Search Documents

By Barry K. Johnston, Norman W. Bainbridge, Neville C. Lockhart

CSIRO and its collaborators have developed a major R & D project on dewatering of coal. This involves sub-projects on (i) the fundamentals of coal-water associations; (ii) reducing the variability of product moisture levels from small coal centrifuges; (iii) process mechanisms and optimisation for fine coal dewatering; (iv) pilot scale testing, engineering development and innovation. Results from each of these sub-projects are presented, and the pilot facility incorporating a vacuum filter, belt press, membrane press, hyperbaric filters and centrifuges, is discussed. The vacuum filter and membrane press can be configured for electric-field assisted dewatering, which provides substantial enhancements in the rate and degree of dewatering for fine coal, coal tailings, and other suspensions.

Jan 1, 1995

By Shailesh K. Patel, Shaaban Ben-Poorat

In order to ascertain the environmental fate of flotation reagents (fatty acids, fuel oils, and amines) associated with phosphate rock processing with confidence, it was necessary to first establish laboratory methodologies to identify and quantify flotation reagents. This approach was necessitated by the fact that the reagents used in the flotation process are either reclaimed or by-products of other industries and is dictated by their cost. Initially, several blind performance evaluation samples were prepared by spiking water samples with known amounts of either single reagents or reagent mixes and then analyzed. Reagent recovery for the blind performance evaluation samples was within acceptable limits for similar compounds established by the US Environmental Protection Agency. Averification process involving the use of standards and the refinement of analytical methods was utilized to develop standard operat- ing procedures (SOPS) and method detection limits (MDLs) specific to the identification and quantification of the flotation reagents used in the phosphate industry. These procedures and MDLs were critical to support the project's primary goal of assessing the fate of selected flotation reagents in the environment.

Jan 1, 1999

By Prakash M. . P. E. Donde

1. INTRODUCTION The Washington Metropolitan Area Transit Authority (WMATA) has often taken a leading role in introducing innovative construction technologies to build its transit system. Most recently, Contract Section E-5a, which included Fort Totten Station and Tunnels was constructed utilizing the New Austrian Tunneling Method (NATM) in soft ground. Along with the station and tunnels, two permanent shafts were also constructed in soft ground employing the NATM technique. This project is located within the District of Columbia on the Greenbelt Route. The subject of this paper is to discuss the unique method of construction of these two shafts, and explore the benefits of applying the NATM technique to the construction of deep shafts. The design of the shafts was performed jointly by Jenny Engineering Corporation of Springfield, New Jersey, and Mayreder Consult of Linz, Austria. The designers also provided construction support services and a resident NATM expert at the site during construction. The construction of the project started in April 1988 by a joint venture of Mergentime Corporation and H. T. Construction, a subsidiary of Hochtief Company from Germany. This $48.7 million construction project has been completed. 2. SUBSURFACE CONDITIONS The two NATM shafts are located primarily in Cretaceous-age deposits that are over 100 million years old. These deposits are intermixed and lenticular in nature

Jan 1, 1993

By J. A. Reizes, C. A. J. Fletcher, T. Jancar

Spirals play an important role in fine coal and mineral processing. To date, almost all spiral designs have been empirically based. Although many operational units have evolved utilising this approach, it does not necessarily lead to optimal spiral designs. This paper presents the preliminary results of a collaborative computational and experimental research program to understand the detailed separation process which will ultimately lead to a parametric assessment of alternative spiral designs through computational simulation. Unlike the empirical approach, a computational simulation is only subject to the fundamental physics of the fluid flow. No prior knowledge of the generic spiral flow is necessary. The computer code implements a robust finite volume technique to predict the three dimensional fluid motion. A height function method is used to model free surfaces and the code is capable of handling arbitrary spiral geometries. Preliminary validation of the computational simulation is carried out through analysis of an existing spiral design -the Mineral Technologies LD9 unit. Computational flow predictions are compared with experimental measurements obtained using a number of techniques, including sampling and flow visualisation, for flow test cases where no solid particulate is present.

Jan 1, 1995

By Dirk van Zyl, Clint Strachan

A study was conducted to assess the feaeibility of increasing the heap height above one lift at the Alligator Ridge Mine. This study concentrated on the physical aspects of the heap and liner performance. Two principle aspects were addressed during this investigation: (a) the adequacy of heap permeability under present and future loading conditions; and (b) the adequacy of the liner to limit seepage losses. Field and laboratory test a were performed and their details and results are presented. It was concluded that the permeability of the heap would remain adequate for higher heap. The geometry of the heap will be the major constraint. It was also concluded that the liner would perform satisfactorily beneath higher heap.

Jan 1, 1987

By P. L. Stavenger

Principles of Operation and Mechanical Features General Mechanical Description Sieve-bend screens are high-capacity screening devices which utilize stationary, concave, wedge-bar screening surfaces. A complete sieve bend is comprised of a feed distribution chamber, a structure for holding the screen surface, and collection chambers or chutes for oversize and undersize materials. In devices used for metallurgical practice, provision is usually made for reversal of the direction of flow over the surface, either by rotating the surface or by changing the feed nozzle position. The size of the unit varies in height from 5 to 8 ft, and in width from 2 to 8 ft. The orientation of the wedge-bar surface is such that the slots between the wedge bars are perpendicular to the flow of feed material over the surface. The feed distribution means is arranged such that the flow of liquid suspension is distributed evenly and tangentially over the width of the screen surface. A variety of means are used including simple gravity weir feeds, long slotted nozzles, and a multiplicity of round nozzles. A typical gravity-fed weir type nozzle is shown in Fig. 18. Most sieve bends are fed with gravity feed in such

Jan 1, 1985

By Daniel Hodouin, Claude Bazin, Sami Makni

SCOTT COULTER: Thanks, Eric. Thank you all for coming. Our first speaker today is Claude Bazin. Claude received a degree in metallurgical engineering in 1980 from Laval University in Quebec. He worked for a short time in a mineral processing plant and then returned to Laval to complete graduate studies in the field of process modeling and control. He obtained his master's degree in 1983 and his Ph.D. in 1990. In 1987 he joined Brunswick Mining, New Brunswick, as research metallurgist and subsequently process control engineer. In 1990 he joined Helzfield Mines, New Brunswick, as senior metallurgist. In 1991 he accepted a position of professor at the department of mining and metallurgy at Laval University, a position he is still holding. He's a member of the CIM, TMS, and the Society for Mining, Metallurgy, and Exploration. Claude's topic today is "On-Line Material Balance for Flotation Plants." INTRODUCTION CLAUDE BAZIN: During the last two decades, the on-stream analyzer (OSA) has gained the stat& of key instrument for the control of flotation plants. The OSA is currently used in almost every sulphide flotation plant (Leroux and Franklin 1994), and its application to oxide mineral flotation plants is increasing. The OSA assays are sent to the flotation operators via an operator console or to control loops of various degrees of complexity (McKee 1991) implemented in a distributed control system (DCS). Operators and/or controllers take control actions based on these assays to ensure an adequate operation of the plant. Although this application pays off very rapidly for the purchase of the OSA, one could ask, "Could we get more from the OSA?" Some plants reported the use of OSA measurements for process optimization (McKee 1991). The optimization strategy is based upon economic indices calculated from metal recovery using the 2-product formula (Wills 1992, p. 124). The 2-product formula is sensitive to measurement errors in the assays and can lead to considerable scatter in the calculated indices (Hodouin et al. 1993). Least squares algorithms provide a robust alternative to filter out measurement errors (Spring 1992). This paper presents some applications of a recursive least squares algorithm that provides real-time estimates of the mass flow rates within a flotation plant using OSA and mass flow rate measurements.

Jan 1, 1998

By Arol, A. I., I. Iwasaki

The presence of calcium ion in iron ore pulps causes heterocoagulation of rnontmorillonite on hematite leading to indiscriminate dispersion. Two methods were investigated to control the adverse effect of montmorillonite: a chemical method using such complexing agents as EDTA and sodium tripoly- phosphate, and a mechanical method involving ultra- sonic treatment. Their roles in controlling the adverse effect were investigated by zeta potential measurements, starch adsorption tests, and flocculation and selective flocculation tests.

Jan 1, 1988

By Takashi Sakaguchi, Takehiko Tsuruta, Akira Nakajima

Some attempts were made to recover gold from aqueous systems using immobilized persimmon tannin. This adsorbent adsorbed gold from solutions containing hydrogen tetrachloroaurate (III) with high efficiency, whereas there was minimal adsorption from solutions containing gold (I) sodium thiomalate and sodium dicyanoaurate (I). The adsorption of gold was rapid, and was affected by the pH of the solution, temperature, external gold concentration and amount of adsorbent. Adsorbed gold was easily desorbed with 1 M thiourea solution, indicating that immobilized persimmon tannin can be repeatedly re-used for the recovery of gold using adsorption-desorption cycles.

Jan 1, 1995

By Fathi Habashi

CLAYS CONTAIN the mineral kaolinite, a hydrated aluminum silicate. It is an important potential raw material for aluminum, especially for those countries possessing no bauxite deposits. Therefore, there is no surprise to find a large volume of research done for the recovery of aluminum from clays. Kaolinite (Al203?2 SiO2?H20) contains 39.8% A1203; 46.3 % SiO2, and 12.9 % H2O. The analysis of a good-quality dried clay of an Eastern Canadian siliceous shale is shown in Table 8-1.

Jan 1, 1970

By Charles L. Kimbell

In 1989, worldwide total mineral industry activity registered advances from 1988. The advances may not have been as noteworthy as in 1988, but they can be regarded as a worthy theme for this article. The momentous political events throughout the centrally planned economy world had only a modest impact on actual 1989 industry performance. But these events have such potential for worldwide changes in economic activity in future years that they dwarf the actual happenings of 1989 in the minerals industry. Perhaps most significant factor here is the rapidity with which these changes have occurred. The end of World War II saw the almost immediate division of the world into major economic blocs. Since then, mineral industry activities and other industrial operations have been governed, to a considerable extent, by this partitioning. The developed market economy nations have operated as a group, the centrally planned economy states as another group. And these two groups essentially have vied for recognition in mineral industry operations in the developing economy states of Asia, Africa, and Latin America. The boundaries of these country blocs were fixed in the late 1940s and early 1950s. They were not markedly altered in the ensuing 40 years. We have seen the establishment of the Organization of Petroleum Exporting Countries, the continued Arab-Israeli confrontations in the Near East, the upheavals surrounding the rise of Moslem Fundamentalism in Iran, and the establishment of Soviet-oriented governments in Cuba and Nicaragua. These events have had notable effects on the world economy. But they have done little to change the pattern of market economy states functioning as a competitive bloc with the centrally-planned economy countries.

Jan 1, 1990

By A. E. Ketler

Powerful, yet inexpensive, personal computers running Windows-95 operating systems provide powerful mine-wide monitoring capabilities when properly engineered. Long awaited conductivity over LAN, phone and Internet links provide new dimensions for sharing information throughout an operator's organization, in- deed around the world. On-line data analysis, archival data storage and historical trend viewing generate shared inputs to production, safety and maintenance personnel. Five years in development, Rel-Tek's new EZ-Trol/W-DX system was engineered around the pilfalls of a Windows environment. It now offers higher speeds, 3D animated graphics and long distance telemetry - all with better reliability than ever before possible. The ubiquitous DDS utility inherent in most Windows was discarded in favor of a lightning fast RAM format. Several ponderous interpretive programs were redesigned into a single compiled entity, thus avoiding the overhead from message conversion, handshaking and transfer. To make the system user friendly, a 'Wizard" utility helps operators set up and reconfigure their systems on site. In-mine data acquisition telemetry was also re- vamped, incorporating a unique noise avoidance scheme, dubbed the "DX" bus - enabling longer distances and higher reliability. 12- bit analog conversion provides the enhanced resolution needed for field scaling auto-cal sensors. By mid '96, eight EZ-TROLMI- DX systems were up and running, several for more than a year. Factory updating and assistance are possible over a phone or Internet link. Our factory testing of components routinely includes actual operation at 2400 BAUD over 14 miles of twisted pair wires.

Jan 1, 1997

By Daryl R. Tweeton

The Bureau of Mines has developed PC-based tomographic computer programs for geophysical applications, and is making them available to potential users as part of a Bureau plan to facilitate the transfer of technology to industry. These programs were initially developed for predicting and monitoring the flow pattern of leach solution during in situ mining. Seismic crosshole tomography has located fractured zones of low seismic velocity and saturated zones of high seismic velocit above the natural water table. The Bureau has applied tomography also to assessing high-wall blast damage, and examining the integrity of mine-related geological structures. The tomographic programs include the straight ray pro ram BOMTOM (Bureau of Mines Tomography? and the program BOMCRATR (Bureau of Mines Curved Ray Tomographic Reconstruction) that can be run with either curved or straight rays. Both programs provide optional mathematical constraints to help counteract the nonuniqueness of reconstructions that occurs with crosshole data. They are available from the Bureau free of charge. With typical data sets, they can be run on a 386 microcomputer with 640 Kb RAM. BOMTOM was described in the Bureau Report of Investigations 9159, so this report emphasizes BOMCRATR. Curved and straight ray reconstructions using seismic field data collected while simulating injection of leach solution were compared. The curved and straight ray tomograms were quite similar even with velocity variations of more than 50 percent.

Jan 1, 1992

By J. A. Hrabik

The feasibility of mining deep phosphate deposits by a borehole mining system was compared with mining by proven conventional techniques. An economic comparison of the borehole mining system with conventional dragline and bucket wheel excavator mining systems was completed at various mining depths and production rates. Hypothetical phosphate deposits, with various overburden thicknesses and reserve tonnages, were defined. Geologic conditions necessary for the application of the borehole system were identified. Discounted cash flow analyses based on derived capital and operating costs were used to generate rates of return and product prices. Borehole mining was found to be more economical where overburden thickness was 46 m (150 ft) or greater. However, at 15- and 30-m (50- and 100-ft) thicknesses, conventional surface mining was more economical. Overburden thickness has a great effect on the economic feasibility of the conventional mining systems but less effect on the economics of borehole mining. Economies of scale are only realized in conventional mining, since larger equipment is used to achieve greater production, whereas increased production from borehole mining is achieved using additional equipment units. A comparison of the environmental effects of borehole and conventional surface mining systems showed that borehole mining is environmentally more desirable.

Jan 1, 1987

By W. M. Ma, Daniel W. H. Su, K. Centofanti, Yi Luo, W. L. Zhong, Syd S. Peng

3.1 INTRODUCTION The final subsidence basin discussed so far is that developed long after mining has stopped. In a supercritical final subsidence basin, the central portion subsides uniformly. Thus any structures located there are not subjected to any final permanent surface deformation. But this statement is only true for the final subsidence basin. When the face is moving, the structures are subjected to dynamic deformations associated with the dynamic subsidence basin. For instance the house in front of a moving face (location 1 in Fig. 3.1) is subjected to the maximum tensile strain and the maximum positive curvahue. When it falls behind the face in location 2, it is subjected to the maximum compressive strain and the maximum negative curvature. When the house is far behind the face in location 3, it returns to its original condition with only uniform subsidence. However, the magnitude of the dynamic deformations may be sufficiently large to damage a structure in locations 1 and 2 before it reaches location 3. Therefore it is very important to study the characteristics of the dynamic subsidence basin. Under normal conditions, when the face has advanced for a distance approximately one-sixth to one-third of the seam depth from the setup entry, depending on the seam depth and the physical properties of the overburden strata, the movement of the over- burden strata reaches the surface, whereupon the surface also be- gins to deform. Thereafter, the surface point where the movement initiates is always located at a fixed distance ahead of the face. The angle between the vertical line at the faceline and the line connecting the movement initiation point on the surface and the face- line is the angle of advance influence, w. The angle of advance influence can be used to determine the distance, [ 1], which is the influence zone ahead of the face. w is approximately 20O to 35 O for the northern Appalachian coalfield (Peng and Geng, 1984). The movement of each surface point is a relatively complicated process both in time and in space, because the relative position between the faceline and each surface point varies continuously, so that the direction and rate of movement for each surface point differ. In the following sections, the movements of each surface point on the major cross section are illustrated. 3.2 DYNAMIC SURFACE MOVEMENTS Dynamic surface movements include dynamic subsidence and displacement. The movement of each point on the subsidence basin is different as the face advances from 1 to 6 (Fig. 3.2). Surface points A and B, being far in front of the moving face, subside and displace toward the face (i.e., from A to A' and from B to B'). Point C, which is quite near but in front of the moving face, subsides continuously but displaces initially toward the face and then turns to pure subsidence ending up at C'. Point D, which is behind the face above the gob, subsides continuously, but displaces initially toward the face when it is in front of the face and reverses to follow the moving face when it is behind the face, with the amount of displacement toward the face being larger than that following the face. As a result the net displacement is toward the center of the gob (i.e., from point D to D'). The same statement is true for point E. For point F, the net displacement is zero, i.e it appears to have dropped down vertically to F'. For points G to I, the net displacements are in the direction of face advance except the magnitudes are increasing in sequential order. Point 1, has reached the final dynamic position of 1'. In other words, the face has passed sufficiently away such that it does not affect the movement at point I. All other points (A to H) are still within the face influenced area. 3.3 DEVELOPMENT OF DYNAMIC SUBSIDENCE PROFILES When the face has moved for a distance of h/6-h/3 from the setup entry, surface subsidence reaches the surface. At this time the surface subsidence basin is very mild (S, in Fig. 3.3), and it is symmetrical about the center. As the face continues to advance, the maximum subsidence continues to increase, and its location moves with, but falls farther behind the face. When the face has advanced a sufficient distance, e.g., (0.9-2.2)h, away from the setup entry, the maximum subsidence reaches the maximum possible value (curve S,). At this time, the dynamic subsidence profile is fully developed. Thereafter both sides of the dynamic subsidence profile become stabilized. The subsidence profile on the face side moves with the advancing face in an orderly manner (curves S, and S,). When the face stops, the face side of the profile continues to subside and becomes stabilized (curves;) sometime after. Curve S; is the final subsidence profile (see Fig. 2.22). 3.4 DEVELOPMENT OF DYNAMIC DISPLACEMENT AND SLOPE PROFILES The dynamic displacement profile moves with the advancing face (Fig. 3.4), but changes according to some specific rules. When the face has advanced to A, the surface begins to move and its dynamic displacement profile has two maximum values (curve Ua): one positive near the setup entry moving toward the face advancing direction and the other negative on the face side also moving toward the face advancing direction. As the face continues to advance, the positive maximum displacement on the setup entry side increases and moves toward the face continuously. The same statement is true for the negative maximum displacement on the face side. When the opening increases to the critical size, both the maximum positive and negative displacements reach the peak values and remain constant thereafter. Notice that when the opening becomes critical in size, the point of zero displacement no longer moves with the advancing face. Rather it spreads into an area of zero displacement (curve Ue) and expands as the face advances. When the face stops, the displacement on the face side continues until it becomes stabilized (curve Úe). Curve Úe is the final displacement profile. The ratio of maximum dynamic to final displacement ranges from 60 to 75%. The dynamic slope profile follows the same patterns of change. The ratio of maximum dynamic to maximum final slope ranges from 50 to 80%. The maximum slope decreases with in- creasing rate of face advance (Peng and Geng, 1984). It must be pointed out that except for those near both sides of the profiles, each point on the displacement and slope profiles is subjected to a cycle of positive and negative displacements and slopes depending on its relative position with respect to the face.

Jan 1, 1992

By Claus Becker

The Mixshield is a tunnelling machine for water bearing soft soils. Developed on the basis of the Hydroshield, it extents the application of this machine to cohesive soils. The design of the drum-type machine allows three different applications 1. As shield with liquid supported face and hydraulical mucking 2. As Compressed-Air-Shield 3. As Earth pressure balanced shield. The Mixshield is employed on three big contracts 1. a 6.3 km ring tunnel in Hamburg, outer diameter 5.95 m, with a new developed segmented concrete lining 2. a 1.9 km pipe-jack job near Cologne, o.d. 3.6 m 3. Metro Lot 3 in Lille/France, o.d. 7.7 m, 3.2 km long with segmented concrete lining and a most sophisticated separation-plant The site experiences will be reported.

Jan 1, 1987

By Michael S. Robinson, Serge Moalli

Construction of the CSO Retention - Treatment Tunnel, Segment 1 in Dearborn, Michigan includes excavation for an overflow Structure with a minimum inside diameter of 15.24 m (finished). The excavation extends downward through overburden soil including a 15.2 m thick zone of potentially weak clay. This paper presents the subsurface data for the clay and a geotechnical analysis thereof, together with predictions of the behavior of the planned 15.54 m inside diameter open end caisson as it is sunk through this potentially weak zone. In a companion paper, the writers will compare the behavior observed with that predicted.

Jan 1, 1995

By Allyn J. Steward

The 14,350 m (47,000 ft) Mount MacDonald Tunnel is nearing completion. North America's longest railroad tunnel is being advanced from each end by two contractors. This presentation outlines techniques employed by the Manning Kumagai Joint Venture, working from the west portal. Rapid construction was achieved by simultaneous installation of cast in place arch-wall lining and drill and blast excavation. Extensive planning, judicious choice of equipment and efficient crews combined to shorten the original schedule. Manning Kumagai was also awarded the tunnel mid-section as a separate contract. This includes construction of an underground chamber and structure for a unique permanent ventilation system.

Jan 1, 1987

By Safdar A. Gill

The technique of installing small diameter caissons (drilled piers) through soft clays and water bearing ganular soil is well established for constructing building foundations. Over the past few years, the method has been utilized for constructing a large number of shafts extending into rock for the Chicago's Deep Tunnel Project. This paper will discuss design considerations for obtaining the most economic ground support system, the impact of construction procedures on the support and lateral pressures for design. Construction procedures will be described along with performance of the shafts.

Jan 1, 1981

By Donald A. Dahlstrom, Soumitro Nagpal, Timothy Oolman

Bacterial oxidation of a pyrite/ arsenopyritic gold-ore concentrate was carried out with continuous flow operation in 14 liter (1.4x10-2 m3) mechanically agitated reactors. 02 and C02 uptakes were determined at varying residence times. Bacterial concentrations were measured using a protein assay. A sharp optimum in biooxidation rates was observed with increasing steady-state residence times. Growth of the bacteria and biooxidation of the mineral were both shown to be strongly dependent on dissolved 02 levels in the liquor.

Jan 1, 1990