Search Documents

By Raymond Sandiford, Taehyun Moon

"In 2012, Superstorm Sandy (Sandy) caused extensive flooding in many of the tunnels in New York City. The inundation resulted in two distinct stress changes to the tunnel structures. The first stress change was water pressure on the inside face of the tunnel lining. The second condition related to the change in buoyancy of the tunnels. In areas where the tunnels were supported on rock and an adjoining area supported on soft soil, overstress issues arose. Numerical analyses were performed to assess the structural impacts of the tunnel water inundation; especially stress changes due to internal pressure as well as changes resulting from the buoyancy effects. The paper will discuss the assessment process and its results; it will demonstrate that the change in internal pressure were of little consequence, however the change in buoyancy resulted in significant increases in bolt stresses. INTRODUCTION Superstorm Sandy caused tens of billions of dollars in damage in the NYC metropolitan area. It also caused significant disruption to the transportation system by flooding most of the under river tunnels servicing Manhattan from the outer boroughs and New Jersey. The rehabilitation of the tunnels was of paramount importance to the restoration of the NY and NJ economies. With this rapid restoration, it was essential to determine whether the flooding of these tunnels caused damage to tunnel structures. A series of analyses were undertaken to ascertain whether the change in the stress conditions and buoyancy of the tunnels, due to the flooding, was significant enough to cause damage or over-stressing of the tunnel components. The effects of this unforeseen loading condition was a concern to the agencies operating these tunnels and were thus analyzed to ascertain if there were any adverse impacts. This was a concern because the majority of under river tunnels in NYC was built earlier in the century and constructed using bolted cast-iron lining segments. The cast iron, although quite strong in compression, is much less so in tension. Also, after nearly a century of use, the bolts connecting these segments together have under gone varying degrees of corrosion. The stress changes in both the liner segments and the supporting bolts were estimated for conservative ground support conditions to provide confidence that the flooding had not caused permanent damage."

Jan 1, 2016

By W Frint

An area in Southwestern Wyoming is rapidly becoming the soda ash capitol of the world. Starting only 20 years ago from a unique deposit of trona, the out-put has rapidly increased until now about half of the soda ash produced in the United States comes from this area. Chemically, soda ash is sodium carbonate, a large tonnage, widely used alkali. The largest single industrial use is in glass manufacture, where 25 tons of soda ash are used in producing 100 tons of glass. Other big users are the detergent and chemical industries. The trona deposits in the Green River basin of Wyoming, were formed about 75 million years ago as part of a geologic period when an ancient lake alternately went through periods of being a large fresh water or smaller brine lake. Today these deposits lie from 800 to 3000 feet below the surface in a semi-arid, almost desert region just west of the Rocky Mountain Continental Divide at an elevation of 6200 feet. In this area there is a prevailing westerly breeze and almost every afternoon the velocity reaches very windy conditions. Rainfall is minimal, being only 6-8 inches of moisture per year with an evaporation rate exceeding 24-inches. Most of the moisture comes in winter snows or summer thunderstorms. Temperatures are low with below zero weather dur¬ing most of the winter and early morning frost is not uncommon during the summer months. There are many trona beds varying in thickness from a few inches up to 15 feet. The deposits now being mined vary from 8 to 10 feet in thickness. The ore is mined by driving tunnels either via conventional explosives or with continuous boring machines. It is transported to the shafts via conveyor belts

Jan 1, 1972

By D. C. Ridenour

The pressure system of ventilation with large diameter bore holes has been very effective in the ventilation of two gaseous mines, the Olga No. 1 and No. 2 Mines in McDowell County, West Virginia. The No. 4 Pocahontas Coal Seam on the Olga property lies 580 feet below the valleys. The seam is very gaseous as well as dry and dusty, which makes good ventilation all the more essential. Irregular and often extensive areas of the coal seam have been replaced with impervious shales and sandstones in "Fault" or "Want" areas. The replacement materials have sealed the methane in the coal seam and thus increased the quantity of gas that must be handled as mining is done. Often the No. 5 Pocahontas Seam comes down to meet the No. 4 Seam at the Faults and considerable methane is sometimes released from the upper seam. The factors mentioned, together with the irregular and unpredictable lateral shape' of the faults, result in long narrow stringers of coal that are very gaseous and difficult to mine. So far as the Olga Coal Company is concerned, the most effective ventilation under the conditions outlined has been the use of large diameter bore holes with a pressure ventilation system. The ventilation of a mine can be accomplished in two fundamental ways. The mine atmosphere maybe reduced below atmospheric pressure by an exhaust fan; or it may be raised above atmospheric pressure by a pressure fan. In either case, the coursing of the air is so planned as to have the haulage and traveling ways on intake air. While the majority of the coal mines in the United States, no doubt, use the exhaust system of ventilation, there are several advantages of the pressure system which are extremely beneficial.

Jan 1, 1960

By J. Stowe

While there has been continual improvement in the models for predicating deposition velocity and pipeline friction losses, the fundamental design philosophy for tailings pipelines has remained the same over the previous three or four decades: design the tailings pipeline to operate in turbulent flow without a deposit on the pipe invert for all expected process conditions. Recent improvements in the understanding of slurry pipeline flows allows for the design of pipelines operating with a deposit on the pipe invert, allowing the system to operate at moderate velocities for high flow rates, optimizing system energy requirements and maximizing pipeline wear life. Tailings pipelines are increasingly operated at higher solids concentrations where there is a greater likelihood the pipeline will operate in laminar flow due to the higher tailings slurry rheology. Historically, slurry pipelines have been operated in turbulent flow. We now know that laminar flow pipeline operation is possible as there are several operational laminar flow tailings pipelines. While our understanding of laminar flow slurry pipelines is not complete, recent research provides guidance on how to approach the design of these pipelines. New sensor technology has led to the development of an instrument that provides reliable indication of bed deposit height within a pipeline. This technology is particularly helpful in operating pipelines with a deposit and has application in better understanding the operation of laminar flow pipelines. Failure of tailings pipelines can result in consequent damage to surrounding structures and unacceptable spillage into the environment. Modern pipeline leak detection technology allows operators to better manage this risk by ensuring safe and reliable operation of tailings pipelines. This paper provides an overview of the each of the above advances in the design and operation of tailings pipelines. OPERATING TAILINGS PIPELINES WITH A DEPOSIT Tailings pipelines, and slurry pipelines in general, are typically designed to operate without a deposit on the pipeline invert. Meaning, the minimum operating velocity exceeds the turbulent deposition velocity. This approach has been adopted due to concerns regarding potential blockage of a pipeline operating with a deposit. Figure 1 shows a typical design duty envelope for a tailings delivery system as a function of solids throughput and solids concentration by mass. If the pipeline is designed to operate without a deposit at the lowest duty flow rate (4,480 m3/h), the operating velocity at the highest duty flow rate (6,590 m3/h) is about 1.5 times the deposition velocity. Considering that the pipeline wear and energy requirements are roughly proportional to the square of operating velocity, this results in an operationally inefficient system when the pipeline is operated close to the maximum design flow rate. Most systems tend to operate at maximum throughput after post-startup debottlenecking optimizations. Alternative Approach An alternate design approach is to ensure the pipeline operates without a deposit for the nominal flow rate and accept that a deposit will form when operating at lower flow rates. This results in the selection of a larger diameter pipeline, but there are significant benefits in terms of reduced energy requirements and lower pipeline wear.

Jan 1, 2019

By C. Einberger

Groundwater Monitoring is typically required by regulatory agencies at potentially hazardous landfills or surface impoundments. Agencies have often required an arbitrary number of wells with limited evaluation of the effectiveness of the network to detect a leak. A Monitoring Efficiency Model (MEMO) has been developed to improve the design and cost effectiveness of monitoring well networks. MEMO 15 an analytical model that simulates the migration of hypothetical contaminant plumes from a site and quantifies the efficiency of alternative well network designs in detecting the plumes. The computed monitoring efficiency provides a quantitative measure of the well network adequacy based on hydrogeologic considerations. The model was recently used to design the groundwater monitoring well network for a heap leach pad at the proposed Beartrack Project.

Jan 1, 1993

By M. G. Premo

The McKinley Mine is located in the northwest New Mexico, in McKinley County, approximately 25 miles from Gallup. The mine is operated by The Pittsburg & Midway Coal Mining Co. (P&M), a wholly owned subsidiary of the Chevron Corporation. P&M is headquartered in Englewood, Colorado. Since the McKinley Mine began operations in 1962 a total of 83,391,000 metric tons of coal have been sold through 1990. The 1991 production was approximately 5.000.000 metric tons. The mine operations are contained on a 109.000 square kilometers lease area of which 44.000 square kilometers are on the Navajo Nation. The present customer base consists of four utilities and one industrial account, all of which are located in Arizona. The utility customers are the Arizona Public Service Co. Cholla Station at Joseph City, The Salt River Project. Coronado Generating Station near Joseph City, and The Tucson Electric Company, Irvington Generating Station in Tucson. The industrial customer is the Stone Container Corporation, Snowflake Paper Mill.

Jan 1, 1992

By Phillip J. Maddex

During the last 10 years there have been many new developments in transport and handling equipment. Important technical and economic developments that can be used to reduce costs are; new terminal and materials handling concepts large river tows - 40,000 tons and 9000 hp towboats slurry loading and unloading of ocean vessels long distance pipelining of solids development of the shuttle train (unit train) large ocean barges ? 25,000+ tons ? pushed & towed 150,000 ton self-unloading super tankers - 300,000+ tons container shipping Some of these developments have been discussed at SME meetings in papers describing the transportation of minerals from new mines. But, only a few papers described improved transportation from older operations. Since transportation is a major part of the delivered cost for minerals, the economic benefits to be gained by putting new transportation developments to work are very substantial. Frequently good transportation planning and management makes the difference between a marginal ore body and a very profitable one.

Jan 1, 1972

By Terry L. Muldoon

On July 7, 1971, noise regulations for underground coal mines were implemented under provisions set forth in the Federal Coal Mine Health and Safety Act of 1969. These same regulations now also apply to coal mine surface facilities. In August 1971, in anticipation of these regulations, the Bureau of Mines, through the cooperation of the mine operators, conducted extensive noise surveys in three coal cleaning plants. The survey was conducted in an attempt to identify those occupations where exposures would exceed the proposed regulations.

Jan 1, 1972

By T. J. McKeon

Gravity separators such as spirals are commonly used in multistage cleaning and scavenging circuits to improve the quality and recovery of concentrates produced in the industrial minerals industry. Unfortunately, field surveys suggest that many industrial operations are poorly configured in terms of equipment layout. This shortcoming can often be attributed to a failure by engineers to make use of fundamental process engineering tools for circuit design. One of the most important of these is linear circuit analysis. This powerful tool makes it possible to mathematically compare the relative efficiency of circuit configurations in advance of experimental testing. This article provides a basic review of the linear circuit analysis concept and discusses some of the key insights it provides for the layout of multistage circuits. An industrial case study is provided to show the tremendous impact that this process engineering tool can have on the design of multistage spiral circuits in a heavy mineral wet plant.

Feb 1, 2012

By C. R. Kuhn

From 1968 to 1975, most work in surface modification of inorganic materials involved silane coupling agents. A silane coupling agent can be described simply as an oganosilicon chemical having a general formula RSi-X3 wherein the R group is attached to a silicon in a thermally and hydrolytically stable manner, and X is a hydrolyzable group usually having an alkoxy functionality. About 1975, Kenrich Petrochemicals brought into the market place titanate coupling agents. Titanate coupling agents usually consist of one alkoxy group and three functional groups attached to a central titanium atom. Zircoaluminates became available in about 1982. Zircoaluminate organometallic coupling agents, which vary principally in their respective organofunctionalities, arise from a basic technology in which two different types of organic ligands are selectively bound to a low-molecular weight zircoaluminate backbone.

Jan 1, 1995

By Jurgen Hahn

The paper reports on both, the design and decision making for the filters in a backfill plant in Europe as well as more then 10 years of operation and maintenance experience of the vacuum disc filters installed. It begins with the first step, the filter sizing based on a sample provided by the customer, followed by the commissioning of the filter units and reports on the development of the filter performance during the following 10 years of operation. Based on the physical properties of the sample and the process targets of the client for the backfill plant, the paper shows the logic steps taken in the laboratory to ensure the target moisture, determine the required filtration area and filter size as well as the selection of the ancillary units and the formulation of the performance guarantee. The paper discusses some issues with filter operation during the commissioning phase and the actions taken. Finally, the paper concludes by highlighting the gradual change over the more than 10 years of operation and how this change affected filter performance and operating costs.

Feb 1, 2024

By A. House

Newmont Mining Corporation owns and operates the Phoenix Mine near Battle Mountain, Nevada, USA. The existing milling facility has operated since 2006. Following the startup of the milling operation, and coupled with the upswing in the copper market, Newmont realized that Phoenix needed a process option to treat lowgrade transition and oxide copper ores. This meant that potentially revenue generating ore was being mined as waste. With no system in place to treat the transition and oxide copper, work began to determine the most feasible approach. After evaluating multiple options, the flow sheet was set for a run-of-mine (ROM) heap leach pad and solvent extraction/electrowinning plant (L-SX/EW). This paper will discuss the synergies and challenges of developing a copper L-SX/EW plant at the Phoenix copper-gold mill.

Jan 1, 2010

By Keith A. Heasley

The objective of this paper is to back-analyze the August 6th ,2007 collapse at the Crandall Canyon Mine in order to better understand the geometric and geo- mechanical factors which contributed to that collapse. In this work, the LaModel boundary-element program along with the best available information is used for the back- analysis. To initiate the analysis, a six step base model of the mining in he Main West area was developed. This base model included a step for each of the critical stages in the mining of this area. Next, calibrated values for the critical input parameters: rock mass stiffness, gob stiffness and coal strength, were developed and optimized based on the best available information. Finally, the model was used to simulate the final mining scenario. As a result of this back analysis , a number of conclusions can be made concerning the mine design and the August 6th collapse: 1) Overall, the area was primed for a massive pillar collapse because of the large area of equal size pillars, 2) The abutment stress from the active retreat sections and the adjacent longwall panels were significant contributors to the collapse, 3) From the modeling alone, it is not clear exactly what triggered the August collapse, although the active mining is a reasonable assumption.

Jan 1, 2012

By P. G. Semple

For the last four years, the Kilborn Group of Companies (Kilborn) has been involved in several major projects in the CIS. These projects include the Kumtor Project, the Kubaka Gold Project, the Kazgold Project, the Aginskoe Project and the Jerooy Project. These projects are all in various stages of detailed engineering and construction. In this paper, Kilborn will discuss our experience in the CIS and share some insight into project development in this geographic region.

Jan 1, 1996

By John W. Stevenson, Ted L. Sartain

Underground booster fan installations are currently employed in hundreds of coal mines throughout the world. Such installations, when properly designed and maintained, have proven to be safe and effective tools to provide desirable airflow volumes on sections or in areas of mines where the ventilation requirements exceed the capacity of the main fan system. In cases where an airshaft cannot be justified due to surface topography, depth of cover, or limited reserves a booster fan can serve the same purpose, be operational in a fraction of the time and at a substantially reduced cost. Booster fans are currently non-existent in U.S. coal mines. This is primarily due to lack of acceptance by the Mine Safety and Health Administration (MSHA), which has failed to acknowledge the merits of a booster fan system. Also, the absence of booster fan provisions in Part 75 of the federal regulations has led to the misconception that booster fans are legally prohibited in U.S. coal mines. In 1986, Jim Walter Resources, Inc. (JWR) developed and submitted to MSHA a plan to install and operate an underground booster fan at the No. 7 Mine. Detailed computer simulations were used to substantiate JWR1s position, that the booster fan could effectively provide the needed airflow on a developing section without adversely affecting ventilation in other areas of the mine. JWR also realized that numerous safeguards and operating procedures were essential for providing a safe system. Thus, safety features such as electrical interlocking, independent power supply, remote atmospheric monitoring, etc., were incorporated into the plan. This paper is a case-study that discusses JWR's proposed plan to install and operate an underground booster fan at No. 7 Mine. Unfortunately, MSHA's continued negative response has prevented implementation of the plan.

Jan 1, 1989

By R. L. Lewis

A simple method for estimating the steady-state water quality of a pit lake is presented. The steady-state concentration of a conservative chemical constituent in a pit lake is shown to be a simple function of inflow rate, evaporation rate, and inflow concentration. An analytical method is presented for estimating the equilibrium ground water inflow rate for use in water quality predictions. The time required to reach chemical steady-state is estimated using an iterative mass balance model. Mine operators should find the methodology useful for planning and screening-level regulatory applications where conservative estimates of pit lake water quality are desirable.

Jan 1, 1998

By T. A. Moss

The installation of equipment and structures at mines often requires the evaluation of unique loading and operating conditions. Consideration of these unusual features is required throughout design and construction and into operation. The necessity for employing sound civil, structural and mechanical engineering techniques to the design of structures and equipment is well understood. However, the influence of geotechnical factors on the overall behavior during construction and operation of these facilities is less appreciated. Mine operators routinely perform exploratory drilling for the purposes of defining ore deposits. These exploration activities can be extensive and often include provisions for assessment of subsurface conditions as they relate to the mining operation, i.e., requirements for ground support. All of these factors are important to the economics of the mine and are well justified. Surface facilities are provided to access and service the mine and they play an important role in the successful development and operation of a project. Headframes, hoist foundations and shaft collars, in particular, are examples of unique installations encountered at underground mine sites. The design and above surface behavior of these facilities can be analyzed with the usual fundamental engineering practices employed throughout the engineering professions. This requirement during the project development is understood and adopted. Unfortunately, near surface exploration for the purposes of assessing soil and rock conditions for foundations are often given a reduced priority and less consideration. This paper is aimed at providing an outline into the benefits and importance of performing such explorations and to provide a brief discussion of the merits of such an approach. References in the paper relate particularly to shaft headframes, hoists and shaft collars but the issues raised apply equally well to other installations of a similar nature, e.g. milling equipment.

Jan 1, 1992

By Nathan Painter, Kevin Andrews, Andrew Karpa

Groundwater flow in bedrock units is an important factor to be considered for most mining situations, both underground and open pit excavations. Characterization of the hydrogeologic system into which a mine will advance is an important factor for slope and entry stability, mine dewatering design, and potential environmental considerations including stream loss and water well damage. In addition, hydrogeologic characterization of bedrock is important for locating water wells and for groundwater contamination mitigation. Hydrogeologic characterization for a site begins with a desktop study and often evolves to include drilling, geologic logging, monitoring well installation, groundwater sampling, pump testing, and packer (Lugeon) testing. In addition to these methods of hydrogeologic data collection, downhole geophysical logging of exploration and monitoring well boreholes provides detailed information associated specifically with in-situ conditions of each hole. The basic suite of geophysical logging tools used for hydrogeologic characterization often includes Optical or Acoustic Televiewer (O/ATV), full wave sonic, gamma-density, fluid temperature, resistivity, specific conductance, and flowmeter. For many hydrogeologic settings, groundwater flow in the bedrock is dominated by discontinuities, or fractures, in the rock. O/ATV logging allows for determination of the frequency (clustering), orientation, and aperture width of in-situ fractures, while sonic logging allows for estimation of intact rock strength. Fluid temperature logging and flowmeter measurements provide insight with regard to potential groundwater inflow zones, and other tools provide information for geologic unit contacts. This paper outlines the process and benefits of using downhole geophysical logging for hydrogeologic characterization and provides generalized examples from industry experience.

By B. A. Slaker, T. Miller

"An underground limestone mine in eastern Ohio was experiencing significant floor heave and roof falls, attributed to high horizontal stresses. Areas of the mine showing floor heave were monitored with roof-to-floor extensometers and photogrammetry surveys, to determine the rate and magnitude of heave. Extensometer data were recorded hourly at four locations across adjacent entries while photogrammetry surveys of the floor were performed at the same locations every two to five weeks. A final survey was performed using an I-Site 8200 laser scanner. Following instrumentation, floor heave up to 10.1 cm (4 in) was measured by the extensometers, photogrammetric reconstructions, and laser scanner over a 6-month period. The extensometers were biased by the location where they were placed, failing to consistently capture the location and extent of floor heave and cracking. The photogrammetry surveys were not precise enough to capture small magnitude movements. Mining in the area was halted and within several months the floor movement and incidence of roof falls was significantly lessened. INTRODUCTION Limestone formations in the United States can be subject to relatively high horizontal stresses due to the presence of tectonic loading of the strata. Horizontal stresses have a documented history of causing stability issues in underground limestone mines. Kuhnhein and Ramer (2004) discussed the influence of horizontal stress on complex ground control interactions associated with limestone pillar design and mine layouts. Esterhuizen et al. (2008) documented roof damage observations associated with high horizontal stresses such has roof guttering, beam instability, oval-shaped falls, and failure propagations. There have also been a number of documented case histories of horizontal stress causing unexpected roof and pillar failures at shallow depths (Stacey and Yathavan, 2003). To the knowledge of the authors, there has only been one well-documented case of floor failure causing stability issues in an underground limestone mine. Murphy et al. (2015) documented the role that a weak, moisture-sensitive floor had in the development of a massive roof collapse. For this paper, the study site neighbored, and was in the same general geology of, the site in Murphy et al. (2015). However, the weak, moisture-sensitive floor was not present for the current study. The current study site has experienced significant floor instabilities caused by high horizontal stresses. The instability area was monitored using two different methods to determine if the floor failure would eventually propagate into roof or pillar failure. The objective of this paper is to analyze displacement monitoring measurements from string potentiometers and remote sensing techniques in an area experiencing active movement. Based on the measurement trends and observed damage from inside of the mine, the presumed failure process will be discussed."

Jan 1, 2017

By Taghi Sherizadeh, Paul Brooks, Dogukan Guner, Samuel Nowak

Large excavations are well known to result in rock mass deformations which can present challenging situations for mine personnel. Most of the currently available ground movement monitoring devices fail to adequately provide mine operators with highly accurate and meaningful insights into rock mass deformation or displacement. The use of distributed fiber optic sensors (DFOS) in industries such as oil and gas and civil engineering has shown the potential of these sensors to deliver real-time, highly accurate, and long-range distributed strain measurements with great success. However, the use of these sensors in underground mining is limited to a few case studies.