Search Documents

By H. William Zeller, T. E. Westpha1

The U.S. Bureau of Mimes evaluated the effects of two iron-based fuel additives on diesel particulate matter (DPM) emissions. The 5.6-L, six-cylinder test engine is typical of engines used in underground mines. One additive, ferrous picrate, did not measurably affect exhaust emissions. This report is mainly about a ferrocene-based additive that reduced DPM between 4 and 45 pct, depending on engine operating conditions. The report concludes that the DPM reductions were caused by the catalytic oxidation properties of a ferric oxide coating that developed inside the engine's combustion chamber. The ferric oxide coating also decreased gas-phase hydrocarbons and O, but it increased CO, and NO,. The increase in NO,, of about 12 pct, is considered the only adverse effect of the ferrocene-based fuel additive. The results suggest that the effectiveness of ferrocene was partially offset by increased sulfates because of the high-sulfur fuel used. Recommendations for continuing fuel additive research are presented.

Jan 1, 1992

By A. E. Harak

To determine the retorting characteristics of a column of mine-run, ungraded oil shale ranging in size from fines to 5-ton pieces, a 150-ton batch-type retort was designed and constructed at the Bureau of Mines Laramie Energy Research Center, Laramie, Wyo. The retort vessel is 45 feet high by 11 ½ feet inside diameter, and is supported in a 95-foot-high steel superstructure. Mine-run shale from the Bureau of Mines facility near Rifle, Colo., assaying about 25 gallons of oil per ton, was used as the test shale. To date, 11 runs have been completed, and the results of the last 10 of these are reported. The effects of oxygen content of the retorting gas and the superficial gas velocity of the retorting gas on oil recovery from a column of mine-run oil shale were studied. In one run, the average particle size of the shale was substantially increased to determine its effect on oil yield. Oil recoveries ranged from a low of 39.3 to a high of 65.8 volume-percent of Fischer assay.

Jan 1, 1974

By L. D. Gent

This report reviews the current state of the art of remote control techniques for underground continuous miners. A delineation of aspects requiring additional data is presented. Also a summary and delineation are presented in overview form for the related section functions: roof control, haulage, ventilation, power supply and rock dusting. The automated remotely controlled continuous miner project is a long-range research effort. However, the program has been divided into intermediate steps resulting in incremental production increases throughout the program. Data are developed relating the impact of our proposed research and development accomplishments to potential productivity impact.

Jan 1, 1975

By Gerald H. Groenewold

Reclamation of surface-mined landscapes is commonly defined only in terms of biological productivity. Other critical concerns associated with surface mining include the long-term quality of groundwater and stability of the postmining landscape. Meaningful reclamation design must address all these concerns. Reconnaissance of postmining landscapes indicates that three types of instability occur in these settings. These include: area-wide settling, localized collapse, and piping. Area-wide settling is most pronounced during the first year after contouring but appears in precontouring valley areas where frozen materials are contoured with a dozer. Although severe in some settings, development typically ends within one year. Piping appears to be a severe and long-term problem in some settings. Piping usually begins soon after contouring ceases and may continue for several years. In some postmining landscapes, piping has only started to develop after as many as five years of apparent stability. Piping is controlled by a combination of physical and chemical conditions in the spoil. A key factor is the presence of highly dispersive materials in the near surface. The design of a stable postmining landscape requires the integration of severe critical factors. These include: 1) detailed knowledge of the distribution of overburden materials with emphasis upon the delineation of highly sodic sediments; 2) proper equipment selection; and 3) a consideration of climatic factors. For reclamation to be successful, it must consider the entire landscape, not merely the soil zone. Any approach short of this will lead, at best, to temporary solutions.

Jan 1, 1980

By Anthony E. Szczuka

The purpose of this design note is to document the data that has been received from manufacturers, coal companies, training centers, government agencies, etc., that pertains to the completion of the Concept Feasibility Study For Training Equipment Designed to Improve Coal Productivity. Revision A documents additional data that has been received. ACKNOWLEDGEMENTS We wish to express our appreciation to the companies, mines, government agencies, unions, and contractor agencies listed herein that furnished the documented data. In most cases, it was furnished willingly and free of charge. In the few cases where the data was purchased, MDEC IRAD funds were used.

Jan 1, 1976

By Steven W. Schmauch

The U.S. Bureau of Hines conducted e mineral resource survey of approximately 232,000 acres in part of the Humboldt National Forest, Nevada, during 1989. About 7S percent of the study area was covered with mining claims. About 1,800 samples were collected end analyzed for 16 elements. Geologic structure, including thrust faults, is the most important factor in the localization of mineral deposits in the study area. The Independence mine (formerly Jerritt Canyon), Big Springs, and Wood Gulch are the most well known active properties, all developed on large, low-grade, disseminated gold deposits. These deposits have produced almost 3 million ounces of gold and are known to contain more than 8 million ounces of gold. At least 10 barite deposits in the south end of the range have had significant past production and contain 0.2 million tons of resources. Numerous precious and base metal targets have been identified and in some cases quantified during this study.

Jan 1, 1992

By John C. Machisak

INJURY EXPERIENCE AND EMPLOYMENT DATA on all stone quarries and associated plants in the United States are presented in this publication for the calendar year 1959. Such related operations as the manufacture of cement and lime and rock dressing are included. Data on clay and sand and gravel operations are not included and will be found in other Bureau publications on injuries and employment. The Bureau is authorized to make requests for such data and the information voluntarily submitted by the operators contributes to the promotion of safety in the quarrying industry. Every effort has been made to make this canvass as complete as possible. Data for production workers and office employees at the quarry site are included.

Jan 1, 1963

By John C. Machisak

INJURY EXPERIENCE AND EMPLOYMENT DATA on all stone quarries and associated plants in the United States are presented in this publication for the calendar year 1959. Such related operations as the manufacture of cement and lime and rock dressing are included. Data on clay and sand and gravel operations are not included and will be found in other Bureau publications on injuries and employment. The Bureau is authorized to make requests for such data and the information voluntarily submitted by the operators contributes to the promotion of safety in the quarrying industry. Every effort has been made to make this canvass as complete as possible. Data for production workers and office employees at the quarry site are included.

Jan 1, 1963

By John E. Conley

Of the three chemical elements most vitally essential for plant growth the United States, before World War I, had developed ample domestic supplies of but one-phosphorus. During and shortly after the war period, the fixation of nitrogen was greatly expanded in this country, as in many others, insuring a supply adequate for agriculture as well as for munitions. However, in spite of a search for sources of the third element, potassium, which began years before the war, attained almost frantic intensity between 1914 and 1919, and continued for 10 years thereafter, it was not until 1921 that the American Trona Corporation put its Searles Lake operations into continuous production. This company in 1926 became The American Potash & Chemical Co. but has never supplied much more than 15 percent of the potash consumed in the American market. Likewise, though discovered in 1921 in drill cuttings from oil wells, it was not until 1926 that domestic deposits of potassium salts adequate to render the United States independent of foreign sources of supply were proved to occur in the Permian Basin of Texas and New Mexico.

Jan 1, 1944

By F. J. Perzak

The Bureau of Mines conducted a flammability study of plastic ventilation ducts. Six rigid 16-in-diam fiberglass-reinforced plastic ducts from five manufacturers were examined using laboratory-scale, large-scale, and full-scale fire tests. The laboratory-scale tests included the American Society for Testing and Materials E162 radiant panel test, the E2863 oxygen index test, and the standardized small-scale flammability test (S3FT) developed by the Mine Safety and Health Administration (MSHA), U.S. Department of Labor, and replicated by the Bureau of Mines. Ten-foot lengths of the same ducts were also subjected to a large-scale vertical fire test, and 20-to 30-ft lengths were tested in a full-scale in-mine fire test at the Bureau's Lake Lynn Laboratory mine. The data from the laboratory-scale radiant panel test and oxygen index test indicated that the ducts were fire-resistant, However, five of the six ducts failed the S3FT and vertical fire tests, and four of the ducts failed the full-scale in-mine tests with flame propagation rates that ranged from 3 to 10 ft/min. The results indicate the need for improved fire-resistant plastic ducts. The good agreement between the S3FT re-sults and the vertical and full-scale tests show that the S3FT provides a good indication of the flammability of fiberglass-reinforced plastic ducting under realistic fire conditions.

Jan 1, 1987

By N. M. Safaya

Moderate to acute deficiency of plant available phosphorus is very common in western coal mine spoils and topsoils. Although some of the spoils are known to contain seemingly adequate amounts of total phosphorus, the plant available phosphorus is so low that it constitutes a serious plant growth limiting factor in the mined lands. For the revegetation of these spoils, the use of species, varieties and ecotypes exhibiting greater efficiency for P uptake and utilization, or conversely, lesser susceptibility to P deficiency would be highly desirable. To identify such plants, quick and adequate methods of screening germplasm should he available. In the present growth chamber study several plant species were screened using continuous flow culture and spoil culture systems to provide information on their relative susceptibility. In flow cultures, P was maintained at 0.25, 2.5, and 25 moles; while in spoil cultures it was applied at 0, 25, and 75µg/g to a P-deficient spoil. Phosphorus deficiency symptoms appeared in alfalfa cultivars, birdsfoot trefoil, emerald crownvetch and yellow sweetclover within 7-10 days upon transfer of their seedlings to U.25 or 2.5 µM P solutions. Burning bush and Russian thistle, found abundantly as pioneering species on mine spoils, showed no deficiency symptoms; their shoot dry matter yield in the 0.25µM P treatment was 24% and 36%, respectively of their maximum yield obtained with 25 µM P. However, the percent increase in the dry matter yield of legumes with 0.25 µM P ranged from 7-13% over their maximum yield. With the increase in solution P concentration, the root dry weight ratio in the legumes increased from an average of 0.22 to 0.43, while in the weeds from 0.14 to 0.30. The low susceptibility of Russian thistle to P deficiency was also demonstrated in the spoil culture experiment. Legumes showed greater response to P-fertilization on the spoil than did the two weeds. With increasing concentrations of P in the solution, the root weight ratio of all the species decreased. At 25 µM P, weeds invested only 14% of their total dry matter yield in the root fraction, where as legumes and grasses invested as much as 24% and 33% respectively. Weedy species averaged higher P concentrations than the legumes and grasses. The mean P concentrations of alfalfa cultivars were the lowest among legumes. In general, P concentrations increased with the increase in P supply. In the flow culture system, P supply increased the Ca levels of legumes. The mean Mn concentrations were highest in the weedy species. The increases in P supply decreased Zn levels in all of the species. File effects of P fertilization on the tissue concentrations of Mn and Zn in spoil culture were similar to that of flow culture system. From this preliminary study, it may be concluded that the continuous flow culture system is efficient in rapid screening of a large number of species under controlled conditions for their efficiency in adapting to mineral stresses.

Jan 1, 1982

By Floyd G. Anderson

A study was made of the effectiveness of dust-control methods being employed in connection with continuous-mining operations. Airborne dust exposures of workmen and dust loadings of return air were determined for six types of continuous-mining machines. The conditions required for control of dust exposure are summarized and include ventilation of the working face by an exhaust system. Return-air dust loadings ranging up to 13 pounds per hour are reported.

Jan 1, 1963

By J. T. Popp

This Bureau of Mines study reviews the geological factors that affect methane in the Beckley coalbed in southern West Virginia, including overburden, coalbed structure, type of and changes in lithology above and below the Beckley coalbed, and presence of fractures in the coal and rock adjacent to the Beckley. Depending on the depth, the Beckley coalbed emits from 216 to 520 ft3 of methane per ton of coal mined, and the Bureau estimates that methane emission in a deep, extensively developed mine in this area may exceed 3,000 ft3 per day per ton of coal mined. Average face cleat and butt cleat trends in the Beckley coalbed measured underground are N 33° W and N 53° E, respectively. Close cleat spacing con¬tributes to the friable nature of the Beckley and provides easy movement for methane and water. Because rider coals, splits, and carbonaceous shales may contribute methane to mine emissions, predictions of methane emission based on gas content of the Beckley coalbed alone may be conservative. Beckley coalbed reserves in the study area are 234 million tons. The gas content of the Beckley coalbed averages 407 ft3/ton, and the coalbed gas reserves are 108 billion ft3.

Jan 1, 1976

By Stanton L. Tainter

As a part of a wartime program to aid in the development of known ore bodies and in the discovery of hitherto unknown deposits of strategic minerals, the Bureau of Mines investigated the feasibility of diamond-drilling the Christmas copper deposit, in Gila County, Ariz., to increase the reserves of milling ore. Upon recommendation of the examining engineer, drilling was begun in September 1942, from the bottom (770) level of the mine. One month later, in cooperation with the Bureau, the Federal Geological Survey started geologic mapping of the mine workings. Since extensive and costly development would be required, the War Production Board concluded that ore below the bottom level could not be mined at that time because of the wartime shortages of equipment and man-power. In January 1943, drilling was moved to the 300 and 400 levels to locate reserves readily accessible for continued production of fluxing ore. This drilling, which was under the supervision of L. G. Marshall, was completed in January 1944.

Jan 1, 1948

By E. D. Gordner

Irrespira ble gutses issuing from the rock fofflb tions ere tJ source of expense ond danger in some metGLl mines. There is a great Variation in the compos i-· tion of such gdses and, os shown 'by recent sampling by the Bureau of ines, the gas rr;;,.y consi$t mostly ct carbon dioxide, (Rocle Strata Gtsses in the Mines of the East Tintic Mining District, by G. E. McElroy, Bu.retau of Mines Serial 2Z75) or f methone (Metruine in Ccalifornia C.old Mines, by B. 0. Picl-Q:lrd i:lnd !.. D. ("iordner, Bure, cf Mines Serial 2303), or nitrogen, sin the present instonce. A nl.liilber of unventilated rt:t.ises in some of the mine of l:l Neva&. district conuin «i'ccumulCltions of l;i hih-nitrogen gas the1t will not supi:ort life or combus­tion. The rdises ore in different geologiecil formations and in widely sep1:1rated. loecslities in the mining district. One ot" two ri::lises in the sme fc.rtr.ation may be full of the gos cand einother nec-r'by be t'ree ot· it. Lives have been lost t:lnd a number of men heave been overcome on enteing unvetilated rtsises in which their­respircable tss hcsd c1ccuni..1.l1::1ted between sldfts. Gener1:1lly, however, the gas see:ns to noozett from the .t'onrbtio:1 ond to ecc1: .. ,i.-1,;.1:.1te so slowly tMt its presence is not suspected t the tfr.1e, bu.t discovered. ed:'t&.c' the raise is t)band.oned. OcCE.isionelly 1 t issues from a ne•.,ly cut cre·tice or fissure under considerca ble pressure and in lar!?e enough '3.'16ntities to overcome or drive 011t men working in unventilated places.

Dec 1, 1922

By J. H. Holden

Operations involving the processing of coal, oxygen, and steam into synthesis gas by means of two pressure-type gasifiers have demonstrated the effect of heat loss and operating variables on carbon gasified and oxygen and coal requirements. Carbon gasified is the fraction of carbon in the coal that is converted to gas. Oxygen and coal requirement is the quantity of each that is needed to produce a unit volume (M std. c.f.) of carbon monoxide and hydrogen. Operating pressure of the gasifiers ranged from 150 to 300 p.s.i.g. and coal was fed at 200 to 500 lb./hr./cu.ft. of reaction-zone space. Oxygen-to-coal ratios were 8.5 to 10.5 std. c.f./lb. Heat loss and residence time have opposite effects on carbon gasified; increasing the heat loss decreases the carbon gasified, but increasing the residence time (by raising the operating pressure or reducing the coal-feed rate) increases the carbon gasified. The effects of these two factors are difficult to separate because they usually change simultaneously. A comparison of the results obtained from the operation of two gasifiers with different levels of heat loss, however, permitted the effect of heat loss to be separated from that of pressure and coal-feed rate. When the results were deter- mined on the basis of constant heat loss, increase of the residence time increased the carbon gasified until the reaction virtually had come to completion. For example, at 150 p.s.i.g., decreasing the coal-feed ratio from 500 lb./hr./cu.ft. to 200 lb./hr./cu.ft. substantially increased the carbon gasified. At 300 p.s.i.g., however, changing the coal-feed rate had little effect on the carbon gasified because the reaction had almost reached completion and further increase in residence time resulted only in a negligible change.

Jan 1, 1962

By Louis R. Iverson

Analysis of seed numbers present in topsoils (a grazed area, an ungrazed area, and two stockpiles) indicated that seeds of the most prevalent colonizers (e.g., Kochia scoparla, Setaria virdis, and Salsolo collins) were not present in the topsoil upon respreading but rather appeared by immigration from the surrounding areas. The grazed site had a seed density of over 7,700 seeds m-2 (of which 43% were from weedy species) and the ungrazed site had 3,900 seeds m-2 (of which 7% were weeds); the stockpiled topsoils had very low seed densities (255 and 520 seeds m-2). Seed densities and diversity decreased with depth on both the grazed and ungrazed sites; this was especially true on the grazed site where 94% of the seeds were found in the surface 7.5 cm. Several species were present in the seed bank (e.g., Hedeoma hispida, Artemesia ludoviciana, A. frigida, and A, abslnthlum) which were also found on the three and four year old mined sites in the aboveground vegetation survey. Seeds from these species may germinate after several years of dormancy, thereby starting populations on mined sites and enhancing plant diversity. Seed bank analysis was also undertaken on mined sites ranging in age of 2 to 6 years (plus an unmined site). Mined site seed densities ranged from 1630 to 3980 seeds m-2, with the four year old site having the greatest density (largely because of high Melilotus spp. populations); unmined site and stockpiled topsoil sample had lower seed densities. A significant positive correlation between total viable seed content and soil-water saturation percentage indicated that soil texture may influence seed viability/ dormancy (the. finer the material, the higher the seed population). As with the previous part of this study (and other studies), there was a poor correlation between the aboveground flora and the belowground seed composition.

Jan 1, 1982

By Matthew N. Rubin

This report summarizes the work performed under USBM Contract No. H0155155. The purpose of this work was to obtain operational data on retrofit noise control treatments suitable for use in coal preparation plants. This data was obtained by evaluating the performance of four categories of noise control treatments which were installed in a commercial coal preparation plant. The four categories of treatments were resilient screen decks, resilient impact pads, chute liners, and curtains. The selection, installation and initial evaluation of the treatments was documented in the Volume I report issued in 1977. This Volume II report summarizes the results of the long-term evaluation of the original treatments, as well as some additional tests which were conducted on elastomer-clad (resilient) screen decks. This project demonstrated the feasibility of a number of retrofit noise control treatments, some of which also proved to be quite durable over the long term.

Jan 1, 1982

By George S. Rice

The following paper was presented at an International Conference on Mine Safety Research held at Dortmund, Germany, September 23-28, 1935, inclusive. This conference was attended by representatives of Belgium, France, Germany, Great Britain, and the United States ands by invitation, Czechoslovakia, Poland, Spain, and Russia. The first international conference of representatives of mine-safety, research stations was held the United States Bureau of Mines Pittsburgh Experiment station in 1912 .4/

Jan 1, 1936

By J. F. McIlwain

The Bureau of Mines has investigated fumes generated by selected welding electrodes used in mines in order to help determine their relative health hazard potential. Fumes were generated and collected in an enclosed chamber for subsequent generation rate and chemical constituent determination. Shielded metal arc electrodes from the following groups were tested: AWS types E308-16 and E310-16 stainless steel, ECoCr-A Co-Cr hardfacing alloy, ENiCr Ni, an Mn-Cr buildup alloy, E7018 carbon steel, and EII018-M low-alloy steel. Flux-cored wire electrodes of this last group also were tested. Fume generation rates and the chemical composition of the fumes were measured. From these data, exposure in-dices were determined, which give a relative measure of the health hazard potential of using the electrodes. The effect of welding onto build-up alloy layers on the fume composition also was examined for five of the higher alloy groups.

Jan 1, 1987