Search Documents

By H. C. George

This report presents a comprehensive tabulation of lifting cost data collected from oil companies in many different fields. These data were collected during the writer's studies of surface equipment and methods of pumping oil wells, in practically all of the important oil fields in the United States and are based on average operating conditions at 57 groups of properties with a total of 4,497 producing wells. Although lifting cost is only a part of the total cost of producing oil, it nevertheless gives a representative cost figure for purposes of comparison.

Jan 1, 1923

Reduce potential for steering errors during tramming of articulated vehicles, particularly when the operator is seated to the rear of the machine pivot point and is tramming in reverse. Approach Position-sensing and feedback cylinders were applied to the steering cylinders of two S&S cleanup tractors to cause the steering-control lever to match the orientation of the vehicle sections. The vehicles were tested in two working mines. How It Works A position-sensing cylinder (see Figure 1, Item A) is attached to one of the steering cylinders in the cleanup tractor steering system. As the steering cylinder piston rod is actuated by movement of the control lever, hydraulic oil flows from the position sensing cylinder to the feedbck-cylinder (B), causing the feedback-cylinder piston and rod to move. The outside end of the rod repositions the the steering-control lever until its angular position corresponds to the orientation of the vehicle sections.

Jan 1, 1978

By F. W. Penn

An aircraft auxiliary power unit (APU) was used as an exhaust source for evaluation and refinement of sampling and analytical procedures for gas turbine engines. The unit was also used to determine the emission characteristics of APU's in service and to study the effect of fuel composition and combustor design on exhaust emissions. Carbon monoxide, carbon dioxide, oxides of nitrogen, hydrocarbons, aldehydes, particulate loading, and odor were measured at engine operating modes representing the duty cycle encountered in airline operation. Analyses showed good repeatability, and adequate sensitivity was attained in these experiments. Smoke opacity measurements were not taken owing to the lack of a high-sensitivity smokemeter. Results showed that the minimum emission levels occurred with the standard combustor and Jet A fuel. Emission rates were highly dependent on test mode, but emission patterns as a function of test mode were similar for all fuels and combustors tested. A comparison of three identical design production combustors showed a variation in average emission rates of less than 5 pct.

Jan 1, 1973

By Howard E. Parkinson

An environment monitoring and communication system has been installed in the Bruceton Mine, and research is under way to improve mine safety. Standard day-to-day mine communications are available, along with additional systems installed to permit experimentation with wireless radio, through-the-earth phones, along-the-roof paging, and mine face machinery communications. Research is continuing and the essential concepts for a dependable whole mine communication system, providing simple environment monitoring, improved day-to-day communications and post-disaster communications, will be demonstrated in a larger mine with about 900 feet of overburden.

Assure fail-safe stopping of a mining vehicle immediately following a loss of electric power. Approach A separate emergency brake system which actuates when electrical power is interrupted, was installed on several mining vehicles and tested in a long-term underground mining demonstration. How It Works Separate, spring-actuated brakes, which press against brake discs, are used to stop the vehicle following power failure. To allow norm al movement of the vehicle, hydraulic oil under pres? sure from the vehicle's hydraulic system is directed to a spring? loaded piston in each emergency brake housing. That pressure causes the piston to compress the spring and relieves the spring pressure against the puck, thereby allowing the brake disc to turn freely. See Figure 1 A. If the electrical power fails or if the machine is turned off, a valve in the hydraulic line to the emergency brakes opens. That valve, shown as ?Solenoid Valve (automatic)" in Figure 1, which is normally held closed by its electrical solenoid while the vehicle is electrically powered, is opened by the spring in the valve assembly. The pressure in the hydraulic line which is connected to the emergency brakes then drops to

Jan 1, 1978

By E. G. King

Enthalpy increments above 298 K were determined by the Bureau of Mines for magnesium hydroxide (brucite) between 298 and 900 K by the method of drop calorimetry. Enthalpy and entropy increments from this investigation were combined with other data from the literature to calculate absolute entropies, free energy functions, enthalpies of formation, Gibbs energies of formation, and equilibrium constants of formation from 298 to 900 K. By the use of published PVT data for water, a table of Gibbs energy change was given for the reaction MgO (periclase) + H2O = Mg(OH)2 (brucite) as a function of temperature and pressure.

Jan 1, 1975

By L. C. Marchant

Results of detailed analyses of four cores from the Threemile Canyon area in the P. R. Spring tar sand deposit in Utah are reported by the Bureau of Mines. The cores were obtained by the Utah Geological and Mineralogical Sur-vey as part of a l7-corehole evaluation program in the P. R. Spring, Hill Creek, and Rim Rock tar sand deposits. Average properties of the oil zone in the Threemile Canyon area as deter-mined from these cores are as follows: Oil saturation, 67.4 pet of pore volume; porosity, 29.2 pct; permeability before oil extraction, 133 millidarcies; and permeability after oil extraction, 2,855 millidarcies. Average net thickness of the oil zone is 23.8 ft and average depth to the top of the oil zone is 189 ft.

Jan 1, 1974

Although haulage truck collisions account for only a small percentage of haulage accidents, the likelihood of severe injury, or even death is very high when such a collision does occur. Most rear-end collisions also result in considerable equipment damage, creating a need for expensive repairs. To improve collision protection, some southwestern surface mines have, for several years, been fabricating and using extended bumpers. In cooperation with these mines, the Bureau of Mines has worked to improve this technology by evaluating the structural requiremnts of extended bumpers. How Extended Bumpers Help The Bureau found that when one large rear-dump haulage truck collides with the rear of another an extended bumper protects the driver of the vehicle that is struck by dissipating the impact energy into the rear tires and pushing the whole vehicle forward. An extended bumper also prevents the box on the truck that is hit from penetrating the cab of the other truck-a typical and serious collision hazard. A further advantage derives from the wide design of the extended bumper which helps prevent damage to truck ladders, thereby minimizing any entry or exit problems. Extended bumpers also provide safe work platforms at the front of large haulage vehicles.

Jan 1, 1984

By J. H. Weber

This Bureau of Mines publication describes the hardware system and software package for the semiautomatic acquisition and automatic processing of high-resolution mass spectrographic plates. The semiautomatic data acquisition allows a tenfold saving of time compared with manual data acquisition. Automatic processing of the high-resolution data to yield exact masses, intensity, and the corresponding empirical formulas is accomplished by efficient programming on a small, inexpensive, programmable calculator system.

Jan 1, 1974

By Peter F. Steidl

Seven degasification wells have been completed in the Pittsburgh coalbed at the new Emerald mine near Waynesburg, Pa. Funding was provided by the Bureau of Mines to perform stimulation treatments on five of the wells, to show that this is a feasible and economical means of degasifying part of a coalbed. The seven wells ranged in depth from 590 to 910 feet. Stimulation treatments used 25,260 to 42,660 gallons of foam and 7,400 to 12,800 pounds of 20/40-mesh prop sand. Pumping rates were 10.8 to 11.6 bbl/min and treating pressures were from 1,050 to 1,600 psig. On the day following stimulation, gas production ranged from a few hundred cubic feet per day to more than 100,000 cu ft/day.

Jan 1, 1978

By Aarne Visnapuu

Pneumatic chipping, scaling, and grinding can expose the tool operator to noise levels in the range 90 to 120 dbA. In most chipping and scaling operations, casting resonance is the primary source of noise, followed by air exhaust, and machine and chisel resonance. In grinding, the air-exhaust noise predominates. The Bureau of Mines has shown that noise from these operations can be reduced by up to 15 dbA. Workpiece resonance was reduced by sand or other damping methods; tool resonance, by internal damping; and chisel resonance, by constrained-layer treatment. Mufflers reduced air-exhaust noise, and an acoustically treated booth was effective in containing noise around the work area without increasing operator exposure.

Jan 1, 1977

By Leonard J. Prosser, Joseph Cervik, John H. Perry

The Bureau of Mines has developed several techniques for draining methane from coalbeds in advance of mining. Drilling long horizontal holes from an underground location is one such technique, which was successfully demonstrated in the Pittsburgh and Sunnyside Coalbeds. The same technique has now been applied in the Mary Lee Coalbed at Jim Walter Resources, Inc. 's No. 4 Mine, Brookwood, Ala. , where two holes were drilled horizontally--one to a depth of 1,010 feet (308 m) and the other to 540 feet (165 m). The 1,010-foot (3083) hole proved successful in degasifying a portion of the Mary Lee Coalbed. The hole drained methane for 1 year, during which time the initial gas flow of 200,000 ft3/d (5,663 m3/d) declined to 65,000 ft3/d (1,840 m3/d). Total gas production was 40 x lo6 ft3 (1.1 x lo6 m3 ). The gas was of commercial quality, with 98 pct methane and a heat rating of 990 Btu/ft (36.89 Mj/m3). The methane emissions from the faces of the mine section advancing into the degasified zone were reduced by 60 pct. The 540-foot (165-m) hole was terminated prematurely when it became impossible to maintain an open hole. Because of caving, very little gas was drained through this hole.

Jan 1, 1982

By J. E. Tiffany

"The new permissible blasting device, Cardox, utilizes as a blasting agent liquid carbon dioxide which is discharged.as a gas from a steel container or shell. The loaded shell is placed in a borehole, stemmed, and tamped in a manner similar to that employed with explosives, and is fired by electricity.The Bureau of Mines' approval for use of the device in coal mines was granted as Approval No. 1 under date of October 3, 1928; as the result of tests made under the conditions and requirements of Schedule 20. There have been three subsequent extensions whereby minor modifications in the original design were granted.The permissibility of the device is subject to the following conditions; (1) It shall be in all respects similar to the sample submitted for tests; (2) certain thicknesses of disc and. weights of heater ingredient and of carbon dioxide, all of which are set forth in Table 2 under the provisions governing permissibility, must be used: (3) the rear cap must always be in place after the shell has been charged, to prevent accidental firing; and (4) firing must be done by means of a permissible-type blasting unit.The permissibility of Cardox was established by gallery tests similar to those used in testing explosives for permissibility. In these tests the shell was discharged into gallery 1 without causing any ignition of gas and air or of gas, dust, and air mixtures there. The conditions of charging the shell, such as weight of the ingredients of the heater element, the carbon dioxide charge, and thicknesses of the disc, were varied according to the conditions under which it would be likely to be used in blasting. The tests made in gallery 1 are here described in detail, as are also the tests which have been made for determining the propulsive strength of the device and the quantities of poisonous gases given off when a shell is discharged."

Mar 1, 1929

By John C. Edwards

A computer code for laminar, steady-state, incompressible, two-dimensional flow developed by Gosman (2)3 was modified by the Bureau of Mines to calculate shock (minor) loss at the intersections of ventilation ducts. Turbulent flow was simulated using laminar flow equations and an appropriate wall shear stress. Results of the calculation showed good agreement with the experiment.

Jan 1, 1977

By R. V. Ramani, P. M. T. White, D. Sutton

4.1 Introduction Using methods outlined in previous sections of this report, programs were written and/or obtained to: i) select best combinations of "a" and "k" for up to 8 different value parameters, ii) calculate available and unavailable ore tonnages and other statistics, and iii) produce contour maps of various parameter characteristics and available tonnages on a line printer. All the above programs are written in Fortran IV for execu¬tion on IBM 360/370 computers. 4.2 Calculation of Coal Reserves The Ore Reserve program suite consists of the following sections: (a) UNIT 1: This unit is a subroutine called by Unit 2 to determine values for "a" and "k" from the given data. (b) UNIT 2: These programs calculate ore reserves and are composed of a main program and several sub¬routines. In the following, their functions are abbreviated: i) MAIN - calls subroutines, reads run parameter variables, reads borehole data and interpolates grid node values for the area of investigation

Jan 1, 1974

By R. F. Waters

The Bureau of Mines developed laboratory-scale processes to recover sodium phosphates and metal values from waste sludges generated by the phosphate treatment of automobile and appliance components. After treatment of the sludge with NaOH, followed by coke or hydrogen reduction and sintering, zinc and lead were recovered as fume; the sinter was separated by leaching into a metallic product, chiefly iron and nickel, and high-purity disodium or trisodium phosphate.

Jan 1, 1971

To reuse chromium, nickel, and molybdenum now lost in stainless and specialty steel-making wastes, and simultaneously to overcome the current environmental problem resulting from landfilling these wastes. Approach A variety of stainless and specialty steelmaking wastes are agglomerated and recharged into the plant's electric arc furnaces. How It Works Stainless and specialty steel-making wastes such as bag-house dust from the electric arc furnace, dust from the argon-oxygen decarburization unit, grinding swart, and mill scale are blended in proportion to the ratio in which they are generated. Next they are agglomerated on a pelletizer with an addition of a small amount of carbonaceous reducing agent, and air-dried in preparation for being recharged into the furnace. Some mixtures of wastes tested in the laboratory required the addition of binders and/or the use of ovens in lieu of air-drying to produce sufficient pellet strength. Although the optimal maximum particle size of wastes being pelletized is 35 mesh, somewhat larger particle sizes were satisfactorily pelletized during in-plant tests. The photograph shows a typical mixture of wastes and the pellets made from them.

Jan 1, 1981

By W. E. Lamont

The Bureau of Mines conducted flotation tests on a mixture of barite waste materials from Nevada in which essentially all of the barite values were finer than 20 micrometers. Flotation variables investigated in these tests were the effects of (1) sodium silicate as a pulp dispersant, (2) sodium hydroxide as a pH modifier, (3) increased amounts of sodium cetyl sulfate, (4) conditioning time and (5) solids content during conditioning. The optimum flotation conditions were achieved by adding 2.5 pounds of sodium silicate and 10 pounds of sodium cetyl sulfate per ton of feed and conditioning the pulp for 20 minutes at a 35-percent solids content. Using these conditions, a concentrate was produced that contained 94.7 percent BaS04, with an attendant recovery of 90.9 percent of the barite in the feed. In addition to the flotation tests, a selective barite flocculation process was developed to treat extremely fine barite. A barite concentrate containing 96.5 percent BaS04 with an attendant recovery of 82.1 percent of the barite was produced by selective flocculation. A process patent application has been filed based on this process.

Jan 1, 1982

By Thomas V. Falkie, R. Venkataramani

The purpose of this work was to Investigate the rate at which coal is delivered from the underground working face by gathering arm type loaders as employed on continuous mining machines, to identify the factors - geometrical , geological, mechanical, or procedural - which affect the delivery rate, and to develop quantitative rate-descriptive equations for the loading function. The mathematical techniques employed were factor analysis and multiple linear regression. It was determined that the coal-cutting function of the continuous mining machine is the factor that primarily Influences the loading function The geometrical factors -the dimensions of the work area In relation to the dimensions of the mining machine -were the factors of secondary influence. Fifty-five percent of the experimental variation in the loading function was explained in terms of the six most prominent Independent variables. It is expected that this work will be useful In operations-research studies as applied to underground coal mining, and with refinement will enable mine planners to select equipment based on the operating characteristics of the equipment and the mining conditions.

Sep 1, 1972

By E. A. Johnson

As part of its effort to reduce the environmental impact associated with mining and metallurgical operations, the Bureau of Mines used a modified form of the Environmental Protection Agency's Extraction Procedure toxicity test on copper reverberatory slags that contained low, medium, and high levels of the impurity elements As, Pb, Sb, Bi, and Zn. All tests resulted in extracts that did not exceed those limits published in the May 19, 1980, Federal Register; there-fore, these solid wastes were designated as nonhazardous for most landfill disposal situations. However, arsenic and lead levels disturbingly close to the allowable limits--and even higher levels of copper and zinc, for which there are no established limits--leached from the high-impurity-element granulated slags. These slags should be handled in such a way so as to minimize the possibility of water contamination. One baghouse dust was tested according to the EPA procedure and found to exceed the extract limits by a factor of 10. This solid waste may be considered hazardous.

Jan 1, 1982