Search Documents

By E. Zahl, J. Whyatt, H. Lawson

The U.S. Mine Safety and Health Administration (MSHA) issued Program Information Bulletin P09-03 in April 2008, providing formal guidance on using programs that model the redistribution of stress during underground mining of coal. A key part of this guidance is visual observation and mapping of ground conditions. If a correlation between ground conditions and model output can be established, the model is considered to be verified, and can be used to guide mine design in similar ground. A simple scale is recommended for ranking observed roof, rib and floor conditions. This paper discusses optimization and implementation of a ground condition rating scheme in the gateroads of a deep underground longwall coal mine. Roughly 80% of each gateroad length deteriorated in a fairly uniform manner. However, this manner varied between gateroads, as did pillar size. The implementation of a ground condition mapping program, similar to that recommended in PIB P09-03, was successful in characterizing the ground response to mining in gateroads of a longwall coal mine.

Jan 1, 2013

By Andrew Thomson, Peter Wright

"A section of a London Underground expanded segmental lined tunnel constructed in the 1970’s progressively deteriorated after 2001, with extensive radial joint spalling and mid-segment cracking. As part of the PPP contract Tube Lines Ltd and their partners carried out various analyses of the tunnel, including analysis of laser scans of the tunnel, geotechnical testing through the tunnel walls, geotechnical desk studies, real-time monitoring and even full-scale segment testing. This paper discusses the behaviour of the tunnel lining in this setting, the causes of failure and the lessons that can be learnt from this rare example of a tunnel which was progressively failing in service. It is finally noted that a replacement tunnel lining was installed during night-time possessions and completed in 2015. INTRODUCTION In 2003, Tube Lines Ltd. was established under a Public-Private Partnership (PPP) scheme to provide maintenance services and upgrade projects for London Underground (LU). The Deep Tube Tunnel Knowledge and Inspection Programme comprised the assessment of all tunnels, shafts and other underground structures. This included a number of lengths of tunnel constructed using segmental concrete linings. First used by LU in the 1960s, the savings both in cost and speed of construction led to concrete linings replacing cast iron for new tunnel construction in all but a few cases. During the initial scoping phase of this programme, inspections identified potential issues with the expanded concrete segmental linings on the Jubilee line. The inspections found a number of segments with surface spalling (Figure 1a), which did not appear on the post-construction defect records. These were generally relatively shallow, up to 40mm deep, spread over a wide area of segment. These were different to spalls caused by handling damage, which are typically localised at segment corners. Subsequent inspections over the following years identified an increasing number of segments with these types of spalls as well as an increased incidence of longitudinal mid-segment cracking (Figure 1b). The increasing occurrence of these defects was hypothesised to be caused by tensile stresses developing in the vicinity of the joint."

Jan 1, 2016

By R. Schuerch, C. Cimiotti, G. Anagnostou, J. Nickerson, P. Perazzelli

"This paper presents experiences gained from the construction of the Lake Mead Intake No. 3 project. The 4.7 km long tunnel was excavated with a hybrid TBM (able to operate in both closed and open mode). The tunnel crossed metamorphic and sedimentary rocks under a hydrostatic pressure of about 14 bar. During the excavation of the tunnel the TBM encountered difficult ground conditions caused by a combination of high water pressure, poor ground quality and locally low depth of cover. The adverse conditions required the TBM to be driven in closed mode at very high support pressures (10 – 15 bar) for approximately 60% of the tunnel length. The paper summarizes the main problems encountered during TBM excavation and analyzes the evolution of the TBM parameters over the entire tunnel length. INTRODUCTION The Lake Mead Intake No. 3 project is located approximately 30 km away from the city of Las Vegas in Nevada, USA. The project consists of the construction of a deeper third intake for the biggest reservoir in the United States, which is formed by the Hoover Dam. The construction of the new intake was required due to the constant drawdown of the lake level (more than 40 m in the past 20 years) and the consequent risk that the shallower intakes 1 & 2 may run dry. The project included the fabrication and positioning on the lake bottom of an intake riser, the excavation and lining of a 185 m deep shaft and construction of a 4.7 km long tunnel. One peculiarity of the project is that the water table is located about 140 m above the tunnel elevation (i.e. corresponding to a hydrostatic pressure of 14 bar at the current lake level). The tunnel was constructed using a tunnel boring machine (TBM) able to operate in both open and closed mode (Mc Donald & Burger, 2009). The present paper focuses on the TBM tunneling experience gained from the Lake Mead Intake No. 3 tunnel. The TBM excavation started on December 27, 2011 and finished on December 10, 2014 with the breakthrough to the intake structure at the bottom of Lake Mead. GEOLOGICAL CONDITIONS The assessment of the ground conditions encountered during construction was mainly based upon qualitative descriptions of the tunnel face conditions (during open mode operations) and analysis of the extracted muck (during closed mode operations)."

Jan 1, 2016

By Richard J. Ebens

The trace element geochemistry of the cherty, clay-rich carbonate residuum. Covering much of southern Missouri and adjacent parts of Arkansas was investigated during the early 1970's as part of a statewide geochemical survey of Missouri-1/2/3 The study was environmentally oriented and focused on the character of the "natural' geochemical environment of the state. A great deal of effort was made to collect samples that would represent the geochemical variability of the near-surface environment in an unbiased way. In general, this was accomplished by use of randomization procedures in both collection and analysis. Most of the sampling sites were selected randomly to prevent personal bias from entering into sample selection. In the laboratory, samples were analyzed in a randomized sequence to circumvent the effects of any systematic bias that may have entered into the laboratory procedures. Several residuum samples contained 1 000 parts per million (ppm) or more of Pb, Zn and Ba. All these samples were collected in Washington County in or near the barite district. The frequency distributions shown in figure 1 indicate just how unusual the residuum in Washington County is with regard to these three metals and copper. The shaded parts of the histograms represent the samples from Washington County. The histograms are based on analyses of 141 samples from 38 localities scattered over the subcrop of the Cambrian and Ordovician Formations of southern Missouri and northern Arkansas. Eight localities were selected randomly from over each of four bedrock units--Bonneterre Dolomite, Potosi and Eminence Dolomites, Roubidoux Formation, and the Jefferson City, Powell and Cotter Dolomites. Six localities were selected randomly from over the Gasconade Dolomite. The geochemical "background" for these elements in residuum is defined by samples from outside of Washington County (unshaded part of the histogram); lognormal distribution curves have been fitted to the corresponding parts of each histogram. Clearly, these lognormal models (curves) describe well the background

Jan 1, 1977

By Son Hoang Nguyen, Thanh‑Hai Pham, Duoc Van Tran, Dung Thi Kim Nhu

Apatite ore plays a critical and irreplaceable role in fertilizer production and is being upgraded in quality in northern Vietnam. The old tailing of the Bac Nhac Son beneficiation plant (Vietnam) has a significant apatite amount in the form of coarse unliberated particles. These millions of tons of tailing ore have 6–8% of P2O5 content, which can be retreated to provide fertilizer factories. This work presents the results obtained in recovering apatite from this tailing in the laboratory. By the combination of the processes of classification, preliminary flotation, re-grinding and cleaning in the flotation column, an apatite concentrate of 30.68% P2O5 can be obtained with the total recovery of 37.76% from the initial tailing of 7.56% P2O5. The study results not only provide an appropriate technical solution for recovering the apatite ore from tailing ore but also have outstanding meaningness in the recovery of mineral resources under the context of a circular economy.

May 24, 2023

By Verya Nasri, Kevin Akbarpour, Hiva Mahdavi

"The Sheppard East Light Rail Transit (SELRT) project comprises approximately 13 km of new light rail, which will be constructed along Sheppard Avenue East in Toronto. There is a 380 metre long section of the route that will be constructed as tunnel below Highway 404, which is owned by the Ministry of Transportation Ontario (MTO). MTO has published guidelines for tunneling under its highways. An impact analysis was undertaken to predict the surface settlement and angular distortion of Highway 404 resulting from the construction of the twin tunnels. The results were then compared to the performance criteria defined in MTO’s guidelines. As a result of this analysis, it was necessary to request an adjustment to MTO’s current performance criteria. This paper presents details and results of the impact assessment, approaches taken to satisfy the requirements defined by MTO, and provides details of the adjustment permitted by MTO. INTRODUCTION Several major rapid transit projects are planned for the Greater Toronto and Hamilton Area (GTHA) located in southern Ontario, Canada. These projects are part of The Big Move (Metrolinx 2008) initiative, a 25-year, and $50 billion plan aimed at improving regional transportation. Metrolinx, an agency of the Government of Ontario, is now working collaboratively across the region to deliver major Toronto rapid transit projects to the GTHA. One such project is the SELRT. The line will largely run along Sheppard Avenue East on the surface, except for a crossing of Highway 404 where it will be constructed using a combination of open cut and bored tunneling methods. AECOM has been retained by Metrolinx as the Technical Advisor (TA) to develop the Reference Conceptual Design (RCD) and Project Specific Output Specifications (PSOS) for the project. Also, Infrastructure Ontario (IO) is the Co-Sponsor and CH2M HILL is Metrolinx’s Owner’s Engineer (OE) & Project Management Support (PMS) for the new LRT lines. This paper presents information on the tunneling settlement analysis and further work undertaken to satisfy the MTO’s requirements."

Jan 1, 2016

By Jack Barrett

The oxidants which participate in the bacterially catalyzed oxidation of minerals are dissolved oxygen and some aqueous iron(III) complexes. Speciation studies indicate that these complexes consist of iron (III) -sulfate and iron (III) -arsenate ions. The complexes have different oxidizing powers as indicated by their calculated standard reduction potentials. The thermodynamics of the oxidations of pyrite and arsenopyrite are related to the mechanisms of the reactions. The mechanisms are discussed in terms of primary processes occurring on the mineral surfaces and the secondary reactions of the primary products. The importance of the conclusions to plant operation is discussed.

Jan 1, 1993

By J. Killian, S. Cox

Many questions exist within the geotechnical industry as to the applicability of Strength Reduction Factor (SRF) values to the design acceptance criteria (DAC) of mining operations. There are many factors that contribute to changes in the SRF estimate, some of which are numerical (e.g. dilation angle) and some of which are geometric (e.g. model grid size)[1]. Numerous studies have confirmed equivalent values of SRF and FOS are found for soil slopes of limited height as presented in, [2] and [3]. However, significant deviation of the SRF value was observed for highly cohesive materials (rock slopes) of heights typically encountered in mining, [4]. This paper builds on the work presented in [4], providing a more rigorous examination of the modeling parameters that control the SRF estimate. The failure mechanism assumed for this study was a simple circular shear surface in a uniform material. Both LEM and numerical methods are suited well for analysis of this failure mechanism. A parametric study was completed to evaluate and test the relationships of key numerical variables that affect the estimated value of the SRF using Itasca’s Fast Lagrangian Analysis of Continua (FLACTM) software. The effect of groundwater has been tested and may be significant but is not presented as part of this body of work for brevity and simplicity of presentation.

Mar 2, 2022

By T. Wisdom, D. Romo, G. Seale, R. Jansen

Thickening remains relatively misunderstood since it is typically near the end of the process and not directly involved in metal recovery. When operating well, thickeners are ignored and left to run independently, the ‘out of sight, out of mind’ phenomena. However, when operating poorly, there is a lack of basic understanding and remedial actions to solve issues are reactionary rather than proactively addressing shortcomings. This series of papers breaks down in sequential order the stepped phases required to gain an appreciation and thorough understanding of the science behind thickeners, and key thickener components, and basic troubleshooting skills. This second paper starts with identifying the different approaches to thickener test work including static and dynamic settling tests followed by high-rate versus paste thickening. Complimentary to test work, the mechanisms surrounding coagulation and flocculation are presented and explained. The basic mechanisms for coagulation and flocculation are discussed to support the different test work approaches and provide the reader with the basic background.

Mar 2, 2022

By R. Asmatulu

According to Darcy?s law, the rate of filtration should increase with increasing pressure drop across a filter cake. In centrifugal filtration, the driving pressure is created by the centrifugal forces applied in the free water on the surface of a filter cake. However, the pressure drop can become negative when the free water surface disappears, which makes it difficult to achieve low cake moistures. In hyperbaric centrifugal filtration, this problem is overcome using air pressure to restore the pressure differential. In the present work, various mineral and coal fines have been subjected to hyperbaric centrifugal filtration tests. The laboratory tests show that the moistures of various mineral fines, such as copper and zinc concentrates, phosphate, talc, kaolin clay, and precipitated calcium carbonate, can be reduced substantially below that achieved by conventional centrifuges. Similar promising results have also been obtained with various coal fines in laboratory and pilot-scale test programs and in full-scale plant demonstrations.

Jan 1, 2012

By Lawrence A. Roe

This paper describes research and development efforts leading to a wet process for the beneficiation of Western talc ores in which the values are primarily present as soft, platy talc mineral. The mineralogy of the ore, as it relates to the logic of utilizing an uncomplicated, attrition-scrubbing sedimentation process is described. Bench-scale laboratory testwork and a pilot-plant test program are described. The pilot-plant program included production of several tons of products. The thickened talc slurries were very difficult to dewater prior to the drying step. Dewatering difficulties were overcome by use of a high-speed centrifuge. The centrifuge cake was dried either by tray, flash or spray drying. The successful use of one high-grade talc product as titanium dioxide extender in paper is discussed. The talc product has extremely low abrasion values, an important characteristic for minerals used in paper manufacture. It is concluded that this wet process for soft talc ores is capable of producing high-purity talc products for paint, paper, cosmetics and other industrial uses re-quiring very pure soft talc.

Jan 1, 1972

By Thomas Schwind, Elmar Feigl, Gerald Skalla, Angelos Gakis

Cedarvale station was constructed as part of the Eglinton Crosstown Light Rail Line, under the operational Yonge-University Line Subway box of Toronto Transit Commission (TTC). The station was constructed as an open-cut, which necessitated the underpinning of the existing TTC box to minimize the impact on the Subway and allow its unhindered operation. Six mined galleries, 4 m wide by 2.75 m high, were excavated sequentially (SEM) immediately under the existing box, to provide the required space for the installation of the main underpinning beams. This novel solution was executed successfully providing quick access for the main excavation works to commence.

Dec 1, 2022

By Abdullah Arik

Verification of computer generated reserve models is essential since the computer does not automatically check the validity of methods and assumptions selected by the user and their results. For the computer to do model verification would require an expert system which would perform tests on the model and determine if the model is valid. Since such an expert system is not available, it is up to users to verify the models they develop.

Jan 1, 1995

By Shawna Von Stockhausen, Hong Yang, Tung T. Vu, Derek Penrice, Kevin Huynh

"The Regional Connector Transit Corridor is a 1.9 mile long light rail transit project in downtown Los Angeles, California. The project includes approximately 4,930 feet of twin bored tunnels together with a mined crossover cavern, 3 deep stations, and other cut-and-cover structures. The bored tunnels will be excavated using an earth pressure balance tunnel boring machine through Fernando Formation (extremely weak to weak rock) and alluvium. The tunneling will be performed in close proximity to a large number of existing structures, including the existing Metro Red Line tunnels with as little as 6 feet of separation. Thus, the evaluations of the tunneling effect on these structures and the instrumentation and monitoring program is an essential part of the project design. This paper provides a very brief overview of the considerations and evaluations of the tunneling effects on the existing structures and results of evaluation obtained during the final design stage of the project. INTRODUCTION The proposed Regional Connector Transit Corridor (RCTC) project provides a 1.9 mile-long connection between the Metro Gold Line from Pasadena and East Los Angeles; and the Metro Blue Line to Long Beach and the Expo Line to Culver City. The alignment is shown in Figure 1. The Regional Connector will provide new tracks through downtown Los Angeles. The project will extend underground from the Metro Blue, Expo, Red, and Purple Lines’ 7th Street/Metro Center Station following Flower Street, curving northeast to the north of 3rd Street under the 2nd Street Tunnel. The alignment will then continue eastward under 2nd Street, turning northeast to cross under the intersection of 1st and Alameda Streets, then splitting into two branches above the ground surface, one branch extending north along Alameda Street and the other extending east along 1st Street. The project elements include 3 deep stations, a SEM cavern, segments of TBM bored tunnels, and cut-and-cover guideway structures. The bored tunnels have an excavated diameter of 20.3 feet. The subsurface conditions along the tunnel alignment generally consist of artificial fill overlaying finer-grained alluvium (dominantly medium dense to dense sandy soils), underlain by coarser-grained alluvium (a wide variety of medium dense to dense sandy and gravely soils). Below the coarser-grained alluvium is Fernando Formation, which is characterized as extremely weak to very weak sedimentary bedrock. A long stretch of the alignment will be excavated in this formation. The soil layers above the Fernando Formation are of variable thickness and spatial distribution. The geologic profile is shown in Figure 2."

Jan 1, 2016

By Thomas N. Walthier

Exploration is the systematically financed and technically oriented search for mineral wealth. Almost all established mining companies have an exploration department. The size of a company's search varies over the years as the company's profits, or the corporate philosophy change. While the established mining companies have exploration departments, they are also alert to acquiring discoveries made by others -- especially by prospectors and small companies without the resources to develop their find. The emphasis in some large companies stresses self-generated discoveries while others rely heavily on acquisitions; again, over the years the emphasis may alternate. In the last analysis, essentially all new mineral wealth was found through someone's exploration effort. Before we discuss how exploration is financed, it will be informative to analyze how discoveries have been made and by whom. Recently, the author conducted a survey of randomly selected major mining companies to answer these questions. Most companies responded and many went to considerable effort to give complete and detailed answers. I thank all for their help and cooperation. The questionnaire is attached as Appendix I. Appendix II is a list of the 400 companies that replied in a complete enough manner and format to be analyzed here. The results of the questionnaire are given in Table 1. Over 57% of the new orebodies acquired by 40 major mining companies during the past quarter of a century were generated

Jan 1, 1977

The amount of hydrophobic materials constituting the mineral froth strongly influences the froth viscosity. Higher froth viscosity on the other hand can retard the drainage of physically carried over hydrophobic particles. In phosphate flotation tests a direct correlation was observed between froth viscosity and recovery and an inverse correlation between froth viscosity and grade. Phosphate flotation tests in the presence of a silica depressant indicated that higher froth viscosity is an effect rather than a cause of silica particles reporting in the froth.

Jan 1, 1992

By H. P. Knudsen

In most open pit gold mines ore waste selection is based on estimates made from blasthole samples. These estimates frequently are biased. While it is true that high grades and "outliers" can induce a bias they may not be the only reason for the persistent bias seen at many mines. This paper focuses on a source of the conditional bias. In this paper it is shown that the poor blasthole sampling can cause a conditional bias in the estimates.

Jan 1, 1991

By Xinyang Yu

The flotation of diaspore, kaolinite, pyrophyllite, illite and the diaspore-kaolinite mixture were studied with a new cationic organosilicon quaternary ammonium collector entitled QAS222. The acting mechanism of the collector with the four minerals was analyzed by Zeta potential measurement and FT-IR spectrum analysis. The results indicate that the QAS222 was effective in the reverse flotation of the diaspore-bauxite mixture of different Al2O3 -to-SiO2 mass ratios (A/S ratio) at an optimum pulp pH of 11. The potentials of the four minerals increased when they were conditioned in the QAS222 solution; however, the potentials of the three aluminosilicate minerals increased faster than that of the diaspore, especially at pH>9. Furthermore, they were positive in a wide pH range, indicating that QAS222 has a strong adsorption on the surface of the aluminosilicate minerals and thus that these minerals can be floated. The FT-IR spectra analysis further indicates that, besides electrostatic adsorp-tions, formation of the hydrogen bond and ammonium absorptions, chemical adsorptions occur between QAS222 and the aluminosilicate minerals, which allow for the QAS222 to be strongly adsorbed on the aluminosilicate minerals. However, these reactions between QAS222 and diaspore at pulp pH=11 are weaker than those of the aluminosilicate minerals. Thus, surface adsorptions cannot be formed effectively, resulting in reduced floatability.

Jan 1, 2010

By M. A. Reyes, L. Yan

"Heat and humidity buildup within refuge alternatives (RAs) may expose occupants to physiological hazards such as heat stress. Mine Safety and Health Administration (MSHA) regulations require RAs in underground coal mines to provide a life-sustaining environment for miners trapped underground when escape is impossible. RAs are required to sustain life for 96 hours while maintaining an apparent temperature (AT) below 95°F (35°C). NIOSH tested a 10-person tent-type RA, a 23-person tent-type RA, and a 6-person metal-type RA in NIOSH underground coal mine facilities to investigate the thermal environment over a 96-hour period. The test results showed that mine air and mine strata temperatures surrounding an RA occupied by simulated miners increased over the 96-hour test period. The test results suggest that RA manufacturers should consider this increase in temperatures when calculating and evaluating RA components during surface and laboratory tests. The findings can equip stakeholders with additional considerations for calculating heat and humidity temperature profiles for RAs not tested in situ. INTRODUCTION RAs are designed to provide a life-sustaining environment for miners who cannot escape after a mine disaster. One of the major considerations for integrating RAs in mine environments is the thermal environment inside the RA and the impact that the surrounding mine conditions have on the temperature and humidity buildup. Previous research has observed that the metabolic heat of the occupants and the heat released by the CO2 scrubbing systems will cause the RA interior air temperature to increase. In addition to the increase in temperature, an occupant’s respiration and perspiration, as well as the chemical reaction of the scrubbing chemicals with CO2, will contribute to an increase in humidity within the RA. The resulting internal thermal conditions, if not controlled, can subject miners to conditions that can lead to heat exhaustion, heat stroke, or even death depending on the duration and magnitude of exposure. Apparent temperature (AT) is a temperature-humidity metric for the perceived temperature caused by the combined effects of air temperature, relative humidity (RH), and wind speed. It is used to assess the perception of indoor temperatures when workplaces are not sufficiently heated, cooled, or insulated to provide comfortable or healthy conditions. Mine Safety and Health Administration (MSHA) regulations require that RAs must be designed to ensure that the internal AT does not exceed 95°F (35°C) when the RA is fully occupied."

Jan 1, 2018

By E. Sabah

A series of adsorption tests are carried out to understand the ability of cationic surfactants and metal ions to adsorb onto sepiolite. Adsorption tests conducted as a function of heat treatment reveal that sepiolite is rather conducive to the uptake of both organic and inorganic ions. An ion exchange mechanism between surfactant or metal cation and magnesium ion followed by chain-chain association is proposed to explain the incorporation of cationic surfactants into the structure of sepiolite.

Jan 1, 1998