Search Documents

A Directory of Computer Programs Applicable to US Mining Practices and Problems. A. L. Sanford, T. L. Myers, and J. F. Stiehr. USBM OFR 131-78, Nov. 1977. A Master Environmental Control and Mine System Design Simulator for Underground Coal Mining. Tape MDS-5. Pennsylvania State University. USBM CT 1.77, Dec. 1975. Contains computer programs on a dynamic general purpose computer simulation model for underground coal mining. A Method for Computing Stabilization Pressures for Excavations in Incompetent Rock. J. D. Dixon and M. A. Mahtab. USBM RI 8128, 1976. Describes technique for determining the confining pressures that must be provided for stabilizing underground openings in incompetent rock. Accident Cost Indicator Model to Estimate Costs to Industry and Society From Work-Related Injuries and Deaths in Underground Coal Mining. Vol. I.III. D. G. DiCanio, A. H. Nakata, D. Colvert, and E. G. LaVeque. OFR 39(1)(3)-77, Dec. 1976. Describes a computer-based model for estimating the tangible costs of injuries and deaths from work-related accidents In underground coal mines. An Interactive Computer System for Evaluating Coal Mine Illumination. R. Goldstein. USBM OFR 110-80, March 1980. Computer system for calculating the illumination on coal mine surfaces due to machine-mounted lights. Analytical Modeling of Mine Roof Behavior Using Statistical Material Properties. R. T. Langland and F. J. Tokarz. USBM UCRL-51876, Aug. 1975. Analytical study of coal mine roof behavior using a computer model of a room-and-pillar mining method. Application of a Total System Surface Mine Simulator to Coal Stripping. Vol. I-VII. Pennsylvania State University. USBM OFR 33(1)(7)-78, Aug. 1978. Describes model development, input and output documentation, three case studies of an open-pit materials handling simulator, and development of two equipment selection models and a cost model. Characterization of the Structural Behavior of Rock Masses. Vol. I-II. L. R. Herrmann and M. A. Taylor. USBM OFR 67(1X2)-75, Sept. 1974. Computer subroutines for characterization of rock behavior, Including variability of properties within the rock mass, planes of weakness orthotropy, strength criteria, and post-failure behavior. Coal Mine Electrical System Evaluation. Vol. I-VII, L. A. Morley, et al. USBM OFF! 61(1)(7)-78, 1977. A concept to improve underground coal mine electrical system safety and availability. This proposed technique is based upon the ability to predict incipient failures in the mine power system. Prediction is made possible by a new method which uses a minicomputer to implement pattern recognition algorithms. Computer Modeling of Fluid Flow During Production and Environmental Restoration Phases of In Situ Uranium Leaching. R. D. Schmidt. USBM RI 8479, 1980. Describes development and application of a computer model for simulating the hydrological activity associated with in situ leaching. Interpretation of Rock Mechanics Data, Vol. II (A Guide to Using UTAH2). W. G. Pariseau. USBM OFR 47(2)-80, June 1978. Brief description of a two-dimensional elastic-plastic finite element program intended for mine stability analysis. Iterative Approximation Techniques for Microseismic Source Location. G. H. Dechman and Meng-Cherng Sun. USBM RI 8254, 1977. Iterative approximation method for microseismic source location developed to adapt microseismic techniques for rock structure analysis to investigations of surface problems such as slope failure in an open-pit mine. Limits and Cost Sensitivity of Alternative Parting Handling Methods. Vol. I-II. T. E. Finch, D. R. Haley, and C. J. Speaks, Jr. USBM OFF! 117(1)(2)-77, March 1977. Programs to examine alternative methods of handling the parting between two coal seams in a surface mining operation. Alternative methods consist of equipment implementation in either a stowing or haulback technique. Methane-Water Flow in Coalbeds. H. S. Price. USBM CT 1-79, April 1972. This computer program calculates transient, two-dimensional, gas¬water flow in a porous medium. Plastic Canopy-A Computer Program for the Structural Analysis of Protective Canopies. K. D. Winters, G. A. Gavan, and J. C. Ault. USBM IC 8795, 1979. Presents a FORTRAN IV program for the structural analysis of protective canopies used In underground mines and rollover protective structures used in surface mines. The Three-Dimensional Structural Analysis of Double-Entry and Single-Entry Coal Mines. Vol. I-III. Agbabia Associates. USBM OFF 16(1)(3)-80, Oct. 1978. Describes the computer program designed to perform a three-dimensional finite element analysis of an instrumented section of double- and single-entry coal mines. Underground Mine Evacuation Plans Analyzed by Computers. D. Tesarik, D. Nicholson, and A. B. Boghani. MSHA, Vol. 4, No. 5, Oct. 1979. USBM has developed a computer program to evaluate and construct mine evacuation procedures and plans.

Jan 11, 1981

By Fred Leighton

Miners have long known that rock noise, or the popping and cracking of the rock commonly heard during mining, can indicate instability of the mine structure. For many years, miners have "listened" to the rock talk and many times have interpreted changes in rock noise activity to be a warning of failure and have retreated from the potential failure area. Microseismics, or the study of rock noises, was begun in the early 1940s partly because of this historical fact. Microseismics is based on using geophysical equipment to detect and analyze rock noises on audible and subaudible levels. Thus, these systems are much more sensitive than the human ear and "hear" even more of the rock "talk" than do miners. Research has shown that micro-seismics can be used to precisely locate portions of a working area that are generating rock noise, and that rock noise release rate information from each area can be used to analyze its stability. On the basis of research results, microseismic systems are now commercially available and have been purchased and installed in many mines around the world. Introduction When a rock mass is subjected to changing stress conditions, such as those caused by mining, small-scale adjustments occur within the rock that release seismic energy. When this energy is in the audible range it is called rock noise. Those areas where stress changes occur are also the areas of the structure most likely to fail. Individual rock noises can be detected and analyzed to determine their precise location relative to the mine structure. Over a period of time plots of this data provide a pictorial representation of where stress changes are occurring. This is because rock noise activity tends to concentrate in those structure areas most actively adjusting to the changing stresses. Since these areas are the most likely to fail, they can be pinpointed and mapped relative to the structure. Rock noise rates, or the number of rock noises occurring per unit of time, also tend to vary dramatically before failure. Thus, the ability to locate the source of individual rock noises provides a means of determining where failure may occur, and rate counting within each area offers a means of assessing when failure may occur. This information, properly treated, can be used to avoid, control, or warn of impending failure. Successful applications of this technique have provided recent impetus to the effort of developing microseismics into a practical, reliable, and economically feasible tool. The phenomenon of naturally occurring rock noise was discovered in 1938 by Obert and Duvall (1939) who were measuring seismic velocities in mine pillars. Seismic energy other than what they were generating continually registered on their recording equipment. Further study by these researchers showed that the extraneous seismic energy being recorded was from rock noises that were being generated within the rock in highly stressed areas. Pursuing this interesting phenomena both in the laboratory and in the field, Obert and Duvall documented the dramatic change in rock noise rate before failure (Obert, 1941). They also established the fact that, in many instances, rock burst failures could be predicted by monitoring and listening to the rock noise activity in rock-burst-prone areas (Obert and Duvall, 1945). These early efforts clearly showed that microseismics had great potential as a tool for measuring or estimating mine structure stability. Extended testing, however, showed that sometimes rock bursts occurred with no apparent microseismic warning, and that at other times sharp increases in microseismic data were not accompanied by failure. Also, because precise location of individual rock noises was not possible at that time, one never knew where the failure was going to occur, only that failure near the observation point was likely. Thus, while the technique clearly offered promise, it was not considered practical then. In the mid-1960s, the Bureau of Mines undertook a new research effort to improve the microseismic technique. Major improvements were judged possible mainly because new and vastly improved electronic and system components had become available as an offshoot of space program instrument development. Thus, in 1967, development of a multichannel, broad band, microseismic system began (Blake and Leighton, 1970). Application of this system in rock-burst-prone mines showed it worked well and provided the incentive to develop methods whereby the source location of individual rock noises could be easily and directly calculated (Leighton and Blake, 1970; Leighton and Duvall, 1972; Redfern and Munson, 1982). The improved system and the ability to locate rock noises quickly showed that the microseismic technique offered new and increased poten-

Jan 8, 1983

By C. J. Johnson, C. J. Bise

Coal extraction by continuous miners (CM) is currently the most common underground method in the US industry and accounts for slightly more than two-thirds of the nation's deep mining production (National Coal Association, 1987). Even if longwall mining should become more commonplace, it can proceed only after ventilation and access entries have been driven by CMs. Since an area of concern continues to be the effects of the dust generated on the health of mineworkers, this paper discusses the relationship between the elemental compositon of mining-generated airborne dust sampled from the immediate ventilation return of a CM and laboratory-generated dust derived from channel samples taken from the mines. There are several potential contributions of this type of study to the coal mining industry. First, after more fundamental knowledge of the causes of Coal Worker's Pneumoconiosis (CWP) is learned, the laboratory-generated respirable dust could be used to identify a potentially hazardous coal seam. Also, this study could possibly aid in understanding the fundamental causes of CWP by producing mining-simulated samples of coal dust that could be used in epidemiological studies. Further. assuming that there is no difference in the elemental composition of a drill-core sample and a channel sample from the same location, a mining company could predict anew mine's respirable dust elemental composition in the immediate ventilation return by using exploratory drill core samples of the roof, coal, and floor rock to prepare the laboratory dust. Ventilation engineers could then use engineering design and control measures during premine planning to reduce the incidence and severity of CWP by better ventilating the potentially hazardous coal seam. If this proper planning prevented any future changes to the ventilation equipment and mine design. much time and money could be saved. Scope of work To investigate the variability of the chemical characteris tics of respirable dust, airborne dust samples from eight underground coal mines located in the eastern and midwestern United States were collected with eight-stage Sierra Model 298 Marple cascade impactors, as well as 25 channel samples of mined material. Each channel sample was removed from the middle of the coal face before mining occurred. Sampling of the mining-generated dust was conducted by Lee (1986) by sampling the entire working sections, primarily for characterization purposes, to obtain information on the locational variability of dust characteristics. Research performed for this study used the elemental analyses of the mining-generated dusts he sampled in the immediate ventilation returns of CMs. The procedure that was used to produce the laboratory generated respirable dust was based on the Hardgrove grindability test since it reflects the pulverizing characteristics of coal. This test was chosen for several additional reasons. First, it is repeatable and reproducible. A consistent amount of input energy is used as well as a specified size range of feed material to be crushed (the channel samples). Second, it is thought to generate secondary dust in a way similar to that of the crushing and grinding of the coal and rock as they pass through the arc-shaped cutting path of the CM's cutter head. The potential effect on dust generation by this secondary grinding mechanism may be at least as much as that produced by primary fragmentation, which is dust produced by the cutting action of the bit against the coal or rock (Roepke. 1984). Finally, the Hardgrove grindability test is well known and is used in the coal industry to guide mineral processing engineers in estimating the capacity of mills used to grind coal. One hypothesis of dust researchers in the Generic Technology Center for Respirable Dust is that the elemental as well as the physical characteristics of coal mine dust will make a difference in the incidence and severity of CWP. Coal mine dust is generated not only from coal, but also from any rock partings contained within the seam or any roof or floor material mined with the coal. Thus, coal mine dust may not have the same elemental characteristics as the coal being mined. Given that hypothesis, mixtures proportional to each thick¬ness mined of roof, coal, and floor rock derived from the channel samples of the face areas from which the respirable dusts were generated by the CMs were used to produce the feed material that was pulverized in the Hardgrove machine.

Jan 1, 1990

By H. O. Seigel, John C. Robbins

Luminex is a new method of prospecting for mineral deposits based on time-resolved mineral luminescence created by an ultra-violet light source. Developed by Scintrex Ltd., Luminex detects and resolves a group of key minerals - either ore minerals themselves or, more often, accessory or pathfinder minerals for certain types of economic ore deposits. These minerals are commonly found on the earth's surface, even in areas of considerable weathering. The method extends the range of mineral deposits that are remotely detectable from the air. Tungsten, tin, molybdenum, gold, and bedded lead-zinc deposits are included. Therefore, Luminex is a natural supplement to the three classical methods of airborne geophysics. The luminescence of minerals has been known and used qualitatively in mineral exploration for many years. But there are more than 500 minerals known to be at least sometimes luminescent. Luminescence of most is unpredictable and the colors they emit may vary from locale to locale. It is, perhaps, this apparent complexity of the field that has discouraged its proper scientific scale until now. There are two basic types of luminescent minerals - intrinsic and impurity activated. In the first type, luminescence is an inherent property of the mineral in its purest form. In the latter, luminescence is due to the introduction of foreign trace elements, often in very modest amounts (ppm), into the crystal lattice. These trace elements are known as activators. There are very few intrinsic luminescent minerals commonly found in nature. Chief among these are the calcium tungstatemolybdate family, more commonly known as the scheelite-powellite family, and the uranyl minerals such as autunite and saleeite. The vast majority of other known fluorescent minerals such as fluorite, hydrozincite, and many calcites, are impurity activated - that is, they will not fluoresce in purest form. In addition to the many minerals likely to luminesce at the earth's surface under ultraviolet excitation, any prospector who has ventured out at night with a mercury lamp will know that much organic matter luminesces - for example lichens and even scorpions. Just as the eye finds difficulty in resolving the luminescence of minerals from that of organic materials, it also has its limitations at sorting out minerals from one another by their luminescent colors. Figure 1 shows, in part, the photoluminescent emission spectra of scheelite, hydrozincite, and autunite. It is clear that there is a considerable similarity in spectrum between scheelite and hydrozincite and a great deal of overlap. In fact, a small amount of molybdenum in the scheelite lattice can almost bring these two spectra into coincidence. On the other hand, the autunite emission spectrum is clearly resolved from the other two. Basis of the Method The right-hand side of Fig. 1 shows the time waveforms of decay of the photoluminescence of the same three minerals. It is apparent that the lifetimes of photoluminescence of scheelite and hydrozincite are radically different and that these two minerals, therefore, may be readily resolved through their emission lifetime characteristics. It is in the realm of time-resolved measurements (lifetime characteristics) that Scintrex has made its major advance in the Luminex method. With the exception of some work by Exxon confined to uranyl minerals, to the best of our knowledge, no systematic scientific investigation has been carried out in the field of time-resolved mineral luminescence studies other than the work of Scintrex. Scintrex's findings are that all organic materials and most commonly activated luminescent minerals have lifetimes shorter than one microsecond. In addition, only a relatively small number of minerals - among them those called key minerals, or certain ore and pathfinder minerals - have lifetimes greater than one micro-second. Scintrex is able to characterize these minerals primarily by their emission lifetimes and secondarily by their emission spectral characteristics. By a combination of these factors a mineral index is arrived at. From that, photoluminescent minerals can be resolved from one another with a high degree of probability. At least two spectral channels and two time channels - of which one can be common - are required to apply this mineral index. Ground System A portable hand-held Luminex analyzer based on a modulated mercury lamp has been used to date in Canada, the US, and Australia. The current production model of this device is the LG-2. It has two spectral channels and two time channels for each spectral channel. Figure 2 shows a ground Luminex traverse over the Texas-Arizona zinc prospect in Arizona. The instrument was set so the channel read was hydrozincite-specific insofar as possible. The mineralization in this prospect is known to be hydrozincite and other zinc secondary minerals in limestone. Figure 3 shows a ground Luminex traverse over the AAA uranium prospect in Nevada. The instrument was set to optimize the uranyl response. For comparative purposes, broadband scintillation counter readings were made on the same stations (also shown in Fig. 3). It is apparent that both the Luminex and the scintillation counter results reflect a near-surface distribution of uranyl minerals. It is interesting that no visible uranyl secondary minerals

Jan 7, 1983

By Robert W. Miller

There are many problems faced by ventilation engineers in deep underground mining operations, not the least of which is controlling miner exposure to radon gas and its daughter products. Radon gas is commonly found in uranium mining operations, but may also be present in other deep metal mines. For example, tin mines in England, iron ore mines in Sweden, gold mines in South Africa, and molybdenum mines in the U. S. have potential radon exposures. This is because uranium and accompanying radium ore are ubiquitous to the earth's crust albeit at low levels. The fact that the activity represented by one WL can be caused by a relatively low concentration of radon gas increases the difficulty of control. Since the source of the radon gas is usually widespread throughout a mine, local exhaust ventilation is not a viable control schema. The technique used to control exposure is then dilution ventilation and, in fact, huge amounts of air must be moved in order to reduce potential exposures to an acceptable level. An interesting comparison can be made of ventilation rates in different types of mines. It is estimated in modern coal mines, which are generally acknowledged to have high rates of ventilation, that about eleven tons of air are moved for each ton of ore mined. A typical operating uranium mine may have ventilation flows of 14-15 tons per ton of ore mined. This provides an idea of the scope and importance of ventilation in modern mining operations where radon is a hazard. Further pressure is put on ventilation engineers by the steady downward trend in exposure limits set by national and international standard setting agencies. Much of this tendency toward lowered standards is based upon longitudinal mortality studies of miner populations. Another important factor is the limited number of experienced miners available in the labor pool. For optimum production, it is important to have as many experienced miners underground in each shift as possible. However, the average daily exposure in a U. S. mine must be less than .3 WL to permit the miner to work underground for a full year. The ventilation system then must provide enough uncontaminated air to maintain the WL below the .3 TTL level to maximize production efficiency and minimize personnel turnover and the problems associated with it. Ultimately, the goal of the ventilation engineer and health physicist is to protect the working miner from harmful exposures based upon currently acceptable standards. U. S. Federal regulations require that in uranium mines all active work sites must be monitored every two weeks if they measure above .1 WL. Areas that have .3 WL ratios or higher must be monitored on a weekly basis until five consecutive weekly samples show the level has dropped below .3 WL. Also, exposure records must be kept for all individuals exposed to levels exceeding .3 WL. These requirements provide a strong economic incentive to have a ventilation system that minimizes exposure of any personnel. A good ventilation system requires careful planning, operation and backup in order to fulfill its mission of providing adequate clean air. Its proper operation also requires coordination with production personnel so it can be adapted as new areas in the mine open up and old areas are sealed off. The ultimate indicator of ventilation efficiency to control radon daughter exposure is, of course, monitoring working levels. Historically, this has been done using the Kusnetz, Tsivoglou, and Rolle's methods, among others. These methods all require cumbersome equipment and tedious calculations to obtain the measurements that results in WL. More important, however, they require a significant time lag between sampling and counting, typically 40-90 minutes. This time lag is, in fact, what can cause significant economic losses due to unnecessary downtime as well as high WL exposures. In a typical mining situation, a sampling technician using the Kusnetz method takes a sample, moves to the next location and takes another sample and so on. Forty to ninety minutes after the first sample, the technician will stop, run the activity count on the filter and calculate the WL. The technician may be one-half mile away or several levels removed from where the first sample was taken when it is counted. If the WL ratio is high the technician must then backtrack to the sample position. There are then two options. If the sample area is a working stage, it can be shut down or a second sample can be taken. If the first alternative is chosen; i.e., shutdown and correction of the ventilation, then another sample must be taken, followed by a forty minute wait for results. If the ventilation adjustment didn't correct the problem, then the whole process must be repeated with a minimum of forty-five minutes per sample cycle when using the Kusnetz method. It has been estimated from operating uranium mines that the cost per hour for downtime on a production slope is about $1,50O/hour. The time lag between sampling and resultant data can be very costly. If the second alternative is chosen to verify the first reading, the miners may be unnecessarily exposed to high levels while waiting for the result. Clearly, such a sampling system can be markedly improved by eliminating the excessive time lag between sampling and analysis.

Jan 1, 1981

By B. P. Boisen

INTRODUCTION The rapidity of onset, rate of increase, and magni¬tude of loads in an underground support system can be measured using load cells or pressure cells, whichever is appropriate to the type of support. These instruments should be installed at the various instrumented station locations immediately after excavation. If the loading of a member is of interest, the load should be measured, whereas if the deflection or strain of a member is of interest, the strain should be mea¬sured. It makes as little sense to use a load cell to allow computation of strain as it does to measure the strain and then back calculate the load. Tunnel steel set de¬signers today invariably rely on the early work of Karl Terzaghi, the basis for which is load, so load measure¬ment should be the main concern. The current trend of using strain gages on steel sup¬port systems stems from the inability by some to eval¬uate unusual loading conditions caused by uneven block¬ing. In fact, uneven blocking will obscure almost any attempt (whether with load cells or strain gages) to properly evaluate support performance. The load curve in Fig. I shows the development of a characteristic early peak load sometimes called the "rear abutment load" seen in many underground open¬ings. It is thought that the peak reflects the coupling of the rock and the support system, and that the magnitude will increase until some yielding, or minor failure, of the support system occurs. At that time, the slight deforma¬tion of the support system promotes the formation of minute shears in the opening walls, and these shears tend to distribute stress between the support system and the adjacent rock in proportion to the relative rigidity of the support elements and the rock. In normal rock, as a result of this stress redistribu¬tion, subsequent load magnitudes generally do not reach the magnitude of the early peak load. In physically unstable (squeezing) or chemically un¬stable (swelling) rock, however, the loads experienced after passage of the early peak load may in fact show a slow, continuous increase. One of the very important purposes of load instrumentation is to provide the means for recognizing such long-term adverse trends, thus enabling the proper remedial steps to be taken. Another purpose of load instrumentation is to pro¬vide a comparison between the magnitudes of the early peak load and the subsequent stable load. The ratio of these two loads is analogous to a safety factor, and may be used to evaluate the efficiency and economy of the support system design. Aside from considerations of economy, it may be well to design support systems which do not have excessively high ratios of early peak load to subsequent stable load. Should these ratios be exces¬sively high, the support system may be so rigid that the yield or failure associated with stress redistribution may occur with explosive violence. Load cells for use in mines, tunnels, and on con¬struction projects come in many forms. Almost all, however, employ the same procedures for installation, readout, etc. Therefore the following comments are almost universal in application. LOAD CELL INSTALLATION Load cells should be installed with bases parallel to the surfaces against which they bear. Care must be taken to orient the cells so that their signal cables are protected from accidental damage as a result of con¬struction, maintenance, or cleanup activities. Most electronic load cells are compensated for tem¬perature variations likely to be encountered during nor¬mal operations. However, if a large difference is an¬ticipated between the calibration temperature [21°C (70°F)] and the average operating temperature, the cells should be conditioned to the operating temperature for at least 8 hr prior to installation. This is to insure that the initial reading, made under no-load conditions prior to installation, provides a stable value to which subse¬quent measurements can be referred. Hydraulic load cells tend to be temperature sensitive and should be used with that in mind. Also, hydraulic load cells tend to be soft compared to electronic types and will sometimes allow movement to take place in a system intended to be semirigid. Furthermore, hydrau¬lic load cells tend to be difficult to read remotely. Care must be taken to use bearing plates on both sides of load cells which are sufficiently rigid and of high enough bearing capacity to prevent bending and crush¬ing under load. This is very important with tieback load cells (basically a ring of steel) which can easily dig into bearing plates. MAINTENANCE AND TROUBLESHOOTING Except for a direct hit by a miner's axe or flyrock from a blast, most hydraulic load cells are nearly in¬destructible and require little, if any, maintenance. Hy¬draulic oil on the bearing plates is a good indication of a leak and the need for corrective action. Field maintenance of electronic load cells involves protecting the instrument and signal cable from mechani¬cal damage and from unnecessary exposure to dirt and moisture, and recognizing and correcting damage and the effects of normal wear and tear.

Jan 1, 1982

By Stanley Ferguson

Since 1978, the Colorado Department of Health has become involved in specific investigations of possible radiation hazards among nonminers in Colorado communities. In each instance, the improper disposal of mill tailings has precipitated concerns and allegations of radiation hazards. This presentation is a brief summary of the findings, to date, of 4 such investigations involving tailings disposal problems in Canon City, Denver, Durango and Grand Junction, Colorado. Canon City In the summer of 1979, allegations of excessive cancer incidence were made at public hearings concerning an application for a Radioactive Materials License submitted to the Colorado Department of Health by the Cotter Corporation for a uranium mill at Canon City. Canon City is the site of a uranium mill operated since 1958 by Commonwealth Edison. Local residents accumulated figures and calculated rates suggesting a 2-fold excess in total cancer mortality. These rates were not adjusted or standardized for demographic varibles. A review of cancer mortality data and computation of age standardized rates for years 1950 through 1977 showed that Canon City's cancer mortality rates were within expected limits, actually lower than rates for the State of Colorado or the United States. The first slide shows rates for every fifth year, 1950 through 1975. Further, an analysis of Canon City cancer incidence data from the Colorado Central Cancer Registry revealed that 1979 incidence rates were not significantly different from Colorado rates, with the exception of prostate cancer. The next slide shows age standardized incidence rates for lung, colon, breast and prostate cancer. Data were also reviewed for leukemia, myeloma, lymphoma and cancers of the thyroid stomach, uterine certix, ovary, kidney, bladder-and brain, however, small numbers of cases prevented meaningful rate calculation. 1980 data are presently being analyzed. None of the data yet examined support allegations of radiation-associated cancer in Canon City. Denver In February of 1979, the Department of Health became aware of a number of radium mill tailing deposits in the Denver metropolitan area, remnants of the radium milling industry of the early 1900's. Several of the deposits were situated so as to possibly contribute significantly to radiation exposure of a small number of people over a period of several decades. The Department developed protocols for radiation surveys, dosage estimates and, for a small number of persons, body burdens determinations and peripheral blood lymphocyte cytogenetic studies. The results of this investigation suggested no measurable biomedical impact as a result of the radium deposits. Durango In October of 1979, a physician residing in Durango, Colorado released information from a preliminary analysis of lung cancer data suggesting an incidence rate several times expected in that city. The data were presented at a meeting of a citizen's group concerned about the possible health hazards of 2 uranium mill tailing deposits located in the south end of the city. Since cancer incidence data generally do not exist in most of western Colorado, a team of epidemiologists was dispatched to Durango to work with local physicians and hospitals in conducting an epidemiologic study of selected cancers for the period 1969 through 1978. After case-finding and record abstracting were completed, it was determined that sufficient data were available for study of only 3 sites: lung cancer, breast cancer and leukemia. The next slide shows age standardized incidence rates for these 3 sites for 1969-1978 for Durango and the State of Colorado. There are no significant differences in these rates. The data did show a geographic peculiarity with regards to the relative proportion of tumor types near the tailings deposits as opposed to away from the deposits, however, this finding is based upon very small numbers of cases and may represent only the random excursion of rates based upon small observations. This investigation suggests that if a carcinogenic hazard is present, it is too small to be detected by the study method employed. Grand Junction The Department of Health has been involved in the Grand Junction mill tailings problem for several years. In 1966, the Department issued an order terminating the practice of free public access to a 55-acre pile of uranium mill tailings. Prior to this order, an estimated 300,000 tons of material was removed. Of this amount, an estimated 50,000 tons was presumably used in residential and commercial construction. Despite many allegations of cancer and birth defects excesses in Grant Junction since the mid 1960s, the first epidemiologic study of cancer was conducted in the spring of 1977. Data from the Colorado Central Cancer Registry were analyzed and reported to the Executive Director of the Department of Health in June of that year. The findings of the first and preliminary study were an unexplained excess of acute leukemia and chronic myelocytic leukemia. The excess was based upon small numbers but was present across all age groups. No increase in chronic lymphocytic leukemia was evident.

Jan 1, 1981

By J. E. Oberholtzer, M. G. Fernald

INTRODUCTION Approximately six years ago the U.S. Bureau of Mines (USBM) developed a data acquisition system (DAS) specifically designed for measuring radon levels and other environmental parameters during studies of means to control radiation hazards in underground uranium mines. The DAS system records data in machine readable form using a paper tape punch, which represented the state-of-the-art at that time for a moderate cost output device. However, the use of paper tape as a recording medium for field studies is somewhat unwieldy. Reducing the raw data required either that the tape be shipped to a computer center equipped with a high-speed paper tape reader or that the tape be transmitted at low speed over the telephone lines to a remote computer. Transmitting, at ten characters per second, the data from a 10-channel DAS taking Four readings per hour would require about 30 minutes For each 24-hour day's data. Telephone lines from remote mine sites are often of marginal quality and data errors can be introduced during transmission. Paper tape punches are also prone to occasional punching errors. Both problems make it necessary to carefully check for and correct data errors, a process which is possible because each DAS produces an independent printed data record, but the error checking and correction process can be quite laborious. Aware of recent advances in microcomputer technology which have brought the price of a personal computer down to about the cost of a paper tape punch 5-10 years ago, the Bureau decided to explore the feasibility of using a low-cost personal computer in the field to process DAS data in real time. On behalf of the Bureau, Arthur D. Little, Inc., developed a simple interface circuit which permits an Apple II computer to accept data from one or two DAS units as it is being transmitted to the paper tape punches. Computer software converts each measurement to appropriate engineering units, e.g., radon concentration, Working Levels, air velocity, temperature, or barometric pressure. The computer also calculates 1-hour and 8-hour running averages of all converted data and prints those results as soon as they are obtained on a line printer located at the test site for immediate inspection. After development, the system was used continuously and successfully for a 5-month period at a Utah uranium mine. DAS DESIGN AND MODIFICATION Each of the two USBM data acquisition systems used in this work consists of two separate modules. A multiplexer module located below ground near the measurement transducers acquires signals from each of nine tranducers. Six input channels were devoted to measurements of radon or Working Level. The outputs of those transducers, photomultiplier tubes or G-M tubes, respectively, are digital pulse trains which are accepted directly by the mutliplexer. Three channels were used for environmental parameters--air velocity, temperature, and/or barometric pressure. Each of the environmental tranducers is fitted with dedicated linearizing and voltage-to-frequency conversion circuitry so that the outputs to the multiplexer are also pulse trains having frequencies of one tenth of the value of the measured parameter expressed in the appropriate engineering units. A 100-Hz reference signal was input into the tenth channel for use in monitoring system integrity and performance. All ten pulse trains are then timeseries multiplexed into a signal line for transmission to the above-ground data acquisition module. Above ground, the composite signal is de-multiplexed into ten separate lines, each of which is connected to a digital counter which converts the pulse train to a numerical value. The acquisition of each set of readings is initiated by an adjustable "scan cycle comparator" timer. The acquisition process proceeds in three phases. First, radon and Working Level channels are counted for an extended period of time, typically 5-10 minutes depending on activity, because of the low pulse rates involved. Then the other four channels are counted for ten seconds, and finally, all ten readings, along with the Julian day and time of day are output serially onto paper tape and printed on a strip printer. When the scan cycle comparator reaches its preset time (15-minute cycle times were used in this work), it resets itself, initiates another readout cycle, and begins timing again. The only modification made to the data acquisition systems used in this work was to disconnect the scan cycle comparator in one unit, which became the "slave" and bring in the scan cycle comparator signal from the other unit, the "master", to initiate data acquisition cycles in the slave. Synchronizing the two data acquisitions in this fashion and using two slightly different radon counting times insured that the two systems never attempted to output data to the Apple II at the same time. THE APPLE II COMPUTER The Apple II computer used in this work was equipped with 48 KBytes of semiconductor random access memory (RAM), two floppy diskette drives, a Centronics Model 730 impact matrix printer and a modulator for driving an ordinary color television as a video display device. A single California Computer Systems Model 7720A dual 8-bit bidirectional parallel input/output (I/O) card was installed in the Apple to accept the digital data from both data acquisition systems. This card is

Jan 1, 1981

By Thomas J. DeMull

Heap leaching was introduced to the precious metals mining industry approximately two decades ago as a simple, low cost method for recovering gold and silver from ores. Since that time, operational experience has contributed to knowledge and understanding of the process, making it a reliable alternative to conventional milling processes for low grade ores. At time of this writing, dozens of heap leach operations are active producing hundreds of thousands of ounces of gold and millions of ounces of silver annually. These successes have caused the popular press to acclaim heap leaching "high-tech" gold mining, but, despite the hype, the process remains a simple one. An example of simplicity in heap leaching is the operation established in 1986 at Amax Gold's Sleeper Mine. Starting with a simple goal, namely to produce gold from sub-mill grade ore at low cost, heap leaching was rapidly implemented at Sleeper; only five months after testwork started, leaching commenced on the first commercial scale, 50,000 ton heap of low grade ore. Sized at 600,000 tons per year to produce 10,500 oz gold per year, the low grade heap operation has performed beyond expectations. During the first year of production, 881,800 tons have been leached producing 15,665 oz of gold and 35,528 oz of silver. Operating ·costs for the first year have averaged $112 per oz gold produced ( or $95 per oz if silver credit is included). Successful implementation of heap leaching at Sleeper has had a dramatic impact on ore reserves and future operations.

Jan 1, 1998

By S. A. G. Poppen

The lining of a mine shaft is one of the most important considerations in the planning and operation of an underground mine. Generally, the function of a shaft lining is to preserve the shaft opening in a manner compatible with the expected mine life and -the other shaft operations. Where shafts are the only means of surface access in a mine, they also serve a critical function for the safety of the entire underground operation. Routine repairs and maintenance work on the shaft linings are only possible in stable strata with only minor interruptions to the shaft operations.

Jan 1, 1988

By Alan C. Noble

Ore reserves are often less than 30% of geologic resource estimates that are initially prepared by exploration geologists. Differences of this magnitude between resources and reserves can lead to serious . problems in the early valuation of properties when the geologic resource estimates are interpreted to represent ore reserves and are later found to be misleading and gross overstatements of ore reserves. The geologist can avoid such difficulties by considering the implications of mining, metallurgical recovery, and economics early in the project and by using appropriate qualifiers in the resource statement Examples using typical deposit characteristics are used to demonstrate how cutoff grade, stripping ratio, dilution, mining extraction and metallurgical recovery affect ore reserve estimations.

Jan 1, 1992

By M. E. Lewellyn

A lower moisture content for a clean coal product means increased Btu content, or increased yields at the same Btu content, and lower operating costs. The conventional surfactant-based dewatering aids effeciently lower the moisture content but often the presence of residual surfactant in the filtrate and recycle water causes problems downstream. ACCOAL-DRI 1000, a surfactant-based dewatering aid, was developed to solve this problem by minimizing the downstream effects while efficiently lowering the moisture content. The theory of the use of surfactants in filtration will be discussed as well as the development and field evaluation of this new product.

Jan 1, 1988

By Jeffery L. Kohler

A method of monitoring production, information, i.e., raw tonnage and machine state, from each working section has been developed. The method is based on the sensing of electrical parameters in each section load center, and the reporting of this information through the existing mine-wide monitoring system. A decision-theoretic type of pattern classification technique has been used to define the machine states. The basis of the method is presented in this paper, along with a proposed hardware and software implementation scheme. Information issues central to the development and use of the proposed production monitoring system are also discussed.

Jan 1, 1988

By R. W. Hagemeyer

By way of background. it is important to keep in mind that the information presented in this paper relates specifically to synthetically produced precipitated calcium carbonate (PCC) fillers. Natural calcium carbonate fillers manufactured by grinding limestone, marble and chalk, though having similar chemical and physical analyses to PCCs, normally contribute somewhat different performance properties in paint, paper and polymer systems. Many factors have been cited and numerous theories have been proposed for the observed differences. Particle size parameters, surface chemistry and particle morphology are the items most frequently mentioned. A discussion of this subject is beyond the scope of this paper.

Jan 1, 1989

By A. MacG. Robertson

Where weak rock zones are encountered in the slopes of an open pit, they may control pit wall stability. Back analysis of slopes involving failure through weak rock enables an estimate to be made of the weak rock strength. A system of consistent rock mass classification is described which enables the weak rock mass material to be described and classified from drill hole core. Correlation with back analysis determined strength allows strength estimates to be assigned to each rock mass classification.

Jan 1, 1988

By A. R. Przybylek

A fluid bed dryer has been designed for a nonconventional application to upgrade the value of fine anthracite culm and silt recovered from culm banks and anthracite tailings pond beds. This material can be seen as large spoil piles scattered throughout the anthracite coal regions of Eastern Pennsylvania. Engineering of the system commenced in December of 1986 and at this writing start-up is scheduled for late October or early November of 1987. This paper will focus on generalities concerned With system design and operation, and qualify the differences from conventional fluid bed coal drying systems.

Jan 1, 1988

By G. M. Bernard

An overview presentation of the fast-track start up of Cerro Colorado, a new copper heap leach project in Chile's Atacama' desert. A brief explanation 'of location of the property, exploration history, geol-ogy, reserves and development are presented. The overview includes mining, crushing, agglomeration, and the solvent extraction-electrowinning recovery process. Challenges and requirements specific to heap leach systems will be addressed and analyzed. A detailed description will be given of the mobile heap leach conveying and stacking systems used in the building of heaps for on-and off-pad operations.

Jan 1, 1995

By P. W. Hynes

Tg Soda Ash has operated a shortwall mining system in the Green River, Wyoming trona district since August. 1982. The system has proven to be highly productive. In an effort to reduce the relatively expensive development mining and Improve mine planning flexibility, a method to mine the return air tailgate during the shortwall retreat was tested beginning In April, 1987. As of June. 1988 four shortwall panels had been completed utilizing the advancing tailgate, producing over 815,000 tons.

Jan 1, 1989

By C. E. Jordan

The Bureau of Mines conducted research to measure the improvement provided by fine bubbles on the flotation of fine-sized particles (minus 20-um size) in an effort to improve flotation efficiency in our domestic minerals industry. The turbulent velocity distributions of the fluid within the flotation cell were measured as a function of time and position and used to increase the precision of a fine particle, turbulent flotation model. For the mineral system investigated, improved flotation response was obtained under laboratory conditions by using small bubbles and intense agitation. These results matched the model's predicted response.

Jan 1, 1989

By R. W. Guill

For the past five years, Small Mine Development has been involved in the development of small grade underground projects. These projects have been in tough environments where solutions have been found by placing emphasis on creative collaborations by small work forces and selected specialists. This has created an environment where constant innovation and change have become standard operating practice. The cornerstones of these efficient operations have been formed using pneumatic backfill, creative shotcreting, specialized equipment, and highly motivated people. The results realized have served to turn interesting properties into productive operations.

Jan 1, 1988