Search Documents

Interstate 70 running into the mountains west of Denver, CO is the main access to the state?s numerous ski areas and other tourist attractions. As such, the highway is a vital part of Colorado?s economy. Due to the mountainous terrain in which it winds, I-70 is limited to two lanes in either direction. And, during the past few decades, the volume of traffic has increased to the point where motorists encounter major delays, particularly on Friday evenings and Saturday mornings heading west from Denver, and then again on Sunday evenings heading east. In the past, those delays occurred mostly during the ski season. However, many of the mountain towns have been successful in turning their resorts into year-round vacation destinations. A good move economically, but the pressure added to I-70 has caused even greater traffic delays, sometimes to the point where some Front Range residents avoid trips to the mountains.

Jan 1, 2013

By R. Pandey, G. Elie, E. Sarver

Respirable crystalline silica (RCS) is generally considered the most hazardous constituent of coal mine dust, and a new federal rule is expected to further limit exposures in U.S. mines. For regulatory purposes, RCS is monitored by collecting filter samples, which are analyzed for quartz (the predominant form of RCS in coal mines). The analysis is done using Fourier transform infrared spectroscopy (FTIR) in a centralized laboratory. To enable more timely results, National Institute for Occupational Safety and Health (NIOSH) mining researchers developed a directon- filter (DOF) FTIR analysis method and free FAST software that can be used in the field. For samples collected under specific conditions, FAST processes the FTIR spectral data to determine quartz mass. While the DOF FTIR method is not approved for regulatory RCS monitoring, it could be useful for engineering purposes, such as to evaluate mining parameters or new dust controls. This field study demonstrates how the method, including FAST, can be applied using low-cost, widely available sampling components. It further demonstrates how quartz percentage can be estimated in the field, by pairing a continuous personal dust monitor with a filter sampler.

Jun 1, 2025

By G. K. Wilson

This paper will discuss some of the more important aspects to be considered when selecting pumps for mill discharge, cyclone feed or other severe-duty applications Included will be the selection of the pump based on such factors as particle size, particle distribution, head, flow, temperature and pH Other specifics to be covered: The relationship of impeller speed, head and wear factors as they affect pump performance and wear life; the importance of selecting a pump whose performance curve best suits the application; and how the addition of service factors applied to the actual operating conditions can lead to severe operational problems such as premature wear, pump running out on curve, and exceeding horse power limitations.

Jan 1, 1996

"Foreword by Lisa SchlinkSuperintendent, operations, Freeport-McMoRan Inc.,Green Valley, AZ, USAThe sixth annual Student Poster Contest hosted by the Mineral & Metallurgical Processing Division of the Society for Mining, Metallurgy & Exploration was held during the 2015 SME Annual Conference and Expo in Denver, CO. The contest had another record-breaking attendance of 31 entries: 27 graduate and four undergraduate. The universities represented were: Colorado School of Mines, South Dakota School of Mines and Technology, University of Kentucky, University of Utah, Southern Illinois University Carbondale, University of Wyoming and West Virginia University.The competition began with an extended abstract review by a panel of judges selected from MPD members. At the SME Annual Conference, all students displayed their posters, highlighting their research. The students with the top abstracts from the graduate and undergraduate divisions presented their research at the MPD Student Poster Session Wednesday morning. The panel of judges then provided tallied scores for the abstract, poster and presentation to determine the winners of the 2015 Student Poster Contest. The first- and second-place winners of both the graduate and undergraduate divisions received $1,000 and $500 scholarships, respectively. The third through seventh places received $200 each, and all other entrants received $100 each and were invited to join the MPD Luncheon.In the undergraduate division, Annette Hein of the University of Wyoming received first place for her research on “Solvent Extraction of Europium from a Nitric Acid Solution.” Second place went to Jennifer Galvin of South Dakota School of Mines and Technology for her research titled “Solvent Extraction of Neodymium Using PC88A.”In the graduate division, Caelen Anderson of the Colorado School of Mines received first place for his research titled “Fundamentals of Rare-earth Flotation Surface Chemistry: Hydroxamate Adsorption on Bastnasite”. This is Caelen’s fourth year placing in the top finisher. Second place in the graduate division went to Seyed Hassan Amini of West Virginia University for his research on “Ultra Clean Coal Production for the Solar-cell Industry.”The 2015 Student Poster Contest was chaired by Lisa Schlink (Freeport- McMoRan Inc.) and Emily Sarver (Virginia Polytechnic Institute and State University). The panel of judges included Aaron Noble (West Virginia University), Nick Gow (FLSmidth), Ren Bryce (Freeport-McMoRan Inc.), David Perkins (Derrick Corp.), Jim Metsa (Weir Minerals) and Scott Shuey (Newmont).A special thank you is extended to the sponsors of the MPD Student Poster Contest, to all the students who participated and to the panel of judges. Watch for more information on the 2016 MPD Student Poster Contest to be published later this year on http://www.smenet.org/mpd/ and in the November issue of Minerals & Metallurgical Processing."

Jan 1, 2015

By Robert Walker

The win theme of this session is Unique Material Handing Systems. The theme was selected because of two major factors. 1. Accomplishments of unique character manage to attract interest regardless of their age. 2. There is much to be learned from pioneering efforts of the past as they are the stepping stones to technological development. Thus, 2-1/2 years after completion, the engineering feat of Oroville Dam still looms large let us take a close look at this project to see what made it unique. To begin with, it established a number of firsts: At 770 feet it was the highest earth fill dam in the world. At $121 million dollars, it was the largest ever United States construction project (Civil). At 80 million cubic yards it had the largest earth volume of any dam in the world. The extensive use of belt conveyors for this application had never before been tried. The use of a high capacity bucket wheel-excavator with shiftable belt conveyors had never before been utilized as a con¬tractor's tool. The principal of the "integral train" was applied most effectively whereby up to 220,000 tons of material-was transported daily some 14 miles. To achieve optimum economics a number of technical breakthroughs were necessary. The suppliers of major commercial components worked hand-in-hand with system engineers to develop new machinery necessary for the highly mobile characteristics of the systems, viz., single pulley drives delivering 2000 horsepower, 1000 horsepower right-angle shaft-mounted reducers, across the line starting of 1000 horsepower squirrel cage motors, 10 miles of steel chord conveyor belts with belt tensions up to 150,000 pounds, aircraft-type disc brakes, hydraulic take-ups, train loading at a rate of 25,000 tons per hour, automatic train indexing for rotary dumping at 10,000 tons per hour, roll-over car dumping without uncoupling cars, shifting 7500 ft. long conveyors up to 300 feet laterally without disassembly. These are some of the superlatives that have made the Oroville Dam project unique. The measure of its success is demonstrated by the results.

Jan 1, 1970

By D. C. Shumway

Recently, the health of the cement industry has been threatened by the impact of environmental regulations, over-zealous state and federal agencies and radical environmental groups. Unfortunately, cement plant operations tend to trigger every environmental regulation and program promulgated, plus several programs designed specifically for the cement industry. These environmental burdens come at a time when the cement marketplace has been impacted by imports resulting in a situation where it has been difficult to increase prices to offset these increased environmental liabilities. The competitive world market forces the cement industry to seek creative ways to reduce costs. With additional major environmental programs coming down the pipe, like the Federal Clean Air Act Amendments of 1980 and EPA regulation of cement kiln dust, the cement industry has attempted to try innovative supplements to cement manufacturing. The cement industry has found that using waste tires, biosolids and other solid wastes in the cement manufacturing process can reduce costs and plant emissions.

Jan 1, 1996

By S. Tuylu, D. Adiguzel, A. Bascetin

"Optimization techniques are successfully used in many different fields such as engineering, physics, economy, and politics in order to enhance the performance of the systems. In concrete technology, Aggregates are prepared by mixing the water and cement in proportional quantities. In order to obtain desired quality control parameters, the determination of the ingredients ratios is one of the important problems for the optimization. Additionally, in the quarries where the aggregate quality constantly changes, blending optimization must be made to obtain a sustainable aggregate quality. This study showed that linear programming, which is easy and which includes many aggregate properties, cannot be used in terms of some aggregate properties. Therefore techniques such as nonlinear programming or genetic algorithm must be used. INTRODUCTION Concrete is a used construction material and made by mixing the aggregate, cement, and water. The concrete properties are directly related to the properties of these materials in blending. The quantity of aggregates in concrete is approximately 70 percent of the concrete’s volume. Therefore, the most important material is aggregates. The extraction of aggregate materials in quarries is more problematic because of variable bedrock properties. Therefore, the quality of the materials changes and the characteristics of the concrete are also influenced directly. In terms of sustainable use of natural resources, produced aggregate materials which have different qualities should be used optimally (Adiguzel et al., 2014). Nowadays, in the solution of the blending optimization, various optimization techniques are being used such as linear programming, nonlinear programming, and genetic algorithm. In this study, blending optimization techniques especially used for concrete aggregates blending have been summarized, and the advantages and disadvantages of these techniques have been introduced. BLENDING PROBLEMS Blending is a frequently encountered problem in process-type manufacturing such as mining, refinery, food industry, chemical industry and metal industry (Sakalli 2010). Blending is a commonly used method in lots of practical solutions (Sarker and Newton 2008). Several optimization techniques are available for blending problems (Furman and Pardalos 2009). The most important issue is to blend with minimum cost. The blending problem is a special linear model which was developed to solve this problem. In blending optimization research, linear programming is a widely used method (Adiguzel et al. 2011; Bascetin and Adiguzel 2011)."

Jan 1, 2016

"INTRODUCTION While the United States coal mining uses prescriptive regulation under the Title 30 Code of Federal Regulation enforced by the Mine Safety and Health Administration (MSHA), Australia uses a risk based approach. Australian regulation is individual to each state. In Queensland, Australia this risk based approach to address principal hazards is underwritten by the Queensland Coal Mining Safety and Health Act of 1999 and the Coal Mining Safety and Health Regulation of 2001. Each Queensland Mine is required to have an overarching Health Safety and Environment Management System, of which Safety Management Plans are an element. “Safety Management plans (SMP’s) are intended to formalise the process by which mines address principal hazards and other related matters to ensure the safety of mine personnel.”7 THE QUEENSLAND CONTEXT In Queensland, the basic elements of a coal mine’s safety and health management system must provide for risk identification and assessment, hazard analysis, hazard management and control, and the reporting and recording of relevant safety and health information and data.5 (Part 2 Division 1 Section 6(a-d)) The initial guidance for writing Safety Management Plans comes from the Approved Standard for Mine Safety Management Plans and Guidance Note QGN09- Reviewing the Effectiveness of Safety and Health Management Systems. The Guidance Note and Approved Standard are supplemental to the Act and Regulation, and put in place to provide more clarity around the topic. The definitions in this section come from the Approved Standard and are included to provide context for those who may not be familiar with Australian or Queensland law and regulation. A hazard is defined as a source of potential harm or a situation with a potential to cause loss, while a principal hazard is a hazard with a potential to cause multiple fatalities. A risk is the chance of something happening that will have an impact upon objectives which is measured in terms of consequences and likelihoods. It is important to be able to make the distinction between a hazard and a risk. For instance, a lion is a hazard, while the risk associated with a lion is getting eaten. As defined by the Queensland Approved Standard for Mine Safety Management Plans, a Safety Management Plan (SMP) requires a systematic definition of all the actions necessary to ensure that mining operations are carried out safely. A SMP includes, but is not limited to organisational structures, planning, activities, responsibilities, practices, risk identification, audits and reviews.7 The goal of a SMP management plans is to mitigate the risks to bring them to an As Low As Reasonably Achievable (ALARA) level."

Jan 1, 2016

By H. B. Trinh, R. R. Srivastava

"Spent auto-catalyst is a potential secondary resource because of the higher concentration of valuable platinum group metals (PGMs) as compared to the primary ores. Despite the well-developed commercially tenable technologies, further researches are being carried out to extract the PGMs with high efficiency. It is however, critical in this context to reuse not only the PGMs but also other metals contained in the spent auto-catalyst particularly that of the cordierite substrate such as aluminum, magnesium and cerium oxide (CeO2). This is important in view of the fact that no recycling process has ever stressed upon the recovery of cordierite substrate and CeO2 since the main target metals are mostly the PGMs. In this study, a new hydrometallurgical approach has been proposed in order to recover the PGMs as well as cerium oxide and materials from the cordierite substrate by using sodium hydroxide roasting followed by sulfuric acid dissolution. Under the optimal conditions for roasting at above 600°C, and weight ratio of sample to NaOH of 1:1 for 60 min, the cordierite was converted to the soluble phases. Dissolution of the roasting products using H2SO4 solution (1M) at 25°C for 60 min enriched the PGMs and Cerium oxide contents in the residue. Subsequently, PGMs in solution after dissolution can be cemented using Al and Cerium oxide in residue can be recovered by hot digestion using concentrated H2SO4.. INTRODUCTION Auto-catalyst can significantly control the gaseous emission of automobiles, and has been considered as a potential secondary source of Platinum group metals (PGMs) after being decommissioned from the vehicles. The PGMs demand is continuously increasing to comply with the growing vehicle population and the tightening of emission standards all over the world; meanwhile the natural resources of these metals is facing the threat of depletion. Therefore, it is crucial to progressively substitute with an alternate resource to supply PGMs other than that of the primary ores. Nowadays, vehicular transportations worldwide are totally installed with the auto-catalysts. However, they should be replaced after reaching their service life. If there is no recycling of such resources, huge amount of valuable metals will be wasted. The quantity of PGMs that can be recovered from the spent auto-catalyst depends on the size of car, which averages to 1-2 grams for small cars and 12-15 grams for the big truck; this is significantly higher than that of the primary ores containing 2-10 grams PGMs per ton. Consequently, the recovery of PGMs from spent auto-catalyst becomes extremely favorable as compared to the primary resources due to higher concentration of PGMs, with much lower and simpler processing steps, and lesser pollution."

Jan 1, 2018

By Roland Froidevaux

The potential use of geostatistics for quantitative ore reserve reporting is shown using a simple gold case study as an example. The need of defining quantitative class limits is stressed, and a possible approach to this problem is suggested.

Jan 1, 1983

By J. J. Webb

At Kerr-McGee's Galatia Mine in southern Illinois, the need for safe and efficient longwall moves prompted a detailed planning effort. Galatia Mine operates two longwalls on separate coal seams with different geologic conditions. An overview of the longwall move planning as related to manpower training, roof control, ventilation, transportation, equipment recovery and setup will be discussed. The impressive safety record achieved during each of the longwall moves at Galatia Mine verifies that health and safety planning does play a major role.

Jan 1, 1994

By D. Carlson

At the Freeport Indonesia Grasberg Mine in Irian Jaya, Indonesia, a system of underground drainholes and surface drain wells have been designed and are currently under construction. The underground drainholes are located at elevations of approximately 9,600 feet and the surface drainwells located at elevations ranging between 12,500 and 13,000 feet. Together they will be used to drain the ground water contained within relatively incompetent rock. This drain system will allow for the successful dry mining of the open pit, and provide slope stability of the pit wall. The surface drain well network, when completed will allow for the draining of ground water to the Amole Drift where the underground drainholes are constructed.

Jan 1, 1998

By N. G. W. Cook

The conventional cyclic system of deep-level mining by drilling and blasting gives rise to an inadequate degree of stope sorting when mining thin reefs. This results in poor utilization of the capital facilities of a mine in the form of shafts, haulages, airways and associated equipment. Continuous and controlled removal of the thin gold-bearing portion of the reefs would permit better stope sorting and hence greater utilization of capital facilities. Results of experiments to develop hard rock cutting machines for mining are reported and the benefits which could be derived from their use are discussed.

Jan 1, 1969

By David Yankovich, Geoff Hughes, David Haug, Jon Kaneshiro

"In March 2013, the Sanitation Districts of Los Angeles County began final design of the Joint Water Pollution Control Plant (JWPCP) Effluent Outfall Tunnel project. The new, approximately 7-mile, 18-ft internal diameter tunnel will provide additional capacity and redundancy for the existing 8- and 12-foot diameter tunnels, which were built in 1937 and 1958, respectively. Connections to an existing, active 14-foot arch force main and four existing ocean outfalls ranging from 5- to 10-foot diameter are required. This paper will present geological features for the project, and details of the proposed post-tensioned tunnel liner and associated structures. INTRODUCTION The Sanitation Districts of Los Angeles County (Sanitation Districts) are 23 independent special districts serving approximately 5.3 million residents in Los Angeles County. Seventeen of the districts that furnish sewerage services to the metropolitan Los Angeles area are signatory to a Joint Outfall Agreement that provides for a regional, interconnected system of facilities known as the Joint Outfall System (JOS). The JOS service area is shown in Figure 1. The JOS serves an area that encompasses 73 cities as well as unincorporated territory and parts of the City of Los Angeles. The JOS provides wastewater collection, treatment, reuse, and disposal for residential, commercial, and industrial users, and it includes seven treatment plants, the largest of which is the JWPCP, located in the City of Carson. Currently, secondary treated effluent is conveyed through two 6-mile long parallel tunnels, 8- and 12-feet in diameter, from the JWPCP to a manifold structure located at Royal Palms Beach, near White Point on the Palos Verdes (PV) Peninsula, from which four seafloor outfalls extend offshore. The two main outfalls, 90- and 120-inches in diameter, extend approximately 1.5 miles offshore and discharge at a depth of approximately 200 feet below sea level. The other two outfalls, 60- and 72-inches in diameter, are used for additional capacity during heavy rain events and extend a shorter distance offshore and discharge at shallower depths. A schematic of the existing system with the proposed tunnel and structures is shown in Figure 2, and the proposed 18-ft diameter tunnel alignment is shown in Figure 3. Both existing tunnels and main outfalls are required to be in service at all times."

Jan 1, 2016

By Richmond Bennett

Airborne geochemistry became a reality with the advent of a high-sensitivity airborne gamma ray spectrometer with large volume NaI (TI) crystal detectors. Small variations in the concentration of potassium (as K40), thorium (as T1208) and uranium (as B1214) along the flight lines can be determined by measuring the gamma radiation with a sensitive airborne spectrometer. Small volume crystal spectrometers are useful only for detection of major surface uranium (Bi214) variations, but the large crystal volume system is an airborne geochemical exploration method capable of locating hydrothermal mineral deposits. Radioactivity as a guide to ore has been discussed in the literature by Damon (1950), Gross (1952) and others. The theoretical basis is that potassium, thorium, and uranium are concentrated in late stage solutions during magmatic crystallization. Thorium and uranium are concentrated in late stage liquids because their large atomic radius and high ionic charge prevent them from entering into the crystal lattice of common rock-forming minerals (Rankama and Sahama, 1950). Potassium, which has a large ionic radius and small charge, also can be concentrated in the high water content late stage fluids (Heier and Adams, 1964). A large proportion of uranium and thorium in rocks occurs around grain boundaries of the essential rock-forming minerals (Hurley, 1950). Uranium and thorium substitute for zirconium in zircon, a comparatively early forming mineral. However, most of the thorium and uranium is concentrated in residuals where they can be fractionated and incorporated into allanite, monazite, xenotime, and other minerals.

Jan 1, 1970

By G. R. Hart

The expected 1990 Clean Air legislation is providing electric utilities with a series of challenges and decisions as the utilities prepare strategies to comply with the resulting regulations. This paper addresses the strategy development of a coal-based utility --the legislation, the process used, the fuel issues, the options available, and the decisions to be made.

Jan 1, 1991

By Andy B. Wallace

Veins in the Pyramid district of northwestern Nevada occur along steep fractures in Oligocene and Miocene quartz latite tuffs. The vein mineralization is zoned from a central enargite-pyrite zone outward through a complex polymetallic intermediate zone and an outer zone of galena and pyrite. Wall rock alteration includes advanced argillic and sericitic envelopes along veins superimposed on district-wide propylitization. The ore distribution and alteration patterns were probably produced by an increase in pH, a decrease in sulfur fugacity, along with cooling of the migrating hydrothermal fluid.

Jan 1, 1978

By William N. Poundstone

Consolidation Coal Company, through the mining research division of Continental Oil Company, is now undertaking the installation of a full-scale hydraulic transportation system to carry coarse coal from the mine face to the preparation plant. The facility will include all elements of a fully integrated haulage system including face haulage for both longwall and continuous miner sections, multiple slurry feeds, hydraulic hoisting and 2.4 miles of overland slurry transport. This undertaking is a result of more than six years of extensive research and testing, some of which has been previously releasted to the literature. To provide a reference framework for system description, a brief history of recent coal mining technological developments will be discussed. Following World War II, mechanization resulted in mining machines that were bigger, faster, more powerful, and more reliable. These changes were essentially refinements in an established mining system. They made mining more efficient than before, but they did not change the system itself. By about the mid-1960's, it was apparent that further improvements in the extraction machinery would have a declining payoff, simply because .the worst bottlenecks were in other components of the mining system. A modern continuous miner cannot be run continuously because other operations underground cannot keep pace. In fact, most continuous miners today run at less than 20% of capacity. Consequently, in 1969 Consol and its parent company, Continental Oil, undertook a long-range R&D program to try to change the basic haulage system for the better. Most coal at present is removed from the mine by a hand-off system in which the coal is transferred from the continuous miner to a shuttle car, often with the aid of a separate loader; then from the shuttle car to a system of conveyor belts; and finally from the conveyors to rail cars. The system involves a large amount of moving equipment underground, many transfer points, and the everpresent chance of operational delays and safety hazards. By removing the haulage bottleneck, we believe we can speed up underground operations substantially; and perhaps more important, we could make it feasible to develop a whole new generation of mining equipment that is inherently safer. What we wanted was a truly flexible, continuous haulage system with inherent safety advantages. Ideally the system had to meet three major requirements: First, the coal had to enter the transport system at the face, and remain in that same system all the way to the preparation plant. Second, the system had to be flexible and extensible so that it could- follow the mining machine as it advances and retracts. And, third, the system must be inherently safer than current haulage technology.

Jan 1, 1977

By S. Jennings

The Red Dog massive sulfide deposit is located in the western Brooks Range of Alaska 100 miles north of the village of Kotzebue. It contains the largest zinc reserve in the world. Reserves were doubled in 1995 with the discovery of the Aqqaluk deposit and significantly increased in 1996, with the discovery of a deep zone of mineralization to the north. At present the global reserve and resource is 143 million tonnes of 16.1 % zinc and 4.3% lead. Red Dog is a silica + sulfide synsedimentary replacement deposit hosted in barite and black shale of the Mississippian Kuna Formation. Red Dog was thrust northward during the late Mesozoic Brookian orogeny. Understanding the setting of the deposit at the time of formation and its subsequent deformation history is critical to current exploration efforts and to future discoveries in the district.

Jan 1, 1998

By K. Lagnese, C. Robinson, S. Muddasani

"Mine water generated from underground coal mining operations contains both dissolved and particulate solids. Dissolved solids primarily consist of sodium, calcium, magnesium, potassium, chlorides and sulfates. When discharged to a receiving stream without treatment, these constituents create a potentially toxic environment for aquatic life. A case study is presented to discuss how a centralized treatment plant treats mine water from six locations to meet discharge limitations for chlorides. Located in West Virginia, this facility consistently achieves less than the NPDES permit limitation of 218 mg/L chlorides in the discharge while generating almost zero liquid waste. The dissolved solids concentration in the influent ranges between 5,000 and 10,000 mg/L, with chloride concentrations of 1,000 to 2,000 mg/L and sulfate concentrations of 2,000 to 6,000 mg/L. The mine water is treated using advanced treatment technology to produce clean water for discharge or reuse. The treatment process comprises aeration, softening, filtration, reverse osmosis, RO reject softening, evaporation, crystallization, final effluent remineralization and sludge dewatering. The solid waste generated in the treatment process is landfilled on site. The leachate is sent back to the facility’s thermal treatment process. Because no liquid waste leaves the property, this plant is termed a “Zero Liquid Waste” (ZLW) facility. INTRODUCTION The advanced water treatment system was built to meet a new 218 mg/l regulatory limitation imposed by the West Virginia Department of Environmental Protection for chlorides discharged to surface waters. The system is designed to treat a maximum flow of approximately 5 million gallons per day (795 m3/h) of mine water. The treatment process utilizes reverse osmosis (RO) membrane treatment to achieve the effluent criteria, and evaporation and crystallization technology to manage the RO concentrate from the water treatment process. As a result, the system produces clean water for discharge while generating zero liquid waste. The effluent water can be used for industrial purposes or discharged to a receiving stream. A Water Impact Index (WIIx) study indicated that discharge of this high-quality water into the Monongahela River watershed may improve the water quality for downstream water users. The waste produced in the treatment process, including softening sludge and salt, is disposed of in an on-site landfill."

Jan 1, 2015