditions in the tunnel system has been accomplished. The influence of natural draught on the stability of tunnel ventilation has been estimated. The design of a portal venti-lation gate allowing minimal influence from natural factors is described. The dependence of pressure loss in the sliding ventilation gates on their spanning value of the vehicle tunnel section has been determined. The selection of parameters for an atmospheric air heating system in winter has been carried out. The operation regimes of air heaters, dependent on the temperature of atmospheric air, have been established.

Jan 1, 2009

By J. Evans

Including: Tailings thickeners, CCD?s, paste thickeners, HI-rate thickeners, lamella thickeners, high compression thickeners, clarifiers etc. Flocculant dosing control for mining thickeners and clarifiers is influenced by a number of process factors. 1. Flow rate into the thickener or clarifier a) As the flow rate increases into the thickener or clarifier ?retention time? decreases which causes a greater affect hydraulically on the settling solids. So as the flow rate increases it will generally mean an increase in flocculant dosing rate. b) As the flow rate decreases into the thickener or clarifier the retention time increases which reduces the hydraulic affect on settling, improving settling rates. This will generally mean that as the flow rate decreases, we will decrease the flocculant dose rate.

Jan 1, 2011

By H. K. Lin, J. L. Oleson

The purpose of this study is to develop a mathematical model to describe the oxidation of cyanide with SO2as proposed in the Inco process. This research employed a direct method for measuring the change in cyanide concentration with respect to time as effected by varying concentrations of SO2, copper and pH. Developing this model may be applicable in determining optimum conditions in a process well known and used in the mining industry. It was determined that the reaction is first-order with respect to cyanide, SO2and [Cu+2].The reaction order is 0.15, or zeroth order with respect to [H+] at pH range from 8.0 to 9.5.The activation energy, Ea, is 21.6 kJ/mol. The overall rate equation, as determined through this study is: [ ]

Jan 1, 2004

By Walid M. Abdellah, Soliman Abu Elatta A. Mahmoud, Hanaa A. Abu Khoziem

The high-grade Th-U-Y zone is one of the numerous mineralized zones found in the El Garra El Hamra hydrothermally altered syenites in southwestern Egypt. It is characterized by the thorium minerals thorite and thorogummite, which are closely associated with xenotime-(Y). This zone of mineralization is localized in the eastern part of the El Garra El Hamra hydrothermally altered syenites. This zone does not relate to the first phase of syenites that appeared on the surface but is linked to the other, hidden phase of the syenitic body. Additionally, the fluids responsible for the mineralization of this zone belong to the late-stage hydrothermal event as well as the fault action due to the fact that it had continued reactivations for a long period of time. The studied mineralized zone also contains ceriopyrochlore-(Ce),(Ce,Ca,)2 (Nb,Ta)2O6 (OH), fluorite (CaF2) and barite (BaSO4), which are found in considerable amounts, whereas apatite (Ca5(PO4)3F) and chromite (FeCr2O4) are rarely found together with Fe-oxi-hydroxides (hematite and goethite) with a minor amount of jarosite (KFe33+(OH)6(SO4)2). Finally, the main constituent mineral in the zone is the pseudomorph perthite in addition to quartz, which is found as deformed crystals. A technological sample was collected from this zone and was found to assay 4.62 weight percent thorium (Th), 0.37 weight percent uranium (U) and 3.12 weight percent rare earth elements (REEs). From the chemical and mineralogical composition of the studied technological sample, the leachabilities of Th, U and REEs were investigated using sulfuric acid (H2SO4) agitation leaching and pug leaching methods. The latter was found to be preferred under the conditions of 0.54 ton H2SO4 per ton of altered syenite at 110 °C for two hours.

By D. Potter

Freeport Exploration initiated regional reconnaissance exploration programs in Irian Jaya, the easternmost province of the Republic of Indonesia in 1990 (see figure 1). Irian Jaya occupies the western half of the island of New Guinea. Freeport was awarded an initial contract of work which totaled 2.6 million hectares (6.4 million acres) and was subsequently awarded additional?concessions which added 1 million hectares (2.5 million acres). The concessions require work commitments and periodic relinquishments. Due to these relinquishments Freeport?s current land position totals l. 9 million hectares (4.7 million acres).

Jan 1, 1998

By T. McKeon, G. Luttrell

Spiral separators are commonly used to upgrade sand-sized particles in both the coal and mineral processing industries. Many plants utilize multiple stages of cleaning and/or scavenging spirals to improve recovery and/or final product grade. Field studies suggest, however, that the layout of industrial spiral circuits is often less than optimal. This oversight can usually be attributed to a failure by plant designers to consider fundamental process engineering rules that govern the layout of complex separation circuits. This article reviews some of these important rules as specifically applied to multistage spiral circuit design. Two industrial case studies, one involving the upgrading of heavy mineral sands and a second involving the cleaning of fine coal, are presented to illustrate the impact of good design protocols on spiral circuit performance.

Jan 1, 2007

By Daniel Connor, O&apos

The Cal-Sag Relief Sewer is a 2.6 m (8 ft 6 in.) diameter 9.1 km (5.7 mile) rock tunnel bored in dolomite for the Metropolitan Sanitary District of Greater Chicago. Included in the project are 18 shafts varying in depth free 70 m (230 ft) to 41 m (135 ft). This paper discusses how Healy/Vanessa reduced costs by eliminating conventional hand excavation by hoisting muck from a high production Robbins TBM (Tunnel Boring Machine) through small diameter drilled shafts and using a trailing rail-utility backup system.

Jan 1, 1985

By Satoshi Honda, Mitsuru Shimizu, Tatsuji Nagao, Motoaki Kurisu, Hirokazu Izumi, Toshinori Takahashi, Hiroyuki Itoi

"1. INTRODUCTION Grade separation of roads and railway tracks is an effective method for solving traffic-related issues in cities. However, in urban areas where the existing traffic infrastructure is already overcrowded, construction of new roads often faces problems especially in the proximity of existing structures. This paper summarizes the construction plan and results of new road tunnel construction in the proximity of the piers of elevated tracks on the Tokaido Shinkansen railway.2. SUMMARY OF CONSTRUCTION AND ISSUES Auxiliary Route No. 26 as specified in the Tokyo urban plan is a project by the Tokyo Metropolitan Government, covering the construction of a new road with a total length of 22.3 km currently on the way to completion. In Shinagawa Ward, Tokyo, Auxiliary Route No. 26 is designed to cross the railway tracks of the Yokosuka Line and the Tokaido Shinkansen Line, so for this project, the East Japan Railway Company (JR East) was commissioned to design and build a road crossing under the railway tracks (Sumiyoshi Underpass). Figures 1 through 3 show a sketch of the Sumiyoshi Underpass. The Sumiyoshi Underpass was planned as a two-lane tunnel for vehicles, which was to cross under the railway tracks of the Yokosuka Line and the Tokaido Shinkansen Line at an angle of 70 degrees. The structure concerned is a single-story single-span box culvert structure with the following dimensions: 11.5 m wide, 7.7 m high and 31.6 m long. The Tokaido Shinkansen Line tracks were constructed on a girder-type elevated bridge built in the 1960s, and the foundation piles of the piers (P7 and P8) in the proximity of this crossing box culvert of RC structure were constructed using an earth drill method. The crossing structure for this project is located extremely close to the piers of the Tokaido Shinkansen railway tracks, with a minimal separation of 0.4 m, and the most significant issue of this project was construction in a manner that would not obstruct the normal operations of the Tokaido Shinkansen (Figure 4). Initially, we considered installing a temporary earth retaining structure in the proximity of the piers, cutting the ground and building an RC box, but concluded that it would be very difficult to apply this method because of probable excessive displacements in the Shinkansen railway piers. That is why we decided on the use of a non-open cut method in order to minimize the impact on the piers."

Jan 1, 2016

By Will Foreman, Douglas D. McLearie, Edwin K. H. Tong, William H. Hansmire

Hong Kong’s Strategic Sewage Disposal Scheme (SSDS) Stage I involves the provision of a system of deep tunnels for transporting to a central treatment works wastewater collected from a number of catchments around Victoria Harbour. For the SSDS Stage I works, about 24 km of tunnels have been excavated in hard rock at depths ranging from about 80 to 150 m below Victoria Harbour and the surrounding heavily developed areas of Kowloon and Hong Kong. Five tunnel boring machines(TBMs) with diameters ranging from 3.2 m to 4.3 m were used to excavate the tunnels. Tunnel excavation has been completed and tunnel linings are in progress. Major tunnelling issues such as ground stabilisation and water control encountered in the project are summarised. An overview of one of the possible future tunnel systems that might be adopted in subsequent stages of SSDS is also presented.

Jan 1, 2001

By John E. Caffrey

Mr. William. J. Montgomery in his book "Theory and Practice on Mine Ventilation stated "Ventilation is vitally important to underground mining for three reasons: First, it sweeps all workings with a plentiful supply of air and drives to the outside the smoke, gases, and contaminated air which would be injurious to the miners; second, it dilutes and renders harmless the explosive gases emitted from the strata, thus eliminating the dangerous conditions caused by the accumulation of these gases; third, it keeps the mine air as nearly as possible of the same composition as the outside air, thus giving to the miner the healthiest possible condition in which to work...." Specific methods to achieve the above basic reasons for mine ventilation were established in the Federal Coal Mine Health and Safety Act of 1969. Sections 303(y)(1); (y)(2), and Section 317(f)(4) of the Act, which can be broadly described as entrapment features, are controversial and debatable in the minds of many mining engineers in their intent and method for affecting, 303(y)(1) in certain cases prohibits the use of belt haulage entries as an intake for face ventilation, This is to say that air traveling in a belt entry will be placed into the returns and not used for face ventilation, 303(y)(2) limits the velocity of the air on trolley haulage entries. The regulations, as published in the Federal Register, have set this limit at 250 feet per minute unless a higher velocity is approved by the District Manager.

Jan 1, 1972

By K. Oraee

Rate of penetration of Tunnel Boring Machines (TBM) has a significant role in the planning, measurement of productivity and performance of any tunneling project. In this paper, the application of Adaptive Neuro Fuzzy Inference System (ANFIS) in prediction of TBM penetration rate is evaluated. For this purpose, a database including Rock Quality Designation (RQD), Uni-axial Compressive Strength (UCS) of the rock, the Distance between Planes of Weakness (DPW) in the rock mass, and empirical data regarding rate of penetration of TBM from several tunneling projects are collected. The Rate of Penetration is then estimated by using ANFIS. These results are then compared with measured TBM penetration rates (actual data). It is concluded that ANFIS can be applied successfully for such purpose and result in high accuracy for prediction for the rate of penetration of TBM. The method provided in this paper can assist the mining engineer to estimate the performance of tunneling accurately.

Jan 1, 2012

By A. Chieregati

"A heterogeneity study was conducted at Erdenet Copper Mine in Erdenet, Mongolia, to determine the fundamental sampling error associated with blasthole sampling. Using a custom-designed radial sector sampler , six large blasthole samples were collected to perform the test developed by Pierre Gy to estimate the constitutional heterogeneity factor for several types of ore. The study investigated the entire sampling protocol, from mine site to analytical laboratory, and quantified the contributions to total fundamental sampling error (FSE) of the various stages of sampling and sample preparation. The total relative standard deviation (RSD) of sampling error was determined to be ±32 percent and ±49 percent for copper and molybdenum, respectively. A classical statistical analysis conducted on the data confirmed the level of RSD native to the mine. About 95 percent of the sampling error was produced from one step in the sampling protocol, that of reducing the 1-kg (2.2-lb) sample to a 50-g (0.1-lb) sample for chemical analysis. To minimize the FSE, the use of a slightly different protocol is recommended. The 1-kg sample (2.2-lb) should first be crushed to a 0.2 cm (0.08 in.) particle size. A 250-g (0.5-lb) split should then be taken and finely ground, from which a 50-g (0.1-lb) split should then be taken. These simple steps will reduce the FSE to ±7.9 percent and ±17 percent for copper and molybdenum, respectively. The modified sampling protocol effectively reduces to zero the probability of misclassification of low-grade ore. IntroductionThe Erdenet copper-molybdenumopenpit mine is located in Erdenet in Orkhon province, Mongolia. The Erdenetiin-Ovoo copper-molybdenum deposit is 1.5 to 3 km (0.9 to 1.8 miles) wide and about 25 km (16 miles) long (Erdenet Mining Corp., 2016). Chalcopyrite, bornite covellite and chalcocite are among the major minerals found in the deposit. The mine processes approximately 26 Mt/a (29 million stpy) of ore."

Jan 11, 2017

By M. Ge

Signal processing is a major challenge for In-Seam Seismic (ISS) technique. Fourier Transform is an important tool for signal processing such as frequency analysis. However, for ISS signal, localized information, especially time-frequency localization is even more important. Wavelet Transform (WT) provides another approach to study the signal as a function of frequency and time. The objective of this paper is to demonstrate the application and advantages of WT to seismic signal analysis. Both transmission and reflection signals from coal mine void detection experiments are analyzed. The results illustrate that WT appears to be a powerful and convenient method for the in-seam seismic signal processing.

Jan 1, 2007

By David G. Adam

Introduction Syncrude Canada Ltd. is the operating company for a consortium of industry and government participants that produce synthetic crude oil from their leases in the Athabasca Oil Sands. Production from the $2.3 billion (1978) integrated mining, extraction, and bitumen upgrading and utility complex started in September 1978. Production is currently about 6.4 Mm3/a (40 million bbl per year) of high quality synthetic crude oil. This is done by upgrading the extracted bitumen from the oil sands mined. Plans are to increase the production to 8 Mm3/a (50 million bbl pier year) by 1989. At that time, the mining operation will be required to deliver 100 Mt/a (110 million stpy) of oil sand (ore) to the extraction plants, and handle quantities of waste ranging from 50 to 75 Mt/a (55 to 83 million stpy). The Syncrude plant is located at Mildred Lake, 40 km (25 miles) north of Fort McMurray and 480 km (300 miles) north of Edmonton, Alberta. Climate, particularly winter, is therefore a major factor affecting the design and operation of all the Syncrude production facilities. Bitumen production, consisting of overburden removal, oil/sand mining, bitumen extraction, and tailings disposal, account for about half the total SCO production costs. Considerable research and development, therefore, continues to be applied to improve both material handling and bitumen recovery methods. Potential applications for feeder breakers were identified in the material handling aspects of both overburden and oil sand mining to reduce cost and to attain planned production increments. Overburden removal Overburden materials on the leases comprise thin Pleistocene sands, gravel and fill, and sands, silts and clays of the thicker Clearwater Formation with the silt to clay components predominating. The latter contains multiple leases of hard siltstone with unconfined compressive strengths up to 148 MPa and thicknesses up 0.1 to 0.9 m (1 to 3ft). Characteristics of the overburden as well as the climatic environment and scale of operation present unique problems for the efficient removal of the material. In a bucketwheel/conveyor system, the weak silty clay formations require relatively flat working slopes for safe operation, while the siltstone lenses and frozen overburden require blasting or selective removal by other equipment. These factors, combined with the normal bucketwheel/conveyor design parameters, lead to high capital investment and relatively inefficient use of that capital. Hydraulic mining alternatives, including dredging, are constrained by severe clay settling problems in the waste disposal

Jan 6, 1986

By A. Supomo, A. Partanen, M. Mular

Although many SAG operators may agree that on-line measurement of SAG feed-size is an attractive notion, applying this information in a control strategy that recovers the investment, engineering time, and maintenance is not necessarily straightforward. The P. T. Freeport Split-Online system was justified based on the assumption that SAG feed-size could be used in a feed-forward control strategy either at the regulatory or expert system control level. Something like “as the feed size changes adjust the throughput to avoid under or overloading the mill” was envisioned. However, following installation and calibration, Cluster Analysis showed that such an approach would not be successful. However, the sensor has been successfully integrated into Freeport’s grinding control strategy other ways. It provides an input to the Kalman filter parameter estimator used in a model-based control strategy that optimizes throughput and grind. The Split sensor also provides a characteristic feed size parameter for use in an on-line work index estimator. This paper describes the calibration and installation of the Split SAG feed-size analyzer, and reviews the evolution of its use in the Freeport C3 grinding circuit control strategy.

Jan 1, 2001

By G. A. Gamble

Fans used to ventilate subway, passenger rail and vehicular tunnels are similar to the fans used to ventilate underground mines. However, tunnel ventilation fan systems are typically designed to meet NFPA 130 or 502 standards, while mine ventilation fan systems must comply with the appropriate federal mine safety regulations. As a result, fan operation requirements and performance criteria, as well as typical fan and duct configurations differ significantly for tunnel and mine ventilation applications. Variations in environmental conditions in tunnels as compared to mines also result in differences in fan performance and material specifications. The need to enclose tunnel fans within building structures creates space restrictions impacting fan size selection that are not commonly encountered in mine fan installations, resulting in different approaches to selecting fans for the two types of tunnels. This paper discusses the various similarities and differences in design considerations for tunnel and mine ventilation fans.

Jan 1, 2009

By Daniel H. Isreal

Because the federal government owns and controls nearly 80% of the most valuable oil shale reserves in the West, it is inevitable that federal leasing and siting will play a prominent role in development of an oil shale industry during the 1980s. Also, because of recent enactment of the Synthetic Fuels Corp. authorizing up to $88 billion in loan and price guarantees-federal financing will provide the critical incentive to permit private investment in a still infant industry.

Jan 1, 1981

By Don C. White

The Vulture mine near Wickenburg, Arizona was a major gold producer from 1863 to 1942, having yielded about 11t(12.1 st) Au and 8t (8.8st) Ag. Gold occurs as coarse native metal and electrum in quartz veins and also finely dis¬seminated within a quartz monzonite sill and its silicified wall rock. The sill is semi-conformable within a Proterozoic volcaniclastic-dominated sequence, all dipping north about 35°. Early mining focused on the vein-hosted gold, particularly in the immediate hanging wall and footwall of the sill. Later efforts included some open-pit mining of the outcropping sill and adjacent altered and mineralized rock. Two sets of post-mineral faults have complicated the orebody geometry. The sill is a 350 m (1148 ft) long apophysis from a quartz mozonite stock to the west of the mine area. The stock has been dated at 85 my and contains abundant lesser gold occurrences in its core and about its margins. The Proterozoic rocks are notably lean in precious metals except where altered in proximity to the Creataceous stock and sill. Circumstances dictate an interpretation of epigenetic mineralization related to the Laramide intrusion.

Jan 1, 1990

By J. Kallioinen

The development of mechanical flotation cells has resulted in larger and better cells. This has led to flotation banks with only a few units, even in large-scale operations. This equipment development makes the old operational considerations ineffective. The flotation cell must be considered as a single reactor unit capable of handling specific tasks and getting excellent metallurgical performance. The result of the unit reactor concept development was the new large TankCell that comes in sizes up to 113 m3 (4,000 cu ft). The TankCell construction includes new modified rotor-stator designs, new tank geometries and a froth-handling capability independent from subprocesses taking place in the pulp (i.e., air addition). The conventional idea of a single flotation cell type for fine, intermediate and coarse materials does not give optimal results. Optimal flotation of coarse and fine particles needs different mechanism designs, impeller tip speeds and different froth control objectives.

Jan 1, 1995

By Michelle L. Ramos

INTRODUCTION The Ballard Siphon was built in 1935 and consists of two 91.4 cm (36-inch) diameter wood-stave pipes. These pipes convey sewer flowsunder the Ship Canal from northwest Seattle and the Ballard Regulator to the North Interceptor and the West Point Treatment plant. The siphons were constructed using open cut construction, are now buried in the sediment on the floor of the canal, and have severely limited ability to be dewatered, inspected, or cleaned. The existing siphon is 394.7 m (1,295 feet) long from the junction structure on the southern shoreline to the regulator structure on the north. The location of the Ballard Siphon is shown in Figures 1 and 2. The area around the Ballard Siphon has become more populated and developed since the siphon was built. Additionally, the Ballard Siphon is subject to high flows that are greater than the capacity of the pipelines. This has resulted in predict-able Combined Sewer Overflows(CSO?s) whenever a large, long duration rain event occurs. The aged pipeline of uncertain viability has become a critical piece of the sewer system infrastructure. Because of the age of the pipelines and their importance, a sonar survey was completed on both barrels of the Ballard Siphon in December of 2005. The sonar images appeared to indicate crown intrusion of the wood-stave pipes, which suggested that the pipes were in imminent danger of collapse. As a result, an Emergency Declaration was executed by King County and the Ballard Siphon Replacement Project was initiated. Staheli Trenchless Consultants was retained to perform feasibility studies to deter-mine the viability of using microtunneling and horizontal directional drilling (HDD) for replacement of the Ballard Siphon. For the evaluations, the preferred site location was determined to be at or near the site of the existing Ballard Siphon in order to minimize the ancillary sewer work which would accompany moving to a new site. To meet flow demands and hydraulic requirements, the replacement siphon needed a mini-mum equivalent diameter of 182.9 cm (72 inches). This could be accomplished with a number of different siphon diameters and configurations including, but not limited to, three 106.7 cm (42-inch) diameter pipelines, two 152.4 cm (60-inch) pipelines, or two 91.44 cm (36-inch) pipelines and a 121.9 cm (48-inch) pipeline.