Search Documents

By R. A. Lowe

Smectite is a common impurity in the kaolins of Georgia. This impurity is harmful to the low-shear rheology of kaolin slurries in concentrations as low as a few weight percent. The deleterious effect of smectite on the low-shear rheology is due to the swelling of the mineral. Montmorillonite containing clays were treated to precipitate a compact brucite layer {Mg(OH)2} in the interlayer region of the expandable layer silicate mineral. This treatment forms a hydroxy-Mg-montmorillonite with characteristics similar to chlorite. This treatment effectively reduces the swelling capacity of the mineral and improves the rheological properties of kaolin slurries contaminated with smectite impurities.

Jan 1, 1999

By R. Schuerch, G. Anagnostou, R. Poggiati

"The paper presents dimensionless design diagrams for estimating the stand-up time of a tunnel face in saturated ground of medium-low permeability. The diagrams cover a wide range of ground parameters and apply to shallow tunnels (overburden less than two diameters). As the time-dependency of the face stability in water-bearing ground is associated with the consolidation process in the soil ahead of the tunnel face, the stand-up time is determined by means of hydraulic-mechanical coupled spatial stress analyses. The results presented are important for tunnel engineering practice, e.g. when estimating the feasibility of atmospheric interventions in the working chamber of a closed shield. INTRODUCTION The response of water-bearing medium-low permeability ground to tunnel excavation is time dependent. The time-dependency is due to a transient seepage flow process that is triggered by the excavation and develops slowly over the course of time. Experience shows that the short-term behavior the ground is more favorable than the long-term one: the deformations increase with time; the tunnel face may be stable initially and fail only after some time. The time over which the tunnel face remains stable is called the stand-up time. This paper investigates the time dependency of the tunnel face stability assuming that all time effects are due to consolidation rather than creep. This assumption is reasonable for shallow tunnels crossing water-bearing soils. In the problem under analysis, the unsupported tunnel face remains stable under the undrained conditions prevailing after excavation, but collapses before reaching the drained conditions prevailing at a steady state. The assessment of the stand-up time is important from an economical point of view for both mechanized and conventional tunneling through weak water-bearing ground, as a long stand-up time removes the need for face support or ground improvement works during standstills, thus saving time and money, while short stand-up times require hyperbaric interventions or the implementation of costly and time-consuming auxiliary measures."

Jan 1, 2016

By Gerald L. Dollinger, Joseph A. Roby, David Krauter, Kenneth Deering

Three high performance TBM's equipped with large diameter (483mm) disc cutters are currently operating in Norway. This paper summarizes the design philosophy, field performance and ongoing technical development of these cutters. Included are discussions of the early problems encountered with their usage and the solutions to these problems that have been developed. Also included are discussions of the penetration rates and cutter usages observed. From this data it is concluded that high performance TBM's with large diameter cutters can produce significant improvements in both overall performance and in cutter costs under hard rock conditions.

Jan 1, 1991

By Richard A. Thomas, Liming Yuan, James H. Rowland III, DAVOOD BAHRAMI

To reduce the number of injuries resulting from fires on mobile, diesel-powered mine equipment, it is crucial to promptly suppress a fire once it is detected. The focus of this research was to determine the effectiveness of fire suppression agents. Large-scale tests were conducted using five different fire suppression systems based on: dry chemical, wet chemical, dual agent (dry and wet chemical), carbon dioxide, and water mist. Suppression nozzles were placed around the diesel engine where diesel fuel, engine motor oil, and hydraulic circulating oil spray fires were ignited. The results of this study can help mining companies and manufacturers by providing scientifically based data on the capabilities of the different fire suppression systems.

Feb 1, 2024

By B. Derin

In this study, the Reddy-Blander model was applied to predict the sulfide capacity (CS) values of FeOx-CaO-SiO2, FeOx-MnOx-SiO2 and FeO-MgO-SiO2 ternary slags, which were experimentally studied in the literature within the temperatures between 1,673 and 1,923 K. As expected, sulfide capacity values of the slags increased with increasing temperature and decreased with increasing acidic content. The model was found to be in agree-ment for all slag systems at the temperature range of 1,773-1,923 K. However, a disagreement occurred when the basic content was relatively high, at 1,673 K for FeOx-CaO-SiO2 and FeO-MnOx-SiO2 slags. The effect on the CS of high amounts of Fe+3 and Mn+3 in the slags is discussed.

Jan 1, 2011

By M. A. D. Azevedo

The effect of pulping reagents on the flotation de-inking of laser printed wastepaper was investigated with regard to the removal efficiency of toner and mineral filler particles for different pH values. These results show that caustic pulping causes the toner to be released from the fibers at larger particles sizes. On the other hand, acid pulping not only causes the toner to be released at smaller particles sizes but also increases the concurrent flotation removal of mineral filler particles. It was experimentally observed that the froth generation and stability during flotation were improved for acidic pH values.

Jan 1, 1997

By R. Sandrik

Northwestern Resources Co. (NWR) was established in 1972 as a wholly-owned subsidiary of Western Energy Company of Butte, Montana, to acquire, explore, develop, and produce energy resources outside the state of Montana. Western Energy is a coal mining company with successful operations in Montana and Wyoming. In 1974, NWR acquired its first lignite lease in Texas. NWR eventually acquired a large leasehold in central Texas, which was identified as having a high potential for future production. In 1979. NWR contracted to supply lignite to Utility Fuels, Inc. (UFI), a fuel affiliate of Houston Lighting and Power Company (HL&P). This project, together with leases held by UFI, became the Jewett Mine. Lignite from the Jewett Mine is used as fuel at the adjacent HL&P Limestone Electric Generating Station, at an annual rate of approximately 7.3 Gkg (eight (8) million tons) per year.

Jan 1, 1991

Optimal gold recoveries largely depend on efficient liberation of the gold or gold-bearing minerals as well as on maximum access for the lixiviant. Thus, crushing and grinding may become the most costly part of gold ore processing. It may, in fact, represent 50% to 70% of a plant's operating costs (Michaelis, 1989). The increasing significance of refractory gold will require even more cost-efficient comminution of ultrafine sulfides and/or native gold. Transitional ore zones with semi refractory gold may respond to direct leaching if better particle fracturing is being achieved (Baum, 1991, 1993a). Many oxide ores have been left in the ground because they were unsuitable for heap leaching since conventional comminution could not facilitate economic gold extraction. Also, the costs of conventional bal1 mill operations did not permit the recovery of gold from many ultrafine, low-grade refractory ores. As shown by Marsden et al. (1993), the trend to treat ores with progressively lower grades will involve power-and leach-efficient grinding applications. Our current laboratory work shows that high-pressure grinding roll (HPGR) Polycom grinding may enable many mining companies to add large amounts of these "non-leachable" ores to their current heap or mill leach feeds. This finding may dramatically change the economics of many oxide gold ore operations and may add significant reserves to ores amenable to direct cyanidation.

Jan 1, 1994

By D. O. Murchu

Outokumpu Tara Mines located near Dublin, Ireland is Europe's largest producer of lead and zinc concentrates. To reduce dewatering costs and to improve environmental and working conditions, elimination of the lead concentrate thermal dryer was required. This paper describes the development and implementation of the pressure ceramic technology at Tara to replace a conventional vacuum filter/oil-fired dryer system. In 1996 the pressure ceramic filter dewatered 66,600tonnes of lead concentrate, producing a cake at 6 % moisture. Substantial operating cost savings have been realized. Commissioning of a second pressure ceramic filter to handle over 300,000 tonnes/year of zinc concentrates is scheduled for the first quarter of 1997.

Jan 1, 1997

By Vittorio Manassero, Antonello de Risi, Filippo Cavuoto

"This paper deals with an innovative mechanized method to bore and simultaneously line circular shafts, adopted in the Naples Metro project for the installation of 10 vertical shafts for ventilation purposes. With this method, excavation of shafts is carried out under a positive head of stabilizing fluid by a milling machine, temporarily set at the bottom of a permanent lining made of precast reinforced concrete segment rings. The debris is evacuated by inverse fluid circulation. The shafts in Naples are 4.5 m I.D., from 34 to 44 m deep and they are all located downtown in a highly urbanized area. They were bored and installed into volcanic soils under a hydrostatic head of up to 30 m. Displacements and groundwater level were constantly monitored to keep control of the effects on the surrounding buildings and utilities. INTRODUCTIONThe extension of Metro Line 1 in Naples (Italy) from the previous terminal of Piazza Dante to Piazza Garibaldi is also called the “low stretch”. Most of it runs along the coastline, encompassing the historical city center, the Greek-Roman Neapolis. The Metro Line crosses under densely urbanized areas for the whole way (Figure 1). It runs beneath Via Toledo, which follows the layout of the ancient Aragonese walls. The first station (Toledo) is located halfway along this street. Then, after a wide bend, the line reaches Piazza Municipio, where the second station is located. From there, the line moves along the axis of Via Depretis and Corso Umberto I, where the stations Università and Duomo are situated. The fifth station is in Piazza Garibaldi and the end of the stretch is located at the Naples Business Center. The twin single track tunnels were bored into volcanic tuff by TBM. This design choice simplified by far the construction of the tunnels and reduced to practically zero the interactions between tunnelling and surface buildings and utilities. Nevertheless, this choice entailed that the line had to be located at depths to the order of 35-45m below ground level and 30-35m below the water table. At each tunnel segment between stations, a pair of ventilation chambers were constructed (10 in total). Each ventilation chamber is connected to one TBM tunnel by a vertical shaft and a horizontal drift at the base of the shaft. The shafts, in addition to tunnel ventilation, provide a safety access/escape."

Jan 1, 2016

The strength of anchorage of various types of roof bolts in permafrost depends on the types of rock in which they are installed. Variation in the mine thermal regime results in weakening of the roof and walls, and at times total loss of ice cement bonds takes place in the surrounding rockmass. In mines with positive ventilation air temperature, the wedge or expansion types of bolts may become weakened due to the transfer of heat into the anchorage through the metal rod and subsequent thawing of rocks. Effective operation and evaluation of roof bolt systems for mine workings in permafrost require predictions of the dynamics of wall thawing by warm ventilation air. This paper presents an analysis of the temperature distribution in the frozen host ground surrounding roof bolts, the area of interest being the vicinity of the anchors for point anchored bolt and the entire length for split set bolt

Jan 1, 1994

By Luisa Alfieri, Giorgio Fantauzzi, Sergio Notarianni, Spencer Cavagnet, Alessandro Damiani

"The new tunnels of the Copenhagen ""Cityringen"" will be excavated, at Kongens Nytorv square, crossing over the existing M1 and M2 metro lines. After the crossing, the tunnels will underpass the historical building of the Magasin du Nord and adjacent masonry buildings, with a minimum tunnel cover of about 4.5 m. The tunnels have an internal diameter of 4.9m and are being excavated through earth pressure balanced Tunnel Boring Machines in mixed face.The Magasin du Nord estate is characterized by a very complex structure, with different blocks built in different times. An assessment of the condition of the building and its sensitivity to tunnellinginduced ground movements has been conducted through a fully coupled soil-structure interaction analysis; based on the results of this analysis, mitigation measures have been designed.INTRODUCTIONThe Copenhagen Metro Cityringen is expected to be running in July 2019 and will consist of two single tracks in a twin tunnels, each approximately 16 km in length, for transporting up to 243,000 passengers on an average work day. The Cityringen includes 17 underground stations with island platforms, 4 crossover facilities and 3 construction and ventilation shafts. The tunnels is being excavated using earth pressure balanced Tunnel Boring Machines and have an internal diameter of 4.90 m.The intersection with the existing M1 and M2 metro-line will take place at Kongens Nytorv and at Frederiksberg. According to the design alignment, in Kongens Nytorv the new tunnels will pass over the existing M1 and M2 ones; as a result of this, the tunnels will underpass the historical building of the Magasin du Nord and the adjacent masonry building hosting a Mc Donald’s with a minimum cover of about 4.5m.In the framework of Risk Assessment for sensitive buildings, the effects of tunneling-induced ground movements on the Estates ØS0437 (McDonald’s building), ØS0428 (Magasin du Nord) and ØS0004 (Hviids Vinstue) were evaluated. To achieve this goal a fully coupled soil-structure interaction has been considered and the entire excavation process has been reproduced in a 3D model where the abovementioned buildings have been modeled. In this way, a risk assessment analysis was performed evaluating directly the effects of the excavation in terms of settlements and variations of the internal forces as far as the excavation process proceeds. In figure 1, a picture of the construction of Kongens Nytorv station, with Magasin du Nord and Mc Donald’s building on the background, is presented."

Jan 1, 2016

By Kim McKnight

Dupont has successfully incorporated a Floatex Density Separator into its wet-gravity operations for the recovery of zircon from titanium tailings. Results indicate that the Floatex achieved a zircon recovery of approximately 95% while rejecting similar amounts of quartz and other gangue minerals. Additionally, a unit capacity approaching 16 tonnes/hr/m2 was achieved. Results also show that the alumino-silicates can be separated into other product streams that will further improve process economics and minimize waste material. The improved plant feed grade provided by the Floatex has allowed for either an increase in overall plant capacity and/or final product grade. This paper will present the findings from the in-plant study.

Jan 1, 1996

By T. G. Hayes

Economic and environmental regulations in the coal industry have required companies to evaluate their current blasting method of loosening in-situ coal. This paper will review ripping vs. blasting thick in-situ coal seams, handling frozen active coal stockpiles and proper stockpile conditioning and reclaiming. How basic operating technique can improve job efficiency, productivity and cost per ton.

Jan 1, 1995

By Fred Pena

The VERTIMILL has proven itself to be a reliable performer in heavy duty industrial applications. Applications have been extensively used in the mining industry, flue gas desulfurization applications, and industrial minerals field. The machine is a vertically stirred machine that utilizes a screw operating in a grinding media. Grinding media types have ranged from several sizes of steel balls as the most common to pebbles or ceramic media. Mesh-of-grind and final product size are the determining criterion for the selection of the media size used. Product size consists have ranged from very coarse to super-fine grinds of less than 25 microns. Savings in consumption of power, grinding media, and liners when compared to a conventional ball mills, have been realized. Savings in consumption of reagents have also been demonstrated.

Jan 1, 1992

By R. Quintero

The HYL Direct Reduction Process was the first in the world to operate successfully at industrial scale. The results were so innovative and attractive that other steelmaking companies acquired licenses for the HYL Process. Now in its 40th year of commercial operation, the HYL process has evolved into a modem, highly efficient and economical technology -HYL III. The technology offers high productivity, minimum energy and water consumption, electricity co-generation, raw material flexibility, premium quality DRI/HBI, and is highly versatile for meeting the specific needs of each user. A historical review as well as recent developments and future plans are presented in this paper.

Jan 1, 1998

By H. Sevim

In a recently developed long term open pit production planning model, the optimum plan is found by exhaustively searching through nested pits of maximum-metal contents. A more efficient, dynamic programming (DP) based search algorithm now replaces the exhaustive search algorithm which was requiring prohibitively long execution time in real life cases. The logic and the formulation of the newly developed search algorithm are illustrated through a small hypothetical case. A real life gold deposit is treated to demonstrate that the algorithm does indeed find the optimum production plan among all possible plans. A comparison, in terms of computational savings between the two algorithms is also given.

Jan 1, 1994

By Yuting Xue, Todd Minoski, Daniel Su, Mark Van Dyke, Mark Mazzella, Steve Hicks, Zoheir Khademian, Nicole Evanek

Design of chain pillars in a longwall mine setting is one of the main engineering controls on the global and local stability of the mine. Challenges with roof instabilities, floor heaves, and pillar failures can be alleviated, to some extent, by careful design of gateroad configurations and chain pillars. This work investigates three different alternative designs in a three-entry-system gateroad configuration with an inter-panel barrier in a longwall mine in Virginia. Starting with the current design, which has faced challenges such as excessive floor heave, a geomechanical model developed in 3DEC software is validated by monitoring in-situ pillar stress in the yield, abutment, and barrier pillars in the mine. Next, three different chain pillar designs are evaluated in the model with a focus on roof sagging, floor heave, and pillar average stress. Results show the relationships among the alternative designs and instabilities associated with roof, pillar, and floor in the study mine, providing insights for optimizing longwall mining designs in deep-cover settings.

Feb 1, 2025

By M. G. Gorman

The effects of particle size, particle shape and degree of aggregation on n-dodecylamine flotation of -20 µ m quartz and glass beads were studied. A microflotation cell suitable for use with very fine particles was used in the flotation experimentation. Degree of agglomeration of particles was estimated by comparing size distributions of the quartz and beads in a dispersed system to size distributions in systems in which the collector was present. Results obtained show that in such flotation systems the fine particles are not generally present as individual particles during flotation but rather as aggregations. However, the quartz floats more readily than the beads indicating that there are some shape effects in the systems, considering the large specific surface areas of the materials it also appears that substantial amine consumption in the systems may limit flotation or lead to a requirement of greater reagent dosage for equivalent flotation to that tor larger particles.

Jan 1, 1990

By J. K. Ross, K. O. Hoal, S. K. Appleby

Understanding ore variability is a key factor in the geometallurgical analysis of a deposit and is beneficial to process development and mine planning. Ore variability is a function of the mineralogy of a deposit, in terms of both ore and gangue minerals and their textural relationships. This study integrates optical microscopy and quantitative mineral analysis to characterize the mineralogy and texture from 13 samples from different lithologic units at the Bingham Canyon Mine. The analysis identified several parameters, such as modal mineralogy, alteration assemblages, distribution of mineral phases and alteration assemblages and microfracture and void space distribution. These parameters can have an impact on the materials’ behavior during processing. This study demonstrates that quantitative mineralogical analysis can provide detailed information for improved understanding of ore variability.

Jan 1, 2010