Search Documents

By Phyllip Worley, Frank E. Chase, Christopher Mark

The Harris No. 1 Mine, located in Boone County, WV, has been longwalling the Eagle Coalbed for over 30 years. Harris has experienced numerous interactions associated with the extensive room-and-pillar and longwall mining operations which have been conducted in the overlying No. 2 Gas Coalbed. The problems have included roof falls, excessive rib sloughage, and gateroad and bleeder entry closure. A detailed evaluation of the multiple seam experiences at Harris No. 1 Mine was conducted as part of the National Institute for Occupational Safety and Health (NIOSH) nation-wide multiple seam mining case history data base. One observation from the Harris gateroad case histories was that smaller, critically loaded, upper seam pillars seemed to cause more severe ground conditions than did wider pillars. The LaModel program was used to investigate this supposition, and the results confirmed that “critical” sized pillars do transmit the highest amounts of stress to adjacent seams. In addition, the data suggest that the probability of a major multiple seam mining interaction increases when the depth of cover is 1,000 ft or greater and when the Eagle seam pillars have a Analysis of Longwall Pillar stability factor less than 1.50.

By S. C. Tadolini, T. M. Barczark

Mines in the western United States have had limited choices for standing support. Wood cribs were often too soft and unstable. The introduction of the Can support in the earl v 1990s provided an effective alternative, (lilt/ it remains the dominant form of tail¬gate support. Water-filled prestressing cells are now used to cap the Can and preload it to provide an active roof load. The Cluster Prop, consisting of three timber wedge props bundled to¬gether; provides more capacity than (m equivalent sized Call support and improves transport efficiency. However the Cluster Prop is less stable and does not maintain a consistent load throughout its loading profile. Pumpable roof supports are another alternative support, but the \' have not been proven in high deformation en¬vironments. This paper compares the performance characteristics o f these various support systems.

By Kenneth C. Stewart

Eight brands (three samples of each kind) of commercially available audio-dosimeters were performance-tested. Each unit was placed in an anechoic chamber and subjected to various acoustic signals to measure its A-weighting response and overall integration accuracy. All units met the A-weighting tolerance for type II sould level meters, and six brands were within the Bureau I s overall accuracy requirements of ±2 dbA referred to input.

Jan 1, 1974

By George S. Koch

Several methods of calculating ore grades by diamond-drill sampling in the Homestake mine, Lead, S. Dak., have been evaluated by statistical analyses of assay data. The natural distribution of gold particles, partly masked through sampling and assaying procedures, is probably lognormal. As a consequence of the gold particles being clustered rather than randomly distributed within the ore bodies, (1) more mine samples are needed to obtain a specified precision of mean grade than the number predicted by the standard-error-of-the-mean law; (2) the variance of gold values is not inversely proportional to sample volume, and, therefore, small-diameter drill core yields samples nearly as good as larger diameter core; and (3) sampling at 5-foot intervals provides nearly as good results as sampling at shorter intervals.

Jan 1, 1971

By Paul E. Loustaunau, Devah Galloway, Catherine Wetherby

This report describes a project in which Development of a Supervisory and Management Training Program for the Underground Coal Mining Industry was developed and evaluated. The project was carried out in two phases. The first phase was a research effort to develop specifications for the program. The second phase was a development and evaluation effort. In the second phase, training programs for first-line supervisors (section foremen) and for middle managers (mine/shift foremen and mine superintendents) were prepared in accordance with the specifications and evaluated by members of the industry. This report describes the project and presents the conclusions drawn there from.

Jan 5, 1983

By J. C. Nigro

Hematite-to-magnetite reduction kinetics were investigated mainly in CO-CO2 atmospheres at temperatures ranging from 500° to 1,000° C. Reduction rates were measured with a thermobalance, which recorded the weight loss as the specimen was reduced. Reduction data on both synthetic and natural hematite spheres showed good linearity of ro [1-(1-R)1/3] with time, t, up to over 85 pct conversion to magnetite; the rate coefficient (k[L], cm/min) obtained from the linear portion of the plot was used to characterize the penetration rate of the hematite-magnetite interface. Gas composition, porosity, and silica content were major factors affecting the rate. Temperature dependency of the reaction rate was small, yielding a mean activation energy of about 3 kcal/mole. Silica additions increased the reaction rate, probably through an increase in the effective surface area and diffusion; however, above 900° C, silica can react to form fayalite. Experimental data showed that the linear thickening rate of the magnetite layer, normally evidence of a chemically controlled reaction, can also be indicative of a reaction controlled by both mass transfer and diffusion. Evidence from this study indicates that the dominant rate-controlling factor in the reduction of hematite to magnetite at high temperatures is transport in the gas phase.

Jan 1, 1973

Part Two of this report is based upon six working memoranda prepared during the first half of 1972 at an early stage in our work for the Bureau of Mines. This work presents preliminary performance estimates of baseband voice and narrowband through-the-earth electromagnetic communications systems of principal interest to the Bureau for operational/ emergency mine communications applications. The calculations were prepared to obtain early indications of the feasibility and governing parameters of such communications systems. They are based on limited, but pertinent, coal mine electromagnetic noise data acquired to-date by Bureau of Mines contractors; on theoretical signal-attenuation characteristics for two transmitter antenna types of present interest to the Bureau and on semi-empirical models which describe the intelligibility of voice communications as a function of the frequency variations of the signal-to-noise ratio across the voiceband. This work examines the cases of baseband voice and narrowband communications for uplink and downlink transmissions, for frequencies up to 3kHz. Downlink transmissions are via a horizontal wire antenna, and uplink transmissions via a vertical-axis loop antenna, for typical mine depths of 300, 600, and 1000 feet. Representative coal-mine overburden conductivities of 10-2 mhos/meter (moderate and common) and 10-1 mhos/ meter (high) were used; the former figure for both voice and narrowband calculations and the latter for narrowband calculations only. Examples of high, moderate, and low, surface and subsurface, harmonic and broadband-impulsive noise conditions were taken from NBS and Westinghouse (WGL) mine noise data, together with examples of high- and low-levels of ELF atmospheric noise taken from M.I.T. Lincoln Laboratory data. The effects of simple voice spectrum shaping techniques on the intelligibility of through-the-earth voice communications are examined, and indexes of intelligibility more broadly based than signal-to-noise ratio are discussed. Finally, a means of overcoming the affects of 60 Hz noise and its harmonics which are the largest contributors to typical audio frequency in-mine noise, is suggested. These feasibility calculations are not intended to serve as definitive and complete treatments, but as a starting point: to establish first-order estimates of the magnitude and variability of transmitter power requirements under different noise, overburden conductivity, and mine depth conditions; to identify relationships, conditions, or frequencies that are likely to limit or enhance system performance; to reveal items requiring further investigation and data still required; and to suggest practical methods for optimizing system performance. These objectives were met by the calculations. Simple experiments to support these calculations can and should be carried out; together with more detailed investigations of specific modulation, coding, noise-suppression, voice-compression and signal-conditioning techniques, aimed at producing through-the-earth operational/emergency mine-communication systems that are not only effective, but practical and economically sound.

Jan 1, 1974

By A. W. Deurbrouck

This Bureau of Mines report describes the washability characteristics of 14 coalbed samples collected in Wyoming. Such data is needed to evaluate the quality of the coals of the West where most of our low-sulfur-content coal reserves are found. Of the 14 samples included in this report 13 had a total sulfur content of 1.1 percent or less. All of the samples contained low per¬centages of ash or could be readily washed to a desirable ash level with minimal loss of yield. The coals ranged in rank from high-volatile B bituminous to subbituminous C, although 10 of the samples were high-volatile C bituminous. The coalbeds varied in thickness from 4.5 to an unknown thickness greater than 67.5 feet.

Jan 1, 1971

This Bureau of Mines report summarizes the research, development, and evaluation demonstrations conducted by the Bureau of Mines under the Health and Safety Act of 1969 to improve the means of notifying miners underground, who are away from their own phone, that they are being called.

Jan 1, 1977

By David C. Peters, Robert S. Crosson

A method of error analysis has been applied to the location technique of non-linear least squares iterative inversion in order to evaluate the resolving power of several seismic array configurations with various assumed earth models and errors and inaccuracies in arrival times. The results obtained demonstrate that lateral accuracies of location are improved significantly when the depth of the miner is known. Lateral location to within 100 feet appears achievable in many instances. If it is possible to refine earth models significantly beyond what has normally been assumed in this work by the use of on-site data, or if the mine is shallow (300 feet or less), accuracies of-about 30 feet or so may be attainable. Inaccuracies in earth models of about 5% are found to contribute much more heavily to these location inaccuracies than errors of a few milliseconds in picking arrival times; however, arrival time errors of 15-20 ms or above will dominate these model inaccuracies. The expected accuracy of location is found to fall off very rapidly as the miner moves outside the array. The strength of this effect depends markedly upon the geometry of the array configuration and can be reduced by careful design. Also, as the size of the array is increased, expected location errors within the array are not altered much, but continue to match the error associated with the smaller array over a larger area (assuming that all stations can still pick up the miner's signals). Better location accuracy, especially with respect to depth control is achievable in an earth where the velocity is depth-dependent (increasing with depth) than in one which is homogeneous. This is an advantage since the

Jan 1, 1974

By d&apos, Kathleen J. Amico

THIS SUMMARY appears in Minerals Yearbook volumes I and III, which cover mineral production in the United States, its island possessions, the Canal Zone, and the Commonwealth of Puerto Rico, as well as the principal minerals imported into and exported from the United States. The several commodity and area chapters contain further details on production. A summary table comparing world and U .S. mineral production also is included. Mineral production may be measured at any of several stages of extraction and processing. The stage of measurement used in the chapter is normally what is termed ?mine output." It usually refers to minerals in the form in which they are first extracted from the ground, but customarily includes for some minerals the product of auxiliary processing operations at or near mines.

Jan 1, 1965

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

MINE VENTILATION NETWORK ANALYSIS

Jan 1, 1977

By Robert J. Timko, Edward D. Thimons

Sulfur hexafluoride (SF6) is an odorless, colorless, nontoxic gas that has found acceptance as a tracer gas in research on ventilation pat- terns, measurement of air leak rates, respirable dust reductions due to bagging hood modifications, and the study of airflows relating to gob boreholes. Following a short review of the SF6 sampling technique, this report describes recent Bureau of Mines projects in which SF6 was used successfully as a tracer gas, enabling researchers to acquire representative data quickly and inexpensively.

Jan 1, 1982

By J. E. Hamak

This publication contains analyses and related source data for 165 natural gas samples from 21 States and 1 foreign country. Of the total samples, 155 were collected during calendar year 1988. The remainder were collected earlier, but releases granting permission to publish were not received until 1988. All samples were obtained and analyzed as part of U.S. Bureau of Mines investigations of the occurrences of helium in natural gases of countries with free market economies. This survey has been conducted since 1917. The analyses published herein were made by mass spectrometer and chromatograph.

Jan 1, 1989

By C. M. McCulloch, Maurice Deul

A geologic study of Mines 32 and 33 in Cambria County, Pa., was conducted as part of a methane control research program. Areas of high methane emission and roof instability are encountered which are related to the structural and stratigraphic features that characterize the geologic setting of these mines. Locally the folds trend N 20° E ±2°, the direction of the butt cleat in the Lower Kittanning coal. The face cleat strikes at N 69° W ±2° and the systematic rock joint in the surface bedrock strikes N 67° W ±2°This suggests that a directional stress oriented N 70° W produced the folds and influenced the directions of coal cleat and systematic joint sets. Analysis of SLAR indicates three directions of prominent regional lineation: N 39° E, N 31° W, and N 70° W. Little gas was encountered during development mining; large volumes of gas are encountered when roof falls. Most of the gas comes from strata above the mined coal; therefore, to control methane, roof instability must be controlled. Roof falls and high rates of methane emission are most likely where less than 30 feet of many thin layers of limestone, shale, and sandstone occurs between the Lower Kittanning coal and the next coal and in zones along the margins of a sandstone channel.

Jan 1, 1973

By John P. Gooch

The Bureau of Mines wrote a computer program which calculates the saturation curves and condensation characteristics of gaseous mixtures consisting of binary organic vapor and air. The program employs an algorithm which assumes an equilibrium mechanism for condensation, and the degree of fractionation obtained is predicted on the basis of relative volatility. The program incorporates a feature which allows the user to examine the fractionation resulting from condensation as a function of the size of the temperature increments over which condensation is assumed to occur. If a single. temperature interval between the dewpoint of the mixture and the outlet temperature of the condenser is assumed for the calculation, the results obtained will be those resulting from a single equilibrium condensation. If the condensation is assumed to occur over a number of temperature increments, the results obtained will approach those predicted by the Rayleigh equation as the magnitude of the temperature increments approaches zero. The results from calculations performed on vapor mixtures from organic heavy liquid solutions used in beneficiating potash and brucite ores are presented. The liquids are solutions of dibromomethane in trichloroethylene or perchloroethylene. The results show the degree of liquid recovery which is possible by cooling mixtures of organic vapor in air. Compositions of the vapor range from 10 to 95 percent air, and assumed condenser exit temperatures range from 110° to 50° F.

Jan 1, 1971

By P. G. Clites

This study was undertaken to determine the effect of consumable-electrode vacuum arc melting on the properties of copper and to determine the applicability of the process to the production of cast shapes of copper. Ingots and castings were produced from electrolytic tough pitch copper (ASTM designation ETP), from electrolytic cathode copper (ASTM designation CATH), and from oxygen-free copper (ASTM designation OF). The products of this study were evaluated to determine the effect of the melting process on the removal of impurities from the copper and on the physical properties of the copper. The results indicate that consumable-electrode arc melting can be satisfactorily applied to the melting and casting of copper. Ingots prepared directly from electrolytic cathode copper contained slightly higher levels of impurities than are found in commercial oxygen-free copper, Excellent results were obtained with centrifugal castings of unalloyed copper, and reasonably successful static castings can be produced if proper mold and gating systems are employed.

Jan 1, 1963

By Charles L. Kimbell

In broadest overview, a substantial part of the world's mineral industry in 1990 registered small gains over its 1989 performance, but traditional statistical measures of mineral industry performance, namely global production, trade, and consumption levels, failed to mirror these gains. This was because of the sharp downturns in the mineral industry activity in the U.S.S.R. and the former centrally planned economy nations of eastern Europe. These downturns in this one geographic area had influences on almost all traditional statistical series, in some cases simply significantly reducing growth, in other cases providing for a global downturn, in almost all cases despite considerably brighter outlooks based on activities in other world areas. To be sure, the U.S.S.R. and eastern Europe were not the only places on the planet suffering problems of one type or another in 1990 that impacted on minerals industry activity, but with the acquisition of information presently available, it seemed almost assured that the difficulties of these economies in transition will be the most difficult of problems to resolve in the long run. It certainly appeared that the legacy of the half century or more of economic central planning will be a decade or more of very difficult adjustments, and a number of these will greatly affect not only the minerals industry of these transition countries, but also the rest of the globe's mineral industry as well.

Jan 1, 1993

By R. O. Dannenberg

Applicability of the fluosilicate sintering process to recovering beryllium from beryl-spodumene concentrate analyzing 1.4 to 3.7 percent BeO (10 to 30 percent beryl) was investigated. The work was one phase of a Bureau of Mines research program undertaken to assess applicability of conventional processes and to devise new procedures for treating various potential beryllium feed materials. Beryllium recovery of about 70 percent in a product of 99-percent BeO grade was achieved in treating 3D-percent beryl concentrate. The process consisted of (1) sintering a briquetted charge of concentrate, soda ash, and sodium fluosilicate for 3 hours at 750° C.; (2) extracting the soluble beryllium by multiple stages of water leaching; (3) adding caustic to the leach solution and boiling to hydrolyze and precipitate crude beryllium hydroxide; (4) dissolving the crude beryllium hydroxide in sulfuric acid and separating the solution from undissolved silica; (5) sulfidizing the acid beryllium solution to precipitate heavy metal impurities; (6) adding ammonia to the clarified sulfate solution to precipitate beryllium hydroxide; and (7) converting the hydroxide to beryllium oxide (beryllia) by calcining at 900° C. About 60 percent more sodium fluoSilicate was required per unit of beryl than is used industrially in treating 10-to 12-percent BeO concentrate (80 to 90 percent beryl). Recovery decreased, and flux requirements increased, when treating concentrates containing less beryl.

Jan 1, 1963

By Thomas G. Carnahan

The Bureau of Mines conducted research to simulate in situ leaching of a chalcopyrite ore. The purpose was to obtain a direct comparison between moderate-temperature and elevated-temperature in situ leaching of copper trom minus la-inch ore and to analyze the sulfuric acid and oxygen requirements of the leaching system. Experiments employing oxygen were conducted at 35° and 90° C on 362-and 367-1b ore charges, respectively, under flooded conditions and at 400 psig. At 90° C, 47 pct of the copper was extracted in 913 days of leaching; at 35° C, 27 pct of the copper was extracted in 915 days. Diffusion into and out of the ore fragments con-trolled the rate of leaching. Oxygen consumption was 1.46 lb/lb of copper extracted at 35° C and 3.15 lb/lb of copper extracted at 90° C. Sulfuric acid requirements of the ore were 5.49 and 7.48 lb/lb of copper extracted at 35° and 90° C, respectively.

Jan 1, 1982