Search Documents

By W. P. Diamond

It is estimated that more than 1 trillion cubic feet of methane is contained within the coals of the Mary Lee group in Jefferson, eastern Tuscaloosa, and southern Walker Counties, Ala. Most of this methane will be encountered by mining. Coals of the Mary Lee group are presently being mined at depths exceeding 1,000 feet and will in the near future be mined at even greater depths, where the problem of methane gas affecting the mining operations will be acute. It is calculated that approximately 90 pct of the methane is at depths greater than 1,000 feet, and over half of the gas is contained within only 12 pct of the study area which is under more than 1,500 feet of over-burden. Degasification in advance of mining will increase mine safety, reduce ventilation expenditures, increase productivity, provide an additional energy source, and make it possible to mine parts of deep coalbeds that probably could not otherwise be mined.

Jan 1, 1976

Modify conventional mining practices to reduce significantly the amount of material brought to the surface from underground mines, or to ?re-mine? existing surface mine dumps by backfilling empty underground stopes.

Jan 1, 1994

By R. L. Grayson, W. E. Wallace, M. D. Attfield, A. Q. Wearden, P. Bolsaitis, R. D. Kennedy, M. J. Keane, J. C. Harrison

"Respirable high-silica particles from four coal mines. a clay mine and a tunnelling site were analysed for silicon vs aluminum composition by performing scanning electron microscopy-energy dispersive X-ray analysis (SEM-EDS) at electron accelerating voltages of 20 kiloelectron volts (keV). The same particles were analysed at 5 keV to determine possible differences in surface vs bulk composition. In some cases high-silica particles exhibited a decrease in the ratio of silicon to aluminium K-alpha line intensities with decreasing electron beam accelerating voltage. This behaviour is consistent with aluminosilicate surface contamination or occlusion of a silica particle. Some 20 high-silica particles were analysed from each of 10 samples. Powdered aluminosilicate glass was used as a control for the behaviour of silica with a homogeneous distribution of aluminium in the particle. Significant differences were found between the control and sample means for an Illinois bituminous coal mine dust, two western and one central Pennsylvania bituminous coal mine dust low-temperature ashes. and a clay mine and mill dust sample, but not for an anthracite coal mine dust and two central Pennsylvania bituminous coal mine dust low-temperature ashes. INTRODUCTIONRESPIRABLE dust quartz content commonly is measured on bulk samples by using i.r. spectroscopy or X-ray diffraction. For research purposes, individual particle-by particle SEM-EDS analysis at 20-30 keV electron beam accelerating potential may be used also. Such measurements have not provided an unambiguous association of quartz content with occupational pulmonary disease prevalence in exposed workers (WALTON et al., 1977). Rather, there is evidence that coal rank modifies the relationship between dust exposure and pneumoconiosis development (WAL TON et al., 1977; ROBOCK and BAUER, 1990; ATTFIELD and MORRING, in press). SEM-EDS analysis was performed to measure the silicon fraction, Si/(Si +Ai), at 20 and at 5 keV on high-silica particles to determine if some respirable quartz particles generated by mining exhibit heterogenous composition with depth (WALLACE et al., 1990), which might affect the bioavailability of the quartz surface."

Dec 1, 1995

This chapter defines light as a type of energy, and tells how different features of light are measured. It 1s important to understand the units of light measurement because they are used throughout the rest of the book. But more Important, this will help you to understand the "regs" and how to get the best out of the lighting you have available! By the time you complete this chapter, you should know what candle-power, foot-candle, and foot-lambert refer to, and you will also be able to tell why the helmet that the new miner wears appears orange to human eyes. Light that you "see" is really radiant energy that hits the retina of the eye. Radiant energy moves out from a light source much like a series of bullets from a number of machine guns being fired at the same time in all directions.

Jan 1, 1976

By Helen W. Lang

The Bureau of Mines has developed a very rapid gas chromatographic method for routine determination of oxygen, nitrogen, methane, and carbon dioxide in mine atmosphere samples. Analysis is accomplished in 3 min; readout appears on a single strip chart. The gas sample is split between two columns contained in separate chromatographs. A 5 A molecular sieve column separates oxygen, nitrogen, and methane; a porous polymer column separates carbon dioxide from an air peak. Direct selective analysis of methane from this unresolved air peak is accomplished using a hydrogen flame ionization detector (FID). Carbon dioxide is catalytically converted to methane and detected by FID.

Jan 1, 1972

By John P. Conway

This Bureau of Mines investigation was undertaken to determine the feasibility of lock-bolt support in Tertiary-gravel material. Pull tests were performed on five types of rock-bolt anchors to determine their optimum anchorage capacity. Four of these anchors are commercially available; the fifth, an explosive-anchor bolt, was developed by the Bureau of Mines. To increase anchorage capacity, epoxy grout was used with several of the commercial types of bolt. Tests showed that sufficient anchorage could be obtained by employing epoxy-resin grout with the commercially available wedge bolt, or by using the explosive-anchor bolt. Also estimated are bolt spacing and cost of a rock-bolt support system.

Jan 1, 1971

By P. Coleman, J. C. Kerkering, S. Iverson

Fault tree analysis is a systematic safety analysis tool that proceeds deductively from the occurrence of an undesired event (accident) to the identification of the root causes of that event. One recurring mine safety problem—a dozer falling into a void over a drawpoint on a coal surge pile—was analyzed using available, inexpensive fault tree programs on a personal computer. The analysis identified basic and intermediate events that led to the burial of the dozer and graphically depicted the interrelationship between these various subordinate events as well as the various chain of events leading up to the primary event. A sensitivity analysis on these probabilities showed which events had the greatest influence on dozer burial in a coal surge pile.

By Rimas Pakalnis, Tom Brady, Lewis Martin

A major focus of ground control research presently being conducted by the Spokane Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) is to incorporate weak rock masses (such as are associated with operations in the Carlin Trend in Nevada) into existing design relationships. The original database that led to most of the empirical design relationships presently employed in hard-rock mining was derived from fair-to-good-quality rock. In this study, the relationship between weak rock quality and opening design (non-entry/entry methods) is being investigated. The common factor in all mines is a weak back or wall. This work attempts to provide tools that will enable a mine operator to make economic decisions that will also ensure a safe working environment. Tom Brady (for correspondence - E-mail- thb6@cdc.gov)and Lewis Martin are at the Spokane Research Laboratory, National Institute for Occupational Safety and Health, 315 East Montgomery Avenue, Spokane, WA 99207-2291, USA (E-mail• ljm8@cdcgov); Rimas Pakalnis is at the Mining Department, University of British Columbia, Vancouver, British Columbia, Canada (E-mail: rcp@mining.ubcca).

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

RECOMMENDATIONS FOR FURTHER WORK Based on the development effort and full-scale tests conducted during this program, a number of technical areas for future research and development have been identified. Further work in these areas would help to improve the reliability, speed of operation and efficiency of the remote sealing system. Recommendations for future work are summarized as follows 1. Development of an Inert Gas Generator For the sake of expediency in conducting the field test program, fresh air was used as the fluidizing medium for the fly ash. However, in an actual mine fire application the use of fresh air is likely to be prohibited. An inert gas, such as nitrogen, carbon dioxide or air containing less than 8 percent oxygen would be required. Using combustion as a means of reducing the oxygen content of air appears to be an attractive solution to the generation of the high flow rates of gas required (2500 to 5000 scfm). Such an inert gas generator would serve a dual purpose for the overall fire extinguishing operation. First, it would provide the inert gas for fluidizing the fly ash. Second, it could be used for inerting the fire area after the seals had been placed, thereby reducing the time required to extinguish the fire. It is recommended that the Bureau undertake a program to develop a field-operable, inert gas generator to satisfy these two requirements. 2. Development of a Field-Operable Sonar Initial Probing System A first stage prototype of a sonar initial probing system was developed during this present program. The results obtained with

Jan 1, 1973

By Harold W. Lipper

Helium production and shipment reached new peaks in 1.361. The Bureau of Mines produced 727 million cubic feet, 13 percent more than the 1960 record, and shipped 552 million cubic feet, 16 percent more than the 1960 record. Production exceeded demand for the third successive year, enabling the Bureau of Mines to add 174 million cubic feet to the volume stored underground for future use. At the end of 1961, the total volume of helium in underground storage in the Clifside gasfield was 44-7 million cubic feet. Contracts to implement a long-range helium conservation program were completed with four companies, obligating all the contracting authority of $47.5 million a year made available by the Congress. The four companies will finance, build, and operate helium extraction plants to recover from natural gas an annual average of 3.1 billion cubic feet of helium that would ordinarily be wasted when the helium-bearing natural gas is used for fuel.

Jan 1, 1962

Develop a simple and practical technique to measure in situ rock mass properties for realistic design and stability evaluation of underground structures. Background The Bureau of Mines has developed basic principles and techniques to determine in situ rock mass properties including Poisson's ratio, deformation modulus, and yield and failure strengths. An instrumentation package consisting of three pressure cells is installed in a single drill hole. Cell pressure response data are acquired and used to calculate and determine the rock mass properties. How It Works A test hole of BX size (approximately 5.7 cm) or larger is drilled to the approximate depth of the measuring point. The last portion of the test hole is drilled with precision bits to EX size (approximately 3.8 cm). The instrumentation package, which consists of one 3.8-cm-diameter cylindrical pressure cell (CPC) and two 5.7-cm-diameter cement-capsulated, flat borehole pressure cells (BPC's), is then installed. A complete history of cell response to changing strata loads is acquired on a continuous basis with a chart-type hydraulic pressure recorder. From these cell pressure data, Poisson's ratios, deformation moduli, and yield and failure strengths are calculated and determined.

Jan 1, 1990

By C. Sunderman, J. Johnson, S. Signer

Researchers at the National Institute for Occupational Safety and Health have developed a miniature data acquisition system (MIDAS) that can measure resistance changes and temperature, store data for later retrieval, and illuminate LED lights. This instrument can be used with strain-gaged bolts, cable bolts, CSIRO stress-measuring gages, string pots, and any other instrument that uses single-ended, resistance-type gages. MIDAS has the capability to measure up to 16 gages at preset time intervals and store more than 2000 scans, yet is small enough to fit in a 35-mm hole. Because the MIDAS consumes little power, a 9-V alkaline battery will operate the system for 6 months. Data from the MIDAS can be sent to a PC via an RS232/RS485/IRdA port. A software program was written to set operation parameters, graph data, and store all information directly to a spreadsheet. Three LED lights change from green to yellow then red based on reading levels and/or rates of change. This feature can be used with different types of gages to warn miners of possible rock instabilities. The MIDAS has received MSHA experimental permissibility approval and is currently being tested at several mines.

By A. Wahab Khair

"Geologic materials emit transient noises when stressed /1/. The rate and pattern of these transient noises or acoustic emissions (A.E. hereafter) depend on the stages of deformation of the material /2/. It has been demonstrated that rock/coal fracture processes under stress consist of three distinctive stages--crack initiation, propagation and ultimate fracture--and that coalescence of numerous cracks leads to ultimate failure rather than the propagation of a single crack /2,3/. This paper presents an analysis of fracture formation in rock/coal specimens subjected to straight wedge indentors using A.E. technique.The effect of specimen geometry, wedge indentor angle, confining pressure, and material anisotropy on fracture type (tension, extension, and shear crack), fracture length, and fracture intensity were studied. Two types of material mainly Berea sandstone and Coal Berg No. 2 coal were used in this study. Prior to the experiment the mechanical properties of both sandstone and coal were determined using rectangular specimen (Figures 1 a) in standard compression tests and are given in Table 1. In this study cylindrical and rectangular specimens were first prepared to proper dimensions of 2 in. x 1.5 in. and 3 in. x 1.5 in. x 1.5 in. (5.08 cm x 3.81 cm and 7.62 cm x 3.81 cm x 3.81 cm), respectively and then instrumented with SR-4 strain gages as shown in Figure 1. The instrumented specimens were then tested under four distinct load boundary conditions as illustrated in Figure 2. During a typical experiment the instrumented specimen was placed in a specially designed loading jig (Figure 3) where a predetermined lateral pressure was applied mechanically to the specimen by adjusting the inner plate of the confining chamber via screw while monitoring strains in the specimen. Using rock/coal elastic constants and measured strains, a predeter¬mined lateral pressure was applied to the specimen. Then a vertical load was applied by the straight edge of a wedge indentor attached to the upper platen of the universal loading machine via ball and socket arrangement (Figure 4). The arrangement allowed uniform application of load in a straight line manner on the surface of the specimen. During the test a number of parameters namely strains, load and A.E. rates were recorded (Figures 5a-b)."

Jun 1, 1988

By Lloyd A. Morley, Alan M. Christman

1. Anonymous. "Getting Down to Earth," booklet 25T, James G. Biddle Co, Plymouth Meeting, Pa. (1970) pp. 1-48. 2. Anonymous. "Megger Ground Tester, Special Instructions," booklet 25-J-1, James G. Biddle Co, Plymouth Meeting, Pa. (1961) pp. 1-16. 3. AIEE Committee. "Application Guide on Methods of Substation Ground¬ing," AIEE Transactions on Power Apparatus and Systems (April 1954) pp. 271-277. 4. AIEE Committee. "Voltage Gradients Through the Ground Under Fault Conditions," AIEE Transactions on Power Apparatus and Systems (October 1958) pp. 669-692. 5. American Standards Association. "American Standard Safety Rules for Installing and Using Electrical Equipment in and about Coal Mines," U. S. Bureau of Mines Information Circular 8227 (1964). 6. Armstrong, H. R. "Grounding Electrode Characteristics from Model Tests," AIEE Transactions on Power Apparatus and Systems (December 1953) pp. 1301-1306. 7. Beck, Edward. Lightning Protection for Electric Systems, McGraw¬Hill, New York (1954) pp. 281-295. 8. Bellaschi, P. L. "Impulse and 60 Cycle Characteristics of Driven Grounds," AIEE Transactions (March 1941) pp. 123-128. 9. Bellaschi, P. L. "Lightning Strokes in Field and Laboratory," Elec¬trical Engineering, Vol. 58 (November 1939) pp. 466-468. 10. Bellaschi, P. L., Armington, R. E., and Snowden, A. E. "Impulse and 60 Cycle Characteristics of Driven Grounds-II," AIEE Tran¬sactions (1942) pp. 349-363. 11. Bewley, L. V. "Theory and Tests of the Counterpoise," AIEE Transac¬tions (August 1934) pp. 1163-1172. 12. Brereton, D. S. and Hickok, H. N. "System Neutral Grounding for Chemical Plant Power Systems," AIEE Transactions on Applica¬tions and Industry (November 1955) p. 315. 13. Bruce, C. E. R. and Golde, R. H. "The Lightning Discharge," Journal of the Institute of Electrical Engineers, London, Vol. 88 (December 1941) pp. 487-505.

Jan 1, 1976

By J. Brad Seymour, Mark K. Larson, Richard L. Rains, Douglas R. Tesarik

For several years, researchers from the Spokane Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) have been using geotechnical instruments in underground mines to study ground control problems and develop means of reducing accidents and fatalities caused by ground falls. This paper describes many of the different types of instruments, sensors, and data acquisition equipment that have been used for these studies; briefly explains the advantages and disadvantages of various sensor technologies; provides practical recommendations regarding the use of specific instruments and data acquisition systems; and outlines a general approach to the design and implementation of a successful instrumentation plan. A wide variety of instruments are commercially available for measuring deformation, strain, stress, and/or load. If used correctly, these instruments can provide important quantitative information regarding the mining-induced behavior of the host rock, the performance of ground support systems, and the safety and stability of underground workings. Data collected from these instruments can warn mine staff of impending ground control failures or hazardous working conditions, as well as provide valuable information for the design of ground support systems and the configuration and sequencing of mining excavations. We hope that the practical information presented in this paper will encourage a more widespread use of geotechnical instruments in underground mines and lead to reliable measurements that aid the engineering decisions affecting the safety of miners.

Jan 10, 2000

By F. R. Cattoir, D. H. Baker

Fused - salt electrorefining has been successfully applied to the purification of vanadium metal . The electrolyte used in this refining technique was sodium chloride to which had been added 3 to 6 percent vanadium as vanadium dichloride . The average deposition current efficiency was 91 percent . Oxygen and nitrogen , the impurities in commercially produced vanadium metal , were reduced by two - thirds of the amount contained in the feed material . Hardness of the vanadium- metal product was reduced from an initial 97 Rockwell B ( RB ) to a minimum of 35 Rg . The reduction of these impurities markedly improved the plasticity of the final product obtained by melting the crystalline cell metal into small ingots . These ingots could be given a 99 - percent cold reduction by rolling before edge cracking appeared . Growing interest in high - purity vanadium and the industrial need for purer metals and improved alloys for use under high temperatures and high speeds have demanded the elimination and/or control of impurities . Accordingly, research to eliminate or control the undesirable impurities has been expanded .

Jul 1, 1960

By Richard V. Ageton

"Everyone admits that there are more accidents in metal mines than there should be but there is much difference of opinion as to the causes of accidents, whether avoidable or unavoidable, and the amount of responsibility attaching to the miner and the mine operator, respectively. However, it seems that one of the main reasons why there are so many accidents, is that there is so little general knowledge regarding their causes and costs. Some information regarding the costs and causes of metal-mine accidents is presented in this paper.The data contained were obtained from a study of the complete accident and medical reports of two large metal-mining companies, which carry their own insurance. Path maintain hospitals with competent medical attendants. One of these companies also maintains a very efficient safety bureau, consisting of a safety engineer, with two assistants who work in connection with the medical department, and with the safety committee made up from among the miners themselves.Daring the year of 1920, ""A"" Company employed approximately 900 men, and these men worked more than 270,000 shifts. There were 373 minor and major injuries, among these 900 men, hence assuming that each injured man was hurt cut once, 41 per cent of the men who worked in this mine received some kind of time-losing injury during the year. On account of these injuries the injured men lost 3731 shifts, and thus the time lost due to injuries amounted to approximately 1.4 per cent of the total number of shifts worked,"

Oct 1, 1923

Objective A cable bolt can be a strain-measuring device as well as a supporting device in underground mines. Placing instruments on a cable bolt allows certain characteristics of a rock mass, such as high strain and load, to he evaluated during mining and provides a means for mining engineers and mine inspectors to forecast a potential roof fall. Background Thousands of cable bolts are installed in U.S. mines each year. Studies performed by NIOSH researchers show that support loads can exceed the yield point of the steel, which can result in unstable ground conditions that pose direct safety hazards for underground workers. Rock falls can also create secondary hazards, such as caved escape ways and blocked ventilation passages. Development of methods and tools to assist in the evaluation and selection of rock supports could reduce the number of unplanned rock falls significantly. Approach Instrumented cable bolts developed at NIOSH’s Spokane Research Laboratory were used along with existing ground control systems to monitor rock mass loads and movement Axial and shear loads on the cables are determined as these loads are transferred to strain gages embedded in the king wire. In longwall, room-and-pillar, or underhand cut-and-fill mines, rock mass loads and movements can be detected down to microstrains of stress or millimeters of movement. By detecting such small amounts of ground movement and support load, early intervention to prevent a roof fall is possible, and miner safety and health are increased. How it Works Up to 10 strain gages are embedded in the king wire at whatever locations a mine ground control engineer may specify. The gages m either be set in pairs in the same plane to detect shear or set at 90° angles to detect loading in three dimensions. The cables are up to 5 meters long if they arc to be grouted with resin or up to 15 meters: if they will be grouted with cement. They arc capable of holding m ultimate lend of 214 kN and produce reliable readings to 178 kN, as shown in the calibration curve. The cables are fitted with an instrument plug for monitoring the gages and a special head for insertion into the rock. A data acquisition system, such as a Vishay strain indicator box, Campbell Scientific, or Omnidata system, is required to obtain the data for load and displacement calculations.

Nov 1, 1998

By H. L. Gibbs

A portable radon monitoring instrument capable of making on-the-spot measurements of the radon gas content of uranium mine atmospheres was designed and constructed. The monitor was tested in the laboratory and in operating uranium mines. Good correlation was obtained between the monitor readings and radon measurements made on mine atmosphere samples taken in radon bottles.

Jan 1, 1973

By Peter N. Gabby

A mineral survey of 8,300 acres of the 24,980-acre Burnt Creek Wilderness Study Area (ID 45-12), was conducted by the U.S. Bureau of Mines in 1985 at the request of the Bureau of Land Management. The study area is located in Custer County, ID, 90 miles northwest of Idaho Falls. No mines, claims, or prospects are in the study area. The northern half of the study area and adjacent lands to the north, northeast, and east are or were recently under oil and gas lease, Basalt and latite-andesite of the Challis Volcanics predominate in the study area. Several hundred feet east of the study area is a quarry in talus of Mississippian-age limestone that was used for sized 100-pound rock fill in the Old Dry Creek Reservoir dam. Two samples, one taken at the quarry and the other at a limestone outcrop on East Fork Burnt Creek, have CaC03 content in the range of 90 to 95 percent, and is suitable as the limestone component of Portland cement, However, limestone outside the study area could supply foreseeable demand. Lead- silver mineralization has been observed in Paleozoic carbonate rocks elsewhere in the Lost River Range, but these rocks do not occur in the study area.

Jan 1, 1986