Search Documents

By E Marambio, R Brändle, G Fischer, G von Rickenbach, L Burgos, R Luis Fonseca

Ground support systems must provide safe and effective designs for underground excavations under high stress conditions. These systems must be capable to resist dynamic impacts and yielding during the loading process. In this context dynamic testing of the reinforcement and retaining elements that compose the ground support system are required to study and improve the behaviour of these elements under dynamic load events. During the last years, Geobrugg has been working on the improvement of retaining products by testing them in a large-scale impact test facility located at Walenstadt, Switzerland. The test facility is composed of a double level platform with a square-shaped pyramidal trunk geometry, in the upper level housing a loading mass that drop from a height up to 5m. The loading mass is guided by one central steel pipe, and the impact occurs in the sample to be tested located at the lower level in a slab with an area of 3.6m × 3.6m where the ground support system is installed. During the last years, this innovative facility has been used to test several configurations of ground support systems. The results of these tests have enabled to improve the understating of the behaviour of ground support systems under dynamic loads. In this manuscript, the arrangement, measurement, results, and the preliminary analysis of a single impact dynamic test performed during 2021 of a ground support system with a high-tensile steel wire mesh MINAX 80-4.6 is presented.

Apr 26, 2022

By T. C. Eisele

The separating efficiency of a flotation column is largely limited by the degree of backmixing of tailings into the froth zone, and its recovery is limited by the degree of short-circuiting of feed to the tailings. Current columns are typically made very tall, on the order of 30-40 feet, in order to limit the effects of backmixing and short-circuiting. These effects can also be reduced in a much shorter column, provided that the flow in the column approaches plug-flow. In this work, horizontal baffles were shown to improve the performance of a 6-foot tall laboratory-scale flotation column treating a difficult-to-clean, heavily oxidized coal. Tests with variation in the position of the baffles showed that for the greatest benefit, baffles are needed both above and below the feed inlet. Tracer tests with a fluorescent dye water tracer showed that the addition of the baffles reduced the amount of feed water entrained into the froth at any given coal recovery.

Jan 1, 1994

By K. W. Deter

The gold ores in the Jerritt Canyon district have been recognized as refractory since they were first encountered by FMC geologists in 1976. Upon obtaining managing rights as joint venture partner, Freeport McMoRan Inc. developed an operating plan featuring carbon-in-leach gold recovery techniques for the oxide portion of the ores and a patented sulphide oxidation step followed by chlorination for treating the organic carbon constituents of the refractory ores prior to CIL gold recovery. The plant was successfully started up in 1981 with the first gold poured on July 4, 1981. Initial plant throughput was designed to be 2495 MTPD (2750 STPD) total through the dual processing trains.

Jan 1, 1991

By Clarence A. Johnson

The discovery of the Prudhoe Bay field temporarily reduced interest in the development of coal conversion processes, but interest is being re¬newed by the current energy crisis. According to M.A. Wright, Chairman of the Board of Humble Oil and Refining Company(l), the reserve in the Prudhoe Bay bield has been confirmed to be about 10 billion barrels. At first glance this appears to be an extremely large reserve which will eliminate supply problems for the United States for some time. This feeling of security is lost when one realizes that by 1980 the world will consume the reserves of a Prudhoe Bay or a Libya, or Venezuela in less than a year, based on the recent predictions of U.S. and world reserves made by Eastman-Dillon, Union Securities Company(2). Recent forecasts of U.S. demand and source of supply made by Kenneth E. Hill of Eastman-Dillon are shown in Figure 1. This forecast shows a decline in domestic supplies (excluding Alaska) after 1973, with the total domestic supply leveling off in 1975 at about 13 million barrels per day. Since the predicted demand increases from about 14 million barrels per day in 1970 to about 20 million barrels per day in 1980, about 35% of domestic consumption must come from imports or non-conventional sources by 1980. More imminent is the shortage of low sulfur fuel oil which has been created by the new, tough air pollution regulations that are basically legis¬lating eastern coals out of the market. As an alternate to importing large quantities of low sulfur fuel oil or importing and desulfurizing regular fuel oil, one of two domestic solutions is possible: stack gas clean-up or solids fuel pretreatment. Stack gas clean-up may be the cheapest approach for old installations, but fuel pretreatment has real advantages for new installations. Coal pretreatment at the mine could eliminate all solids fuel handling

Jan 1, 1972

By R. R. Fernández

The Newmont roasting plant in Carlin, Nevada, commenced operating in December 1994. Over the years, refractory ores and pyrite concentrates from different gold deposits constituted the feed to the facilities. Historical plant performance indicated that the roasting temperature was the main variable affecting the structural characteristics of the calcine, which in turn affected the recovery of gold by cyanidation. Gold recovery as a function of roaster temperature has been closely monitored since October 2000. The original design temperature was 550° C. Lower roaster temperatures of around 500° C resulted in a gold recovery increase of more than six percent. This increase was directly related to an increase of the surface area of the calcine. The implementation of an ?intelligent? process control system helped significantly in achieving steady low roasting temperatures, thus obtaining high gold recoveries of 92 to 93 percent. Under these conditions, several roasting campaigns with high-arsenic-containing ores were conducted, which resulted in a significant decrease in gold recovery. The reduced gold recovery was caused by the loss of surface area (e.g., porosity) of the calcine as the arsenic content of the roaster feed increased.

Jan 1, 2010

By John A. Breslin

The U.S. Bureau of Mines develops technology to help ensure that the Nation has an adequate and dependable. supply of minerals at reasonable economic, human, and environmental cost. Our research programs seek improvements for almost every aspect of the mineral production cycle--from evaluating the availability of minerals, removing the ore from the earth, to enhancing the performance of mineral materials. The health and safety of the men and women who work in the Nation's mines and minerals processing plants and the environmental impact of mining and mineral processing are major Bureau research concerns. In recent years, the U.S. mineral industry has found it increasingly difficult to compete for a share of world markets. Many foreign producers benefit from lower production costs and higher grade deposits. Some foreign governments subsidize their mineral industries and impose fewer restrictions with respect to environmental controls and health and safety regulations. If the United States is to compete in world mineral markets, innovative technology must be found to lower the cost of recovering and processing minerals. Mining and mineral processing research by the Bureau identifies ways to help the country maintain a sound, competitive industry and a dependable mineral supply, so vital to economic growth and the national security. This work includes efforts to improve existing techniques and procedures; but more and more of the Bureau's resources are being focused on long-term, high-risk research directed at developing new approaches to mining and mineral activities--approaches like in situ mining. Bureau scientists are studying the mining applications of computer assisted mining and investigating a variety of "high tech" approaches to extractive metallurgy. Such cutting-edge research will be necessary if major advances in health and safety, environmental quality, strategic and critical minerals availability, and overall U.S. competitiveness are to be achieved. It is just such high-risk research that the industry cannot afford to conduct itself, but--in the long run--cannot afford to be without. It is this type of research that will help us arrive at a revolutionary breakthrough rather than small incremental changes in health and safety technology as well as recovery methods. Our mining and mineral processing research is also directed at reducing the Nation's dependence on imports of minerals that have key defense and industrial uses. Some of these strategic and critical minerals are particularly vulnerable to supply disruptions. We are working on technologies that would allow the United States to take advantage of domestic sources of these minerals--sources consisting primarily of deep or low-grade ores, ores with complex mineralogy we do not yet know how to process, and small deposits that are now uneconomical to mine and process. Other research activities focus on ways to reduce the Nation"s consumption of key minerals and increase the recycling of these minerals. The opportunities in this area include coal. The current middle eastern crisis reinforces the need for a stable energy supply--preferably a domestic supply. The extensive reserves of coal in this country are well documented. Perhaps what is not as well recognized is the impact that the price of coal can have on its competitive position both for domestic fuel selection considerations as well as for the ability of this country to compete in the coal export market. Today, the role to the United States is as a reliable, but high-cost exporter of high-quality coal. U.S. export coal competes with supplies from other major suppliers, including Australia, Canada, Poland. If U.S. mining costs were lowered by at least $8 per ton in the year 2000, then coal exports would surge by a projected 46 percent, and U.S steam coal displaces significant quantities of foreign coal imports in Europe. Further cost reductions would make

Jan 1, 1991

By V. R. Degner

Comments Summary It is very interesting to review the technical changes which have occurred in the industrial practice of minerals flotation over the past two decades. In 1972, worldwide industrial flotation was dominated by 'mechanical' flotation machines having an individual cell volume less than 500 cu.ft. Manufactures, such as DENVER Eqpt. Co., OUTOKUMPU, WEMCO, GALIGHER (AGITAIR), AKKER, and later DORR-OLIVER, produced flotation machines featuring a mechanical rotating impeller which served to mix pulp and air, prior to flotation, and to keep the solid ore particles in suspension. While sharing this common mechanical impeller feature, the machine design of the various manufactures differed in detail; particularly in regard to the vertical location of the impeller in the cell and the means by which flotation air was brought into contact with the pulp within the rotor mechanism. A review of the existing technical literature in 1972 would identify academic research studies, particularly at Columbia University (N. Arbiter, C, Harris ...) aimed at comparing flotation cell design concepts, of the various machine manufactures, on a hydrodynamic basis. These research studies were confined to very small, laboratory bench size, flotation machines, and the benefits of incorporating hydrodynamic considerations in the scale-up of the existing 300 cu.ft. mechanical flotation technology to larger cells was not commonly practiced industrially. Technological advances in minerals flotation, over the past two decades, have been influenced by a variety of economic factors including the increasing development of lower grade ore bodies, the attractions of producing a higher grade final concentrate, and the economy of tails retreatment to improve overall plant recovery performance, and flotation system “optimization" became increasingly important through the 1970-80 time period. The trend toward processing lower grade ores led to higher tonnage mill operations, and stimulated the development of the very large capacity mechanical flotation machine for roughing and scavenging duty. In 1972, the 500 cu.ft. size flotation machine was being pilot tested and introduced to the industrial market. Today, 1993, individual cell volumes of 1500-3000 cu.ft. are operating successfully throughout the world, and well planned plant test programs have concluded that the very large flotation machine can achieve the same metallurgical performance level of its smaller predecessor. The large flotation machine development record clearly credits the incorporation of internal cell hydrodynamic considerations in guiding the scale-up of the mechanical flotation machine to large sizes. This guidance eliminated, or reduced significantly, costly in-plant prototype machine changes which increase Dramatically with increasing flotation machine size. Early in the 1980's, at approximately the time that flotation machines in the 1500 cu.ft. class were being introduced into the market, it became evident that the availability of the very large mechanical flotation machine brought with it the need for a systematic means to "optimize" the flotation system by relating flotation cell size, row length (i.e. number of cells per row), and flotation rougher, scavenger, and cleaner system configuration to the economic objectives of the concentrators' operating management. Flotation system optimization consists of quantifying the flotation process performance using a suitable model which relates the kinetic response of the trace specie and the gangue material to the cell overflow, and produces a numerical relationship between product grade and value recovery. The computer analysis technique has proven to be an invaluable tool in determining the kinetic model coefficients which characterize a given application, and is also used to apply the resulting model to a proposed minerals beneficiation situation seeking to "optimize" the flotation system by relating metallurgical grade-recovery performance, flotation cell size, and circuit arrangement, to plant space, installation, and operating costs. It is interesting to note that these same computer based kinetic flotation analysis techniques can be easily applied to quantitatively evaluate the effect of different chemical reagent strategies, and flotation air transfer, on process performance for a variety of candidate feed ore types.

Jan 1, 1993

By J. R. Frederick

Introduction In response to industry needs and requests, Joy Mining Machinery is aggressively evolving a "game changing" system of underground development mining machinery. This entry-development system (EDS) project is concentrated on providing clean, protected and ergonomic operator areas and a quantum leap in productivity. To meet these goals, a virtually continuous and automated mining system is needed. Operators must be able to efficiently and ergonomically perform required functions from a protected environment. Health-related issues, such as respirable dust and noise, must also be addressed. A new concept system of integrated face equipment, from the continuous miner to and including advancing the section belt and services, is needed. Phase I of the project was aimed at developing the bolting technology required. Through acquisition of Cram Australia and joint development efforts with Canyon Fuel Co., Joy now has this capability. The test platform, known as the Joy Multibolter, has successfully completed its trials at Canyon Fuel's SUFCo Mine (Fig. 1). These tests validated the bolting technology and operator protection and ergonomic issues. Phase II includes the development and testing of an integrated mining machine (IMM) capable of advancing a heading 1.5 m (5 ft) while simultaneously cutting a fullface width (single pass) and installing a complete bolt pattern. The IMM, unveiled at MINExpo 2000, incorporates the bolting technology of the Multibolter with automated full-face cutting. This machine was designed to meet Joy's stringent health, operator protection and 300m/d (1,000-ft/d) productivity goals. Phases III through V will include development of processes and integrated haulage, ventilation, power, material handling and section services advancing equipment. Processes and equipment developed will be designed for seamless integration into a complete entry development system. The focus of this paper is the new continuous miner (IMM) development, proposed testing and expectations for the EDS. The IMM is scheduled for commissioning and trials beginning in April 2001 at the SUFCo Mine. SUFCo Mine Canyon Fuel Co. is jointly owned by Arch Western Resources and the Itochu Corp. of Japan. It owns and operates three coal mines in Utah: the SUFCo Mine in Sevier County, the Skyline Mine in Carbon and Emery Counties and the Dougout Canyon Mine in Carbon County. Incorporating state-of-the-art-mining technology and advanced mine management practices, the SUFCo Mine is one of the most efficient underground coal mines in the world. The SUFCo Mine is located approximately 50-km (30 miles) northeast of Salina, UT, in the Wasatch Plateau portion of the Uinta coal basin. The mine property consists of 9,900 hm2 (24,470 acres) with approximately 118 Mt (130 million st) of recoverable reserves. Public utilities and industrial concerns purchase approximately 95% of the coal mined at SUFCo through short- or long-term contracts. Coal reserves are extracted by longwall mining, and the panels are developed using continuous miners. The longwall face at SUFCo Mine is 283-m (930-ft) wide, and the seam height ranges from 2.4 to 4 m (8 to 13 ft). The two development sections are in full operation using Joy 12CM12 continuous miners. Two super longwall panels, under development in the northeast portion of the lease block, are 4,270-m (14,000-ft) long with a 283-m (930-ft) wide longwall face. Each panel contains approximately 5.4 Mt (6 million st) of recoverable coal. SUFCo has been a world leader in productivity for a

Jan 1, 2003

By Tim O’Neil

Until about three years ago, Asarco's copper business consisted predomi¬nantly of custom smelting of ores and concentrates produced by other mining companies. Since then, the company has been transforming itself into a fully integrated producer in copper mining, smelting, and refining. In doing this, Asarco has lowered its costs and restructured its operations and finances. Now, Asarco hopes to complete this process by spending $260 million over the next three years, to expand and modernize its copper facilities and boost production by some 40%. The capital spending program includes: • $130 million at the Ray mine about 113 km (70 miles) north of Tucson, AZ, to expand mining capacity and install an in-pit ore crusher, mill, and concentrator; • $100 million, to expand the mining capacity at the Mission Complex located south of Tucson, AZ, and refurbish the adjacent, idle Pima mill and concentrator. (Asarco had earlier exercised an option to purchase the Pima mill for about $6 million); and • $30 million, to modernize the copper smelter in El Paso, TX, with a new flash smelting process. The new program is in addition to a recently completed first-phase expansion of the Mission mine, mill, and concentrator. This $13 million debottlenecking of existing operations in¬creased production capacity by 46% or 24.5 kt/a (27,000 stpy), to 79 kt/a (87,000 stpy) of copper in concentrates. In addition, a previously an¬nounced $12 million expansion program at the Ray mine is scheduled for completion in early 1990. It will expand mill capacity, to offset the anticipated effects of increasing ore hardness as the pit deepens. Ray produces 68 kt/a (75,000 stpy) of copper in concen¬trates and an additional 36 kt/a (40,000 stpy) of electrowon copper. By 1992, when Asarco's expanded and modernized copper facilities are operating at capacity, the company's mine output will have increased by 67 kt/a (74,000 stpy), to 263 kt/a (290,000 stpy) of contained copper. That will be enough to provide all of the feed required for Asarco's two copper smelters - by then, both of them modern, state-of-the-art facilities. Asarco's expansion and modernization program will further reduce costs and provide added assurance that the company's copper business will be profitable at the bottom of the cycle, according to Chairman Richard de J. Osborne The Ray mine portion of the new program will include construction at the mine of a new mill and concentrator, with a capacity of 18 kt/d (20,000 stpd) of ore. These new semiautogenous grinding mills and large capacity flotation cells will augment the present 27.2 kt/d (30,000 stpd) concentrator located 29 km (18 miles) away, in Hayden, AZ. A 29 km (18 mile) pipeline will be built to carry tailings in slurry form from the new Ray mill to the present tailings pond. Concentrates from the new facility will be shipped by rail to Asarco's Hayden copper smelter. Ray's present 27.2 kt/d (30,000 stpd) crusher, adjacent to the open-pit, will be replaced by a 54.4 kt/d (60,000 stpd), portable in-pit crusher and conveying system. This will reduce the more expensive ore haulage by truck. The Ray project is scheduled for completion by 1992. It will increase the mine's annual output of copper in concentrates by an additional 33.5 kt/a (37,000 st), to 102 kt (112,000 st). And the project could mean an additional 400 jobs at the 730 employee Ray operation. Work at the Mission Complex involves reactivation of the Pima mill and concentrator and expansion of mine output sufficient to provide ore to both the Pima mill and the present Mission mill. In 1985, Asarco purchased the Pima mine, which occupies one end of the Mission pit. The work at Mission will increase its annual capacity by 33.5 kt (37,000 st), to 112 kt/a (124,000 st) of contained

Jan 1, 1989

By Werner Hofmann

INTRODUCTION The attempt to interprete lung cancer incidence caused by inhaled radon decay products in items of radiation dose raises the question of the relevant dose. The various dosimetric approaches published by now are characterized by an increasing complexity in the structure of the models used. Ranging from organ doses to microdosimetric specific energy distributions in the cells at risk, a significant trend from the macroscopic to the microscopic scale can be observed. Since tumors originate preferentially in the basal cells of the lobar and segmental bronchial epithelium, these cells are regarded as the critical target for inhalation carcinogenesis. The evaluation of basal cell doses is, therefore, the main objective of lung dose assessments. Various dosimetric models have been published in the past (Altshuler, Nelson and Kuschner, 1964; Haque and Collinson, 1967; Harley and Pasternack, 1972; Hofmann, Steinhäusler and Pohl, 1979, 1980; Jacobi, 1964; Jacobi and Eisfeld, 1980; James , Greenhalge and Birchall, 1980). Due to incertainties of physical and biological parameters involved and the application of different anatomical and physiological models the claculated doses are varying up to one order of mangitude. Independent of the choice of these dosimetric models applied to the calculation of lung doses, deposition, clearance and resulting dose are affected essentially by the properties of the inhaled aerosol as well as by personal characteristics. Both the properties of the exposed individual as well as of the inhaled environmental atmosphere have to be considered in radiation protection. It is the main objective of this paper to illustrate the influence of both parameter sets on basal cell doses by varying the above parameters. PERSONAL CHARACTERISTICS Though it might be more convenient for radiation protection calculations, the biological "man" cannot be represented by a uniform standard man. In Tab. 1 these personal characteristics which cause the variability of man are listed together with the region of their effectiveness. In the following the influence of these parameters will be discussed with regard to lung dose assessments. Besides these factors the great biological variability of all anatomical and physiological parameters involved as well as pathological alterations due to lung diseases cause additional variations in lung dosimetry. [ ] Age Age can be considered as the most important personal factor influencing the anatomical structure of the lung between birth and about 15 years of life. This period is characterized not only by an enlargement of already existing respiratory units but also by structural changes. Besides these anatomical alterations deposition is strongly dependent also on respiration parameters, such as tidal volume (TV) and respiratory frequency (RF). Whereas RF decreases with progressing age in an exponential manner, TV increases significantly resulting finally in a growth of the respiratory minute volume (RMV). Also mucus clearance in the infant might be more effective than in the adult, though no reliable experimental data are available. Superposing all these age-dependent changes mean basal cell doses are higher for children by about a factor of 2 than for adults living in the same radioactive environment (Hofmann, 1981). In the adult the following alterations of respiration standards with age are reported: total lung capacity diminishes with age, functional residual capacity is unchanged or increases with age and the dead space rises slightly with age (ICRP, 1975). The influence of these lung capacities on deposition, however, can be regarded as insignificant. Due to the ageing process mucus velocities my be considerably smaller in older people. This effect can also be superposed by the simultaneous influence of ciliatoxic effects of cigarette smoke and air pollutants or other bronchial diseases. Since the lower age limit for occupational exposure is about 18 years, age can be disregarded in the uranium mining industry for the determination of radiation doses, though lung cancer induction is significantly dependent on age.

Jan 1, 1981

By E. Topuz

The objective of mine ventilation is to provide suitable environmental conditions in working places at an economical cost. Maintaining a stable air flow, i.e., a flow quantity and the direction, is of vital importance. In practice, however, air flow quantity in underground openings varies continuously. Therefore, the stability of air flow means relative stability that is the flow in a branch moves along a certain direction while the variation in air quantity stays within acceptable limits. Many underground mines have low stability of mine air flow because almost all types of ventilation systems involve complex diagonal branches through which air flow quantity and, more importantly, the air flow direction may change easily. This creates extremely hazardous, unstable conditions, especially during emergencies. This paper deals with the directional stability of air flows in underground mines in single or multiple fan systems. It examines the rules of directional changes of air flows in diagonal branches, and proposes a method of calculating the stability conditions. It provides a criterion that may be used in designing new mine ventilation systems to ensure a desired degree of stability or in improving the existing systems.

Jan 1, 1986

By H. Keith Henson

The purpose of this paper is to describe the possible application of two relatively new technologies: flat load cells, and improvement seeking computer programs (referred to in the literature as heuristic programs); to a very old problem, inventors control of ball mills. The combination of these two technologies seems most applicable to grate discharge mills operated closed circuit. It is possible that other applications such as controlling the inventory of autogeneous mills might also be found. Direct control of ball mill inventory has been the goal of a number of investigators over many years. Many patents and articles on the subject have claimed success, but operating installations are hard to locate. An excellent review of the advantages and problems of direct inventory control is contained in an article by Oswald and Ziegler (1). Figure 1 is a conventional representation of throughput vs. inventory with other factors such as slurry consistency and rock twee held constant. There are common sense, physical arguments? and experimental evidence supporting the existence of a unimodel curve of this twee? though direct measurement of the shape is difficult and how it moves as rock type changes is riot well known. Figure 2 represents the problem faced by all mass measurements of inventory, a tare weight of about 25 time the inventory mass. Worse yet, the tare is variable due to ball and liner wear and the Periodic addition of balls. The problem then breaks down into two parts: 1) obtaining enough mass

Jan 1, 1977

By E. Jong, E. Watkins

"The application of passive tracer gas sources in underground mines is particularly useful for long-term tracer gas studies, as well as for studies in permissible areas of underground coal mines. The use of passive perfluoromethylcyclohexane (PMCH) sources have previously been demonstrated in mines, but this new work details the development and testing of multiple, distinct tracer compounds that can be used in passive sources. A description of their potential application in mine ventilation systems is also provided. Three tracer compounds are detailed, which are PMCH, PECH and PMCP. The release rates of these tracers were examined over a 180 day period at multiple temperatures. The advantages and disadvantages of these sources are presented, along with potential applications in understanding complicated ventilation circuits, flow through gob, and leakage. INTRODUCTION The use tracer gases for ventilation applications is an established practice, with various research projects being perform with Sulfur Hexafluoride (????6) in the past. Perfluorocarbon tracers (PFTs) however are relatively new compared to ????6, which is proven to be useful in ventilation and air modeling experiments along with other PFTs (Watson, Wilke, Dietz, Heiser, & Kalb, 2007). These liquid tracers are characterized by low background presence in air, inert behavior with other gases, high detectability with a gas chromatograph and low toxicity. A design was proposed called a permeation plug release vessel (PPRV), which initially introduced by Brookhaven National Laboratory to meet those requirements. The PPRV works by allowing the gaseous form of the tracer to diffuse through the permeable silicone stopper and evaporate into the open air on the other side. The PFTs inside the vessels are injected as a liquid but instantly begin to convert to their gaseous phases at room temperature due to high vapor pressures (Zhang, H., Cloud, A.,2006). Previous studies have detailed how release rates change based on plug thickness across various temperatures (Jong et al., 2015), but not on the release rate stability based on temperature across multiple tracers. For use in underground mines passive release sources need to be durable, be simple to manufacture, have customizable and reliable release rates as well as a long operating life. The PPRV vessel provides a steady release of tracer gas that is essential for long term passive release experiments, making it a viable vessel for the PFTs being tested. The PPRV design also allows for vessels to be bundled together to achieve release rates at detectable levels and allows for the capability to run ventilation surveys with multiple tracers simultaneously. The ability to conduct ventilation surveys with multiple tracers using the PPRV bundling design and detection of the PFTs makes testing the tracers and design together a promising potential for complex and long term mine ventilations studies."

Jan 1, 2017

By K. V. Raj, A. T. Weakley, A. L. Miller, D. A. Parks

Diesel particulate matter (DPM) is a common and well-known health hazard in the mining environment. The current approved method for monitoring both the organic and elemental carbon (OC, EC) portions of DPM is a laboratory method with a turnaround time of approximately one week. In order to evaluate exposure levels and take corrective action before overexposures occur, a portable real-time device capable of quantifying both OC and EC is needed. To that end, researchers from the National Institute for Occupational Safety and Health (NIOSH) designed and tested a device based on narrow bandpass optical filters that is capable of targeting infrared absorbance bands associated with DPM. Five optical bandpass filters were chosen based on previous work quantifying DPM using Fourier-transform infrared (FT-IR) spectrometry. The resulting device, referred to as a filtometer, is optimized to exclusively determine DPM and could serve as a cost-effective, field-portable alternative to laboratory-grade FT-IR analysis and instrumentation. The performance of the filtometer was investigated by calibrating FT-IR data from DPM (dependent variable) to the filtometer spectra (predictor variables) using a partial leastsquares (PLS) and ordinary least squares (OLS) approach. The square of the correlation coefficient and root-mean-square error of cross validation m

Mar 2, 2022

By R. Hogg

Sedimentation in highly flocculated suspensions of fine particles such as clays occurs through individual settling units (flocs) which have very open structures and correspondingly low density -typically less than 5% solids by volume. It follows that such settling processes rapidly lead to the build-up of a bed of flocs which are essentially close-packed, with inter-floc porosity of perhaps 50%, but with an overall solids content of no more than about 2-3 percent by volume. An important consequence is that the thickening process is dominated by the consolidation of this bed rather than by simple settling of the individual flocs. Experimental measurements of sediment consolidation in flocculated clay suspensions indicate that for a given system, consolidation rates are essentially determined by solids concentration and can be evaluated using the classical Kynch treatment. However, these rates are strongly dependent on the physical as well as chemical conditions of the flocculation process. Furthermore the extent to which gravity consolidation proceeds depends on the total weight of sediment (i.e. on both height and solids concentration). The implications with respect to thickener operation and the requirements for laboratory testing for thickener design are discussed.

Jan 1, 1992

By J. D. Miller

Certain bituminous coals of recent geological age are known to contain a significant quantity of natural (fossil or subfossil) resin. Such resinous coals are found in the western U.S., particularly the Wasatch Plateau coal field in Utah. Some of the seams in this field contain approximately 5% resin which has been recovered by gravity and/or flotation processes since 1929. Resin concentrates thus produced are of low quality and are usually refined by solvent extraction and precipitation. The purified resins are of commercial importance, being used in the adhesive, varnish, enamel and ink industries, etc: Recently, an improved flotation technique has been developed which involves ozone conditioning to selectively float resin from such coals. In this flotation process, a concentrate product which contains 95% resin at a recovery of 80% can be obtained in a single stage from coal containing approximately 10% resin, whereas conventional flotation at a similar level of recovery produces a concentrate having a resin content of 30-40%. Economic analysis shows that the ozone flotation process has good potential for use by industry.

Jan 1, 1988

By K. A. Eriksson

Over 25 years ago, SKEGA pioneered the use of rubber linings in grinding mills and rubber is today widely accepted and almost standard material chosen for Regrind -and Secondary Mills. There are, however, only a few Primary Mills in operation with "solid" rubber linings because available materials and designs are often not cost efficient in comparison with steel alloys on a cost per ton basis and/or downtime for liner replacement would be too high.

Jan 1, 1988

By B. A. Hancock

It is not at all surprising that causticized potato and potato derived amylopectin starch solutions performed much better than their parent starches. Some preparation is required to rupture the starch granules to effect the polymeric adsorption and interparticle bridging necessary for selective flocculation. In laboratory work comparing the deslime performance of causticized and autoclave cooked laboratory corn starch solution preparations, it was found that higher deslime weight rejections, with attendant proportionally greater iron unit losses, occurred with the causticized starch. These results may be specific to the ore involved but they do suggest that cooking and causticizing cause different starch granule rup- ture and/or starch breakdown, which have an effect on desliming response. I calculated from the data in the article that the slimes product grades were high - 24.3% and 20.3% Fe when 53.7% and 54.5% Fe concentrate products were obtained, respectively, in Table 4, and 21% Fe with a 62.6% Fe concentrate in Table 5 - using the natural tailings sample, which had a head of 34.3% Fe. It may be advisable for the authors to consider different starch preparations in future investigations. The combination of upgrading and selectivity results presented in Table 4 are not as good as the authors suggest. The authors' claim that a system has been developed to produce saleable concentrates from the Kudremukh tailings is quite disconcerting. There are many hurdles yet to be crossed before commercial application of selective flocculation becomes possible because differ- ences between the very small-scale laboratory tests conducted and commercial application are rather large. Among the many differences are varying circuit feed grades that will occur from use of tailings, the apparent face that much lower tailings grades will be encountered in practice (it is much easier to achieve a high concentrate grade with reasonable recoveries using 34.3% Fe tailings as in the study rather than 25.3% Fe tailings grades that the plant apparently averages), the hydraulic nature of the thickeners used in operations compared to the static system used in laboratory tests, the different size distributions that will be obtained from a plant closed grinding- classification circuit, and differences in water used in a plant operation and the laboratory. The authors wrote that it was necessary to overgrind to be sure that the coarse gangue would not settle with the iron oxide floccules. This situation is likely to be exaggerated in commercial operations where it is assumed cyclones would be used for classification. Because cyclone classification is greatly influenced by particle densities, there will probably be an even greater difference in size between the iron and gangue particles in the plant, which would make the gangue slightly coarser still in relation to the iron. This would make the selective flocculation-desliming separations using the procedure employed by the authors even more difficult and, using the dispersant system the authors employed, greater overgrinding would be required. To grind finer to minimize the coarse gangue in the flocculated iron oxides is quite inefficient and appears not to broach the problem. The actual problem appears to be insufficient dispersion of the ground pulp. In this situation, addition of a dispersant would likely be required to attain a sufficiently high pulp dispersion level to efficiently effect a selective flocculation-desliming separation. Although the very coarse particles would still have a tendency to settle with the floccules, it probably would be found unnecessary to overgrind as much as indicated. Use of an optimum combination of dispersant and pH modifying reagents may also significantly improve the selectivity of desliming. Additionally, although it is possible that sufficient dispersion may be obtained by pH control alone in some situations, it is quite probable that added dispersity was obtained in the reported work from using distilled water. It is research experience that distilled water enhances dispersion. In commercial operations it may not be expected that sufficient dispersion will be obtained by pH control alone, unless the water used in the process is by nature quite dispersive. Overall, a change in the Kudremukh tailings dispersant scheme appears necessary where a dispersant is used in conjunction with a pH modifying reagent. With this change, different dispersion-flocculation responses will result that would have to be further evaluated. Therefore, it is still an open question whether an efficient and effective selective floccula- tion separation using Kudremukh tailings may be obtained that will produce saleable concentrates.

Jan 1, 1987

By Loic Galisson

"Urban tunneling projects are usually extensively monitored. Most of the instruments used rely on benchmarks providing a sustainable datum throughout the life of the project. The monitoring program also is based on a predicted model of deformation induced by specific construction methods. Events can interfere with those assumptions and eventually alter the stability of these datum. In addition, the anticipated ground conditions and hence the theoretical deformation model often differ from reality. Satellite Radar Interferometry provides useful information to overcome the weakness of the hypothesis made before construction. It is also a powerful tool to ensure the continuity of the monitoring program throughout the life of the project, accurately describing the true effect of the project on the surrounding environment. This paper emphasizes the benefits and limitations of this technique for urban tunneling applications, illustrated by examples of major tunneling projects around the world. MONITORING URBAN TUNNEL PROJECTS Why Monitoring? Retrofitting existing tunnels or constructing new tunnels – including access and retrieval shafts, portals and cross passages – implies an alteration of the neighboring soil structure. Excavating, dewatering, grouting, loading tie backs, etc. artificially modifies the natural equilibrium of the pore-water pressure, of the water table level and of soil stability. In many cases, the effects are immediate: ground loss, deformation of utilities, settlements of buildings, and distortion of infrastructure are a few examples resulting from construction activity.Instrumentation and Monitoring Scope To control and mitigate the risks of damage associated with the above effects, tunnel projects usually include an instrumentation and monitoring program. Depending on the level of geotechnical, structural and environmental risk, the magnitude of this program varies. Projects with a low exposure to risk may restrain the program to conventional methods such as limited topographical surveys and intermittent manual readings of geotechnical instruments. On the other hand, iconic projects with high risk or with controversial history may implement complex and extensive instrumentation plans, involving highly technical solutions such as Automated Motorized Total Stations (AMTS – see opposite Picture 1), Multi-Point Borehole Extensometers (MPBX), In-Place Inclinometers (IPI) and a wide series of fully automated geotechnical, structural and environmental sensors. In this case, all the devices are usually connected to field data loggers collecting raw data around the clock at frequencies ranging from days to seconds, depending on the sensors."

Jan 1, 2016

By K. V. Raj, A. Miller

"Workers at mineral processing facilities are often exposed to high levels of dust generated when ores are processed. Crushing, grinding, screening, and other processes generate large quantities of dust, which can exceed the threshold VALUES (prescribed by the Mine Safety and Health Administration (MSHA). Many ores contain quartz (silica), which has been known to cause serious health problems in workers over time. Given the structure of mineral processing plants, the airflow regime is not coherent inside the building, which may lead to multiple recirculation zones. These recirculation zones can trap dust, and concentrations of dust can then rise over time. Therefore, there is a need to understand the airflow phenomenon that occur inside of mineral processing facilities and how these occurrences interact with the dust generation processes to identify zones of potentially high dust concentration. Computational fluid dynamics (CFD) modeling can give a better understanding of the airflow and help recommend designs and methods to mitigate the high dust concentrations in a mineral processing plant. This paper presents the CFD modeling of airflow inside of a mill building to demonstrate airflow patterns that will affect the generation and subsequent dispersion of dust due to crushing, grinding, and other activities. This study was conducted by researchers from the National Institute for Occupational Safety and Health (NIOSH). INTRODUCTION In a mineral processing facility, minerals go through various mechanical processes in order to reduce their size for separation of economic minerals from gangue minerals to produce a final marketable product. This research, conducted by the National Institute for Occupational Safety and Health (NIOSH), focuses on ore mills in metal and nonmetal mining (MNM) operations, but the applicability of the approach will be valid for any large structure where workers are exposed to airborne contaminants. The processes of crushing, grinding, cleaning, drying, and product sizing in these facilities generate a large amount of dust, creating hazardous conditions for the workers in these facilities. This is highlighted by the fact that MSHA sampling data for the years 1997–2012 indicate that 12.3% and 15.9% of the gathered samples were over 100 µg/m3 for silica for metal and nonmetal mills, respectively [1]. Mineral processing operations typically use some type of engineering control to address their most significant dust sources. Engineering controls include such approaches as bag-house-type dust collectors, scrubbers, and electrostatic precipitation [2]."

Jan 1, 2018