Search Documents

Underground and strip mining (6,7) produce different hydrologic environments. Many underground mines are below the zone that is completely saturated with water and the mine openings may cause new and continuous contact between sulfurous material and water which flows from the saturated zone to the workings. Strip mines are usually above the zone of continuous saturation and contact between sulfurous material and water is generally restricted to periods of precipitation. A full appreciation of the problem of water pollution caused by drainage from deep mines requires a basic understanding of occurrences and movement of water in the ground and the modes of ground water entrance into mining areas.

Jan 1, 1970

By R. Sainath, Wils L. Cooley

Continuous monitoring of ground bed resistance is essential to insure a low-resistance path for fault currents, lightning strokes, and electrostatic discharges. This paper explains the salient features of the continuous ground bed monitor and its applications. The importance of a low-resistance path to ground is highlighted. Sample readings obtained with the ground bed monitor are included, and typical applications of this instrument are illustrated. This effort was supported by the U.S. Department of Interior's Bureau of Mines under USBM grant G0144138.

Jan 1, 1979

Maintain good blowing face ventilation while taking deeper cuts with a radio-remote, scrubber-equipped miner. Approach A six week in-mine study of face ventilation effectiveness was made by comparing the existing MSHA-approved blowing curtain setback distance of 25 ft with brattice set back distances of up to 50 ft. Effectiveness was determined by measuring methane levels at the face and in the immediate return. How It Works Blowing ventilation systems are commonly used in mines because the high velocity air stream created by these systems rapidly mixes with and dissipates methane generated during the cutting of coal. A drawback to blowing ventilation is that the work area is placed in return air and this may create dust compliance problems for the shuttle car and mining machine operator. To clean dust from the return a number of mining machine manufacturers supply dust scrubbers built into the machine. Dust-laden air is drawn into ducting at the front of the mining machine's boom and is ducted to a scrubbing unit located on the machine's main frame. The clean air from the scrubber is discharged as a high velocity jet toward the return, generally from the left fender of the mining machine. When taking cuts deeper than 20 to 25 ft with a scrubber-equipped machine, the machine's discharge is in by the mouth of the blowing curtain, creating a concern by mine workers that a loss of air to the face could result. However, Bureau of Mines research found that the push or throw of air toward the return by the scrubber discharge jet allows good face ventilation to be maintained with extended curtain setbacks.

Jan 1, 1984

To develop a system which will effectively detect and extinguish fires in underground fueling areas while also providing a warning for nearby miners. Approach A system involving optical fire sensors. automatically-released dry chemical and aqueous film-forming fluid (AFFF) fire suppressants, and automatic alarms was designed from off-the-shelf, state-of-the-art components, and was in-mine tested at two mines in the two typical underground fueling area situations: fuel transfer areas and fuel storage areas. How It Works As mines become more mechanized, the number of fire hazards increases since fueling areas are more abundant. Fire hazards are especially serious in deep mines, since escape time is longer. To help solve this growing problem, the Bureau of Mines, in cooperation with the Mine Safety and Health Administration (MSHA) and the National Fire Protection Association (NFPA), has developed and in-mine tested a cost-effective fueling area fire protection system. The system was designed to be rugged enough for reliable, long-term use, yet to utilize state-of-the-art, off-the-shelf components to maintain cost-effectiveness. The system consists of cross-zoned, ultraviolet flame sensors used for quick response to fire, and a dual-agent fire suppression subsystem. A dry chemical is used for fast fire -knockdown," and AFFF (or "light water") is used for long-term, fire-securing capability. The basic components of the system are shown in the schematic illustration.

Jan 1, 1982

By Albert E. Long

Diamond-bit performance and cost data accumulated in core-drilling sandstones reveal significant trends of economic interest. Large-size, AA-Grade drill bort suffered less diamond loss per foot drilled than any other size or grade of diamonds assessed. Detailed analyses of the factors that affect diamond-bit performances -diamond size, diamond quality, bit size, bit type, percentage of core recovered, and physical characteristics of bit matrices -are assessed in the tables, graphs, and discussion. INTRODUCTION Since 1945 the Bureau of Mines has been compiling detailed performance records on diamond bits used in core drilling throughout the United States and Alaska. Analytical reports covering bit performance in various rocks are issued as in-formation on a significant number of bits used in anyone type of rock is accumulated. The first three such reports analyzed bit performance in gneiss,2/ schist,3/ and lime-stone and dolomite.4/ This report evaluates diamond-bit performance in sandstone. Data obtained from 627 bits, which drilled 42,665 feet on 45 different projects, are presented. The geographical distribution of the projects is shown in figure 1.

Jan 1, 1958

By Fred Baldassare, Marcia Harris, Kenneth K. Eltschlager

Surface mine blasting was recently investigated as a potential source of high concentrations of stray gases found in nearby residences of western Pennsylvania. In one incident carbon monoxide was detected in a home and in the other, high concentrations of carbon dioxide were found in a home. Both carbon monoxide and carbon dioxide are by-products of blasting. However, other potential sources of these gases may also exist in a residential setting. In each case, gas chromatography (GC) and carbon isotopic analyses were used to define atmospheric concentrations inside the homes, and to determine the source of a stray gas. Molecular and isotopic analyses provide geochemical evidence as to the origin and source of the stray gas. This paper discusses elements of a stray gas investigation and the analyses necessary to identify the source of a stray gas.

By Howard E. Parkinson

A brief description is given of various Bureau of Mines research activities that have begun since July 1974 and are not being reported on by others at the Third West Virginia University (WVU) Conference on Coal Mine Electrotechnology. An essential feature of the various projects is that they are pragmatic. The projects are applied research and are carried out both by the Bureau in-house research group and by other research groups through contract research. Projects have been directed toward wired-type communications with a special effort to modify the wired systems so as to be more effectively used. The projects are in three groups: Pager phone systems, trolley line phone systems, and guided-wire wireless communications. Also, a brief sketch is given of research that is essential for further developments in mine communications. From the early results of these various projects, the Bureau has good reason to project that there will be improved performance of existing communication systems and that communications will be extended to other individuals working in areas that are excluded from present mine communication systems.

By Philip C. Tully

The Bureau of Mines, in a continuing effort to improve processes and methods of helium purification, has developed a differential distillation method for removing helium-3 from helium-4. Differential distillation at 4.2 to 1.6 K was used to reduce the helium-3 in helium-4 from about 200 to less than 1 part per billion. The results from four stills ranging in size from 1 to 25 liters are reported. The method has the potential to be adapted to commercial-scale separations.

Jan 1, 1975

By Joseph P. Flick, Kathleen M. Kowalski, Lynn L. Rethi, Roberta A. Calhoun

Many miners are involved in tasks at the mine site that are similar to those sub-tasks performed in general construction, maintenance and repair (CMR) type work activities. As a result, many of the injuries in the mining industry today can be traced to employees performing these CMR type work activities. Indeed, a recent analysis of a major aggregate company revealed that 65% of all injuries documented originated from performing such CMR activities. It is hypothesized that the number of injuries to miners performing construction, maintenance and repair (CMR) work activities on mine property may be reduced through improved training that focuses on better hazard recognition using the numerous visual and other cues that are available for evaluating workplace health and safety hazards. To this end, researchers at NIOSH’s Pittsburgh Research Laboratory have merged two proven methods of training miners to recognize hazards, stereoscopic (3-D) slides and the concept of degraded images, into this training program. Stereoscopic (3-D) slides have been shown in earlier NIOSH and U.S. Bureau of Mines research to be an effective training aid for improving the ability of miners to recognize various geologic and mining-induced irregularities that can cause groundfalls.3 They realistically portray the natural mine environment, and thus are an excellent training aid for teaching miners to recognize such visual cues. The degraded image concept, originally developed by the military and used for target detection training, describes scenes where the target is partially hidden by cloud cover, dust, rain, natural barriers, buildings, or other obstructions that can camouflage or confuse the target. Research had shown that flight observers who were trained with less than ideal (or degraded) pictures were more successful in subsequent identification of targets than those trained using ideal (or highlighted) pictures of targets. In order to investigate this concept for training miners to recognize hazards, NIOSH researchers developed a prototype hazard recognition training program using such mining scenes. A control program based on traditional highlighted mining scenes was also developed. Both programs were applied to subjects in a field experiment. Results indicated that miners trained with the degraded images did significantly better on a follow-up test of hazard recognition.4 This hazard recognition program teaches trainees to look for hazards in a more realistic manner than that of the control program. This specific training program for CMR activities involves using the degraded image concept and 3-D slides. The module is designed to educate workers on hazard identification techniques and safe work practices. It focuses on teaching miners techniques for recognizing visual (sight) cues, and then uses these cues to evaluate mining conditions. It should be stressed that other senses, such as sound can also play an important role in hazard detection.

Jan 1, 1999

Provide an improved, rugged, reliable, cost-effective automatic fire protection for mine haulage trucks. Approach Systems that automatically sense and extinguish fires on haulage trucks were designed, built, and in-mine tested. How It Works Temperature sensors mounted above the engine of the truck detect the heat from a fire while it is still small and controllable. A cab-mounted control panel warns the operator of the fire emergency and then automatically triggers the discharge of 60 pounds of multipurpose dry chemical extinguishing agent (from storage tanks through hoses and nozzles) into the engine compartment. If desired, the control panel can be field-adjusted by changing one resistor to delay the discharge for up to 60 seconds to allow time for the operator to stop the truck and shut down the engine. The system can be assembled with either pressurized storage tanks, or a combination of non-pressurized storage tanks plus separate pressure cartridges. This pressure source option is one of the improvements of this system over the earlier systems described in Technology News No. 11. Other improvements are a simplified control circuit and an improved sensor.

Jan 1, 1980

By Lloyd A. Morley, Robert Stefanko

1 Abaibanel, S , "Deflection of Confining Walls by Explosive Loads," Israel Jour. Technology, vol. 4, n. 1, Feb 1966. 2 Albertoni, S and others, "Numerical Computation Methods for Implosion Processes," EURATOM Proc. of the Conf. on Megagauss Magnetic Field Generation by Explosives and Related Experiments, Milan (Italy), July, 1966. 3 Alexander, S. J , and Hambly, E. C., "Design of Structures to Withstand Gaseous Explosions," Concrete, vol. 4, n 2, Feb. and March, 1970. 4 Anonymous (Belgium Institute of Extractive Industries), "Report for 1968 (covering approved equipment for Belgiums gassy coal mines)," (in French and Flemish), Amales des Mines de Belgigue, n. 6, June, 1969. 5. Anonymous (Ghent Univ., Belgium), "The Welding of Very Thick Steels. Margin of Uncertainty of the Robertson Test," EURATOM Contract 042-61-9-RDB, May 20, 1965. 6. Anonymous, "Inportance of the Nature and Size of Weld Defects with Regard to the Mechanical Strength of Pressure Vessels, (in Flemish), A. Sys. Rev. Soudure, vol. 27, n. 3, 1971. 7. Anonymous (Raentgen Technische Dienst N V., Rotterdam), "Non¬Destructive Welding," Quarterly Report No 13, EURAEC - 1342, March 30, 1965. 8. Anonymous (Staff, USBM Safety Research Center), "Research and Technologic Work on Explosives, Explosions, and Flames: Fiscal year 1969," USBM IC8492, 1970. 9. Anonymous, "Symposium on Flameproofing Intrinsic Safety and Other Safeguards in Electrical Instrument Practice, April 27, 1962," IEEE Conf. Report Ser. 3, 1963. 10. Anonymous, "Unfired Pressure Vessels," ASME Pressure Vessel Code, Sec. 8, 1965. 11. Anonymous, "Unusual Pressure Relief Devices," Industrial and Engineering Chemistry, vol 54, n. 1, Jan., 1962. 12. Archer, G. L., "Design to Avoid Brittle Fracture in Welded Structures," Paper No. 4, Improving Welded Prod Design, vol. 1, Welding Inst., Cambridge, England, 1971. 13. Bailey, F. C., "Buckling and Failure Strength of Plating Panels Loaded in Shear," Final Report NASA Contract NObs-72290, Lessels and Assoc., Inc., Waltham, Mass., Sept. 20, 1963.

Jan 1, 1974

By G. B. Atkinson

To develop technology to help assure an ample domestic supply of zinc, the Bureau of Mines is investigating an aqueous chlorine-oxygen leaching process for treating complex sulfide concentrates. This report discusses the purification of aqueous C12-02 leaching solutions by utilizing zinc cementation to remove Cd, Co, Cu, Ni, and Pb. Additional processing of the purified solution is necessary to produce ZnC12 crystals suitable for molten-salt zinc electrowinning cells. The effects of solution temperature, reaction time, zinc dust concentration, ZnCl2 concentration, and degree of agitation on the removal of impurities were investigated for both simulated and actual leaching solutions. Zinc dust addition to a leaching solution at 30° C decreased the Cd, Cu, Ni, and Pb concentrations to acceptable levels of less than 3 mg/1 each. By increasing the solution temperature to 75° C, the cobalt content was decreased to less than 5 mg/l, an acceptable level for producing electrolytic cell-grade ZnC12. Impurity removal rates from ZnCl2 solutions are Pb>Cu=Cd>Ni>>Co. An increase in the solution temperature increases the rate of removal for these metal impurities.

Jan 1, 1982

Increase the recycling of critical and strategic materials by simplifying the indentification and segregation of scrap. Background Because the United States is dl-most totally dependent on imports of such critical metals as chromium, cobalt and nickel, Bureau of Mines research has been directed towards conserving these metals by increasing the recycling of the complex scrap materials that contain them. Experienced scrap sorters, using the traditional techniques of object recognition, spark tests, chemical spot tests, color, apparent density, and magnetic properties, can adequately sort a wide variety of alloy groups. However, the complex nature of new materials entering the scrap market has made sorting both more difficult and more important. Some new alloys contain so many components that separation by discrete alloys becomes a prerequisite for effective recycling. The Bureau has completed Investigations on two methods for rapidly sorting complex scrap mixtures. One method uses a combination of two low-cost instruments. The other uses a single sorting instrument. Both approaches are reported.

Jan 1, 1986

By J. E. Emmerling

The Federal Bureau of Mines investigated dust suppression obtained with three different water-spray nozzle systems during underground continuous coal mining at the face. The nozzles were the "regular" nozzle normally used by the mine, and high-efficiency and low-efficiency nozzles selected on the basis of an airborne capture theory of respirable dust by spray drops. The high-efficiency nozzle used one-third less water than the others throughout the testing. Results depended on the type of cutting operation at the face. The sump-downshear operation appeared to involve a significant amount of capture of airborne respirable dust. The same amount of dust was measured when using the high-efficiency and regular nozzles. The dust levels when using the high-efficiency nozzle were about 20 pct less than those measured when using the low-efficiency nozzle. The sump-upshear operation seemed to involve a predominance of other aspects of dust suppression, such as impaction of spray drops onto the face. Compared with the downshear operation, there was a significant reduction in dust levels for a total face operation when using the regular nozzle; dust levels when using the regular nozzle were about 15 pct lower than those measured when using the high-efficiency nozzle.

Jan 1, 1975

By J. F. Barkley

"In the course of the Government's Fuel Economy Survey of its own power plants, studies and tests have been made of various oil-burning equipments under power-plant boilers. There are now many types of burners being offered in the relatively limited field of power-plant use. The majority of the types used may be grouped into two general classes- those using steam to effect the atomizing of the oil, and those using mechanical means.Burners using steam have had the most prominence in this field for a long period. The mechanical atomizing type of burner successfully applied on shipboard, however, pointed to a possible betterment in land work. The vision presented itself of a burner that would need no steam for atomizing that would permit of air inlets or registers compactly arranged as a part of the entire burner, and that would only require the natural stack draft usually available in land boiler furnaces. Hence, rather recently there has been much development along this line, resulting in various types of burners.In Table 1 are grouped test items chosen from many tests showing representative analyses of the products of combustion obtained with various burners installed in various types of furnaces. In all these tests the burners were handled by experts and represent practically the best attainable for that particular arrangement. The boiler efficiencies ranged from 70% to 80%. It will be noted that the burners using steam for atomizing were able to secure slightly better 002 and less 02 without the presence of CO."

Feb 1, 1926

By C. P. Hood

"The amount of ash in anthracite coal interests every buyer, and occasionally produces caustic comment, but there is a lack of authentic figures that will take the subject out of the realm of opinion and agitated fancy and. give a true picture of the quality of coal actually delivered. What per cent ash is to be expected when the coal is good, and when have we a right to make serious complaint?During the past summer the Bureau of Mines took 127 samples of 1000 pounds each, representing nearly 30,000 tons of anthracite is dealers' yards in seventeen cities in the State of Massachusetts. There were three objects in view, to discover the average and the variation in amount of ash in anthracite in some easily described area; to demonstrate standard sampling methods, and to learn something about the feasibility of itinerant coal sampling. Massachusetts was selected because its principal cities could be visited in a single season. There also appeared need for demonstration of standard sampling of coal, since a coal quality law had been passed in the State, to be administered by those unfamiliar with coal sampling."

Feb 1, 1924

To enhance safety and efficiency when moving large mining equipment under energized trolley lines, and to assist in compliance with Section 75.1003.2, 30 CFR. Approach A system was designed, using established technology, that permits a remotely located circuit breaker to be controlled from the cab of a mine locomotive moving large mining equipment under energized trolley lines. This control consists of setting the desired trip current, automatic or manual tripping, resetting, and voice communications between the locomotive and a remote Circuit breaker location. How It Works According to 75.1003.2, 30 CFR, whenever a piece of off-track equipment (such as a longwall chock or a continuous miner) is moved by rail under energized trolley or feeder lines, power for the locomotive that is moving the equipment must come from only one' circuit breaker. This circuit breaker must be adjusted to permit no more than one-half its rated short-circuit current to flow. The intent is to lessen the danger if an accident should occur, and if the equipment contacts the trolley line. Even so, the danger is great. This half setting can still represent many hundreds or even thousands of amperes, enough to endanger personnel, the equipment, or the mine. The Remote Control System reduces this danger substantially by giving the personnel associated with the move total control over the associated circuit breaker. The system as designed, is intended to be used with portable circuit breakers that are pulled on a small flat car by a mine jeep, and either precede or follow the equipment, depending on the direction of the power. This portable circuit breaker is equipped with a commercially available solid state overcurrent relay and associated shunt. This circuit breaker is connected via heavy duty clamps around an open trolley line tie breaker such that the current through the shunt is also the current in the trolley line. A receiver, interfaced with the overcurrent relay and shunt, completes the remote system.

Jan 1, 1981

By N. E. Hanna

To be authorized for use in coal mines, explosives and blasting devices must pass certain safety tests prescribed in schedule 1F,3/ on the basis of extensive practical and theoretical research by the Explosives Testing Station of the Federal Bureau of Mines. An explosive or blasting device that passes these tests is placed on the active permissible list. As this list is constantly revised, it has been the practice of the Bureau of Mines periodically to publish the names of explosives and blasting devices that have been added to the active list, as well as those that have been transferred to the inactive list; changes in brand names also are reported. This circular covers all permissibles including additions, transfers, and changes made between December 31, 1945,4/ and December 31, 1951.

Jan 1, 1952

By L. B. Pankratz

The heat content above 298.15° K was determined for crystalline vanadium silicide of the composition V3Si. This substance has a minor thermal anomaly (probably a heat-capacity maximum) near 560° K; the extra heat absorption is about 50 cal/mole. The original heat-content data are presented, and smooth values of the heat content and the corresponding entropy increments are listed for the temperature range from 298.15° to 1,500° K. Equations representing the heat- content values and derived heat capacities are also included.

Jan 1, 1963

By William G. Gruzenaky

The separation of yttrium and the individual rare-earth elements (lanthanons) from mixtures in which they occur has been a difficult problem through-out the years. Because of the increased interest in the various uses of these metals, the economy of their production may become of great importance. Studies relative to this problem, undertaken at the Federal Bureau of Mines Albany Metallurgy Research Center, resulted in the development of a solvent extraction method by which yttrium can be separated from the rare-earth metals. A separation factor of 10.93 was obtained between yttrium and cerium from a single-stage extraction, and a factor of 1.78 was obtained between yttrium and erbium from a multistage system. The valuable metals were extracted from euxenite by caustic soda fusion or by chlorination, and several separation methods were investigated. Partial separation of the yttrium and rare-earth element fraction was made by chemical methods and by solvent extraction. Thermal decomposition of aqueous rare-earth nitrates or selective ignition of yttrium and rare-earth oxalates yielded a fraction enriched in cerium. A fraction enriched in the light rare-earth elements resulted from a double sulfate precipitation, whereas a potassium ferrocyanide pr cipitation yielded a fraction enriched in yttrium. Precipitation with dimethyl phosphate yielded a fraction enriched in yttrium and heavy rare-earth elements. Enriched fractions were obtained with several solvent extraction systems. A system consisting of rare-earth nitrates, nitric acid, and tri-n-butylamine-3 methyl-2-butanone favored the separation of yttrium from the heavy as well as from the light rare-earth elements.

Jan 1, 1961