Search Documents

By A. Jolly, A. R. Kumar, T. Novak

"Coal dust in an underground mining environment has always been a health and safety issue, especially with longwall faces. Efforts to integrate a flooded bed scrubber within a longwall shearer are underway at the University of Kentucky (UK) in order to reduce worker exposure. Small scale physical modeling, along with numerical modeling and full-scale experimentation, are engineering tools being used by the authors for simulating operating conditions underground. Recent advances in affordable 3D printers offer a means for fabricating accurate, scale models for obtaining timely insights prior to building large, expensive test setups. Comparing scale-model results with those of numerical modeling, such as computational fluid dynamics (CFD), lends guidance and confidence in a proposed design. This paper discusses the small scale physical modeling of a longwall shearer with an incorporated flooded-bed dust scrubber in its operating environment. A tracer gas was used in the model in lieu of dust to measure dust-capture efficiency. Results obtained from the physical model are presented and compared with those of CFD model. The small scale model and the CFD results demonstrate good agreement. Dust capture results show the usefulness of the approach in advance of actual design implementation. INTRODUCTION Dust generation is an undesirable, but innate, byproduct of all mining processes. It is particularly problematic in underground coal mining, where coal dust poses potential hazards from two fronts – health and safety. Coal workers’ pneumoconiosis (CWP), commonly referred to as black lung, is a chronic lung disease that results from the long-term overexposure to respirable coal dust. Although the prevalence of CWP has steadily and significantly declined over the three decades following the Federal Coal Mine Health and Safety Act of 1969, a study by the National Institute for Occupational Safety and Health (NIOSH, 2008) indicates that significant health hazards associated with respirable dust still exist within the coal mining industry. In addition to being a health hazard, coal dust can also create a potentially catastrophic safety hazard. Dust that is not captured or removed at its source is suspended and transported throughout a mine by the ventilation airstream. This float dust is subsequently deposited on all mine surfaces along its travel path. Without adequate application of rock dust to these surfaces, forces from a localized methane ignition can reintroduce settled coal dust into the airstream creating an explosive mixture. Therefore, capturing and removing coal dust at its source mitigates the probability of two major hazards that continue to plague the mining industry."

Jan 1, 2016

By S. K. Singh

"Feather edging"-a major source of injury and fatal accidents in Australia, South Africa and USA, refers to a phenomenon where the roof, at the goaf edge, falls as a thin wafer of rock often suddenly, over-riding conventional timber breakerlines. It may run down and affect adversely a working bord at distances of 15 metres or more from the goaf edge. Feather edging typically occurs in relatively massive, strong roof strata such as sandstone or conglomerate. This paper presents the results of a mine trial where a concentrated row of fully grouted bolts were able to resist the feather edging in the first comprehensive, monitored trial in an Australian pillar ('total') extraction coal mine.

Jan 1, 1999

By Michael Schultz, Gregory Sanders

The City of New Haven is planning to construct the Downtown Storm Sewer Infrastructure Improvement project to mitigate on-going stormwater flooding in the Long Wharf District. The proposed project includes a 685 cubic feet per second (cfs) stormwater pump station and a 3,200 linear feet (975 meter) long tunnel segment with an internal diameter of 120-inches (3.05 meters). This paper presents the aspects of the final design and the use of the cloud-based data management software to make better data-informed decisions. The software was used to create a spatially aware database of the subsurface conditions, as well as improve visualization and analysis of the soil properties.

Dec 1, 2022

By John W. Robertson, Edwin A. Zink, Gerald P. Zink, John E. Wolgamott

Equipment which will reliably produce high velocity water jets for use in rock excavation is now available. This report reviews some cases where water jets were used in excavating low to medium strength sandstone in Colorado and Utah. The primary discussion is of water jet assisted rotary drilling for blast and bolt holes in tunnels, shafts, and chambers. The subjects include drilling performance, effects on work environment, safety, and controlled blasting results. Information is also presented concerning trench excavation utilizing water jets.

Jan 1, 1983

By Sidney M. Cohen

This paper describes an economical method of upgrading a clay deposit using conventional separation processes into a suitable cement plant feed. The natural size difference of clay and silica in the clay deposit is utilized in the dry air classification device. A case study in which the raw material from a clay deposit is converted into a portland cement plant feed is presented.

Jan 1, 1983

By Q. X. Yun, S. H. Liu

This paper provides a new approach to determine the opening layout in underground mining methods by means of genetic programming. Based on a set of random combination of openings, the layout of openings will gradually improve with the help of genetic operations, including reproduction, crossover, mutation and fitness calculation. The optimal solution will finally emerge according to Darwinian principle: "the survival of the fittest ".

Jan 1, 2002

By Jianguo Hao, Qingbiao Zhao, Bingnan Hu, Shimin Fan

The paper makes a systematic analysis of interaction between backfill and pillar in coal mining. It compares the difference of pillar strength with backfill and without backfill. It is proved that there are the obvious improvements in pillar strength and the decrease in subsidence. It discusses the subsidence effects of different extraction ratio, different backfill ratio, and different elastic modulus ratio in details. The paper analyses the sensitivity by orthogonal test method. At last, author proposes some suggestion to increase pillar strength, to reduce subsidence, and to guide engineering practices.

Jan 1, 2001

By Corneille S. Ek

Flotation of several copper and lead-zinc ores has been carried out with mercaptobenzothiazole (MBT) as promoter. The results of laboratgory batch flotation tests have been compared with those obtained when using more common collectors like xanthates or dithiophosphates. It generally appears that MBT is an effective collector of all the sulfides, including pyrite, but that high selectivity is rather difficult to attain, except for gangue drop-out. Some kinetic tests have been performed to check the froth production rate by MBT as compared to other collectors.

Jan 1, 1995

By Jay A. Bowden

In April of 1990, Homestake Mining Company began a 5,100 m (16,700 ft.) exploration drift from the Homestake Mine in Lead, South Dakota. The drift starts from the mine's 6800 level, nearly 2,100 m below the surface, and extends north to further explore occurrences of gold discovered by surface drilling. Access to the North Drift for men and materials and for disposal of waste rock is limited to the Homestake Mine's #6 Winze, which serves as the major production shaft for the deep levels of the mine. This paper will discuss the successes and challenges encountered while managing a tunneling project 2,100 m below the surface and from an active mine.

Jan 1, 1993

By Sarah Vest, Richard Sherman, Leo Martin

In 1988 a major exploration program was undertaken to determine the characteristics of the rock and soil for a 7.6 m diameter sea outfall tunnel beneath Boston Harbor out into Massachusetts Bay. The diffuser discharge location had been mandated by the EPA to a 10 sq. km area of seafloor connected to the proposed Deer Island Treatment Facility by a 14.5 km tunnel corridor. Geophysical surveys, deep rock borings, and laboratory testing, provided the information for the conceptual design. The program identified the range in material types and parameters to prove feasibility of a TBM driven tunnel and to locate the optimum alignment and depth.

Jan 1, 1991

By S. Hartwig, K. Wohiwend, J. Forsberg, G. Bergling

New, larger cutters requiring higher operating loads and thus increased cutterhead thrust, higher cut¬terhead speeds and more pronounced demands of maintaining high penetration rates also in mixed ground, constantly augment the loads on TBM main bearings. At the same time, the demand of a single TBM model covering a wide diameter range limits the available space for the main bearing at the smaller end. Innovative concepts and advanced methods of calculating bearing loads and lifetimes are needed to meet the demands which TBM suppliers and their customers face. This paper reviews different design approaches and covers the influence of lubrication on bearing life and condition monitoring as well.

Jan 1, 1995

By R. K. Davey

Before the introduction of computerized procedures, mineralization modeling (compilation of level maps), ultimate pit studies, ore reserve compilations, and long-range mine planning all were performed manually. In fact, much of the basis for today's computer programs was derived from manual procedures and actual experience of mining engineers and geologists.

Jan 1, 1979

By Terence G. McCusker

Precast concrete segmental tunnel linings have been used since at least 1903. More serious attention was devoted to them in England during the World War II steel shortage and they have become increasingly common since that time. They are now coming into common use in the United States, especially as primary linings for soft ground tunnels and for rock tunnels in poor ground, although they have also been used as final lining, especially in rock tunnels. The developmental logic, design considerations, and current practices are examined. Particular attention is given to unbolted linings, with and without secondary linings. Probable future developments are considered.

Jan 1, 1989

By David Oliveira

"INTRODUCTIONOne of the key drivers for the selection of a mechanized tunneling method in good quality rock masses is a good excavation advance rate. In order to achieve satisfactory advance rates, a good geotechnical performance of the rock grippers in main beam open tunnel boring machines (TBM) is required, besides other factors related to ground support and the performance of the cutter head.One well known potential issue of main beam gripper TBM is associated with the bearing capacity of the tunnel side walls while crossing fault zones or poor rock masses in general. Such a mechanism is similar to that of footings on rock and perhaps the most common problem associated with gripper performance. Depending on the quality of the rock, the rock under the gripper contact may experience significant damage and crushing (Figure 1), eventually affecting the TBM advance rate due to a lack of tunnel wall reaction/support. Such a mechanism is primarily dependent on rock quality, applied loads and gripper size.In the case of large diameter TBMs (e.g., D > 12 m), a second potential failure mechanism may arise associated with the loss of confinement within a rock pillar between twin tunnels, even in good quality rock but particularly in bedded sedimentary strata. Punching of the rock pillar may develop due to excessive shear along bedding partings and sub-vertical joints (Figure 2), particularly under a low stress environment. As a result, this mechanism is dependent on both the rock pillar width between twin tunnels and stress conditions around the tunnels, in addition to the previous factors described for the first failure mechanism."

Jan 1, 2016

By D. G. Ball

Other than being used to convey fill material for the gob stowage or building of ribside packs on advancing longwell faces, pneumatic conveying has not been used for the transport of materials on a large scale in mining operations. The technique is extensively used in the wood products industry for conveying wood chips, limestone and other ingredients for the manufacture of paper, for the transfer from railcars, barges or ships to silos or stockpiles and further transfer into the pulp mills. This method of material transfer has the distinct advantage of transporting suitable material over horizontal and vertical distances within the same system. In considering material associated with mining, this includes, ore, coal and rock up to 4 inch cubed size, throughputs of 200 tons per hour over horizontal distances of 3000 feet or vertical lifts of 2000 feet. In recent years tests have been carried out to determine the physical and economic limitations of pneumatic hoisting, the results of which have led to the installation of two fully productive coal hoisting systems at mines of the National Coal Board in Great Britain. The equipment used for the pneumatic hoisting of coal or waste rock is described in this paper, together with a brief history of the tests which led up to the installation of the two hoisting systems in Great Britain.

Jan 1, 1977

By Colin Connors

Cemented rockfill is a key component in the success of underground mining at the Jerritt Canyon Joint Venture. The Murray and SSX mines are characterized by relatively poor rock mass quality, and the goal of complete mining recovery makes maintaining a high quality backfill product vital to the safety and efficiency of the mining operations. A large portion of the ore production from the Murray mine originates from drifting under backfill. Modelling studies performed to investigate induced loading of the backfill were used to develop engineering specifications for the backfill material. Operations history has shown an almost 100 percent stability of the backfill when mining is carried out beneath it. The volume of backfill required each year (approximately 300,000 tons) and the required cement content have a significant impact on the total mining costs. The potential for cost savings associated with higher replacement of cement with Type "C" fly ash and the implementation of a backfill strength management strategy were therefore evaluated.

Jan 1, 2001

By Edward M. Dowey

This paper presents the excavation of the Roosevelt Island Valve Chamber, the final of three chambers in Stage One of New York City's Third Water Tunnel. The valve chamber and passageways 13 379.7 cu m (17 500 cu yd) are drilled and blasted. The rock is stabilized by grouted rock anchors. The 6.1 m (20 ft) diameter shaft is drilled, blasted, rock bolted and wire meshed for a depth of 70.7 m (232 ft). Then shaft excavation proceeds with immediate concrete lining for another 120.7 m (396 ft). Two 6.1m (20 ft) diameter manifolds are excavated using heading and bench. The raise drilling of eight 3.7 m (12 ft) diameter laterals occurs during lower shaft sinking.

Jan 1, 1987

By R. D. Hendry, R. A. Pearce, Allyn J. Steward, Dennis C. Martin

This paper outlines the geotechnical exploration and design approach utilized for the Km 80 and Km 86 Tunnels on the British Columbia Railway Tumbler Ridge Branchline. Information from surface mapping, trenching and diamond drilling was used to prepare a rational support design using accepted rock mass classification systems. Four possible support types were developed and used as a basis for preparing a cost estimate and contract documents for the tunnels. A unit price contract was selected to provide flexibility and to enable rational selection of support based on actual ground conditions encountered during excavation. Although ground conditions along the tunnels are variable, the general geology and quantities of support installed were consistent with those estimated from the geotechnical investigation and design.

Jan 1, 1985

By Timothy J. Napier-Munn, David M. Weedon

A model of mineral liberation was developed using back calculation techniques to determine breakage/liberation parameters in a similar manner to the way breakage parameters are determined in the Population Balance Model (PBM). Comminution and liberation data was collected from grinding mills operating at Pasminco lead/zinc mine Broken Hill, and Mt. Isa Mines copper concentrator, Mt Isa, Australia. Laboratory scale single particle breakage tests on ore samples from these sites were undertaken using a twin pendulum breakage device. Break- age/liberation parameters were then determined for several mills using back calculation techniques. The liberation/breakage parameters were then used to simulate mill liberation performance under varying conditions.

Jan 1, 1996

By Leif A. Nordell, Philip E. Freeland

A paper discussing specification, methods, situations and results encountered in underground phase construction of the Rocky Mountain Pumped Storage Project near Rome, Georgia. The scope of work included excavation, rockbolt/shotcrete/wire mesh primary support and cast-in-place concrete lining of the (1) 216 m, top flared shaft, connecting 1.57 radian elbow, and 590 m tunnel to a 10.67 m finished diameter; (2) complex double bifurcation section; (3) excavation, support, installation and backfill concrete for three parallel, 135 m steel penstocks of 5.79 m finished diameter; (4) construction of a 43 m diameter reinforced concrete intake/discharge structure atop the shaft.

Jan 1, 1985