Search Documents

By C. W. Owings, J. J. Forbes

"INTRODUCTION The recent coal-dust explosions in Illinois and Indiana have again brought forcibly to the attention of mining men the fact that mines which liberate little or no methane can have widespread explosions, if dry and dusty conditions exist and if adequate measures are not taken to control the dust hazard by rock dust¬ing or use of water.Even though rock dust has been used more or less extensively for more than 20 years as a means of limiting or preventing coal-mine explosions, many mine operators have requested information on rock dusting and means of allaying coal dust at its source. The purpose of this circular is to summarize available information on these two methods.COAL MINES TO BE ROCK-DUSTEDAll nonanthracite coal mines must be rock-dusted, except those mines or locations in a mine that are too wet or too high in incombustible content to propagate an explosion.Coal dust that contains 20 percent or more moisture may prevent ignition or propagation of an explosion. Such dust can be molded in the hands, and under such condition the roadway would be considered muddy. Mine dust that is only damp is not wet enough to prevent propagation of an explosion. Beads of water standing on accumulations of dust are not indications that the dust is wet. Only those mines or locations in a mine in which the coal dust can be molded in the hand need not be rock-dusted."

Jun 1, 1947

Establish a procedure for reliably determining cation exchange parameters at an in situ mining site. The Problem Predicting the movement rates of pollutants from waste disposal sites requires reliable measurements of cation exchange parameters since cation exchange can retard pollutant movement. Reliable measurements of these parameters are also required for predicting the length of time needed to restore groundwater quality after in situ mining. Cation exchange is otten the controlling mechanism for the replacement of leach solution cations by the cations in the returning ground-water. Unfortunately, laboratory measurements using core samples are of minimal reliability. The uneven clay distribution at most sites produces a high variability in laboratory results. In addition the flow pattern in the laboratory tests is different from that in the field. Approach Bureau of Mines research has developed a field-test procedure that is quick and yields reliable and representative data. A corresponding data analysis procedure was also established in order to verify the' applicability of the computer simulation model of cation exchange used in the analysis, and of the general analysis procedure, with actual field data.

Jan 1, 1986

Reduce injuries caused by slips and falls from large haulage vehicles. Approach Replace the flexible-cable or chain-type lower ladder steps, with steps that extend closer to the ground and do not sway when stepped on. Modify dimensions of entire ladder to new industry recommendations. How It Works New lower ladder steps are supported by side pieces made of pretensioned, solid-wound, coil springs fabricated from high strength steel. Unlike conventional crash-resistant steps, which flex or swing freely when stepped on, the spring supported steps can maintain the same inclination as the fixed upper portion of the ladder while supporting an average-weight operator. The steps are also highly resistant to collision damage because they yield on impact if rammed into obstructions such as rocks or berms. See photograph.

Jan 1, 1980

By H. O. Poppleton

This Bureau of Mines study was made to investigate a possible method for selectively removing the Si02 component of silicate minerals and ores. Of specific interest were aluminum ores and zircon. Methods are described for removing Si02 from these ores as volatile silicon sulfides by treating the ore with sulfur and carbon; with sulfur, carbon, and a reducing gas; or with sulfur compounds and carbon. Comparative results are also given for the desilication of some of the ores with carbon alone to form volatile silicon monoxide. The silica component can be removed partially from bauxites at temperatures above the sublimation temperature of SiS (940° C) by treatment with carbon, sulfur, and methane; however, it is more difficult to remove the silicon from kyanite, manganese silicate, red muds from aluminum processing, kaolinite, lateritic nickel ores, and zircon. Complete desilication requires temperatures ranging from 1,100° C for bauxite to 1,450° C for zircon. Although the high temperatures required and the undesirable metal sulfides produced eliminate practical application of this method using present technology, the Bureau is reporting this data so that they will be available to future investigators.

Jan 1, 1974

By D. H. Chambers

The Bureau of Mines developed a process for producing high-purity zinc and tin by electrorefining from liquid amalgams. Commercial grade metals were dissolved in mercury to produce saturated amalgams at room temperature. Amalgams were also prepared by electrolytic transfer from soluble anodes of the metals to a mercury cathode. Amalgams formed by both methods were used as anodes in electrorefining cells to produce high-purity cathodes. Metal impurities, excluding mercury, were at levels of less than 5 ppm in zinc and 9 ppm in tin. Mercury content was about 2 to 10 ppm in zinc products, and this was effectively removed by heating the cathodes in a vacuum. Mercury was excluded from tin cathodes by pumping the tin electrolyte through tin turnings and controlling the cell temperature.

Jan 1, 1969

Legislation and Government Programs.-On February 4, 1977, the Occupational Safety and Health Administration (OSHA) issued its final environmental impact statement on the occupational use of inorganic arsenic.2 The statement examined the ramifications of the original proposed standard published in the Draft Environmental Impact Statement (DEIS).3 The DEIS proposed to limit the exposure of employees to no more than 4 micrograms of arsenic per cubic meter of air as determined on an 8-hour-time-weighted average basis; or a ceiling limit of 10 micrograms of arsenic per cubic meter of air based on a 15 minute sampling period. The purpose of the proposed regulation is to reduce the risk of smelter workers developing lung and skin cancer as a result of exposure. A comprehensive study compiled by the Committee on Medical and Biologic Effects of Environmental Pollutants concluded that "there is strong epidemiologic evidence that inorganic arsenic is a skin and lung carcinogen in man."' In April 1977, the Environmental Protection Agency (EPA) served notice to ASARCO Incorporated that its Tacoma copper smelter and associated arsenic-producing facilities were in violation of State laws which limit sulfur dioxide and particulate matter emissions. This notice followed the Washington State Pollution Control Hearing Board overturning a prior ruling by the Puget Sound Air Pollution Control Agency (PSAPCA) which had permitted a 5-year variance from the State of Washington air quality standards. In December 1977, ASARCO appealed in court the decision of the Hearing Board.

Jan 1, 1980

By James E. Hill

TECHNOLOGY is best nurtured by a sympathetic climate that is a composite of many factors. Necessity is a highly motivating factor as illustrated by the abnormal surge of technologic development curing wartime. Other factors include appropriate timing, economic pressures, available personnel, and in some instances, legislative action. Problems of recent concern to mining technology have been the quality and quantity of available technical personnel and the possibilities of restrictive legislation. The quality and quantity of technically trained personnel may be inadequate to meet the rapidly increasing complexity of modern technology coupled with the growing demand for qualified personnel. The question of appropriate training was a subject for debate.2 The curriculum and methods of teaching have changed. Questions have been raised on the relationship of scientist and engineer, interdisciplinary versus specialized curriculum, undergraduate versus graduate training, and the place of the smaller schools versus the large university-research complexes that have developed at some universities. Various aspects of the subject of engineering education for the mining industry were discussed at the meeting on Mining and Mineral Engineering Manpower at the Michigan College of Mining and Technology, November 18-19, 1963. Meanwhile, the trend toward interdisciplinary training gathers momentum as illustrated by the establishment of the School of Engineering Science at Johns Hopkins, the Schools of Engineering and Applied Science at Columbia, Princeton, and Yale, the Division of Engineering and Applied Physics at Harvard and, more recently, the School of Engineering Science at Florida State University which cuts across the conventional areas of civil, mechanical, electrical, and chemical engineering.

Jan 1, 1964

To test the feasibility of hydraulic borehole mining for the recovery of phosphate ore from the deep, water-saturated deposits of northeastern Florida. Approach Phosphate ore is remotely extracted through a Bureau of Mines-developed hydraulic borehole mining system. Hydraulic borehole mining can remove underground ore deposits that cannot be economically mined by the usual open pit or underground methods. It is environmentally compatible, causing none of the surface disruption or ground water pollution usually associated with other methods of mining. Selectivity of the borehole mining system also allows economical recovery of small or discontinuous ore deposits while minimizing the removal of host rock. The hydraulic borehole mining system has been used successfully in the past to mine uranium ore and oil sands. (For examples of these and other applications of borehole mining see T Technology News Nos. 97, 95, 63, 56, and 48) How it Works A 16-inch-diameter borehole is drilled from the surface down into the buried mineral deposit, and the mining tool is installed. The borehole mining tool consists of a 12-inch-diameter pipe string and accessories capped with a three-passage swivel, and ending with a mining section. The mining section has four slurry inlets and an eductor located near the bottom of the section and a single cutting nozzle located near the top. The tool generates a high velocity water jet that erodes and slurrifies the ore. The slurry is drawn through the inlet into the eductor which lifts it to the surface where it is deposited into a slurry discharge sump. All the support equipment is located and operated on the surface; only the mining tool portion of the system is underground during the recovery operation.

Jan 1, 1983

The National Institute for Occupational Safety and Health (NIOSH) National Personal Protec-tive Technology Laboratory (NPPTL) and the Mine Safety and Health Administration (MSHA) conduct a Long Term Field Evaluation (LTFE) program to evaluate deployed self-contained self-rescuers (SCSRs). The objective of the program is to evaluate how well SCSRs endure the under-ground coal mining environment with regard to both physical damage and aging when they are deployed in accordance with Federal regulations (30 CFR 75.1714). This report presents ?ndings of the combined eighth and ninth phases of the LTFE. For these phases, over four hundred SCSRs were evaluated. The units tested include the CSE SR-100, Draeger Oxy K-Plus, MSA Life-saver 60, and the OCENCO EBA 6.5. The OCENCO M-20 was evaluated only in Phase 9. Testing was per-formed between December 2000 and April 2004. Results of the evaluation indicate that all SCSRs experience some performance degradation due to the mining environment. Observed degrada-tion varies from elevated levels of carbon dioxide, high breathing resistance, and reduced capacity. Mechanical degradation to the SCSR components included breathing hoses, chemical beds, outer cases and seals. The LTFE tests discussed in this report are different from tests performed for SCSR certi?cation to the requirements of 42 Code of Federal Regulations, Part 84 (42 CFR, Part 84). LTFE tests reported here are conducted to an end point, oxygen depletion, to enable comparison of the duration of new and deployed SCSRs. The method for obtaining deployed SCSRs for this evalua-tion was not a random selection from the deployed population of SCSRs. Although the results of these tests are useful for observing performance of the tested SCSRs, they are not representative of all deployed SCSRs. A new evaluation protocol, with revised sampling strategies, test methods, and reporting procedures, is currently being designed to enhance the generalizability of the results. This program will be implemented following completion of Phase 10 of the current LTFE protocol.

Jan 10, 2006

To suppress the natural bacterial action in acid mine drainage (AMD), the major contributor to acid formation. Approach Recycle partially-treated affluent back to the source of AMD within a mine, or to the coal or coal-waste stockpile. This effectively eliminates any further biologically-promoted AMD by inhibiting catalyzed weathering or oxidation by acid-forming bacteria. How it Works AMO-type effluents can be largely reduced by "recycling" the acidic outflow back to the source of AMD within a mine or to the Input side of a waste pile to percolate through the reactive pyrite and bacteria mixture. The bacteria in the cell thrive on the oxidation of ferrous to ferric iron through the electron transfer, Fe2 +[=]Fe3 + + e. Its reaction product [s, therefore, essentially ferric iron. While small quantities of Fe3 + will not interfere with the exponential multiplication of the bacteria

Jan 1, 1982

The following methods should be used to protect miners from the adverse health effects of exposure to respirable coal mine dust and respirable crystalline silica: ? Informing workers about hazards ? Establishing written emergency procedures ? Using engineering controls, work practices, and personal protective equipment (including respiratory protection when dust control equipment is being installed, maintained, or repaired) ? Monitoring exposures ? Conducting medical screening and surveillance ? Encouraging smoking cessation ? Maintaining medical records

Jan 1, 1997

By F. P. Haver

A procedure is described for recovering both lead and sulfur from galena flotation concentrate, comprising the following steps: (1) Aqueous oxidation of the concentrate, using ferric sulfate to convert lead sulfide to sulfate and to give elemental sulfur; (2) regeneration of the ferric sulfate by electrolysis in a diaphragm cell; (3) treatment of the leach residue with ammonium carbonate solution to change the lead to an acid-soluble form and to produce ammonium sulfate as a byproduct; (4) solution of the lead carbonate in hydro-fluosilicic acid followed by electrolysis to recover the lead as metal and regenerate the acid; and (5) extraction of the elemental sulfur from the final residue with an organic solvent. About 90 percent of the lead can be recovered by the above method as 99.9-percent-pure metal, together with two-thirds of the sulfur--half in the elemental form and half as ammonium sulfate.

Jan 1, 1970

Design a model health and safety program which, when implemented, can improve mine safety by reducing occupational injuries and accidents. Approach The Bureau of Mines developed a model program which identifies the elements essential to the effectiveness of health and safety programs designed for mining operations, and is readily adaptable to all types of sizes of mines. The model program primarily provides training on loss control and accident investigation and technical assistance with health and safety problems. In order to assess the effectiveness of the program, it was tested at both a coal and gold mining operation. Monthly statistics were generated to reflect the number of occupational injuries and accidents, and the severity of injuries (as measured by the number of work days lost during recovery). Observations were made of employees performing a large number of randomly selected jobs in order to estimate. the proportion of the workforce that was working in the presence of one or more of three types of safety deficiencies: Type A-individual job performance deficiencies which could be corrected by the employee alone I e.g., an employee is seen not wearing a seatbelt.

Jan 1, 1986

Lower noise exposure levels for operators and cleanup personnel working in portable nonmetallic mineral crushing and screening plants.

Jan 1, 1983

Determine what diameter piping is necessary to obtain sufficient water flow to spray nozzles used for dust suppression. Approach A simplified, diagrammatic method of calculating the flow of water through a proposed system consisting of a supply line and two banks of spray nuzzles is outlined. How It Works The pressure versus flowrate of the supply at the tapping point must be known or measured. The supply curve of typical city water at a 1 ¼ -inch pipe outlet is shown by the lowest curve in Figure 1. A supply curve for a typical pump fed from an open sump is shown by the middle curve. The combination of these, the supply curve of a pump fed by the city water supply is shown by adding the lower two curves to get the upper curve. A pump supply curve showing flowrate versus pressure is usually supplied by the manufacturer. The water supply line flow curve can be determined by measuring the time required to fill a 55 gallon barrel at various valve settings to determine flow, and by measuring corresponding pressures at the valve with a gauge.

Jan 1, 1979

By P. A. Bloom

Arsenic-containing flue dusts are currently being stockpiled by several nonferrous smelters in the United States. These stockpiles are a source of environmental concern since the dusts can be transported by wind and contain water-soluble arsenic. The stockpiles also represent an alternate source of metals. To provide a quality environment, the Bureau of Mines investigated a process to make environmentally acceptable the discard of arsenic obtained from the treatment of arsenical flue dust. The process includes (1) leaching arsenic from a lead smelter copper dross flue dust, (2) fixing arsenic as an insoluble compound, and (3) recovering other metal values. Overall results of acid-leaching tests on lead-smelter flue dusts showed that H2S04 dissolved 80 to 90 percent of the As, Zn, and Cd, and up to 86 percent of the In. Pb, Ag, and Au remain in the residue, which can be recycled to the smelter. Indium was recovered from the strong acid leach solution by solvent extraction; arsenic was fixed in a stable form by precipitation with Fe2(S04)3 and CaO or CaC03.

Jan 1, 1982

Provide a method of detecting and locating miners trapped underground following a mine disaster. Approach Develop a surface deployed system which senses the vibrations caused by a trapped miner pounding on the roof of the mine and effectively determines the miner's location. How It Works If trapped underground, a miner would strike the roof of the mine with any implement at his disposal. This pounding causes vibrations in the ground which are transmitted to the surface where they are sensed by receiving transducers called geophones. Multiple geophones are positioned together for noise cancellation purposes in a form called a subarray. Seven

Jan 1, 1981

Reduce methane levels around the shearer machine during longwall mining by directing more of the available airflow along the face and over the shearer body. Approach To address the entire mining cycle, two techniques were combined to dilute and clear the methane liberated from the face by the shearer during cutting. The first is the modified shearer clearer system, which is used during the entire face pass. This is combined with the walkway curtain which is used only during the headgate cutout. How It Works Methane ignitions are one of the most potentially serious hazards facing longwall mine operators. The high rate of coal extraction on longwall sections can liberate a significant quantity of methane during a pass. The modified shearer clearer is used to dilute methane concentrations along the entire face for both cut directions. The shearer clearer system, originally designed as a dust control technique, uses a series of water sprays located on the shearer body to direct more airflow along the face and over the shearer. (See Technology News issues, #112, #118, and #221). The only change from the original shearer clearer design is the addition of three sprays to the return-side splitter-arm/ shearer interface. The additional sprays help to ventilate the area behind the shearer body.

Jan 1, 1985

By R. D. Leitch, W. P. Yant

"In the course of another investigation4 during 1926 and 1927, samples of water collected from a few abandoned coal mines indicated that their drainage was usually lower in acidity than water from active mines in the same locality. In order to determine whether this condition might have a bearing on the advisability of sealing abandoned mines, a number of such mines were visited, samples of drainage were collected, and as much information- as possible was obtained from officials of the mining companies and older residents of the district. The results of this work are the basis of the present report.The authors are indebted to E. W. Robertson, F. F. Spowart, J. H. Nagle, and W. D. Adams of the Northwest Mining & Exchange Co.; E. M. Fasset, Fred Lane, Wm. Humphreys, and Dr. T. A. Hutchison of Brockway, Pa.; C. W. .Faulk of the Shawmut Mining Co.; James Hau of Kersey, Pa., and to others for information received; and to Dr. R. R. Sayers of the Bureau of Mines, under whose direction the work was conducted.The Lower Kittanning is the most important bed in the locality studied. A great many of the abandoned mines examined are in this bed, and nearly all of the present active ones are. The Upper Freeport bed is also mined to some extent, and a number of the abandoned mines formerly worked this bed. As only three active mines are now (1927) working the Upper Freeport, the comparison of acidities is necessarily limited. Of these three, one had been idle since 1922 until shortly before it was sampled.The location of most of the mines was already known from previous work, but some of them had to be located by following up streams known to contain acid waters. A sample of the- outflow was collected in self-sealing bottles known as ""citrate bottles"" for the determination of dissolved oxygen by the Winkler method.5 Another sample was taken for the determination of acidity according to standard methods of water analysis.6 Ferrous iron was determined at the mine or very soon after taking the sample by titrating with a standard solution of potassium permanganate in acid solution. The hydrogen-ion value was determined by a standard double-wedge comparator.7From the total acidity values in each sample, which are the most important values, the total iron was calculated on the assumption that acidity as sulphuric acid was due to dissolved ferrous sulphate. This assumption is commonly made for mine waters, but is inaccurate to the extent that free acid is already present, and some of the iron is present as ferric, rather than ferrous, sulphate. The amount of ferrous sulphate may be a rough measure of the extent to which oxygen is lacking within the mine. The permanganate titrations just mentioned showed what part of this total iron was in combination as ferrous sulphate, and the difference .was assumed to be that in combination as ferric sulphate, after correcting for the amount of free acid already formed as shown by the titration values."

Oct 1, 1928

By B. J. Scheiner

Carbonaceous gold-bearing ores of the type that occur in north-central and northeastern Nevada were investigated by the Bureau of Mines as part of its Heavy Metals Program. Specific objectives were to identify the carbon and organic compounds that prevent adequate gold recovery from the ore by cyanidation and to develop an economical process that would overcome the detrimental effect of the carbonaceous constituents. Activated carbon and long-chain organic compounds containing sulfur and nitrogen were found in the ore. Part of the material consisted of stable gold organic complexes. A mild oxidation technique that allowed gold extraction as high as 96 percent by subsequent cyanidation was developed. A variety of oxidants was shown to be effective in improving gold recovery, including chlorine and sodium hypochlorite (NaOC1). An electrolytic oxidation process was developed that was particularly advantageous from an economic and effectiveness standpoint.

Jan 1, 1971