Search Documents

By A. J. Barry

[This is the third report related to fundamental retail roof-bolting research in underground mines (1, 2)3/ and describes an investigation of the torque-load relationship for 3/ -inch, expansion-type mine roof bolts. In a previous investigation the relationship between torque and bolt load was established for 1-inch slotted-type bolts (1). The two types of bolts differ in diameter and method of tightening and consequently may exhibit different torque-load behavior. The 1-inch bolt is tightened by turning the nut, the 3/4-inch bolt by rotating the beaded bolt itself. Experience indicates that roof bolts should be tightened to moors satisfactory anchorage sand to minimise nag of tie roof over the mine opening. The generally accepted means for determining the bolt load is to see a torque wrench to measure he torque applied in tightening the bolt and, from a predetermined relationship between torque and molt load, to, determine the corresponding bolt load. Because frictional effects may vary between one type of shell assembly or bolt and others, 7 types of expansion shell units and 3 types of 3/4-inch-diameter, mild steel bolts were tested.]

Jan 1, 1954

By R. V. Ramani

This report, Volume I of the seven-volume Final Report on the U. S. Bureau of Mines research contract no. G0254030 titled Application of a Total System Surface Mine Simulator to Coal Stripping with the Pennsylvania State University provides an executive summary of the purpose and scope, objectives and results of the research. The remaining volumes of the Final Report, listed below, describe in detail model development, input and output documentation and the three case studies. Under the project, an existing surface mine simulator, Open-pit Materials Handling Simulator (OPMHS) was modified and extended for application to surf ace coal mining. In addition, two equipment selection models, and a cost model were also developed. Volume II: OPMHS User's Manual Volume III: Equipment Selection Models Volume IV: Surface Mining Cost Model Volume V: Application of OPMHS to an Illinois Mine Volume VI: Application of OPMHS to a South Eastern Ohio Mine. Volume VIII: Application of OPMHS to a South Western Mine.

Jan 1, 1978

By Noel N. Moebs

The Bureau of Mines investigated severe coal mine roof support problems along a section of main entries in the Pittsburgh coalbed in southwestern Pennsylvania to identify the causative factors. The mine roof was examined in detail, and various sedimentary structures are described that contributed directly to irregular and unstable roof. Small-scale paleochannels, scours, and related slickensides were identified as the leading cause of bad roof, and isopach maps were prepared to illustrate a method whereby the presence of these structures could be inferred in advance of mining. Probably second in importance was the occurrence of relatively incompetent flaggy, poorly cemented sandstone, weakened by coal and micaceous laminea. No effect of in situ stresses on roof stability was detected.

Jan 1, 1977

By J. S. Tosh

An equilibrium study of the system potassium carbonate, potassium bicarbonate, carbon dioxide, and water has been conducted with solutions of 20-, 30-, and 40-percent equivalent potassium carboaate concentrations. These equilibrium data cover the operating range of the hot carbonate scrubbing system for removing carbon dioxide from gas mixtures. Such data are necessary to establish the limits of purification and are used to design absorption and regeneration towers. Values of K in the relationship K = (KHCO3)2/(K2CO3)PCO2 were determined for higher temperatures of 70" to 140° C. and greater concentrations, I 20 to 40 percent, than employed by previous investigators. For the 20- and 30-percent concentrations, K is constant at a given temperature; thus, once K has been determined the equilibrium pressure of carbon dioxide can be calculated for any conversion. Variation of & values with changing conversion was observed with the 40-percent solutions, so that equilibrium calculated pressures are less reliable from average K values.

Jan 1, 1959

By Douglas A. Donato

This Information Circular presents the MULSIM/PC system of numerical modeling computer programs developed by the U.S. Bureau of Mines. This system consists of four programs: PREMUL, the preprocessor or mesh generator; MULSIM/PC, the actual numerical modeling program (number cruncher); MUL3D, a three-dimensional postprocessor; and MUL2D, a two-dimensional postprocessor. These programs were specifically designed to operate on IBM-compatible (MS-DOS-based) personal computers for easy transfer of this technology to the mining industry and academia. MULSIM/PC uses a subvariation of the boundary-element method, namely, the displacement-discontinuity technique, for linear-elastic geomechanical analysis of mine plans in one or two parallel underground tabular deposits. Results calculated by this technique include stresses and displacements as they relate to changing mine geometries and materials. In addition to describing the MULSIM/PC program and its features, and providing a detailed example model, this report also documents the associated preprocessing and postprocessing programs that are part of the MULSIM/PC system. User's guides for all the programs are contained in the appendixes following the main report.

Jan 1, 1992

Great strides have been made in recent years to reduce the disaster potential of underground mine fires. However, mines can still be caught unprepared for a fire emergency. Fires can grow too large before they are detected, warning systems can be too slow and uncertain to reliably signal the danger, and suppression systems can be inadequate to extinguish the flames. New mining systems and equipment may create unanticipated fire hazards, and new materials may generate highly toxic combustion products. This report contains papers that summarize recent significant developments from the Bureau of Mines mine fire protection research program relating to these problems. Certain of these findings are also applicable to surface mining operations. The papers fall into the general categories of fire detection and instrumentation, fire warning, fire suppression, diesel equipment, spontaneous combustion, and toxicity analysis of combustion products.

Jan 1, 1988

By M. M. Tilman

The Bureau of Mines conducted research to evaluate superplastic behavior in commercial magnesium-base alloys AZ6IA, ZK60A, ZW3, AZ3IB, ZWI, and an experimental Mg-12 pct Al alloy. Strain-rate sensitivity indices (m-values), maximum elongations, and effects of superplastic elongation on tensile properties were determined on fine-grained sheet. Inert-gas-pressure hemisphere-forming tests were conducted on selected sheet stock of the five alloys. Formability trials on AZ31B alloy sheet were conducted on industrial equipment for comparison with commercial superplastic forming of Zn-AI alloy. Closed-die-forming tests were performed on extruded ZK60A rod. All alloys exhibited well over 100-pct elongation, indicating superplasticity, at temperatures and strain rates near the maximum m-values. Tensile properties were generally reduced following 100-pct superplastic elongation, but not to an extent that would preclude use of the commercial alloys in the superplastically deformed condition. The potential for industrial superplastic forming of AZ31B sheet was indicated by hemisphere forming in the laboratory and substantiated in industrial forming trials.

Jan 1, 1982

By John S. Berber

Bureau of Mines research on the production of phthalic anhydride by vapor phase oxidation of hydrocarbons began at Morgantown, W. Va., in October 1960. For these preliminary studies, a known solution containing naphthalene and 1-methylnaphthalene was used. In another series of tests, pure naphthalene was dissolved in different solvents. A series of investigations was conducted with the neutral oil fraction (210° to 270° C) of a low-temperature tar obtained from the Texas Power and Light Company's low-temperature carbonization unit. The neutral oil fraction was first dealkylated, and then the product was distilled into 210° to 250° C and 250° to 270° C fractions. These two fractions were then subjected to catalytic vapor phase oxidation. Although a number of catalysts was tested, most of the experiments were made using 9 percent vanadium pentoxide on inert alumina. The activity of this catalyst did not decrease after 162 hours at 1,030° F. Studies were conducted over a temperature range from 610° to 1,180° F. An operating temperature of 1,030° F yielded 47.50 percent of phthalic anhydride from a synthetic mixture of naphthalene and 1-methylnaphthalene. The highest yield (84.40 percent phthalic anhydride) was obtained with naphthalene dissolved in toluene and also with naphthalene dissolved in methyl ethyl ketone. With a 210° to 250° C fraction the highest yield of phthalic anhydride obtained was 12.32 percent at a temperature of 900° F, and, with a 250° to 270° C fraction, it was 15.80 percent at a temperature of 875° F.

Jan 1, 1963

By A. A. Giardini

This report represents the results of a literature study on boron nitride and related substances. The purpose of the study was to find Information that might be of value for production of a new, hard modification of boron nitride preferably in single crystal form. The report consists of a review of the major developments in boron nitride research, a discussion of the results, tabulations of physical and chemical properties;, conclusions drawn from the study, and a bibliography.

Jan 1, 1953

By Kathleen Madland Kowalski

In recent years the issue of human stress response in emergency workers has begun to receive attention. This paper presents a rationale for considering human stress as a significant factor in the management of emergencies. It discusses the concept of stress, Critical Incident Stress in emergency responders, and introduces the Critical Incident Stress Debriefing (CISD) process. It is suggested that, in a disaster, the CISD process can improve the effectiveness of response teams on site, their turnaround time on site, and post disaster time off the job. This paper, prepared by a US Bureau of Mines research psychologist, offers some ideas to the mining industry in general, mine rescue trainers, and more universally, to those responsible for developing emergency management plans.

By D. L. Boreck

Thick coal seams are common in the Western United States, Many seams are over 50 it thick (some are over 200 ft thick) and are too deep to extract using surface methods. Currently, such deposits are developed using standard "eastern" mining methods which only extract a few feet of total seam thickness, often rendering the remaining coal unminable with current technology. Novel methods that increase thick-seam recovery have been developed and are currently being used in Europe. These methods--high-face single-pass and multislice longwall, longwall caving, and hydraulic mining--have great potential for use in the United States. Successful use of these methods is an objective of the Bureau of Mines. Their use requires, among other things, a full evaluation of geologic features common to thick coals. The objective of this report is to present and summarize those features that will affect the introduction of the methods into thick-seam mines in the Western United States. The geologic elements delineated are three-dimensional configuration of the seam, cleat development, joints and fractures, roof and floor lithology, and faulting.

Jan 1, 1986

By Andrew B. Cecala

The Bureau of Mines conducted laboratory and in-mine tests on the Racal airstream helmet (Model #AR21) to evaluate its protection efficiency. Laboratory tests indicated that as ambient air velocity increased, the protection offered by the helmet decreased. In tests conducted at several coal mine long-wall sections with face velocities under 400 fpm, the helmet was 84 pct effective at reducing respirable dust in the miner's breathing zone. However, at a high-velocity section, 1,200 fpm, the efficiency of the helmet was significantly reduced, confirming our laboratory results.

Jan 1, 1981

By Lisa Steiner, Robin Burgess-Limerick

Working with or near underground coal mining equipment is hazardous because of the multiple sources of energy and adverse environmental conditions. Of the 4169 injuries reported to Coal Services during the three years to June 2005,447 were associated with continuous miners, 232 with LHD (load-haul- dump) vehicles, 140 with shuttle cars, and 140 with personnel transport - a total of 959, or 23% of all injuries reported during the period. An analysis of the injury narratives accompanying these injury claims highlights a number of opportunities for controlling injury risks. Using the frequency of reported injuries for the prioritisation of risk control strategies has limitations because of the tendency to underestimate the importance of relatively uncommon but potentially high consequence events. Injury reports also underestimate the contribution of risk factors such as whole body vibration, which have a long-term cumulative contribution to an elevated risk of injury. However, taking these limitations into consideration, the results of the injury narrative analysis suggests the following hazards as the highest priority for elimination or control: • handling continuous miner cable • strain while bolting • slipping off continuous miner platform • inadvertent or incorrect operation of bolting controls, and operation of controls while a person is in a position of danger • hitting potholes or other roadway abnormality • collisions while driving underground vehicles

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

6. Development of Mine Sealant Material Systems 6. 1 Introduction The preliminary evaluation of material systems described in Section 3 led to the selection of the following four promising systems for further development: System A: Aggregate, Fly Ash System System B: Aggregate, Fly Ash, Urethane Foam System System C: Aggregate, Bulkhead, Light Expansive Concrete System D: Aggregate, Self-Supporting Thick Slurry Preliminary laboratory tests indicated that the building of effective bulkheads from one borehole would be extremely difficult. Two extra boreholes would be required adding to the overall cost of the system and making the system less attractive. Tests with light expansive concrete showed that bulkheads would be required, the material would not support itself. As a result, further development of this system was terminated. Foam concrete was selected as the most suitable material to be developed into a self-supporting, rapid-setting slurry. A laboratory investigation of its use for mine sealing was conducted during this program; the results are summarized in Section 6. 5 and details of the laboratory program are presented in Appendix B.

Jan 1, 1973

By Verne S. Mutton, William A. Slivensky, Eric S. Weiss, Kenneth L. Cashdollar, Deepak R. Kohli

The National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Laboratory, cooperated with Tecrete Industries Pty. Ltd. and BHP Australia Coal in a research program to evaluate the strength characteristics and air leakage of four seal and two stopping designs for use in underground coal mines. A fundamental safety research area for NIOSH is to eliminate the occurrence of coal mine explosions or to mitigate their effects. One approach to achieve this goal is to develop new and innovative seal designs that provide increased explosion isolation protection for the mining personnel against ignitions that originate from within the gob or. other worked-out areas of the mine Full-scale seals and stoppings were constructed in the Experimental Mine at Lake Lynn Laboratory near Fairchance, Fayette County, PA. They were ail--leakage tested, then subjected to a series of explosions with average pressure pulses ranging from 25 to 500 kPa (3.5 to 72 psi). Instrumentation measured seal displacement and acceleration as a function of time, providing data to assist in the development of numerical models 1'01- future seal design. All three seals designed with Meshblock wire forlnwo~-k ant1 a lnonolithic shotcrete core withstood the first explosion test, which generated an avcr-age rnaximu~n pressure of - 140 kPa (-20 psi) while maintaining acceptable air leakage rates. These seals I-anged from 175 to 325 mm thick. They included a 2.7-m-high by 325-mm-thick seal that was tesled 27 hr after completion against this - 140-kPa explosion pressure, a special requirement of the test program. This seal survived explosions with pressure pulses up to 300 kPa (43 psi). The 2.3-m-high by 325-mm-thick Meshblock seal survived three explosion tests with overpressures up to 455 kPa (66 psi) and satisfied the air leakage criteria. A I ,200-mm-thick plug seal was constructed of two Gunmesh formwork walls in-filled with shotcrete and a 3,450-kPa (500-psi) strength Aquablend core. This plug seal survived three explosions with pressure pulses ranging 11-om 150 lo 430 kPa (-22 to 62.5 psi) with no measurable postexplosion air leakage. Two Gunmesh stoppings with thicknesses 01' 40 and 75 inln withstood explosion overpressures of 23 and 115 kPa, respectively. Anchoring all seal and stopping designs into the roof, ribs, and floor with steel "rootbolts" provided very effective boundary constraint that is critical to the performanceofstructures subject to explosion overpressures.

Jan 8, 1999

By J. Burlin Johnson

In small-scale blasting experiments conducted in the Bureau of Mines laboratory, small charges were used to produce craters in blocks of concrete mortar. The results are compared with larger scale experiments of other research workers, and the comparison demonstrates the similarity of the results obtained and indicates that small-scale blasting should be a useful tool for predicting large-scale blasting effects. INTRODUCTION The purpose at this investigation was to conduct blasting experiments in mortar in the laboratory and then, by comparing the results with those from larger scale field blasts in rock to determine to what extent, if any, the laboratory results resemble those in the field. The work described herein was the initial phase of a project aimed at evaluating small-scale blasting as a tool for use in improving blasting techniques. It is evident from the stand-point of control and cost that small-scale blasting would be valuable in the study of rock fragmentation by blasting in mines and quarries, if the extrapolation is valid.

Jan 1, 1962

By J. G. Croeni

The titanium-iridium alloy system was investigated to determine whether alloys of this system would merit further development as control-rod material for nuclear reactors. A study was made to determine the titanium-iridium phase diagram by using melting-point, thermal analyses, X-ray diffraction, dilatometric, electrical resistivity, and metallographic techniques. The titanium-iridium alloy system was investigated between 500° and 2,400° C. Results indicate the formation of two intermetallic compounds, Ti3Ir rind TiIr3, and one intermediate solid solution centered about the 50 atomic percent iridium composition. A eutectic reaction occurs at 1,475° C, and 19 atomic percent iridium. The Ti3Ir decomposes peritectically at 1,520° C. The intermediate solid solution exhibits a maxima of 2,140° C. at 50 atomic percent iridium. This phase is also believed to undergo an order-disorder transformation at 1,750° C. Another eutectic reaction takes place at 2,000" C. and 60 atomic percent iridium. The compound TiIr3 formed at 75 atomic percent iridium decomposes peritectically at 2,115° C. Further increases in iridium content result in the formation of an iridium-rich terminal solid solution. Information obtained below 900° C. in titanium-rich alloys indicates that iridium acts as a beta stabilizer in titanium, and the authors believe that a eutectoid decomposition of beta-titanium occurs near 500° C. and 10 atomic percent iridium.

Jan 1, 1962

By Mary S. Esfandiary

This list of organizations that conduct research and development programs on coal has been compiled by the Bureau of Mines with the thought that such a directory may provide a useful guide to worldwide research efforts in the areas designated and may facilitate communication between organizations with similar interests. This list includes government, university, private, and commercial organizations. Many of these groups are conducting comparatively modest but often particularly interesting or specialized investigations. The areas of investigation have been defined in a broad manner--these include analysis and constitution, mining and geology, preparation, combustion, briquetting, high- and low-temperature carbonization, gasification, hydrogenation, Fischer-Tropsch, and health and safety. In some instances such information is not available, but the names of the organizations themselves often indicate immediate arias of interest. Special publications issued by and describing the work of each organization have been cited, when known; almost all of the organizations also publish results of their investigations in the technical press. Several foreign technical and trade publications that include such information and are not published directly by any of the organizations listed are cited in the pages following the list of organizations in each country. This list is not complete. Information that would improve coverage and/or accuracy will be welcomed by the Bureau of Mines.

Jan 1, 1961

By Samuel P. Harteis, Eric S. Weiss

The National Mining Association and the Mine Safety and Health Administration requested that the National Institute for Occupational Safety and Health (NIOSH) conduct full-scale evaluations of a recently developed carbon fiber-reinforced polymer (CFRP) reinforcement technique for upgrading existing mine ventilation seals to withstand an explosion pressure of 50 psi or greater. The evaluation was conducted in the NIOSH Pittsburgh Research Laboratory’s Lake Lynn Experimental Mine (LLEM) near Fairchance, PA. The purpose of the evaluation was to determine the blast resistance of the CFRP reinforcement technique, designed to increase the strength of two types of existing 20-psi-rated in situ mine ventilation seals. Two candidate ventilation seals were selected to represent the 20-psi alternative seal designs typical of those used in mines prior to July 2006. Installed within the LLEM were (1) a 4-ft-thick pumpable cementitious foam seal using material with a designed 150- to 200-psi average compressive strength at 28 days and (2) a 24-in-thick, low-density cementitious block seal with a center pilaster and keyed to the floor and ribs. The materials necessary for the CFRP reinforcement technique were then installed on the outby (active) side of each seal, and the seals were subjected to explosion overpressures. Both seals with the CFRP reinforcement retrofit successfully withstood explosion pressures of 60 psi or greater during the full-scale evaluations in the LLEM.

Jan 1, 2008

By R. E. Lindstrom

Effective separation of rare-earth mixtures is obtained using hydrogen as a retaining ion at 200° F with ethylenediaminetetraacetic acid (EDTA) eluant. Results obtained in Bureau of Mines bench-scale apparatus and large columns with hydrogen as a retaining ion closely parallel those obtained with copper as a retaining ion. The use of hydrogen as a retaining ion permits EDTA and water, collected before rare-earth breakthrough, to be recovered in a form that allows the material to be recycled without extensive processing. With the exception of yttrium and dysprosium, separation of rare-earth mixtures is improved and throughput is increased by elevated temperatures. Separation with 1,2-diaminocyclohexanetetraacetic acid (DCTA) eluant increases markedly on increasing temperature from ambient to 250° F; however, on the basis of separation efficiency, DCTA does not compare favorably with EDTA.

Jan 1, 1962