Search Documents

By E. Molobi

"Studs are rods threaded on both ends and are used as mechanical fasteners for two or more components. Stud finds usage in industries such as automotive, construction and aviation. The advantage of studs is that they allow for disassembly of components during maintenance. Studs are continuously subjected to both tensile and shear stresses, depending on the application, therefore they should be manufactured from suitable materials that are capable of withstanding all these external forces. Studs are sometimes manufactured from re-sulphurized steel due to its improved machinability; however, there is a certain limit on the amount of sulphur, above which failure may occur. Premature failure of studs has been a common problem, but failed studs are commonly replaced with new ones without conducting failure investigations. The present work investigates the premature failure of two re-sulphurized steel studs used on a rocker arm assembly and recommends alternative materials. The investigation was carried out by conducting visual examination, microstructural analysis, hardness measurements, chemical analysis and a detailed scanning electron microscopy (SEM) investigation on the fracture surface.IntroductionTwo rocker arm studs used on a 16-cylinder diesel locomotive engine failed prematurely after being in service for less than 5 months. The rocker arm studs had a life-cycle of 5 years. The studs were manufactured from resulphurized steel. The paper aims to establish whether re-sulphurized steel is applicable for the manufacture of studs in the automotive industry.BackgroundLocomotives are classified as either electric or fuel-powered. Diesel locomotives are an example of fuel-powered locomotives. This type of locomotive uses a diesel engine as a means for propulsion. An engine converts chemical energy into mechanical energy required for traction. In an internal combustion engine a rocker arm is an oscillating lever that conveys radial movement from the cam lobe into linear movement to open and close poppet valves of cylinders (Husain and Sheikh, 2013). The rocker arms are secured on to the cylinder head by rocker arm studs."

Jan 1, 2016

By E. L. Thyse, P. Bepswa

The Western Cape Mineral Processing Facility (WCMPF) is a collaborative educational initiative between the Department of Process Engineering at the University of Stellenbosch and the Chemical Engineering Departments at the University of Cape Town and the Cape Peninsula University of Technology. The primary objective of the WCMPF is to facilitate the education, development and graduation of suitably qualified engineering graduates and diplomats for the mining and mineral processing industries. In recent years the WCMPF has embarked on a number of initiatives aimed at improving the quality of mineral processing education which include, more importantly the introduction of novel ?end to end? or ?integrated? practicals. The practicals are developed around a specific mineral theme or route, which more than often includes the development of several new pilot plant practicals demonstrating key unit operations or processes in the selected mineral theme or route. The most recent mineral processing pilot plant practical programme is developed around the beneficiation of heavy mineral sands. The programme consist of the following developed pilotplant practicals: the online electrostatic separation of free flowing mineral sands using a Roche Mining Carrara high tension roll separator incorporating a Blue Cube Systems MQi in-line mineral quantifier; the production of titania-rich slag and pig iron from the smelting of ilmenite and anthracite in a 60 kW direct current (DC) plasma arc furnace as well as the mineralogical characterization of the feed and products; the continuous closed-circuit ball milling and screen classification of titania-rich slag. This paper illustrates the important role of a well-designed heavy mineral sands beneficiation pilot plant practical programme in facilitating the education and development of suitably qualified personnel for the mining and mineral process industries.

Jan 1, 2007

By D. Sager

Middleburg Ferrochrome (MFC), a company in Samancor Chrome, commissioned a new ferrochrome smelter in March 2009. This is a 60 MW DC-arc furnace with a DC power supply for the smelting of Transvaal chromite ore fines. With the benefit of 12 years' experience with this technology while operating a 44 MW DC-arc furnace, MFC mitigated all known challenges and considered up-scaling risk in the new plant, which had a rapid ramp-up to full power in 02 of 2009. Good operating practices, as made possible by robust equipment selection, including a thyristor rectifier set of proven technology, and operation with optimal slag chemistry, leads to a safe and effective plant operation. With the optimized furnace design and a correctly sized power conditioning system, using only standard (static) harmonic filters and a correctly sized smoothing reactor, the arc furnace is not a 'dirty load' for the utility, staying well within IEC limits for power quality. A patented arc compensation system is installed and allows for full arc position control (to compensate for magnetic field induced arc deflection) so that a symmetrical crucible is maintained, significantly benefiting refractory life. The principal benefits gained from the MFC process is the fact that ore fines are processed, without metallurgical coke, and higher chrome recoveries are achieved compared to other smelting technologies when using a DC open arc for smelting. Keywords Samancor Chrome, Middelburg Ferrochrome, ABB, smelting, DC arc furnace, arc compensation, power factor correction, anode, harmonics, thyristor, reactor, maintenance, refractory, ores, reductants.

Jan 1, 2010

By S. Budavari, F. M. C. C. Vieira

For several decades, the deep, gold-bearing reefs of the Witwatersrand basin have been mined predominantly according to layouts characterised by longwalls with strike pillars to provide regional support. During the past few years, a new generation of mining layouts has been introduced. These layouts are based on the concept of grid-type, scattered mining with dip pillars for regional support. As the extraction of the gold reefs extends to depths below 3500 m, the hazards associated with mining at these ultra-depths are expected to increase to unacceptable levels. Therefore, the question arises as to, which of the currently applied mining layouts is most acceptable for the economic and safe extraction of an ultra-deep orebody. The purpose of this paper is to describe a research investigation carried out to evaluate the degree of acceptability, from the rock engineering view point, of four currently used mining layouts for application at a depth-range of between 3500 and 5000 m. Pendant plusieurs décades, les filons d’or profonds du bassin du Witwatersrand ont été exploités d’une manière prédominante selon des dispositions caractérisées par des longues tailles avec des piliers directionnels pour donner un support local. Les dernières années ont vu la naissance d’une nouvelle génération de dispositions de mine. Ces dispositions sont basées sur le concept d’extraction type grille, éparpillée, avec des piliers au pendage pour le support local. Comme l’extraction des filons d’or va à des profondeurs en dessous de 3500m, il faut s’attendre à ce que les risques associés à l’exploitation à ces profondeurs extrêmes atteignent des niveaux inacceptables. Par conséquent, la question se pose de savoir laquelle des dispositions de mine couramment utilisées est la plus acceptable pour l’extraction rentable et sans danger d’un gisement ultra profond. Le but de l’étude présente est de décrire les recherches exécutées pour évaluer le degré d’acceptabilité, du point de vue d’ingénierie de roche, de quatre dispositions de mine couramment utilisées pour application à un rayon de profondeur entre 3500 et 5000m. Die tiefen, goldträchtigen Riffs des Witwatersrandbeckens wurden über einige Jahrzehnte hindurch vorwiegend nach jenen Layouts abgebaut, die von Langfrontstreben mit Schlagpfeilern charakterisiert waren, um regionale Unterstützung zu gewährleisten. Während der letzten Jahre wurde eine neue Generation von Grubenlayouts eingeführt. Diese Layouts basieren auf dem Konzept der Rasterfeld-Art, gestreuter Bergbau mit Neigungspfeilern für regionale Unterstützung. Es kann erwartet werden, daß auf Grund der Tatsache, daß sich die Extraktion der Goldriffs auf Tiefen unterhalb 3500 m verlagert, die Gefahren, die mit dem Bergbau an diesen Ultratiefen verbunden sind, sich auf ein nicht annehmbares Niveau erhöhen. Folglich erhebt sich die Frage, welche der gegenwärtig angewendete Abbaulayouts für die ökonomische und sichere Extraktion eines ultra-tiefen Erzkörpers am annehmbarsten ist. Zweck dieser Arbeit ist es, eine durchgeführte Untersuchung zu beschreiben, die vom Gesichtspunkt der Gesteinstechnik gesehen, vier gegenwärtig angewandte Abbaulayouts für den Einsatz in einem Tiefenbereich zwischen 3.500 und 5.000 m evaluiert.

Jan 1, 2003

By S. L. Miller

The development of a pilot gold geostatistical ore reserve system proved that geostatistical methods worked well for the routine production of annual ore reserves on gold mines of the Gold Fields of South Africa (GFSA) group, and that the techniques could also be practically implemented, understood and accepted by Survey Department personnel. Many side benefits of the pilot system became apparent, and a variety of useful management information was provided by manipulating the data values that were already captured. It was decided that it was a priority computing project to develop a standard production system (GORS) for routine use by all the GFSA gold mines. Experience with the pilot system enabled detailed functional specifications for GORS to be laid down. These, together with group computing policy determined the terms of reference and constraints for the GORS development. System design could not be finalized until new and appropriate mainframe database software and graphics workstation equipment and software had been found. With these in place the basic system was structured to take best ad- vantage of the interactive features of the workstation, the number-crunching power of the mainframe and the flexibility offered by a relational database and associated 4GL tools. Application sub-systems were developed for data capture, statistical applications, geostatistical calculations, contour plotting and graphical queries. GORS is being introduced to the mines in a phased manner with suitable documentation, training and support structures to enable it to be routinely and effectively used on a day-to-day basis by all group gold mines.

Jan 1, 1987

By D. F. Malan, J. A. L. Napier

A number of shallow coal or hard rock mines employ pillar mining systems as a strategy for roof failure control. In certain platinum mine layouts, pillars are designed to ‘crush’ in a stable manner as they become loaded in the panel back area. The correct sizing of pillars demands some knowledge of the pillar strength and the overall layout stress distribution. It is particularly important to understand the impact of the layout geometry on the effective regional ‘stiffness’ of the rock mass around each pillar. An important design strategy is to model relatively detailed layout configurations which include a precise representation of the local pillar layout geometry and to analyse multiple mining scenarios and extraction sequences to select optimal pillar sizes and barrier pillar spacing. Although computational solution techniques are now impressive in terms of run time efficiency, a major difficulty is often encountered in assigning suitable material properties to the pillars and in devising an effective material description of the layered rock strata overlying the mine excavations. This paper outlines an efficient numerical strategy that can be used to assess large-scale pillar layout performance while retaining the ability to modify individual pillar constitutive behaviour. The proposed method is applied to selected layouts to compare estimated average pillar stress values against values determined by detailed modelling and against observed behaviour.

May 3, 2023

By C. O. Aksoy, G. G. U. Aksoy, A. Fisne, I. Alagoz, E. Kaya

Coal produced in underground mines is transported to the surface by means of conveyor belts throughout long roadways. The combustion of belts puts a large number of employees at great risk. Underground collieries differ from other underground mines -due to the combustible nature of the product. The most prevalent cause of belt fires in underground coal mine is spontaneous combustion due to oxidation of the coal, which also enables the conveyor belt to burn over time. In 2014, a belt fire in an underground coal mine in Manisa-Soma, Turkey caused 301 fatalities. A study has been conducted on this accident for approximately 3 years, consisting of combustion tests in a purpose-built research gallery, comparison of the test results with mine records of the accident, and CFD modelling of the mine environment. The intensity of the fire was sufficient to redirect the air flow underground, causin large amounts of toxic gases to fill almost the entire mine in approximately 15 minutes. It is recommended that CFD analysis be used in planning emergency action strategies in underground mines.

Dec 13, 2023

By M. Timusk

"The working environment for ground support installation in mines has improved during the last 20–30 years, with more mechanized equipment for installation of ground support elements such as bolts, cable bolts, and screens. Ground support installation productivity has, however, not followed the same development curve, remaining more or less constant. In some cases, for example the mechanized installation of bolts, productivity has even dropped. One reason for this is that modern mechanized bolt rigs are complex. In this paper we evaluate manual and mechanized ground support systems, propose a way to measure the productivity of bolt rigs, and make relevant comparisons between different mines and equipment. Some productivity measures for rock reinforcement are suggested, using productivity results from eight case study mines.IntroductionTo improve safety for operators and equipment underground, ground support systems (bolts, screens, etc.) are installed in mines to stabilize the rock mass (Hoek, Kaiser, and Bawden, 1995). Important questions to ask when selecting a ground support system include where ground stability problems are located, why they have occurred, how problems should be addressed, and when and how the ground support system should be installed (Hadjigeorgiou and Potvin, 2011). The performance of bolting and screening operations in underground mines is important for both safety and productivity reasons. With greater mine depths and an increasing focus on safety, ground support has become a significant bottleneck in the production process of many mines.Many factors play a role in establishing safe and stable underground structures. Equally, there are several factors to consider in productivity, including the mining method, organization, logistics, mechanization level, and procedures. Today, most mines in Scandinavia have changed from manual to mechanized bolting, as this improves operator safety and arguably boosts net capacity. Internationally, however, manual installation of bolts remains common, with some claiming that manual installation is more productive (Bawden, 2011)."

Jan 1, 2016

By C. Bergmann, V. Ross

The concept of underground ore processing, in which valuable ore and waste are separated at a coarse particle size to improve the economics of operations and minimise the environmental impact, seems attractive from a sustainability perspective. Perceived benefits of such an operation include energy and cost savings due to a reduced hoisting load, a reduced footprint of surface operations, and using material for backfill that has not been contaminated by process chemicals. Progress in the South African mining industry in this area has however been below expectation, and opportunities for underground processing in deep, narrow reef operations were therefore explored by an Excel-based simulation with sensor-based sorting (SBS) as concentration technology. Various PGM mining scenarios incorporating factors such as the mining rate, depth of operation, and effects of dilution and particle size on the metallurgical efficiency, were compared. Whilst these initial results can be regarded as indicative only, they have shown that the economics of such an operation are driven by selective mining at significantly higher rates than achievable with conventional methods. Also, the cost of preparing, conveying and placing rock backfill will need to be lower than that of hoisting waste and depositing it on a surface dump. Another aspect to be addressed is whether ore sorting machines would be able to operate under harsh conditions underground and what provision would need to be made to ensure their efficient operation. Further investigations should focus on refining costs, incorporating environmental considerations in the modelling of economics and sustainability, and compare greenfields with brownfield scenarios. Keywords: Ore sorting, hoisting, backfill, mining rate, economics simulation

Jan 1, 2020

By G. Akdogan, S. M. Bradshaw, A. P. Van Wyk, T. Punt

Recycling has become an important part of the lithium-ion battery (LIB) life cycle due to the growing demand for energy storage in applications like electric vehicles and renewable energy. Recycling spent LIBs provides a secondary source for strategically scarce metals, like lithium and cobalt, helping to reduce the environmental impact of LIBs. Organic acids have been proven to be effective lixiviants with the benefit of reduced environmental impacts, amongst which citric acid has shown to exhibit similar extraction performance when compared to mineral acids. Leaching LCO and NMC batteries with 1.5M citric acid and 2 vol.% H2O2 at 95°C, 20 g/L for 20 minutes achieved 93% Al, 90% Co, 96% Li, 94% Mn and 94% Ni dissolution. The strong chelating property of citric acid affects the separation of the metals, providing unique extraction opportunities. The first extraction uses 12 vol.% D2EHPA at a pH of 2.5 and O/A ratio of 2 to separate 96.4% Mn and 100% Al from the PLS in two counter-current stages. Stripping the loaded organic with 1.25M citric acid at an A/O ratio of 3 allows for up to 91% stripping of the manganese in a single stage. The second extraction then separates 96.5% Li from the PLS in three counter-current stages using 20 vol.% D2EHPA at a pH 5.5 and O/A ratio of 5. The raffinate remaining after the second separation contains 48.4 wt.% Co and 50.3 wt.% Ni. Keywords: Hydrometallurgy, lithium-ion batteries, metal recycling, citric acid, solvent extraction

Jan 1, 2020

By M. L. Mahlatji

Mechanical alloying of an equiatomic mixture of crystalline Ti and Pt elemental powders in a high-energy ball mill formed an amorphous alloy by solid-state reactions. Mechanical alloying was carried out in an argon atmosphere at a rotation speed of 1200 r/min and a 20:1 ball-to-powder weight ratio, for time intervals of 4 to 40 hours. At an intermediate stage of mechanical alloying, scanning electron microscopy showed the formation of characteristic layered structures of inhomogeneous composition within the powder particles. X-ray diffraction analysis showed the gradual disappearance of crystalline Bragg peaks and the emergence of broad amorphous maxima as milling progressed. The amorphization process was completed after 8?12 hours. The amorphous state of the product indicated that temperatures during processing did not exceed the crystallization temperature of the alloy.

Jan 1, 2014

By R. Ajalloian, L. Karimzadeh

This paper describes the engineering properties of Givi dam foundation. Givi dam will be built across the Givi River on the andesitic rocks (Karaj formation) in Ardabil province (northeast of Iran). Geotechnical investigations including drilling, pumping tests, sampling for laboratory testing and discontinuity survey. Physical and mechanical properties of andesitic rocks such as density, water absorption, porosity, uniaxial compressive strength, triaxial compressive strength, durability and direct shear tests are evaluated in this paper. Discontinuity data are process for the determination of dominant sets and for the rock mass characterization in terms of classification systems ( RMR, Q and RSR ). Correlations between these three classifications are discussed. Le barrage doit être construit sur la rivi_re givi qui cou_e sur les andesites (formation de Karaj)dans la province d_ Ardebile situee_ a Nord- Ouest de l_ _Iran. Les études géophsique commesondage, Pompage. Et échantillonnage afin de verifier les discontinutés out éte_ effectuées. Lesproprietés physique et méchanique des roches andesifique ont éte_ verifieés. Les informations concernaüt aux discontinuitiés afin de montrer leur principale direction ont éte_ verifieés, les proprietés des roches dans leurs ensemble ont éte_ etudieés. Les divers classifications(RMR,Q,RSR ) ont éte_ comparés et analyseés. Dieses Schreiben ist zur Erklaerung der Ingenieureigenschaften ueber Baugrund des Givi Deiches.Dieser Deich soll im Givi fluss auf Andesitgesteine (Karaj formation) gebaut werden. Der platzdes Deiches legit im Ardebil Provinz nordwestlich von Iran. Geotechnische Untersuchungen Sind:Bohrungen, pumpen Versuche, Probenentnahme fuer Laborversuche, BrechbarkeitBestimmungen, physikalische und mechanische Eigenschaften der Andesitgesteine wurde hierausgewertet, wie Z.B.: Wasserleitfahigkeit, Porositaet, Scherfestigketswiderstand, Informationenueber Brechbarkeiten der Gesteine wurde gesamelt, und die meisten Brechbarkeiten bestimdamitman die Gesteine besser klassifizieren kann. In Endefekt wrid die Resultate verschiedeneKlassifizierung wie RMR, Q, und RSR besser geachtet und zusammen vergliechen.

Jan 1, 2003

With the advent of the First World Conference on Sampling and Blending (WCSB1) in Denmark in 2003 and the subsequent biannual meetings, together with other sampling conferences held on a regular basis, the central tenets of sound sampling practice and theory are spreading throughout the minerals industry. End-users and project houses, or groups who execute the projects, are all now better-informed about the principles of ?correct? sampling and preparation. To support this, many large mining companies now have their own in-house champion who will advise and ensure that the supply of sampling equipment is correct in terms of design and application, which further contributes to improved metallurgical accounting. The presence of a sampling champion also ensures that consistent and acceptable standards in regard to sampling practice are maintained throughout the group. This has, in turn, placed a greater degree of responsibility on the shoulders of sampling equipment suppliers, in terms of their equipment designs and product offerings, as well as applications knowledge for effective installation of equipment on client plants. This paper attempts to highlight the significant challenges that sampling equipment manufacturers often face with regard to complying with the newly understood requirements of best practice and sampling equipment design. Manufacturers invariably face issues with end-users or project houses, including project cost control, restricted headroom for samplers in plant layouts, and a lack of knowledge in certain quarters. These all have a potentially negative effect on the final outcome of a proposed sampling solution or implemented project. In reality, what is intended by all parties and what is ultimately installed are at times very different, with undesirable consequences for all concerned. Against this challenging background, there are, however, a number of instances where intent and implementation are complementary, with very satisfactory results. Keywords sampling, mechanical samplers, design, installation, sampling theory.

Jan 1, 2014

By D. Farrow

Future development of kimberlite mines is now focused on mining at deeper levels. The consequences are increased difficulty and costs of the mining operations. The decisions on investments require accurate resource evaluation and quantification of the risk. In the decision process the first step consists in choosing the number of boreholes sampling the pipe relative to the level of uncertainty that can be accepted. The uncertainty in the volumes of rocks of different types can be assessed as soon as we can estimate these volumes from a given borehole layout and calculate the error by means of its variance for instance. In theory this can be achieved by using geostatistical techniques (‘transitive theory’), but in practice the calculation of the error on volumes can be achieved in very particular cases, assuming some regular sampling patterns. A different approach has been chosen based on simulations, giving maximum flexibility to reproduce the reality of the sampling procedure. The idea is to simulate the geometry of several ‘possible’ pipes with their internal geology and estimate them by kriging. Several experimental errors are obtained on which risk analysis can be performed. The aim is to find a feasible method to perform the simulations with reasonable chance to correctly represent the reality, without data on the pipe extension. The methodology applied is based on some hypotheses that can be assessed by the geologist as well as by the geostatistician. The procedure assumes a geological model based on current knowledge including appropriate geostatistical variation. What make these simulations specific and powerful in this case comes from the fact that the boundaries between the different rock-types can be simulated using a transformation of the real 3D space into a 2D space defined by means of polar coordinates. Ultimate transformations to account for smoother variations with morphological transformations allow the generation of realistic pipe geometries on which sampling pattern can be used to evaluate the estimation errors. By estimating the simulated pipe geometries with different boreholes layouts a risk curve expressing the uncertainty in the volumes of the different rock-types versus the number of holes can be developed.

Jan 1, 2003

By L. Lorig

"Two types of extreme event, earthquakes and rainfall, potentially affect open pit slope stability. In the case of earthquakes, there are rather well-developed analysis procedures and acceptability criteria. The analysis procedures relate mainly to selection of the dynamic loading either through design earthquakes and/or pseudo-static seismic coefficients. The acceptance criteria are typically expressed in terms of a minimum safety factor in pseudo-static analyses. The acceptance criteria are often promulgated by governments despite the fact that no open pit slope has ever been adversely affected by an earthquake. This paper explains why open pit slopes are seemingly more resistant to dynamic loads than natural landforms, which can experience catastrophic landslides.Extreme rainfall events are much more likely to cause open pit slope problems than earthquakes. Two types of problem are common – slope erosion and slope instability. Slope erosion is often mitigated by appropriate surface water controls. Slope instability due to elevated transient water pressures is more difficult to mitigate. Analysis procedures and acceptability criteria are rare. This paper will discuss the mechanisms for rainfall-induced slope instability, as well as analysis methods. Examples will be discussed and analysis methods are proposed. IntroductionTwo types of extreme event, earthquakes and rainfall, potentially affect open pit slope stability. In the case of earthquakes, there are rather well-developed analysis procedures and acceptability criteria. The analysis procedures relate mainly to selection of the dynamic loading either through design earthquakes and/or pseudo-static seismic coefficients. The acceptance criteria are typically expressed in terms of a minimum safety factor in pseudostatic analyses. The acceptance criteria are often promulgated by governments (e.g., Peru, Chile) despite the fact that no open pit slope has ever been adversely affected by an earthquake. This paper explains why open pit slopes are seemingly more resistant to dynamic loads than natural landforms, which can experience catastrophic landslides.Extreme rainfall events are much more likely to cause open pit slope problems when compared to earthquakes. Two types of problems are common – slope erosion and slope instability. Slope erosion is often mitigated by appropriate surface water controls. Slope instability due to elevated transient water pressures is more difficult to mitigate. Analysis procedures and acceptability criteria are rare, but do exist. In Peru, for example, slopes are required by law to be designed for a 100-year storm."

Jan 1, 2016

By J. H. Zietsman, W. J. Leipoldt

"To be able to responsibly develop a multiphysics model of the steel belt sintering (SBS) process used to sinter chromite fines, it is important to have a comprehensive understanding of the process. This understanding was gained through a site visit, observation of the process in operation, and interaction with the operators. Material characterization will also reveal much about the process that is not yet fully understood. A well-defined and representative mass and energy balance will also give valuable insight into the process. The plan for the multiphysics model aims to combine a computational fluid dynamics (CFD) model with a discrete element method (DEM) model.To obtain a more accurate mass and energy balance representation of the SBS process, it was decided to develop a dynamic distributed parameter model of the mass and energy balance. This model will be used to gain better understanding of the SBS process so that a more complicated multiphysics model can be developed later. The reason for this is because the SBS process is very dynamic, with a large temperature distribution throughout the length of the process. In its current state, the mass and energy balance model is capable of handling solid and gas material packages and exchanging heat between these packages where they are mixed, and is able to model the heating of the gas by burning CO gas. The next step in the development of the model will involve enabling it to handle evaporatoin of liquid water, burning of solid carbon in the pellets, reduction of iron oxide in the pellets with the CO gas formed from carbon combustion, and then oxidation of the reduced iron in the oxygen-rich cooling zones."

Jan 1, 2014

By C. A. Garzonio, A. M. G. Affuso

The paper describes the analyses and the tests carried out on representative slabs of white Carrara marble which have highlighted the correlation between the micro fabrics and physical and mechanical parameters. The aim is to determine the conditions which indicate the triggering and evolution of the deformation phenomena. La note écrit l’analyse et les epreuves effectuée sur un echantillon représentatif de nombreuses dalles en marbrede Carrara. Les études montrent la correlation entre la minéralogie et les paramètres physiques et mecaniques. Le but est déterminer les conditions qui indiquent l’amorçage et l’evolutions des phénomènes de déformation. Diese Arbeit gibt eine Beschreibung der experimentalen Untersuchungen und der Analysen über die Marmorplatten von Carrara. Daraus resultiert, dass die Charakterisierung der Mineralogie und die Porosität der Gesteinsmaterialien die physikalische mechanische Degradation beurteilen und die Krümmungen bestimmen.

Jan 1, 2003

By P. N. Erasmus

This paper considers the fundamental concepts of support design for underground openings in highly stressed ground. It concludes that the conventional deformed reinforcing bar, woven mesh and cable lacing support methods that have been widely used in deep gold mines are quite in appropriate for the support of highly stressed tunnels. The following is suggested as the criterion for adequate dynamic support under rockburst conditions: the energy absorbed by a support unit (yielding through some acceptable limited displacement) should exceed the kinetic energy generated by the mass of rock that is intended to be retained by that unit. Duraset in conjunction with SRK Consulting has developed a yieldable steel tendon called the Durabar®. It is unique in the sense that it cleverly utilizes the property of the ductility of ordinary low-carbon steel from which it is made to accommodate the excessive displacement it is subjected to in the case of rockbursts or swelling ground.

Jan 1, 2009

By A. J. Rogers

The KX36 kimberlite was discovered using a high-resolution gradient aeromagnetic survey, with follow-up detailed ground geophysics and deflation soil sampling used to assess and prioritize the geophysical anomalies identified from the initial aeromagnetic survey. Prospect drilling intersected kimberlite in the first hole drilled on the KX36 anomaly. Preliminary evaluation has shown that KX36 is diamondiferous, and a more detailed evaluation and sampling programme is currently underway. The area around KX36 has been prospected by numerous companies over the last few decades, with sporadic kimberlite indicator mineral (KIM) recoveries in regional deflation sampling indicating the possible presence of kimberlites, but without sufficient resolution to ?home in? on specific targets. Previous (lower resolution) aeromagnetic surveys and soil sampling campaigns also did not define anomalies with sufficient detail to guide prospect drilling effectively. The discovery of KX36 highlights the prospectivity of areas of Botswana under deep Kalahari cover that have been explored previously. Keywords kimberlite exploration, central Kalahari, overburden, high resolution aeromagnetics, deflation sampling, KIM.

Jul 1, 2013

By I. M. Morsi

The present study investigates the feasibility of using some materials as start-up slags for the extraction of magnesium metal from Egyptian dolomite ores by the Magnethermic technique. The reduction of roasted dolomite (dolime) takes place in a closed evacuated electric arc furnace (small Magnetherm reactor) using ferrosilicon as a reducing agent and liquid start-up slag as a reduction bath under an inert atmosphere. The operational parameters affecting the stabilization of the start-up slag composition and the extraction of magnesium such as reducing agent stoichiometry, reduction temperature, and time were investigated. The dolomitic charge was in the form of sintered briquettes. The charge was reduced under an argon atmosphere in the Magnetherm reactor for constant period and constant temperature. The results showed that the clinker can be used as a start-up slag for the magnethermic process. Also, the optimum conditions for the extraction process were found at 2XSi stoichiometry to give maximum reduction of 80% after 15 minutes reduction time at a temperature of 1550°C. XRD and XRF measurements were used to determine the phases present and the extent of reduction of magnesium, respectively. Keywords magnesium, dolomite ore, magnetherm, magnetherm reactor, silicothermic reduction.

Jun 1, 2013