Search Documents

By M. -H. Fillion

"Geotechnical stability analysis and design in open pit mines requires access to representative geological, structural, hydrogeological, and rock mass models. The quality and quantity of collected geomechanical data used to build such models can have significant implications in the design of safe and economically viable slopes. Data collection is a continuous process throughout the life of a mine. The process starts from exploration to conceptual/preliminary feasibility, feasibility, design and construction, operations (early production/late production), and mine closure.As geomechanical data is often limited at an early stage of a project, the estimated variability of the geotechnical factors may be larger than the actual data variability. This can potentially result in a conservative selection of the pit slope angle. Collecting additional geomechanical data at later stages of the mine development may contribute to reducing the uncertainty associated with the geotechnical properties and a steeper slope angle may be used for the design. This can result in significant economic benefits.This paper investigates the impact of access to new data over time, following a series of geomechanical data collection campaigns, on design decisions. This is illustrated by comparing the resulting slope design, at three stages of the mine project, at a South African open pit mine. To demonstrate this, a series of slope stability analyses were performed using limit equilibrium tools. For each project stage, the slope angle design was modified until a similar probability of failure of 5% or less was obtained. The corresponding factor of safety distributions for each project stage were then compared to evaluate the impact of collecting additional data on the resulting slope design.The results showed that data variability can differ significantly from one project stage to another. Data variability may be greater at more advanced project stages (i.e. a wider distribution of the factor of safety). Furthermore, the results showed that, even for the cases with greater variability, steeper slope angles were possible at more advanced stages for the proposed design requirement (probability of failure < 5%). In this investigation, as more data became available, the uncertainty associated with data variability could be sufficiently reduced to allow the selection of less conservative slope angles. This can be used as a managerial tool in developing data collection strategies and allocating the necessary funds, and can lead to important economic benefits to the mining operation."

Jan 1, 2016

By F. Yang, T. Pan, T. Zhao, Z. Shao, D. Zuo

In this paper, the development and applications of robot technique is summarized, and the status and developing direction of China coal mine robotics. A description of the research meaning, frame and key technology of underground salvage robot is given. Keywords: coal mine, robot, special robot, salvage robot.

Jan 1, 2003

By P. Fu, Y. Ma

Residual collectors and their byproducts (e.g., CS2) in flotation effluents can cause water contamination and even result in serious health hazards to humans and animals, Therefore, residual flotation reagents should be removed properly before discharge or recirculation into flotation circuits. In this work, four thiol collectors (potassium ethyl xanthate (EX), sodium diethyl dithiocarbamate (SN- 9), O-isopropyl-N-ethyl thionocarbamate (Z-200), dianilino dithiophoshoric acid (DDA)) were chosen as model pollutants. The collector removal, mineralisation and byproduct formation were compared by sole O3 and O3/UV185+254nm. The degradation rate constants of thiol collectors by O3/UV185+254nm were 2~6 times higher than those by sole O3. The mineralisation of collectors was also remarkably enhanced by O3/UV185+254nm. The degradation efficiency by O3/UV185+254nm had the order: EX>SN-9>>Z- 200>DDA. The Z-200 and DDA were refractory flotation reagents. The degradation of thiol collectors caused the reduction of solution pH and the increase of ORP and conductivity. However, the O3/UV185+254nm achieved more evident changes of these parameters than sole O3. During the degradation of thiol collectors, less than 4% of total sulfur in collectors was emitted into air as CS2 and H2S. Compared to sole O3, the O3/UV185+254nm had additionally included UV185+254nm photolysis and O3/UV254nm, resulting in higher efficiency in removing collectors. The O3/UV185+254nm was an effective process in treating mineral flotation wastewaters containing organic reagents. Keywords: Thiol collectors; flotation effluents; ozone; vacuum-UV; degradation, mineralisation

Jan 1, 2020

The Steering Committee for Minerals and Mining Policy convened two workshops during March 1996 to address the following topics: Business Environment- National and Provincial Powers, Administration and Regulation, Mineral Marketing, Beneficiation, Research and Development, Environmental Issues, Mining Impact on Surface Usage, Southern Africa Regional Issues. Human Resources: Elementary Residual Racism, Housing, Downscaling, Migrant Labour and Human Resource Development. Mineral Tenure: Mineral Rights, System of Access to Mineral Rights, Access to Exploration information, optimal Exploration, Trust Lands. Small-scale Mining. Development of Small-scale Mining, Artisanal Mining.

Jan 1, 1996

By A. T. van Zyl, M. Mthenjane, M. J. Cole

Growing global concern over the impacts of climate change, attributable largely to fossil fuel energy sources, has led to the widely shared goal for a ‘just transition’ to cleaner energy and reduced dependence on carbon-based fuels. As the world’s 14th biggest CO2 emitter and being particularly vulnerable to the impacts of climate change, South Africa must embark on a just transition pathway. This paper reviews expected coal mine closures and associated community vulnerabilities and local governance challenges in South Africa. Decommissioning schedules for all coal-fired power stations and operating coal mines are plotted, and 69 mining host communities and 21 municipalities are mapped, classified, and described. Community socio-economic profiles are measured using a set of SDG indicators and census data and municipalities assessed through financial audits. Our research shows that five coal-fired power plants (8.9 GW) and 15 coal mines (29.5 Mt/a) will probably close by 2030, and a further four plants (14 GW) and 23 mines (106 Mt/a) by 2040. Thus, the shift to cleaner energy will likely occur without the premature closures implied by the just transition. The impact of mine closure on the 2.5 million residents of host communities will be significant, particularly as levels of income, employment, and education are already very low and many municipalities are in financial distress. The South African approach to the just transition needs to take local realities into account and the narrative must support an effective transition that does not undermine energy security and economic growth.

Jun 5, 2023

By M. Grave

Rock Engineers are required to design safe cost effective support systems and stoping layouts for their respective mines. As each stope has its own unique environment, continual re evaluation is required in all stopes to maximize extraction and achieve value from the support standard. This paper presents numerical modelling used to plan early mining within the shaft pillar and a reevaluation of an existing stope support standard.

Jan 1, 2009

By PC Pistorius, DR Groot

The South African base metals industry has been one mainly focused on the production of metals or metal compounds from primary ores. This is true for metals such as titanium, vanadium, chrome, manganese, cobalt, nickel, copper, zinc and aluminium. The steel making industry has traditionally used a substantial portion of scrap steel, and could thus be considered to be somewhat of an exception. Secondary sources have played much less of a role, possibly due to at least some of the following factors. Scrap material is often of unknown composition, and thus it requires additional chemical analysis, and possibly special treatment. Tonnages are relatively small, and the incorporation of secondary materials is possibly seen to carry undue risk and inadequate benefit. South African consumers are still not very conservation and recycling conscious, which limits the amount of scrap made available. This attitude might also be expected to influence decision makers in these industries. Finally, pressure from environmentally motivated activists locally has not been unduly large. This landscape has been changing, and is continuing to do so. Various municipal authorities such as those of Pretoria, Johannesburg and Cape Town are reporting increasingly limited landspace for waste (Bondolfi, 2007). There are increasing concerns regarding the leaching of hazardous metals such as chromium, mercury and cadmium from landfill waste, especially electronic and electric wastes ? the so-called eWastes. In more developed countries such as the United States of America and Western Europe the problem of eWaste has grown to the extent where legislation has been enacted, such as the Waste Electrical and Electronic Equipment (WEEE) legislation of the EU (European Union Directive 2002/96/EC). The 19th and 20th centuries have seen major technological advances. Relevant to this paper is the availability of centrally generated electrical power, telecommunication, entertainment through recorded and transmitted music and images, the growth and pervasive influence of electronics, and the handling of digital data by computers and microprocessors. These developments have placed ever increasing demands on resources for the manufacture of electrical and electronic equipment, as well as on the generation of electrical power. Most of the resources required are non-renewable: copper, steel, aluminium and other metals, various thermoplastic polymers such as PVC (polyvinyl chloride), polyethylene and ABS ( acrylonitrile-butadiene-styrene), thermosetting polymers such as epoxies, elastomers such as butyl rubber, glasses and ceramics, and composites such as fibre reinforced plastic (fibreglass). The conservation of non-renewable resources inevitably includes recycling. To a certain extent, recycling of materials locally is well established. Thus glass, paper, used oil, car batteries, ferrous scrap such as beverage cans and non-ferrous scrap such as

Jan 1, 2007

By Z. Xingrong, L. Jiongtian, Z. Yangge, C. Yijun, L. Liang, H. Yangjia, H. Long

In this present research, a polymer poly (acrylamide-allyl thiourea) (PAM-ATU) with an average molecular weight 1.66 × 104 g/mol was used as a depressant in the flotation separation of molybdenite from chalcopyrite and galena. The micro-flotation experimental results showed that PAM-ATU exhibited a strong influence on the flotation performances of chalcopyrite and galena, but had little effect on that of molybdenite within a pH range of 9.0~11.0 at a dosage of lower than 6.0 mg/L. The flotation results of bulk flotation tests illustrated that PAM-ATU showed a stronger depression power than sodium thioglycollate (TGA) and sodium sulfide. The comparison results demonstrated that PAM-ATU and TGA had an advantage in reducing galena and chalcopyrite impurities in the molybdenum concentrate, respectively. With the combination of PAM-ATU and TGA, a good flotation separation result was achieved through one roughing operation where the recovery of molybdenum in the froth product was over 75.0%, while the recovery of copper and lead were less than 22.0% and 15.0%, individually. It was also found that a molybdenum concentrate with Mo grade of 46.32%, Cu grade of 0.16%, Pb grade of 0.06%, was obtained by a closed circuit flotation flowsheet of one roughing-three scavenging-five cleaning with a Mo recovery of 77.67%. Keywords: PAM-ATU, molybdenite, depressant, chalcopyrite, galena

Jan 1, 2020

By V. Velicka, J. Ptacek, R. Snuparek, P. Konecny, G. Takla

Coal mining in Ostrava-Karvina coalfield is being accompanied by rockbursts. 82 rockbursts occurred within the period between 1990 and 2002. Natural and technological factors from these rockbursts were collected and analysed. They confirmed that rockbursts are complex geomechanical events and that the relations between co-acting technological and natural factors are very complicated. Der Abbau in dem Ostrava-Karvina Steinkohlenrevier wurde von Anfang an durch Gebirgsschläge begleitet. 82 Gebirgsschläge in dem Zeitabshnitt von 1990 bis 2002 erfolgten. Die Angaben über natürliche und technische Faktoren der Gebirgsschläge wurden gesammelt und analysiert. Es wurde bestätigt, dass die Gebirgsschläge komplexe geomechanische Phänomene sind und dass die Beziehungen zwischen den zusammenwirkenden Faktoren sehr kompliziert sind. L´abattage d´houille dans le Bassin houiller d´Ostrava-Karvina est accompagnée par les coups de terrains. 82 coups de terrains s´étaient produit dans la période entre 1990-2002. Les données sur les facteurs naturels et techniques ont été ramassées et analysées. Les résultats ont corroboré que les coups de terrains sont des phénomènes géoméchaniques complexes. Les relations entre les facteurs techniques et naturels coopérants sont très compliqués.

Jan 1, 2003

By I. Cameron, S. Ramjee, A. M. Garbers-Craig

The cause of reduced workability and increased ageing of a blast furnace taphole clay was examined. The investigated taphole clay contained 60 mass% alumina, with phenol-formaldehyde resole resin and liquid pitch serving as the binder system. The workability and Marshall extrusion pressure of the as-manufactured clay samples were evaluated to assess the extent of ageing of the clay. The wettability of all the raw materials was investigated to confirm compatibility between the dry raw materials and both the resin and liquid pitch, while the dry raw materials were analysed using XRF, XRD, and SEM-EDS. The characterisation of the resin and liquid pitch, as well as an analysis of their interaction, was performed using viscosity measurements, Fouriertransform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), and differential scanning calorimetry (DSC). The analyses confirmed a chemical interaction between the resole resin and liquid pitch, where the chemical structure of the resole resin changed when mixed with pitch, preventing the typical curing behaviour of the resin. Upon ageing of the resin-pitch mixtures, the resin underwent premature cross-linking, causing the curing process to initiate at lower temperatures, i.e., earlier onset of curing. This premature cross-linking was likely due to secondary amines present in the liquid pitch, which acted as a catalyst for the curing process of the resin. This reduction in curing temperature after ageing was confirmed by an increase in binder viscosity, which was identified as the primary cause of reduced workability, accelerated ageing, and increased Marshall extrusion pressure of the taphole clay.

Jul 23, 2025

The annual General Meeting of the Branch was held in the St. Helena Club on Wednesday, 4th August, 1971 at 8.00 p.m. Mr N. A. Honnet (Immediate Past Chairman) was in the chair. There were also present Mr V. C. Robinson, President of the South African Institute of Mining and Metallurgy. Nine Fellows: Messrs J. R. F. Handley, C. J. Isaac, J. Lorenzon, J. M. Meyer, C. Mostert, D. A. Smith, S. L. S. Swart, I Thomas and R. G. Williams. Five members: Messrs R. Campbell, A. H. Edwards, K. Pearce, G. P. Rundle and R. B. Sutherland. Five graduates: Messrs J. E. Andrews, E. J. Shillaber, M. H. Smith, T. R. Stromsoe and D. J. van Niekerk. Two associates: Messrs A. Paschalides and D. S. Robinson. Eight visitors. Total present: Thirty-one. MINUTES OF THE PREVIOUS GENERAL MEETING As the minutes of the General Meeting held on the 16th June, 1971, had not been published in the Journal, the Chairman moved that the adoption and discussion thereof be deferred to the next General Meeting. This motion was adopted unanimously. The minutes of the General Meeting held on the 10th February, 1971, were taken as read. The adoption, which was proposed by Mr D. A. Smith and seconded by Mr J. M. Meyer, was carried unanimously. At Mr Honnet&apos;s request, Mr V. C. Robinson took the chair during the presentation of the Chairman&apos;s Annual Report. CHAIRMAN&apos;S ANNUAL REPORT 1970/71 1970/71 Committee-Office Bearers: Chairman - J. N. Saunders Vice Chairman - G. Y. Nisbet Immediate Past Chairman- N. A. Honnet. Due to the sudden retirement of Mr J. N. Saunders, the committee, at a meeting on the 3rd February, 1971 elected Mr G. Y. Nisbet as Chairman with Mr J. M. Meyer as Vice Chairman. After the transfer of Mr Nisbet to C.D.M., the committee, as a meeting on the 12th May, 1971, decided that Mr Meyer hold the Chair in an acting capacity for the remainder of the year. Committee members: Messrs C. J. Isaac, J. G. Kirchener, L. O. W. Leimer, R. S. Pearson, I. G. Thomas and A. von Holdt. Transfers of several office bearers and committee members resulted in Messrs J. M. Meyer, D. N. Smith and G. C. J. Young being co-opted onto the committee.

By B. F. Giyani, A. Salama

Tanzania is a country with a variety of mineral deposits, including metallic minerals, gemstones, mineral fuels, industrial minerals, and critical minerals. This study provides an overview of mining legal framework, mineral occurrence and production, challenges in the mining sector, and government initiatives. The aim is to demonstrate the development of the mining sector in Tanzania and explore the potential for further mining investment in the country. The mineral production data showed generally increasing trends over the years, for example, gold production increased from 42 tonnes in 2018/2019 to around 50 tonnes in 2023/2024. Despite the growth, the mining sector encounters several challenges, including a lack of detailed geological information on mineral deposits, inadequate infrastructures in some remote mining sites, the existence of informal artisanal miners, and mineral smuggling. The Tanzanian government has introduced several initiatives to address these challenges, including carrying out the highresolution airborne geophysical survey to increase geological information in some areas, the formalisation of artisanal and small-scale mining, establishing mineral markets to combat mineral smuggling, and encouraging mineral value addition within the country.

Oct 24, 2025

By Didier Kasongo NYEMBWE

The paper circumscribes the base metal casting industry in Southern Africa. It essentially consists in the founding of copper and zinc alloys. The challenge related to the scarcity and the unaffordable quality patterns and dies faced by the industry is discussed. New manufacturing technologies for foundry tooling called Rapid Prototyping that can possibly be used to alleviate the above mentioned challenge are then presented and their benefits assessed.

Jan 1, 2007

Mineral sand beneficiation plants comprise a complex combination of electrostatic, magnetic and gravity based separation techniques. These are combined and replicated in ways that provide the most efficient and cost effective separation of the valuable components. On line instrumentation has been developed at the JKMRC (eg. conductor/non-conductor(CNC) ) to measure the properties of the dry plant process streams. This paper provides results from the recent development of a novel low cost mass flow meter and discusses their combined use with the CNC instrumentation for the control of dry separation circuits.

Jan 1, 2003

By B. Genc, P. Malepfane

This study proposes a new approach to reduce the environmental impact during surface mining by improving environmental factors through the incorporation of carbon footprint into strategic mine planning. Two key variables were analysed by contrasting and comparing the baseline and optimised models generated. These variables include net present value, which helps determine the financial feasibility of the mining models and their carbon emissions. The variables were analysed by using linear regression, Spearman’s correlation, a P-value hypothesis, and an exponential decay test. Results show that at Mine A the projected net present value was 62% higher than when running a baseline model. Furthermore, the net present value from the baseline model portrayed a high rate of decay at 0.667 versus 0.118 from the optimised model. This indicates the baseline model’s sensitivity to long-term project timelines and fluctuating markets. The optimised method presents an opportunity to manage emissions during the high operational costs phases. It is represented by a 31% improvement in carbon emissions during the periods of high operational costs, whilst maintaining a positive net present value when compared with the baseline model. It was shown that the optimised model presents a better chance of achieving financial feasibility and balancing environmental impact, thereby ensuring that Mine A can align with the environmental aspect of economic, social, and governance principles through lowering the carbon footprint resulting from its hauling operations.

Jan 30, 2026

By S. T. Johansen, B. T. Løvfall, T. Rodriguez Duran

In this paper we develop a physics-based model for lining erosion in steel ladles. The model predicts the temperature evolution in the liquid slag, steel, refractory bricks, and outer steel shell of the ladle. The flow of slag and steel is due to forced convection induced by inert gas injection, vacuum treatment (extreme bubble expansion), natural convection, and waves caused by the gas stirring. The lining erosion takes place by dissolution of refractory elements into the steel or slag. The mass and heat transfer coefficients inside the ladle during gas stirring are modelled based on wall functions which take the distribution of wall shear velocities as a critical input. The wall shear velocities are obtained from computational fluid dynamics (CFD) simulations for a sample of scenarios, spanning out the operational space, and a model is developed using curve fitting. The model is capable of reproducing both thermal and erosion evolution well. Deviations between model predictions and industrial data are discussed. The model is fast and has been tested successfully in a ‘semi-online’ application. The model source code is available to the public at [https://github.com/SINTEF/refractorywear].

Apr 16, 2024

By M. Handley

The Witwatersrand Basin contains by far the most gold ever found, and has hosted mining from its discovery in 1886 to the present. For many years, South Africa was the world’s largest producerof gold, nearly all of which came from the Witwatersrand. Since 2000, South Africa has fallen back several positions because of declining gold output. There are many complex and varied reasons for this; however, declining gold resources in the Witwatersrand Basin are not one of them. As far as the author knows, there are no qualified estimates in the literature of gold remaining in the Witwatersrand Basin. This paper collects mining data from several sources and then, using elementary gold accounting and error analysis, attempts to estimate the amount of gold remaining in the Witwatersrand Basin. It includes gold underground in existing and defunct mines, in evaluated ore resources, and dumps. Compiled data from 1887 to 2019 shows that 50 200 t of gold were produced by Witwatersrand mines, while it is estimated that a further 48 100 t remainunderground, both within and outside of mine leases, a further 1 600 t on the surface in tailings,and an unknown amount in rock dumps. Nearly all of this gold will remain inaccessible with current mining methods, and major technical developments in mining will be necessary before any of the gold can be categorized as a code-compliant resource or reserve. To win this prize, the mining industry will have to rethink its approach to mining, both in old mining leases and in the unexploited ground. It will also have to find effective means of preventing gold theft and informal mining, which are on the rise.

Apr 5, 2023

By M. A. Mahboob, T. Celik, B. Genc

Mineral Resources estimation plays a crucial role in the profitability of the future of mining operations. The conventional geostatistical methods used for grade estimation require expertise, understanding and knowledge of the spatial statistics, resource modelling, geology, mining engineering as well as clean validated data to build accurate block models. However, the geostatistical models are sensitive to changes in data and would have to be rebuilt on newly acquired data with different characteristics, which has proved to be a time-consuming process. Machine learning methods have in recent years been proposed as an alternative to the geostatistical methods to alleviate the problems these might suffer from in Mineral Resource estimation. In this paper, a systematic literature review of machine learning methods used in Mineral Resource estimation is presented. This has been conducted on such studies published during the period 1990 to 2019. The types, performances, and capabilities, of several machine learning methods have been evaluated and compared against each other, and against the conventional geostatistical methods. The results, based on 31 research studies, show that the machine learningbased methods have outperformed the conventional grade estimation modelling methods. The review also shows there is active research on applying machine learning to grade estimation from exploration through to exploitation. Further improvements can be expected if advanced machine learning techniques are to be used.

Nov 30, 2022

By P. Schutte

It is evident from most admired companies, globally, that they drive key priorities such as teamwork, customer focus, fair treatment of employees, initiative and innovation into their organisations. It is clearly proofed in all the research that the role of the human factor, and therefore human behaviour, is pivotal to companies striving to accomplish goals such as competitiveness, customer delight, high quality, growing productivity as well as a safety-committed work force. The challenge of leadership is to change the worker’s poor perception of safety to an excited, empowered, valued employee who is continuously committed to the achievement of high levels of health, safety and conformance – the challenge therefore is to transform from within. Any work force needs a set of behavioural rules which work for it – including safety rules and critical safety behaviours, which are accepted through involvement leadership, encouragement and support.

Jan 1, 2003

By K. Gharibi, A. Dehghani, S. Farrokhpay, M. Aghajanloo, M. Ostadrahimi

The effect of flotation operational parameters on froth stability and froth recovery was studied. Froth stability was measured using a special column. To determine the froth recovery, the froth height change model and froth height exponential model were used. It was found that since the interactions between the pulp and froth zones affect the time of froth formation, the exponential model is more suitable than the froth height change method for determining the froth recovery. The results showed that superficial air velocity and collector dosage have, respectively, the highest and lowest effect on the froth recovery, while froth recovery decreases sharply with increasing froth height.

Jan 1, 2021