Search Documents

By T. Tempel

In 1994 Newmont Gold Company commissioned a 2.5 Mt/a refractory gold ore roasting plant near Carlin Nevada. Many unique characteristics of this facility required use of specialized materials of construction in the areas of dry grinding, roasting, gas cleaning, and sulfuric acid production. Process conditions and design criteria that necessitated the use of special materials include; siliceous and abrasive ore, low roasting temperatures, gas streams with high concentrations of oxygen and sulfur, and stringent environmental regulations. Materials selected for use were ceramics, corrosion resistant steels, high temperature steels, and high temperature polymers, lead, polypropylene and low flammability PVC.

Jan 1, 1997

By D. Kimball, P. Chambers

"BACKGROUND In the event of an explosion or fire in an underground mine, workers can be exposed to a deficiency of oxygen, an excess of carbon monoxide, or both. These threats can occur as separate conditions or simultaneously. A lack of oxygen in the breathing air can only be addressed via the use of a self-contained breathing apparatus (SCBA) acting as a source of oxygen. An excess of carbon monoxide can also be addressed via the use of an SCBA, but if the threat occurs in isolation (that is, the atmosphere still contains sufficient oxygen to support life) and the concentration of the threat gas is not extreme (< 2%) then the carbon monoxide threat can also be addressed by the use of a filter self-rescuer (FSR). Used together, the SCBA and FSR offer a far more efficient and universally capable life support system than when used in isolation. However, the SCBA does not take advantage of the fact that the surrounding atmosphere likely contains some level of useable oxygen; i.e., the SCBA always supplies the total required oxygen from its limited supply, resulting in a ceiling on its useful life regardless of the level of oxygen in the surrounding air. To address this technology gap, what is needed is a ""smart"" SCBA that provides filtration and catalytic protection against threat gasses and has an extended duration life-sustaining oxygen inhale stream independent of the threat content and oxygen deficiency of the surrounding atmosphere. DEVELOPMENT Developed under contract with NIOSH the Smart Escape SCBA is comprised of three major components including; 1) oxygen supply, 2) oxygen sensing & dosing electronics and, 3) a CO catalyst and carbon bed broad spectrum FSR. The SCBA is designed as a hybrid system that provides non-toxic breathing air by using an approved Chemical, Biological, Radiological and Nuclear filter self-rescuer and a catalyst to convert high levels of carbon monoxide to harmless carbon dioxide (CBRN FSR/CO). In addition, the Oxygen Sensing & Dosing Electronics (OSDE) package adds sufficient oxygen to make up for deficiencies detected in the ambient air (Figure 1). By making use of the ambient oxygen, less oxygen is required for a one-hour unit life. This means that the Smart Escape SCBA fits in a smaller and lighter package than a similar-duration conventional Self-Contained Self-Rescuers (SCSR). Alternatively, taking advantage of available ambient oxygen could offer a significant increase in working duration in a unit with the same size as current SCSRs. The research performed under this NIOSH contract involved numerous tasks including: (1) definition of performance and system requirements for the Smart Escape SCBA, including keeping environmental stressors within acceptable ranges, providing at least one hour of breathable oxygen supply, and using a mask or hood that allows high-quality voice communication; (2) designing, building, and evaluating prototype units to support extensive bench top testing at Avon Protection and third party labs to demonstrate the device’s capabilities; (3) building sufficient quantity of Smart Escape SCBAs designed to be intrinsically safe (per MSHA criteria); (4) testing and evaluation by the National Personal Protective Technology Laboratory (NPPTL)."

Jan 1, 2015

By D. Kelley

Due to pricing volatility and lack of availability of metals, the use of non-metallic materials of construction in metal extraction and refining processes has increased significantly in recent years Even though costs and availability of metals has improved recently, these factors are not expected to continue into the future as metal supplies once again fall short of global demand. One of the most common non-metallic materials of construction used in metal extraction and refining processes today is Fiberglass- Reinforced Plastic (FRP). These processes often require materials of construction that can resist acids and high concentrations of acid chloride salts. As shown in Table 1, FRP based on epoxy vinyl ester resin has the same chemical resistance to acid and better resistance to acid chloride salts than alloy C-276 and is superior to 2205 stainless steel in both cases.

Jan 1, 2010

By C. G. Roache

Mining legislation in Jamaica dates back to only 1947 when, on August 30 of that year the Minerals (Vesting) Act was promulgated. None of the exploratory and trial-mining projects over the preceding 450 years were regulated or controlled by law. It was the seriousness of the intent of the North American Aluminum Companies to establish a bauxite mining industry in Jamaica which led to the development of the first piece of mineral legislation. It is of note that the incoming mineral industrialist was more anxious than the Government to see that a legislative framework was in place. It was relevant then as it is today for good mining legislation to be in place for the Government to regulate and control the exploration and exploitation of mineral resources. It was also necessary for the industry to know their rights and obligations so that they could plan, explore and exploit with some assurance that their capital was secure. One of the main reasons that the mining of bauxite did not begin in Jamaica until 1952 was that no legislational framework existed prior to 1947. The Jamaican dollar is tied to the US Dollar at a rate of J$35.00 to US$1.

Jan 1, 1998

By X. K. Jiang

Pneumatic, triboelectrostatic processing of physical mixtures containing fine (-200 mesh) particulate may have significant application potential in the mining and energy industries. Such dry processing methods, especially for finely comminuted materials, have not been examined in as much detail as wet processing methods nor have been part of the training or education of mining and process engineers. We have examined fundamental and applied physical and engineering factors controlling triboelectrostatic beneficiation of fine-sized physical mixtures, one of which -combustion fly ash -has size, heterogeneity and mineral concentrations typical of those expected in mined minerals. The applicability of dry processing, however, cannot be readily evaluated because of the unavailability of standard procedures for process assessment.

Jan 1, 1999

By John M. Hird

Texasgu1f&apos;s Lee Creek Mine in Eastern North Carolina is usin8 a combination Dredge-Dragline method for mining deep phosphate ore at a rate of 8.5 million tons per year. The matrix is thick, uniform in grade, and is processed into agricultural products. As in many other good mineral deposits, there are tough obstacles to overcome in recovering the ore. The deposit is in an area with a land surface of about ten feet above sea level, is close to tidewater, is overlain with 90 to 130 feet of unconsolidated overburden, and is underlain by an artesian aquifer with over 140 feet of natural hydrostatic head at the bottom of the bed, The upper 40 feet of overburden will not support stripping equipment and is unstable when cast as spoil. Barriers are emplaced to prevent flooding from hurricane tides. The ground water problems have been successfully controlled by pumping 60 million gallons per day from the aquifer. Only recently have the severe ground problems been overcome by this unusual Dredge-Dragline combination of mining equipment.

Jan 1, 1978

By Giorgio Höfer-Öllinger, Peter Pointner, Manfred Stadlober

"SUMMARY Investigations from tunnel face are part of risk mitigation measures during the excavation works. With the tunnel equipment, percussion drillings of up to 30-40m can be achieved. Core drillings are state of art method for investigation exceeding 50m. At Koralm base tunnel, up to 270m deep percussion drillings were performed with drilling rigs and accompanied by an intensive investigation program. These investigations consisted of monitoring during the drilling, field tests (with packer, using the preventer, borehole imaging) and in laboratory. Percussion drillings are cheaper and save time of interruption of the excavation progress. INTRODUCTION As part of a proper risk management, horizontal advance drillings during excavation of underground works can be seen as state of art and meet wide acceptance. Core drillings, deep and shallow percussion drillings can be differed. The selection of the type of drilling, meanwhile, causes intensive discussions. On the one hand, only a core drilling allows a direct investigation of the rock mass expected during later excavation works. On the other hand core drillings are expensive in both cost and time – if there is no excavation progress during the investigation measures – in construction time. Percussion drillings can be performed as rapid investigation measure with the excavation equipment (“Jumbo”) allowing two dimensional image of the ground around the cross section. There is some limitation concerning a reasonable depth of approximately 30m and a borehole diameter of 76mm. The applications of preventer, packer or borehole imaging are hardly applicable. By use of a drilling rig depths of percussion drillings of several hundred meters can be achieved relative easily and there is less limitation of the borehole diameter. Installation of a preventer is possible, as well as packer tests and borehole measurements (imaging, gyroscope, borehole geophysics). The gap of information between core and percussion drilling cannot be closed completely, but it can be reduced substantially and sufficiently by combination of an intensive program of measurements and analysis accompanying the investigation works."

Jan 1, 2016

"The Industrial Comminution Efficiency (ICE) working group, part of the Global Mining Standards and Guidelines Group (GMSG) has engaged a large number of industry professionals representing mining companies, equipment vendors, consultants and metallurgical laboratories with interests and capabilities in the comminution field. These participants have collaborated to develop three guidelines for the assessment of the efficiency of mineral comminution circuits. Two of these guidelines deal specifically with power based modelling techniques to quantify energy efficiency using widely practiced techniques, those developed by Bond (1961), Rowland and McIvor (2009), and Morrell (2009). The third guideline deals with the sampling and surveying of grinding circuits as is required to provide the necessary information, at appropriate quality, to furnish the efficiency analysis promoted by the first two guidelines. This preprint will focus on the Guideline on Methods to Survey and Sample Grinding Circuits, which is currently in the final stages of peer review and finalization by the GMSG. INTRODUCTION It is important to make a clear distinction on the scope of work of the GMSG guideline for sampling grinding circuits. Many mineral processing practitioners are familiar with the sampling and surveying of comminution circuits, in particular grinding circuits, for performance diagnosis and the identification of optimization potential. These surveys often provide information for population balance modelling of individual comminution and classification unit processes, and as a result require a large amount of information to calibrate and validate the unit models. As a result these surveys are labour intensive, somewhat expensive depending on internal capabilities of the mine site or company, and have a long time span from initial planning to final reporting. They also require a high level of expertise to process the survey data, simulate the circuit and make sensible recommendations on follow up actions. As a result of these factors full grinding circuit surveys are not a common occurrence at a large number of facilities, and several years may pass before follow up surveys are conducted. In the ensuing gap between surveys, the efficiency of the grinding circuit must often be taken on faith, and this is considered an unacceptable lapse in an environment of strained natural resources and low commodity prices. To support the rapid and productive energy efficiency analysis being promoted by the ICE working group, a much simplified survey and analysis process is required. The process reflected in the GMSG guideline is indeed more conducive to frequent analysis, at a skill level that is well within the capabilities of the average plant metallurgist. As a result it becomes feasible to conduct mini-surveys of plant performance, which can be used to quickly and precisely diagnose the high level impact of process changes. It can also be manipulated by experienced practitioner to provide sufficient information for modelling of the circuit to estimate the impact of process changes, supporting an initial rate and rank exercise to focus plant optimization efforts."

Jan 1, 2016

By M. A. Greenwood

The total value of coal, FOB mine, consumed in the United States was $21 billion in 1985. Roughly $6 billion was spent to transport coal from the mine to the consumer by rail. This indicates the impact railroad transportation has on the competitiveness of U.S. coal as an energy resource. Actually, this is just the tip of the iceberg. When you consider the largest U.S. reserve of coal, the Powder River Basin, which is possibly the lowest cost coal in the U.S., or maybe even the world, the transportation cost is the overriding factor in developing competitive pricing. Rail transportation costs from Powder River can be multiples of 2, 3, or even 4 times the cost of coal FOB mine. About sixty percent of all U.S. coal is shipped by rail. In the case of Powder River Basin coal and many other reserves there are no current alternatives to rail. Are there feasible alternatives to rail transport?

Jan 1, 1986

By C. M. Liu

"The Freeport-McMoRan Sierrita Crystal Plant produces Copper (II) Sulfate Pentahydrate (CuSO4·5H2O) through a series of cooling crystallizers. In this process, high supersaturation and unwanted spontaneous nucleation promote fine crystals. Seeding through recycled crystal classification can manipulate the crystal size distribution (CSD) for larger crystals. Proper selection of the crystallizer for seeding can prevent spontaneous nucleation and promote final crystal size. This study shows when seeding temperature is closer to the crystallizer temperature, suspension densities in the crystallizers are promoted and overall CSD shifts to a larger size of crystals. INTRODUCTION Figure 1 shows an overview of the crystallization process. The in-plant feed flow, called Pregnant Mother Liquor (PML), enters the first crystallizer and is subsequently cooled through a series of four crystallizers. Specific temperatures are targeted for each crystallizer to ensure the crystallization process is operating within the metastable zone (MSZ). The discharged flow from crystallizer #5 then enters two cyclones. The overflow from the cyclones contains smaller crystals providing seed crystals for crystallizer #5. The underflow from the cyclones begins the drying process. The overflow from crystallizer #5 enters cyclone #3 for removal of fine crystals and seeding purposes. The underflow from cyclone #3 has the capability to provide seed crystals for crystallizer #1 or crystallizer #2. The overflow leaves the system as Spent Mother Liquor (SML). Undersize crystals dissolve into the PML and return back to crystallizer #1.THEORIES AND METALLURGICAL TESTS Seeding requires an understanding of the crystal size, solution temperature and amount of crystals that enter the crystallizers (1). For the seed crystal size, classified crystal seeds can prevent fine crystals returning back into the system which eventually leads to excessive agglomeration (2). Proper selection of the crystallizer can ensure seeding at an appropriate temperature. Seeding at a temperature much lower or higher than the saturation temperature promotes spontaneous nucleation. Typically, seeding between 4-5°F below the saturation temperature is acceptable (5). A general rule of thumb is to add the seed crystals at the temperature between the solubility curve and the metastable zone. An experiment conducted by Mettler-Toledo AutoChem, Inc. indicates seeding close to the solubility curve rather than the metastable zone promotes a lower supersaturation and nucleation rate but yields a higher growth rate and a greater number of larger crystals (1). The amount of seed crystals can not only change the suspension density but also narrows the width of the MSZ in the crystallizers. An experiment conducted by Jaroslav Nyvlt reports with the crystals absent, the maximum allowable undercooling is 6.3 degrees at a cooling rate, 5°C/hour. With the presence of crystals, it narrows the MSZ width to 2.2 degrees (4). Industrial crystallizers normally operate at suspension densities between 15% and 25% by mass. When suspension densities are lower than 15%, it increases the risk of primary nucleation and the probability of incrustations; on the other hand, if the suspension densities are greater than 25%, it can cause a greater attrition rate and increase the probability of deposits (6). Moreover, operating suspension densities between 15% and 25% are also sufficient to minimize supersaturation rate which promotes crystal growth over nucleation (2, 6)."

Jan 1, 2015

By Horace M. Varner

Under sponsorship of the USBM and later of the DOE, a new type of rotary rock drill has been developed by The Bendix Corporation. Originally developed for the production of holes for the installation of longer than seam height roof bolts, the flexible drill is a useful tool for many drilling applications. This drill allows hands-off or remote production of holes for increased drilling speed and greater operator safety in any strata suitable for rotary drilling. The paper discusses various applications and experience for the flexible drill system in coal mining, metal/nonmetal mining, and for general civil engineering uses. Manual, remote control, and automatic roof bolter modules are also discussed.

Jan 1, 1982

By F. Dingwu

The demand of manufacturing high-purity magnetite concentrate leads to the advent of various magnetic separators. A novel magnetic drum separator has been developed with an optimal permanent magnet system and a complex-forces field is adopted, involving magnetic force, gravitation, fluid resistance, friction, inertial centrifugal force, etc. Proper ultrasonic probes are inserted into the bottom tank to break up the magnetic floes. The performance of magnetite in the complex-forces field is described and the optimal operation conditions are suggested.

Jan 1, 1995

By Alexandru Corneliu Stematiu, Catalin Popescu, Radu Sarghiuta

"The tunnel sector is excavated into a rock mass heavily affected by tectonics, defined as a regional fault. The rock around the tunnel support undertakes the non – elastic deformation and gradually detaches from the rest of the non affected rock mass, moving inside of the excavated area and tending to fill up the whole space. The initial solution of using stiff support consisting in double steel ribs I12 with circular shape in the upper part and straight vertical pillars in the lower part has proved to be inadequate. Based on the calculations of the subsidence phenomena and a mathematical model, the proposed alternative support was provided by special circular steel ribs – SG-23 –that allows a limited rib deformation (by relative slip between the arch segments) in order to mobilize the contact between the rock contour and the inner face of the rib - not only for the deformed rib but also for the neighboring ribs. 1. INTRODUCTION Hydropower development of Jiu river in Romania, in the narrow gorge sector includes two diversion HPP and a small hydro plant that provides the minimum required flow downstream: CHE Dumitra , CHE Bumbesti and MHC Livezeni (Table 1. Hydropower parameters).The Livezeni intake reservoir is provided by a gated dam located 1250 m downstream of merging point between Jiul de Vest river and Jiul de Est river. The dam is equipped with three radial gates with flap gates with a span of 12 m each and the height of (6 + 3) m. The longitudinal profile of Dumitra head and the location of the gallery zone that is the subject of the paper are presented in Figure 2. Longitudinal Profile – Dumitra Head."

Jan 1, 2016

By C. C. Stewart

Jim Walter Resources, Inc. operates four underground coal mines in Alabama. In 1986, during longwall recovery operations, sparks from a torch ignited methane that migrated onto the face after a roof fall. The fire quickly spread to the gob at the tailgate end of the longwall. The fire was successfully "area" sealed and mining operations resumed after five weeks. However, several problems were encountered during this process. This paper describes the events following the fire, methods used to control the situation, problems encountered, and steps taken to ensure preparedness for any future occurrences of this type.

Jan 1, 1993

By John E. Frost

Duval&apos;s (now Battle Mountain Gold Co.) copper and gold deposits in the Battle Mountain District in Nevada are in two subdistricts - Copper Basin and Copper Canyon - about 18 km (11miles) apart. Location of the two subdistricts is shown in Fig. 1. The two centers of mineralization have distinctive geologic and ore characteristics that required different innovative approaches to exploration and development. Nearly all of the copper from Copper Basin has been recovered by heap leaching. Because of relatively high gold and silver values in the Copper Canyon ores, a significant part of the sulfide copper ores has been recovered by a conventional flotation mill at Copper Canyon. Recently, this mill has been converted to the recovery of gold that is mined from zones peripheral to the copper deposits. Prior to Duval&apos;s entry, small amounts of copper, gold, silver, lead, zinc, and antimony had been mined in the district over a nearly 100 year period, beginning in 1866. The bulk of the $13 million total production to 1962 was derived from copper and gold lode ores and gold placers. Duval&apos;s interest in Battle Mountain-arose directly from a submittal by Asarco, which controlled key claims in both the Copper Basin and Copper Canyon subdistricts. Asarco acquired its holdings in the district in 1959 and undertook limited exploration until mid-1961. At that time, the company decided to dispose of its interests. Duval was invited to evaluate Asarco&apos;s properties and accepted. On Dec. 6 and 7, 1961, J.E. Frost, R.C. James, R.W. Sayers, and H.A. Schmitt, representing Duval, and K. Richard and E.W. New- man, representing Asarco, visited Copper Basin and Copper Canyon. Frost concluded that the properties were of considerable interest and prepared, by Jan. 12, 1962, a voluminous report recommending that Duval acquire and explore Asarco&apos;s properties. Furthermore, he recommended a large initial exploration program that included not only geologic mapping, geochemistry, and geophysics, but also the extensive drilling that was to involve, as the first phase of exploration, 49 drill holes in Copper Basin and 21 drill holes in Copper Canyon. Following property agreements between Duval and Asarco, and Duval and several other claim owners, geologic mapping, geochemical surveys, and drilling began in August 1962. Exploration drilling was completed in July 1964 and engineering studies in April 1965. Development of the Battle Mountain properties was authorized in July 1965, and production commenced in the first quarter of 1967. Because of the unusually high oxide copper content of the ore bodies, particularly in Copper Basin, a much larger than typical proportion of the copper in the deposits has been recovered by heap leaching. The generalized geology and ore zones of the Copper Basin are as shown in Fig. 2 and of Copper Canyon in Fig. 3.

Jan 1, 1991

By D. A. Poukhovski

Two integral components of the 30 CFR 48 training requirements mandated for new miners, newly employed experienced miners, and the annual refresher training of all miners are hazard recognition and prevention of accidents. In these categories, instruction shall include the recognition and avoidance of hazards present in the mine, and a review of accidents and their causes. Unlike instruction preparation for fact-based material, program development for hazard recognition places a particular challenge before safety-training specialists because they are often limited in their ability to adequately gauge the trainees&apos; levels awareness prior to training. Further, they must also assure that the training is relevant, and it is presented in a thought-provoking manner. Computer-based instruction is particularly well suited for assisting trainers in developing hazard-recognition topics because it can be used in pre-training and post-training modes for assessment of training effectiveness, in addition to use as a presentation tool. Therefore, this paper will present a recent approach developed at Penn State to apply this technology for assessment and instruction of accident prevention through hazard recognition, with an application prepared for surface coal mines.

Jan 1, 1997

By C. Woofter

Quarry operators must continue to change and adapt environmental compliance methods to meet the increasingly demanding regulations. To fulfill industry needs, a computer-based decision support system is being developed to facilitate decision making that mine operators are required to make regarding environmental responsibilities. This system can help to determine permitting and compliance measures needed for air, surface water, groundwater, noise, aesthetics, vegetation, wetlands, hazardous wastes, storage tanks and wildlife habitats during the development, operation, and closure phases of mining. Operators will utilize the system&apos;s user-friendly interface consisting of mouse driven responses and limited keyboard entries on a desktop computer. The system is easy to upgrade according to the user&apos;s needs and changes in current laws and regulations. Data input models, user interfaces, and support of decision making are explained. The program permits inclusion of the decision maker&apos;s own insights through "what-if&apos; analysis, in which the user can change ad hoc entries and check the related consequences. Using this approach, the user has complete control over all steps of the decision making process. A storm water example is selected to demonstrate the potential benefits of the support system to environmental decision makers.

Jan 1, 1995

By H. Nagel, A. P. Schissler

"INTRODUCTION Anadarko Petroleum Corporation (Anadarko) owns a region of oil shale properties acquired as part of the original Union Pacific Land Grant of the 1800’s in southern Wyoming. These holdings are greater than 2 million acres and occur throughout the Green River Formation in southwestern Wyoming. One area was prioritized for further study by Anadarko Minerals called the Kinney Rim in the Washakie Basin due to low environmental impact, proximity to infrastructure, high ore grade, and low mining cost. The area is a low-overburden oil shale resource that can be developed using surface mining methods, processed by conventional surface retort, and placing waste rock disposal back on the bench for a design capacity of 10,000 barrel per day. The purpose of this papers is to present the results of environmental analysis and timeline, the mine plan, and surface ore processing to offer a resource-ready energy source.Mineral rights for the Kinney Rim area are owned by Anadarko, the United States Bureau of Land Management (BLM) and the State of Wyoming. Mining of oil shale for this study targets Anadarko owned mineral resources.GEOLOGY The study area is in the Green River and Washakie Basins in western Wyoming. The host geologic member is the Laney Oil Shale. Figure 2 illustrates the Laney shale within a generalized lithologic cross section.OIL SHALE LEASING The proposed Kinney Rim oil shale mining project is located in an area dominated by a 1 square mile checkerboard landownership pattern with every other section typically administered by Bureau of Land Management (BLM) and Anadarko. Surface and mineral ownership is a split estate legal entity. The immediate Kinney Rim mine plan is all on Anadarko sections."

Jan 1, 2015

By Karin Bäppler

Lyon with half a million inhabitants is the third largest city in France. Urban agglomerations such as Greater Lyon demand intelligent underground solutions for the freedom of mobility of its inhabitants. The city and metropolitan area of Lyon provide an example of a city strategy adapted to the changing needs due to demographic and living standard trends. The Lyon Metro Line B with a length of 2.4 km is one of the strategic projects with regard to city planning and future mobility. The paper will highlight on this special area of application in singular diverse geology with sophisticated mechanized tunnelling technology.

Jun 13, 2021

By Richard P. Killmeyer, Carl P. Maronde, W. W. Wen, Peter J. Suardini

Under a cost-shared Department of Energy contract, awarded as part of the Coal Preparation Program&apos;s High Efficiency Preparation subprogram, Custom Coals International will be installing and testing a 227 kglhr micronized-magnetite cycloning circuit in PETC&apos;s Coal Preparation Process Research Facility. The project includes the design, construction, testing, and decommissioning of a fully integrated circuit complete with feed coal classification to remove the minus-30-micron material, dense-medium cycloning of the 300 by 30 micron feed coal using micronized magnetite (<10 microns), and medium recovery via drain & rinse screening and various stages and types of magnetic separation. This paper will describe the micronized-magnetite beneficiation technology and the scope of work for this project including an update on the status of the project, the circuit, and the proposed test plan.

Jan 1, 1995