Search Documents

By Steven W. Hunt, Jane A. Kettler, Barry R. Doyle

A sewer tunnel being constructed through an urban commercial area was to pass the site of a former gasoline service station. The site was known to have contained leaking underground storage tanks. An environmental assessment of soils on the alignment was performed, and measures were implemented to handle expected contaminants. Despite these precautions, an explosion occurred in the heading when liquid gasoline was encountered. Four workers were injured. This paper presents the findings of an investigation into the cause of the explosion, and examines how concerted efforts by the parties involved failed to prevent it. The level of guidance provided by OSHA Code provisions for tunneling in gassy conditions is discussed.

Jan 1, 1997

By Alwyn Protheroe, Steve Smith, Herbert Jr. Gibson

In September of 2000, Cowin and Company, Inc., contracted with Paramont Coal Corporation to construct a large decline approximately 820 m (2,700 feet) in overall length at a grade of 8 degrees to the Lower Banner Coal Seam. This paper will discuss the methods used by the contractor and owner to overcome the unique problems required to construct this tunnel in a coal mine environment. The problems include, initial design considerations, equipment selection, ventilation, ground control, control of water in?ows, and placement of concrete.

Jan 1, 2003

By Glenn M. Boyce, Timothy R. Coss

Microtunneling first appeared with some regularity in the United States in 1987. Until then, only Japan and Germany utilized this method of construction. Its high costs initially limited its application to special situations. The last ten years have seen the use of new pipe materials, new machines, new cutterheads, new techniques, and an average growth of30 percent each year. This paper documents the growth and changes that have occurred with microtunneling. Based on current industry practices and advances from abroad, this paper postulates what the next ten years may hold.

Jan 1, 1997

By A. Geertsema

Introduction Gasification of coal has been practiced for many decades for the production of gas, fuels, chemicals and power. However it has only more recently started to get significant attention in the USA. In this review of the basics the features of gasification as compared with combustion is covered and the potential of increasing the conversion of coal via gasification is indicated. After dealing with the fundamentals of gasification a review of gasification technologies will be presented with an indication of the widespread international and more limited US use of this technology. In conclusion the attention will be directed at the future prospects of gasification.

Jan 1, 2006

By Andy W. Stephens, William H. Langer

In Australia and America, encroachment by conflicting land uses, zoning restrictions, and the "not in my backyard" syndrome make it increasingly difficult to access high-quality aggregate resources located near the market areas. Attempts by government agencies in America to protect aggregate resources for future development have met with varying degrees of success. The State of Queensland, Australia, designates aggregate resource areas as Key Resource Areas, which protect the resource and the routes to transport the resource, provide a separation area from incompatible land uses, and indicate the likelihood that the area is free from conflicting social or environmental issues.

Jan 1, 2005

By M. S. Seehra, V. Suresh Babu, R. S. Pandurangi

Different mixtures of the three polymorphs of silica viz. quartz, cristobalite and tridymite are analyzed by x-ray diffraction (XRD) and their IR spectra are investigated by photoacoustic spectroscopy. It is observed that XRD provides a higher resolution to distinguish between the three polymorphs in a sample than IR spectroscopy. In the latter, a sharp band near 617 cm-1 is characteristic of both cristobalite and tridymite. A mine dust sample is quantitatively analyzed by XRD and it is shown to contain illite, quartz, kaolinite and calcite.

Jan 1, 1991

By P. Pages, J. Lombard, F. Fagnant, G. Bresson

This study is devoted to the improvement of the decision-making process in occupational protection of uranium miners in France. Its purpose is to apply the principles which are recommended by the I.C.R.P. in the field of radiation hazards. These principles, which have introduced the notion of "optimization" in standard setting, suggest the importance of applying cost-benefit and cost-effectiveness analysis to this sector. The objectives here are twofold : to evaluate the present organization of radiation protection on the basis of a simulation model of polluted air flow in the mine (due to the decay of a radioactive gas, radon) and to develop cost-effectiveness analysis of the various radiation protection policies.

Jan 1, 1981

By E. D. Seymour

Minera Yanacocha operates a complex heap leach gold facility in the Northern Andes of Peru. Four leach pads and thirteen solution storage process ponds form an extremely complex system. Distinctly different wet season and dry season rainfall accumulations present unique challenges to the process water balance. Minera Yanacocha operates four excess water treatment facilities which discharge water to the environment at specific quality standards in order to maintain a balanced system. Numerous government agencies and non-government organizations are involved with the permitting, monitoring and control of the discharged water. Minera Yanacocha maintains a relationship with 65 villages and communities, with a population of approximately 29,000 people and the city of Cajamarca with approximately 100,000 residents. This paper provides a high level review of the system complexity, the water balance, the excess water treatment facilities and social aspects of solution management.

Jan 1, 2004

By V. Saltas

The present work investigates whether dielectric spectroscopy can be used to detect contamination, which may appear in a natural porous material, due to the spreading of pollution. For this purpose, dielectric and conductivity measurements, in the frequency range of 10mHz to 1MHz, were carried out in sandstone samples, partially filled or saturated with solutions of leachates, at different concentrations. The experimental results suggest that although the role of water is dominant to the measured electrical conductivity, variations of two orders of magnitude are observed due to the different concentrations of leachates, in partially filled sandstone samples. Experimental data are well fitted with a Havriliak?Negami dielectric relaxation function, superimposed with a conductivity term. The parameters of the fitting function have been correlated to the concentration of leachate in the sandstone samples and considerable changes have been observed at low leachate?s concentration.

Jan 1, 2005

The challenge of the sustainable development framework in mining today is to see that the minerals sector as a whole contributes to human welfare and well-being without reducing the potential for future generations to do the same. If the minerals sector around the world is to contribute positively to sustainable development, it needs to demonstrate continuous improvement of its social, economic, and environmental contribution, with new and innovative governance systems. Canada is an international leader in mining and related technology. Metals and minerals is Canada?s second-largest earner of foreign exchange. Canadians, along with the rest of the world, are increasingly concerned about the environmental impact of mining activities. The Canadian Mineral industry has acknowledged the importance of its environmental responsibility by taking a broad range of innovative actions in order to ensure a sustainable development of its resources. This paper analyzes how the concept of sustainable development can be related to mineral enterprises. It discusses a wide range of issues under three main areas: perspectives on sustainable development; processes for furthering sustainable development; and assessment methodologies and indicators. This paper also presents a proposed framework and a core set of key sustainable development indicators that could be useful in efforts to measure progress toward sustainable development in mining. The paper concludes with a case study of some key sustainable development indicators related to the Canadian oilsands mining.

Jan 1, 2003

By Victor F. Hollister

This section on case histories of discoveries of volcanic-associated and volcanogenic massive sulfide deposits is divided into a preliminary discussion of models and then into three parts: Kuroko- type, Anyox-type, and shale-hosted. The separation is made to accommodate the use of exploration models, and these may not coincide with genetic models discussed in the literature. The exploration models grew as knowledge was gained concerning ore guides and ore controls in the volcanic-related deposits. The evolution of the genesis of massive sulfide deposits in volcanic terranes from a replacement to a syngenetic hypothesis in the 1950s and 1960s necessitated changes in exploration approaches in ore search. The acceptance of a syngenetic origin for conformable or concordant sulfide masses led to more widespread adoption of stratigraphic ore guides. 'The occurrence of epigenetic stringer ore with and stratigraphically below many conformable massive sulfide deposits did not diminish the importance of stratigraphic ore controls. Proximal conformable sulfide masses were formed near their seafloor hot spring source and normally are underlain by epigenetic sulfides: whereas. distal conformable sulfide masses were deposited away from the hot spring and may have no associated feede; zone. Industry groups that early recognized the syngenetic nature of volcanogenic massive sulfides were responsible for discovery of some of the large and economically significant deposits. Ultimately, the rest of the geological profession accepted the leadership of the early iconoclasts.

Jan 1, 1991

By A. Sfougaris

A study on fauna distribution and abundance is being conducted in the Giona Mountain, in central Greece, area of bauxite mining. The specific aims of the study are: a) to estimate and map the distribution of mammals, and especially of the Balkan chamois, b) to estimate and map the distribution and abundance of breeding birds, c) to count the bird species using the area during spring and autumn migration and winter, d) to update the list of mammal and bird species of the mountain, with emphasis on rare and endangered ones, according to 79/409, 92/43 EU Directives and other relevant conventions, e) to compare the bauxite mining areas and species distribution and assess the possible overlap and compatibility of mining activities - species conservation, f) to assess the possible habitat loss due to planned mining activities. All estimations of mammal species distribution and abundance are being carried out by fieldwork using spotlight during the night along selected routes. Especially for chamois, line transects and vantage points with the aid of telescopes and binoculars are being used. Birds are being counted with the point count method in randomly selected plots distributed in all available habitat types and altitudes. The species distribution and mining areas will appear on thematic maps with the aid of a geographical information system (GIS). Finally, solutions for environmentally compatible mining activity in the area will be proposed.

Jan 1, 2007

By F. Dudouit, M. M. Mohkam, F. Renault

The Pannerdensch Kanaal Tunnel is part of Holland’s Betuweroute high speed freight railway project linking Rotterdam to inland of Europe. It comprises of twin tunnels, 1620 m long each, with 8.6 m inner diameter. The Tunnel alignment is situated mainly in sandy formations and under high hydrostatique pressure. The over burden cover varies from relatively high to very low, sometimes much smaller than the diameter. One of the special features of the Pannerdensch Kanaal Tunnel is that, over some 250 m, the twin tunnels are to be bored in a back?lled sandpit. Some 490 000cubic meter of sand has been placed and compacted by vibro-?otation to refill the sandpit. The tunneling machine is a 9.8 m slurry shield manufactured by Herrenknecht. Tunnel lining is precast concrete consisting of seven plus one key universal segments. Other than the special feature of boring through re?lled sand, constraints such a slow overburden while crossing under Pannerdensch Kanaal and some lagoons, as well as high liquifaction potential of sandy formations, render this job very unique of the type. Fine studies were conducted in heading’s stability. And, confinement pressures were determined considering different risks of liquefaction and blowout problems. Both tubes have been successfully bored. Several sections have been monitored. The results are quite interesting and in accordance with contract technical conditions.

Jan 1, 2003

By Matteo Cortinovis, Giuseppe Gelmi

"INTRODUCTIONEdilmac dei F.lli Maccabelli (hereinafter referred to as Edilmac) has recently developed a special civil engineering application using the Raise Boring technology with the assistance of Inrock MGS (Magnetic Guidance System). Applying the Paratrack Magnetic Guidance System coupled with a directional mud motor to the drill string allows a better accuracy compared to standard drilling, as showed in our tests. This is the first time the Paratrack System has been applied to the Raise Boring technology. RAISE BORING METHOD STATEMENT The Raise Boring technology was born in North America during the Sixties. In 1962, Ingersoll and Robbins were the first companies to produce Raise Boring Machines (RBM). The technology was first used in the underground mine industry, in order to bore ventilation shafts and passes through different levels, thus reducing the cost of haulage. The Raise Boring method is only feasible in stable rock conditions. The Raise Boring method consists of drilling a small diameter pilot hole that reaches a tunnel located at the bottom of the drilled hole. Once the pilot hole reaches the tunnel, a reamer head is installed at the end of the drill string and pulled up, creating the hole with the designed diameter (Figures 1 and 2). The main equipment, which is required to perform Raise Boring activities, is the following: •,An RBM; •,A tricone bit; •,Drilling rods; •,A reaming head; The standard mucking of the pilot hole is done with water or bentonite mud. For the last 30 years, Edilmac has developed a mucking process, which uses compressed air with the addition of foam or a small amount of water for dust control.Pilot hole tricone. The drilling of the pilot hole is usually performed with a tricone bit having a diameter between 11” (27.61 cm) and 15” (38.10 cm) (Figure 3). High strength rods. They generally have a diameter ranging from 10” (25.40 cm) to 12 ?” (32.70 cm) (Figure 4), depending on the length and the final diameter of the shaft."

Jan 1, 2016

By T. J. Fenner

Research conducted in South African mines has demonstrated the benefit of ground penetrating radar for the detection of geologic features and hazards. This is crucial for safety and production considerations in underground mines that are as much as 4 kilometers deep. This paper describes a new ground penetrating radar system designed specifically for high quality data acquisition, in the harsh conditions of deep underground environments, for use by operators with minimal geophysical experience. Design criteria included automated functions, intrinsic safety, light weight and minimal power requirements. Data is processed on the ground surface by geoscientists using a PC.

Jan 1, 1994

By D. Kruse, M. Sanaei

"A three dimensional nonlinear finite element model was constructed to simulate and analyze the behavior of large diameter segmentally lined shafts when subjected to seismic waves. To reduce computation time, a less complex shell model was also constructed. Transient excitation was applied to the supported nodes of both models, at the base of the shaft, with a time-function representing the 1994 Northridge earthquake. The models are developed at the end of an original phased construction-stage analysis of the shaft. Displacements, forces and moments are monitored and compared during the analyses steps. During the initial 15 seconds of the earthquake, the top and bottom of the shaft show similar displacements. The maximum horizontal displacement within the shaft is approximately 3.5 inches in the solid model and the shell model results conform to this by a factor of 50%. Keywords: Segmentally Lined Shaft, Soil Structure Interaction, Seismic Analysis, Finite Element Modeling, Ground Modification INTRODUCTION TO SEGMENTALLY LINED SHAFTS Large diameter segmentally lined shafts (SLS) are underground systems, constructed sequentially using precast concrete segments to form a ring which provides both temporary earth support during excavation and permanent structural support. The segments are connected via alignment pins, bolts, packer material and other structural components that ensure the continuity of the SLS. In this analysis, the construction process uses a top-down sequence wherein each soil layer is excavated, damp-proofing is installed and concrete segments are assembled to form each ring. This process is repeated until design depths are achieved completing the shaft. It is known that cylindrical structures sustain lateral (earth) pressure mainly through the mechanism of hoop-stress. As Timoshenko’s ring theory goes, a cylinder shell structure is prone to buckling under external pressure [1]. In typical designs of small diameter shafts and tunnel linings with small diameter to wall thickness ratios, nonlinear buckling analysis (i.e., nonlinear geometric analysis) is not considered, since the buckling capacities for those structures are much higher than typical pressures encountered at their design depths. However, in shafts with large diameter to wall thickness ratios, buckling could become a critical issue. In any given mode, as buckling occurs in a ring, some sections of the structure move inward while alternating sections protrude. Although the presence of the surrounding soil could mitigate the buckling by resisting the movement (Soil structure interaction) seismic loads can cause ground movements and lateral pressures, exceeding the capacity of the structure. It is therefore essential to design the load bearing capacities of the shaft to minimize the possibility of any catastrophic failure due to earthquakes. This study explores the structural response of the SLS when subjected to seismic loads."

Jan 1, 2016

By J. E. Golsan

Barrick Gold Corporation installed an expert style control system on the grinding circuit at its Mercur mine. Barrick's main objective was to increase mill throughput by a minimum of 3%. The expert system team collected operating data and then created a knowledge base using Comdale/X expert system development software. The expert system moved from on-line "advisory" mode, testing of expert rules, to full process control in four weeks. Expert system control benefits include a 9-15% increase in mill throughput, consistent mill loading leading to less wear on SAG mill parts, and improved downstream process control.

Jan 1, 1998

By N. Rocco, G. Johnson

Implementation of post-closure draindown estimates for tailings facilities are important predictive tools for reclamation planning and often influence jurisdictional bonding. Simplified estimates of draindown have been proposed in the past but these methods are not able to capture many of the site-specific nuances as well as operational and material parameters that influence robust draindown estimates. This paper discusses an iterative approach that relies on unsaturated flow models to predict draindown rates and associated pond inventory water balances that track inputs into underdrain pond systems, solution storage volumes, implementation of active evaporation, and necessary recirculation of solution back to the tailings facilities. Specific design criteria such as climate, facility geometry, material properties, and initial conditions, as well as active closure operational considerations that can influence draindown estimate will be discussed. Concepts presented will be valuable for operators, designers, and regulators to guide closure planning and predictive analytical analyses that support draindown estimates.

Mar 2, 2022

By R. Jin

Fine coal flotation using gaseous carbon dioxide has demonstrated the potential for producing superclean coal. The success of this new flotation .procedure is attributed to the coal's high adsorption potential for CO2. To understand the nature of gas-phase CO2 adsorption at the coal surface, in-situ FTIR spectroscopy in a controlled-environment chamber with an ultravacuum sys-tem has been used and the results are discussed in view of other experimental results from differential scanning calorimetry. It has been found that specifically adsorbed CO2 molecules at the coal surface are polarized and have a characteristic doublet at 2336 and 2361 cm-1. Two adsorption states have been proposed to account for the doublet observed from in-situ FTIR spectroscopy measurements. It is believed that the band at 2336 cm-1 originates from the activated site adsorption of CO2 and that the band at 2361 cm-1 arises due to the molecular aggregation of CO2 within the coal pores.

Jan 1, 1988

By Wayne R. Hopkins

Southern Arizona has one of the world's principal concentrations of copper ore bodies. Twenty miles south of Tucson, close to the Mexican border at Sahuarita in Pima County, is the Twin Buttes mine. In mid-1973, the Anaconda Company and American Metals Climax Incorporated (AMAX) established a 50-50 partnership to operate and expand the Twin Buttes property. Anamax Mining Company was established as the operating company for this joint venture. The production from the Twin Buttes mine is shared between the two partners who market independently. A major expansion of the Twin Buttes operation has included an accelerated stripping programrne for the pit, an expansion of the sulphide concentrator, the construction of an oxide leach plant and a 57 MW diesel generating power station. Part of this major expansion, the large tonnage oxide processing plant was brought on stream in 1975 and is now close to design capacity. The "mine to market gap" has been closed by producing high-purity copper cathodes at the mine site from oxide ore reserves. By using a hydrometallurgical process route, copper production is possible with negligible effects on the environment.

Jan 1, 1976