Search Documents

By Lloyd A. Morley, Alan M. Christman

General Six open-pit metal mines, five copper and one molybdenum, were visited during the course of the research. Four were investigated twice, in summer and in winter, in order to determine the effects of seasonal variations In temperature and moisture upon the measured parameters, Permission to enter the fifth mine was received too late to make an examination during the summer months. The sixth mine was visited to confirm the results obtained from the other five and specifically, to observe how the project recommendations (as will be presented in this chapter) would apply to open-pit metal mines in general. Information gathered during the ten plant visits is sufficient to form an adequate data base for the report. A complete presentation of all field trip data is given in Appendix 1. Further, a detailed description of the electrical distribution and grounding practices at each mine is also contained there. Typical System. At a typical mine as shown schematically in Figure 62, one or more substations with resistance-grounded secondaries are employed to transform the incoming utility-voltage to the lower potential used by the mining machines, generally three-phase 4160 V. At this level, pit distribution is carried on overhead lines, supported by wooden poles, to supply switchhouses located in benches near the particular piece of equipment. A switchhouse is a small portable (often skid-mounted) structure at the termination of an overhead line which contains disconnect

Jan 1, 1976

By Wilton Johnson

Native asphalt was produced by four companies in two States, Texas and Utah. Bituminous limestone, used primarily as a paving material for street and road repair, was produced by one firm. R. L. White Co., Dabney Quarry, Uvalde County, TX. Gilsonite, a solidified hydrocarbon found only in Utah and Colorado, was mined by three firms: American Gilsonite Co., a division of Chevron Resources Co. (a subsidiary of Standard Oil Co. of California); Ziegler Chemical and Mineral Corp.; and Hydrocarbon Mining Co. (a subsidiary of Oberon Oil Inc., a Utah corporation), from properties in Uintah County, UT. Gilsonite is used for a variety of purposes including automobile bodysealer, light-weight aggregate for cement used in oil well drilling, asphaltic building board, protective coverings, anticorrosive paints, and roofing compounds. Gilsonite production in 1985 declined 57% owing primarily to reduced oil well drilling activity. The value per ton was essentially unchanged.

Jan 1, 1987

By Travis Rhoden

Merriam Webster?s Collegiate Dictio­nary (1996) defines team as ?a number of persons associated together in work or activity? and teamwork as ?work done by several associates with each doing a part, but all subordinating personal prominence to the efficiency of the whole? (page 1209). According to Dr. Geller, author of Building Successful Safety Teams: Together Everyone Achieves More (1998), a team of people working together for industrial safety consists of as few as two people or as many as fifteen who have complementary skills, assignments, or abilities for completing a particular task. Effective teams have members who share a common mission and relevant goals, and they share specific methods to reach their goals and accomplish their mission. They also have an evaluation system in place for holding themselves mutually accountable for goal-directed responsibilities.

Nov 1, 1998

By Thomas V. Falkie, R. Venkataramani

The empirical nature of this investigation required measurements of variables under operating conditions in underground coal mines. The variables to be measured were based on the postulated character¬istics of the loading function, as described in the previous chapter. One class of variables presumed to influence the loading function are geological variables. Accordingly, the sites for data collection were selected in different bituminous coal seams at dispersed locations in order that variation in geological conditions would exist. Seven mines in central and western Pennsylvania and one mine in northern West Virginia were selected as data collection sites. Five different coal seams were represented by these mines. The remaining classes of variables - geometric, mechanical, and procedural - were measured as they occurred in the mines. A description of the measurements, and the conversion of these measurements to forms which could be-analyzed for effect on the loading function is given. Mining Dimensions At the underground working face, the following dimensions were measured: a. Thickness of coal excavated. b. Thickness of shale excavated. c. Total height excavated. d. Width excavated. e. Depth of penetration of each machine cut. With the exception of the last of these dimensions, all were measured

Jan 1, 1972

By T. Estelle Gardner

The Bureau of Mines made enthalpy measurements on sodium bromide and sodium iodide in the temperature range 400° to 1,200° K using an ice calorimeter. Equations representing enthalpy as a function of temperature were derived from the data by the method of least squares. These equations were used to calculate smooth values of heat capacity, enthalpy, and entropy at 50° K intervals from the ice point to 1,200° K. The melting point determined for sodium bromide was 1,020° K; the melting point of sodium iodide was 934° K. The heats of fusion of sodium bromide and sodium iodide were calculated to be 6,270 and 5,680 cal/mole, respectively.

Jan 1, 1967

By D. Litton, H. Dobroski, J. G. Kovac

Since 1910, the U.S. Bureau of Mines (USBM) has investigated practical ways of dealing with the consequences of major fires and explosions in underground mines. The results of this research have had a significant positive impact on the mining community by enhancing mine workers’ chances of surviving an underground mine disaster. Today, the Bureau continues to conduct research in mine disaster mitigation. Much of this work has direct application to search and rescue situations, such as: emergency evacuation through smoke-filled or otherwise unbreathable atmospheres, locating and rescuing survivors from rubble piles, and fire fighting in confined spaces. Three USBM research areas are discussed: (1) Life Support -- This effort is directed toward research into and development of closed-circuit breathing apparatus for use in hazardous environments which are likely to be encountered in the aftermath of a mine disaster. (2) Trapped Miner Location -- A mine disaster may result in the entrapment of miners whose normal escape routes are cut-off. This research activity resulted in the development of transportable seismic technology that can be used to locate trapped miners. (3) Mine Fire Diagnostics -- This research involves developing practical techniques for remotely monitoring how the atmosphere inside a mine changes during a fire, in order to estimate the spread and severity of an underground fire. This information is critical in deciding how best to fight a mine fire, or whether it is safe to mount a rescue and recovery mission.

Mine closing methods should be carefully considered. If not properly sealed, an abandoned mine may continue to produce acid water. Since 60 to 90 percent of the total acid discharged from all coal mines is from abandoned mines,(58) some states require that provisions for sealing be contained in the mining permit application. Closing an operation to prevent harmful mine drainage into nearby runs and streams is a subject of much concern to states as a result of continuing problems from long abandoned mines which were improperly closed.

Jan 1, 1970

Continuously separate mixture of non-magnetic materials (such as scrap, precious metals, or certain ores) at a reasonable cost. Approach Nonmagnetic materials of different densities are rapidly float/sink separated by an augmented lifting force produced In a magnetic fluid (liquid) by the effect of an external magnetic field. The magnetic fluid is a colloidal suspension of magnetite In kerosene, prepared by a low-cost process. How It Works Separation is accomplished in an open trough filled with magnetic fluid. A magnetic field is established in the fluid, by energizing an electromagnet having poles on each side of the trough. Due to the design of the magnet poles and air gaps, the magnetic field is strongest at the bottom, about 10,000 oersteds, and uniformly decreases in strength to about 2,000 oersteds at the top of the fluid. Therefore, the magnetic field gradient increases with depth. The magnetic force attracts the entire separation medium (magnetic fluid) creating a reaction force of equal magnitude and acting in the opposite direction. This reaction created within a magnetic fluid/magnetic field combination is called a magnetic levitation force. It increases with the field strength. In this case because the magnetic field is strongest at the bottom of the trough, the magnetic levitation force will quickly float lighter material while heavier material sinks.

Jan 1, 1980

Improve safety at mineral operations that use cyanide leach solutions to recover precious metals from finely ground ores, Approach Provide an alternative, non-acidic means of cleaning processing systems such as the State-of-Maine filter system, thereby reducing the exposure of workers to toxic hydrogen cyanide gas (HCN), The Problem Many gold and silver mining operations use cyanide solutions to dissolve gold and silver from ores. The precious metals frequently are recovered from pregnant leach solutions by the Merrill-Crowe recovery process, whereby gold and silver is precipitated with zinc dust. When that method is used, suspended particles in the leach solution must be filtered out before zinc precipitation can occur. This filtering is accomplished with small packaged plants, such as the State-of-Maine (SOM) filtering system. Unfortunately, the filters become clogged with calcium carbonate scale after about 2 to 10 days of operation and must be cleaned before further precious metals recovery operations can continue, Cleaning the system is a hazardous task because the acid is not compatible with the alkaline cyanide leach solutions, and toxic hydrogen cyanide (HCN) gas may be produced when the acid and solution are mixed. That gas, if breathed or contacted with the skin, can cause cyanosis which may induce nausea and even asphyxia and death. To reduce this danger, the Bureau of Mines has devised a safer method of cleaning clogged filters,

Jan 1, 1986

By Donald R. Irving

THIS CHAPTER is new to the Minerals Yearbook and will appear regularly hereafter. Its purpose is to present statistics that reflect technologic trends in the minerals and metals industries (except fuels). Much useful information has been collected annually through the Bureau of Mines mineral commodity and employment and injuries canvasses. However, these data must be supplemented by further data to permit evaluation of the type, direction, and rate of technologic change, which are vitally important in long-term mineral planning. In addition to, and fully as important as, expanding the available data is the need to ascertain that the various items collected are obtained from identical reporting units, to enable direct comparisons to be made.

Jan 1, 1960

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

Air Moving and Conditioning Association, Fan Application Manual Part 1, Fans and Systems, AMCA Publication 201, 1976a. Air Moving and Conditioning Association, Fan Application Manual Part 2, Troubleshooting, AMCA Publication 202, 1976b. Air Moving and Conditioning Association, Fan Application Manual Part 3, Field Performance Measurements, AMCA Publication 203, 1976c. Air Moving and Conditioning Association, Directory of Products Licensed to Bear the AMCA Certified Ratings Seal, Edition 27, August 1, 1975. Allan, A. L., Hollwey, J. R., and Maynes, J. H. B., Practical Field Surveying and Computations, American Elsevier Publishing Co., Inc., New York, 1968. American Society of Heating Refrigeration and Air Conditioning Engineers Std. 51-75, Air Moving and Conditioning Association Standard 210¬74, Laboratory Methods of Testing Fans for Rating. Anderson, T. C., and Nugent, J. W., "Mine Ventilation Pressure Differentials with a Programmable Hand Calculator," MESA Informational Report 1050, 1977. Atkinson, J. J., "On the Theory of the Ventilation of Mines," Trans. N. E. Inst., Vol. 3, 1854, pp. 118. Barnes, E. L. S., "Mine Ventilation Network Analysis," International Mine Ventilation Congress, Marshalltown, S. Africa, Sept., 1975. Boshkov, S, and Amontree, B., "How Operator Proximity Affects Anemometer Readings," Coal Age, Vol. 55, No. 5, 1950, pp. 85-56. Boshkov, S., and Wane, M. T., "Errors in Underground Air Measurements," Mining Engineering, Vol. 11, No. 7, November, 1955, pp. 1047-1053. Briggs, H., "The Underground Leakage of Air, Investigation of the Porosity Coefficient," Transaction of the Institution of Mining Engineers, Vol. 82, pp. 111-121. Brown, J. R., and Hinsley, F. B., "The Flow of Air in Bends and Straight Airways," Transaction of the Institution of Mining Engineers, Vol. 116, July, 1957, pp. 845-867. Burrows, J., "Measurement of Fan Pressures," Journal of the Mine Ventila¬tion Society of South Africa, Volume 27, No. 4, April 1974, pp. 57-63.

Jan 1, 1977

Provide low-cost fire protection for big bulldozers. Approach A fire protection system, previously used on mobile logging equipment and adapted to surface coal augers, has now been adapted for use on large mining bulldozers. How It Works Heat sensors mounted in the engine compartment and hydraulic hose areas detect the fire, usually before the operator does. This causes the system to automatically discharge A-B-C class dry chemical extinguisher through a fixed piping system. The system can also be manually activated from either the opera-tor's cab or ground level. Location of the principal components of the system are shown in the drawing The heat sensors of the sys-tem consist of bimetallic strip switches which operate at about 10000F temperature. Switch operation results in release of compressed gas from a small storage cylinder. The gas expands to blow the dry chemicals out of the nozzles, in a spray that lasts about 15 seconds. The compressed gas used is usually nitrogen, although carbon dioxide is also used.

Jan 1, 1978

By M. A. Trevits, S. W. Lambert

In this Bureau of Mines investigation, production was monitored for 1 year at over 30 coalbed gas-drainage boreholes located in Alabama, Pennsylvania, and West Virginia. Results indicate that the quality of data gathered from such wells can be improved greatly if potential problems are anticipated and prevented in the early stages of well production. Major water-monitoring problems include solids buildup, freezing, the presence of gas in surface waterlines, and improper pumping interval settings. Such problems may be avoided by incorporating in the original well design waterline filters, sand screens, separator tanks, and systems to automatically control pumping intervals. Problems related to measurement of coalbed gas flow include large quantities of water vapor contained in the gas, especially during winter months; freezing and subsequent obstruction of flow; sudden, uncontrolled release of gas pressure; and solids buildup in metering equipment. The installation of commercially available items, such as filters, separators, and insulation, and the thoughtful application of a basic knowledge of coalbed gas reservoir characteristics will prevent most production-monitoring problems.

Jan 1, 1978

By Allen Q. Howard

An approximate solution to the electromagnetic boundary value problem consisting of a horizontal cylindrical conductor buried in a lossy half-space and excited by an arbitrarily oriented magnetic dipole is found using an iterative perturbation technique in a double Fourier transform space. This model is used to gain insight into the anomalous fields due to strong scatterers such as pipes or tracks which would be in close proximity to an EM mine rescue operation. The novel, three-dimensional aspect of the problem (i.e., the source) imposes the complexity that the current in the cylinder is not uniform. The field expressions are ideally suited to evaluation using FFT algorithm.

Jan 1, 1973

By E. W. Dean

The Bureau of Mines is engaged in the work of obtaining data regarding the physical and chemical properties of typical crude oils from the various producing fields of the, United" States. Preliminary reports have been published that cover the eastern fields* and the' Rocky Mountain districts.** Since the appearance of these, reports: it has been suggested that certain additional data. I regarding the samples would be of practical value. It was believed that a knowledge of the viscosity of crude oil was desirable, particularly in connection with the design and operation of pipe lines. In accordance with this suggestion, the authors have made viscosity tests upon as many of the samples of the two series as wore still available for examination. Determinations were made at temperatures of 70° and 100°F., and in addition the oils were Subjected to the A. S. T M, pour-test*** to as certain the lowest temperatures at which they remain in a fluid condition.

Jan 1, 1921

"""Hazard"" is the general expression used by safety engineers to denote risk, or the danger to property or human beings from the contingencies peculiar to different industries. Where a business, family, or individual is subjected to possible financial loss from any particular hazard, it is customary and is considered good practice to insure for reimbursement of possible loss. Accordingly, we take out insurance for earthquakes, for fire, for accidents, etc., and are charged a different premium for each. The premium rate is based on our relative exposure to the hazard in comparison to the total loss to our particular class of business in our geographical location over a given period.Insurance, then, must be considered as the experience of a group rather than of an individual, and any individual may be fortunate or unfortunate over stated periods. Through the law of averages, the probability of loss because of exposure to hazard is becoming more accurately measured as experience is accumulated and data are analyzed.Lion human life came to have a financial value in the eyes of the law, and employers were held liable for losses through accidents to employees while on duty, insurance companies began to underwrite the accident risks of the different employers and divided them into classes based on the amount of risk involved. Premiums for compensation insurance are based on relative exposure, which is measured by pay roll. The premium is rated in proportion to the severity of losses established by statistical studies.' It soon became evident that the accident experience of employers in the some industry varied widely; that is, there were good and bad risked in the same line of business. This resulted in ""experience rating"" of premiums, meaning thereby that an employer with experience in accident cost was premium rated in proportion to his losses over a stated period (usually three or more years)."

Feb 1, 1926

By Julie Mitchell, Robert King, Len Eros

The Bureau of Mines has studied the Deserado Mine computerized monitoring and control system, located in Rangely, Colorado, to acquire knowledge about the overall costs and benefits of mine monitoring systems. The Deserado system is a complex system monitoring environmental parameters, electrical power, and operation of all mine equipment, and controlling the entire conveyor haul age system. This paper discusses the evaluation of the Deserado monitoring system from initial design through system installation and operation. It also examines the costs, benefits, and performance of the monitoring system.

Tables

Jan 1, 1992

Develop methods of enhancing and measuring the high-temperature softening and melting properties of iron oxide pellets reduced under simulated blast furnace smelting conditions. Approach Add dolomite and Limestone flux and a low-cost organic binder, such as starch, carboxyl methylcellose (CMC), or waste papermill sludge, to the iron oxide concentrate to produce hematite (ferric oxide) pellets with superior high-temperature metallurgical properties. Simultaneous increases in softening temperature, gas permeability, and enhanced metallization rates are sought to improve blast furnace productivity and energy efficiency. Background In the past, bentonite, an inorganic binder, was the only additive (binder) used in the production of pellets made from iron ore concentrate. Research has shown that the reducibility of conventional (acid) pellets can be increased by the addition of flux or an organic binder. The increase in pellet reducibility results in less wustite in the center of the pellet at high temperatures, such as those obtained in the cohesive zone of the blast furnace.

Jan 1, 1990

Eliminate accidental tramming of a cleanup tractor. Approach A switch was installed in the operator's seat cushion to pre-vent the cleanup tractor from tramming without an operator in the driver's seat. How It Works The operator must be seated, and the Forward/Reverse Switch (that controls tramming direction) must pass through the NEUTRAL position before the vehicle will tram. See Figure 1. A pressure-sensitive seat cushion switch, a solid-state relay, and a double-contact relay were added to the control circuitry of an S & S BMUAT -88 cleanup tractor to create this tramming interlock. The weight of the operator on the cushion closes the seat cushion switch (Figure 2, A). This activates the solid-state relay (B), which completes the initial circuitry. Moving the For- ward/Reverse Switch (C) to NEUTRAL energizes the coil in the double-contact relay (D) and closes both contacts. One contact completes a sustaining circuit which keeps the double-contact relay energized. The second contact transfers power to the remaining contacts within the Forward/ Reverse Switch. These circuits are shown in greater de- tail in Figure 2.

Jan 1, 1978