Search Documents

By George S. Scott

The Bureau of Mines conducted ignition, flammability, and decomposition experiments on gas mixtures containing ethylene to determine its flammability characteristics at elevated pressures and ambient temperatures. Pure ethylene was found to propagate a decomposition reaction at 1,000 psig and ambient temperatures when ignited with 1 gram or more of guncotton in a 2-inch-id bomb. The decomposition products were primarily carbon, methane, and hydrogen.

Jan 1, 1965

By Edward W. Parsons

The explosive-expansion center-hole anchor was designed and developed for the specific purpose of use as a component of an instrument system that measures differential ground movement within a small drill hole in rock. Such anchors should have an unobstructed center hole, should be installed without a twisting action which could tangle connecting wires, and should be capable of being installed at depths in excess of 100 feet. The anchor has a thick-walled center tube and a thin-walled outer tube. Low-energy detonating cord, wrapped around the center tube and detonated with a mild end primer, expands the outer tube to produce anchorage. The explosive-expansion center-hole anchor can be installed easily in drill holes of any inclination but cannot be installed under water. Centering of the anchor is critical with regard to its subsequent holding power. The anchor is safe to make and handle.

Jan 1, 1965

By James R. FitzSimmons

This report describes an instrument developed by the Bureau of Mines as an improved device for examining roof rock in bolt holes. The unit consists of a commercially available fiberoptic unit adapted for use as a flexible stratascope. Field testing in both metal and coal mines has shown the instrument can be easily transported and used by a single operator. The size and flexibility of the instrument eliminate the need for specially drilled holes.

Jan 1, 1979

By Michael G. Zabetakis, Aldo L. Furno, George H. Martindill

Hydrazine vapor is flammable in the absence of air at elevated temperatures and atmospheric pressure . The minimum concentrations of benzene , toluene , m- xylene , cumene , and n- heptane needed to inhibit flame propagation through vapor mixtures of hydrazine and hydrocarbon were determined at 125 ° C and atmospheric pressure . These concentrations can be correlated with either the heat of formation or the heat capacity of the hydrocarbon .

Jan 1, 1964

By A. W. Khair, L. D. Gehl

"This paper describes the mechanism of coal and rock cutting from quasi-static indentation through dynamic indentation to rotary cutting. The results indicate that during quas~static indentation, a crushed zone, and subsurface fractures develop. The crushed zone is a potential source of dust generation. Dynamic indentation produces a crushed zone due to the frictional resistance offered by the coal or rock during penetration of the bit. Confining pressure changes the mode of failure from tension to mixed tension and shear. The wider bit causes larger crushed zone and more dust generation. The rotary cutting is a combination of quasi-static and dynamic indentation which results in chip formation. 1. INTRODUCTIONThe trend from conventional mining to continuous machine-cutting of coal, using more productive machinery is inexorable. Intolerable levels of dust generated at the face is an indication of inefficient coal or rock cutting by these machines. The Federal Government of the United States paid about 11.7 billion dollars workman compensation to more than 470,000 miners with Coal Workers Pneumoconiosis (Newmeyer, 1981). Bieniawski and Zipf (1985) reported that annual benefit payments were about 2 billion dollars. The need for research m improving coal cutting 1s therefore paramount. The enactment of Health and Safety Act in 1969 in the United States triggered the initial investigation into coal cutting mechanism and cutting tool design. The European countries were also engaged in the same area of research, however, their emphasis was in the use of wedge shaped bits. In 1981, the United States Bureau of Mines commissioned the South West Research Institute to investigate the effect of operating parameters mainly on airborne respirable dust in order to provide a healthier and safer atmosphere for coal mine workers.A research program by the Department of Mining Engineering, West Virginia University, USA was initiated to study the fragmentation mechanism during coal/ rock cutting. The research program was divided into three areas of research, namely quasi-static indentation, dynamic indentation and rotary cutting."

Dec 1, 1995

By A. R. Elliott

In the early part of the your 1919 the Bureau of Mines undertook a study of methods of handling oil after it had buon produced, with the view of pointing out the losses due to evaporation and other causes. Observations on present methods show that the oil is subject to largo losses in both quantity and quality from the time it loaves tho well until it is recoivod by the pipe-lina company. During this time it is splashed into four or more tanks of various sizes and with little or no protection over the tops. From the settling tank, where the flow of oil is tamporarily stopped in order to permit sparation of ter and sediments, through the gago tanks and leaso gathering tanks to the largo tank storage where it is hold for many days, rich gasoline vapors roadily escape, especially from tho ghor gravity oil. As no effort is made to measure the oil before it reached the storage tanks, where it is delivered to the pipe-line company, the lossos of the light products of the oil can only be approximated, and, as final results will show, are no doubt usually very much underestimated. In conducting this investigation, the Bureau has endeavored to make tests that would show quantities and values lost, in order to impress better upon those concerned what might be saved through a little more diligence. Eperiments were conducted on both California and Mid-Continent oils. The field operimental work done in California, on which a report is to be published in the near future, is cutlined briefly below: The field work consisted in collecting from operating companies data on storage of oils in large tankage and in performing experiments in the field on storing and piping oil to small lease tanks under practical conditions. Acourate Easurements were takon on the volume, gravity and gasoline content of the oil as it passed through the various stages in its removal from the lease. The work extended over the four seasons of the year in order to obtain better the effect of varying winds and high and low atmospheric temperatures during those periods. Thanks are due to the many oil operators who have taken a personal interest in the work and gave valuable information and assistance. One company furnished the oil and tanks and much of the apparatus and labor. This company also per- mitted the work to be done on its properties in the Coalinga field. This was of material aid, as the results were to be comparative and therefore it was necessary that the same gravity oil be used throughout the experiments.

Oct 1, 1920

By Richard V. Ageton

Compressed- air blowers are frequently used both in large and small metal ines , not only as an aid to ventilation , but in some mines as a substitute for an dequate ventilation system . As a temporary fixture , blowers have their uses , but hey should never be used in lieu of a permanent ventilation system. A number Probably the most common error made in placing dependence on compressed- air lowers as an aid to underground ventilation is the tendency to over- rate their cooling efficiency . It is a very common but natural error to assume that compressed air which issues freely from a blower is of the same temperature as the compressed air which issues freely from the exhaust port of a rock-drilling machine . of readings were taken in different mines of the temperature of the rock- drill exhaust , of the compressed air flowing from the blowers , and of the surrounding air In both cases . In general , the temperature of the rock- drill exhaust was from 10 to 30 degrees below that of the surrounding air , in many instances being slightly below freezing , 32° F . The average temperature for a number of compressed-air lowers and for the mine air surrounding them is shown in Table I.

Jan 1, 1922

By A. J. Miscoe

A unique machine for inducing bending fatigue in wire ropes was built at the U.S. Bureau of Mines' Pittsburgh Research Center. This machine can produce nine levels of degradation through repetitive cycling of long samples of wire ropes of the types used in the mining industry. This report provides an analysis of the results of the first wire rope to be fatigued on this machine. These results have indicated that as a wire rope accumulates bending cycles, its strength first decreases because of wear and then in-creases due to cold working of the wires. As the amount of cold working increases, more and more of the embrittled wires break and the strength of the rope decreases rapidly. In this test, application of several of the regulatory retirement criteria to various sections of the rope suggests that there may be some inconsistency among them.

Jan 1, 2010

By H. O. McDonald

Solutions containing Cr6+ and sulfuric acid are used in a number of surface-finishing operations. Substantial quantities of chromium and copper are lost and pollution problems are created when the spent solutions are discarded. To minimize the undesirable environmental effects while improving secondary resource recovery technology, the Bureau of Mines is conducting research to detoxify and recover metals from these solutions. Spent etchants are treated to remove copper and reduce Cr6+ to Cr 3+ in an electrolytic cell. The anodes and cathodes are granulated coke. The spent solution is continuously pumped through the electrodes. Hexavalent chromium is reduced to trivalent chromium, and copper is recovered at the cathode. Reoxidation of Cr3+ at the anode was not observed. The removal and recovery of copper reduction of Cr6+ lessen chemical demand and increase efficiency in waste in treatment operations associated with the use of these solutions.

Jan 1, 1980

By McHenry Mosier

Diamond -drilling blast holes at Eastern Magnetite Mine C is proving economical in boundary shrinks , in removing pillars not readily accessible for percussion drilling , and in driving scraper drifts . The cost per foot drilled is greater than for percussion drilling , but savings in associated factors outweigh this handicap . The rocks drilled include trap rock and magnetite ore . The mining method is the panel , block- caving system utilizing scraper sublevel drifts instead of branch raises to convey the ore to the haulage level . Diamond -drilling blast holes was begun early in 1945. Three rigs equipped with noncoring bits are now in active operation two shifts per day . They are owned by the company , and the drill operators are paid by the day . In shrinkage stopes the drill is mounted on a horizontal bar set against opposite walls of the stope . Stoping holes are horizontal , which gives better results in blasting and requires fewer set ups . In scraper drifts the drill is mounted on a horizontal bar clamped to two columns about feet apart . Trim holes around the periphery of the drift and reliever holes are drilled 50 to 80 feet in length . A 10 - foot wedge cut drilled with a stoper is blasted in conjunction with a corresponding length of the trim holes to effect a 10 -foot advance of the full- sized drift . Recent drilling averages 97 feet per machine shift , excluding time utilized in setting up and moving the machine , hand mucking , and barring down . The feet drilled per bit at present is 417. These data represent the average for drilling in both rock (waste) and ore . Percussion drilling utilizes three types of wet drills . Detachable bits are standard . Gage changes for new bits is 1/8 inch and for reconditioned bits 1/16 inch . The life of a bit is five uses . Resharpening is on contract . A drill carriage is used in haulage headings .

Feb 1, 1948

Treat contaminated coal mine drainage to meet EPA and State water quality requirements. Approach A model (fig. 1) is presented for selecting, designing, and sizing one or several passive mine drainage treatment systems that can be used in remediation of abandoned mine lands (AML). The three principal types of passive mine drainage technologies for the treatment of coal mine drainage are an aerobic system, a compost wetland, and an anoxic limestone drain. The multistep approach presented here provides a simplified method to characterize the type and magnitude of the water quality problem and then to select either a single treatment system or a combination of treatment systems to address the specific site situation. How It Works Step 1. Discharge Characterization. Characterization of the discharge consists of measuring the discharge flow rate and collecting water samples at the point of discharge for chemical analysis. Both the flow rate and chemistry of a discharge can vary seasonally and in response to storm events. It is important to account for this variability by determining flow rates and water chemistry under various conditions.

Jan 1, 1992

By A. D. Garman

This paper presents one of a series of digests of foreign mining legislation and court decisions which is being prepared in advance of a general report relative to the right of American citizens to explore for minerals and to own and operate mines in various foreign countries . This interpretation of the laws of Nicaragua has been prepared from the best available information in Washington , but is released subject to correction and amplification , if necessary, by the proper American diplomatic and consular officers to whom it is being referred through the courtesy of the Department of State .

Jul 1, 1930

By Richard A. Andre, R. Larry Grayson, Thomas Simonyi

"INTRODCICTIONThe search for the cause(s) of coal workers' Pneunoconiosis continues despite the vast amount of research that has been undertaken over the past forty to fifty years. Good correlation between the mass of dust inhaled over workers' lifetimes and the incidence of the disease has led to the development of effective environmental standards and implementation of good procedures for the control of dust generation and dispersion in the working place. Research has only begun, however, to uncover the biochemical mechanisms involved in initiating the disease.Correlation between the rank of the coal seam in which miners worked and disease incidence and severity is acknowledged worldwide, but the agents in the higher rank coal seams which cause CWP arc still not defined. The basic components of the coal seams, i.e., the elements and minerals, are generally known, but the way in which they interact with human pulmonary cells is largely still a mystery.The process of disease development is a biochemical one which depends on the characteristics of the pulmonary cells within their immediate biochemical environment and the characteristics of invading respirable coal mine dust particles, probably both chemical and physical ones. The cell-particle relationship, therefore, must be defined, and both cells and particles must be characterized according to properties which potentially are involved in the disease process.Following such characterization, specific respirable dusts from different coal seams, which appear to have different effects on coal workers, must be obtained or constructed and then used in experiments designed to determine dust toxicity or the response of animals exposed to the dusts.The results presented here focus on characterizing properties of respirable coal mine dust particles collected from operating longwalls in West Virginia and Virginia Longwall panels were selected for analysis because the respirable dust in the coal face areas is largely uncontaminated by rock dust and analysis of the dust yields results unconfounded by rock dust."

Jan 1, 1990

By W. E. Wallace, S. -G. Xing, M. J. Keane, J. C. Harrison

"SummaryDiesel-exhaust particles from two sources were dispersed in aqueous mixtures of dipalmitoyl phosphatidyl choline, a major component of pulmonary surfactant, and were tested for genotoxicity. Diesel samples from the same sources were extracted with dichloromethane and transferred into dimethyl sulfoxide and subjected to the same assays. Both types of extractions yielded similar results in both the Salmonella mutagenicity assay and the sister-chromatid exchange assay using V79 cells. After separation of the samples into supernatant and sediment fractions, the activity of both diesel samples was shown to reside exclusively in the supernatant fraction for the solvent-extracted samples, and exclusively in the sedimented fraction for surfactant dispersed samples. These findings indicate that genotoxic activity associated with diesel particles inhaled into the lung may be made bioavailable by virtue of the solubilization / dispersion properties of pulmonary surfactant components.While diesel engine emissions are associated primarily with transportation, they are also very common in the workplace. Estimates for the U.S. are that as many as 1.35 million workers in as many as 80 000 workplaces are exposed to the combustion products of diesel engines (NIOSH, 1988). These occupations include, but are not limited to mining, agriculture, motor vehicle maintenance, fork lift truck driving, truck driving, and tunnel and bridge operation."

Mar 1, 1992

By P. S. Lewis

Shortage of natural gas is reviving interest in low-Btu fuel gas made by gasifying coal in fixed-bed producers. The Bureau of Mines gasified strongly caking Pittsburgh bed coal over test periods lasting four days in an experimental gas producer located at Morgantown, W. Va, Mechanical stirring throughout the fuel bed was effective for keeping the fuel moving and this stirring made the operation successful; hence, the gas producer was named the stirred-bed producer. Nuclear density gages were applied as control instruments to indicate coal flow and fuel level, and to record the frequency and location of void spaces in the bed, The gas, of nominal 140 to 165 Btu/scf calorific value, could be burned in a boiler for generating steam.

Jan 1, 1972

By Charles L. Kimbell

In overview, the world's mineral industry in 1989 registered gains over its 1988 performance, but these gains were by no means as pronounced as had been those of 1988. The traditional statistical measures of mineral industry performance, namely production, trade, and consumption levels, reflected significant growth in most industry sectors from crude material extraction through the gamut of down- stream processing. Growth in market economy countries generally exceeded growth in the centrally planned economy countries as a result of a variety of causes that will be covered subsequently, but even among the centrally planned countries there were some upturns. In contrast to these measures of the soundness of the industry, the situation for nonfuel mineral and metal prices was less satisfactory than in 1988, and low crude oil prices continued as a problem for the all-important petroleum sector, despite some gains during the year. The oil price situation mitigated against price increases for competitive fuels. Although this was unfavorable for fuel producers, it remained advantageous to consumers, including nonfuel mineral producers, processors, and transporters. Thus it cannot be viewed as a negative factor for the whole of the global mineral industry. Global crude mineral output value was estimated at nearly $1,420 billion in current dollars, an increase of 9% over the 1988 level, and an increase in current dollar terms for the seventh consecutive year. Measured in terms of constant dollars, however, adjusting for inflation, the increase was only 4.7% compared with the 1988 level. Despite the prolonged growth trend, the 1989 crude mineral output value level was still 3.2% below the record high set in 1980, which was $1,467 billion in terms of 1989 dollars.

Jan 1, 1992

By Eugene V. Cilento, R. Clark Lantz, K. A. DiGregorio

"This laboratory bas developed a sensitive electro-optical method to quantify the initial rate (R) and total amount (MAX) of superoxide (02) produced by single pulmonary alveolar macrophages (PAM). The method uses a microscope-based TV system to visualize PAM in culture, and to video record the images during the time the cells produce 02. MAX and R are calculated from measurement of temporal changes in optical density in the images due to precipitated diformazan formed by the reaction of O2-, produced by each PAM, with nitroblue tetrazolium present in the culture medium. To date, values of Rand MAX, measured due to adherence of PAM to the dish, have been compared to values obtained when quartz, coal mine dust (CMD), and kaolin . were added to the medium (in vitro). Rand MAX have also been calculated for PAM lavaged from animals exposed to quartz and CMD in the WVU Inhalation Facility. Presently, experiments are being done using which will permit PAM to be restirnulated by different dusts to help establish a dose response relation~ p and a means to study the role of lung surfactant on modifying the acute toxicity of inbaled dusts. Ultimately, this methodology should provide useful insight into establishing the role of 02 in PAM dysfunction due to inhalation of dusts, and in lung diseases such as pneumoconioses. INTRODOCTIONPAM are free cells found in the lungs which protect the lungs by removing foreign debris and bacteria. This is accomplished, in part, by the process of phagocytosis, whereby foreign matter is internalized into vesicles known as primary phagosomes. Phagocytosis also involves the chemical breakdown of inhaled dusts and the killing of microbes. Detoxification is aided by the respiratory burst, which is a metabolic response of the cell to foreign substances, that results in the production of highly reactive oxidizing agents from the partial reduction of extracellular oxygen to superoxide (02) at the surface of the plasma membrane. Superoxide undergoes either spontaneous or enzyme catalyzed dismutation reactions to form hydrogen peroxide (H202) and subsequently hydroxyl radical (OH•) and singlet oxygen (02 t ). However, while these oxygen metabolites aid in the killing of microbes they also may destroy endogenous tissue. For example, 02 has been linked to the aging process and to many diseases including emphysema, diabetes, and cancer.'' Therefore, a better understanding of the production of 02 is extremely important since an abnonnally low production could result in damage by inhaled dusts and bacteria while an abnormally high production could result in direct damage to the lung tissue by the phagocytes. Inhalation of respirable sized mineral dusts, such as quartz (silica), coal mine dusts (CMD), and asbestos, results in various pulmonary disorders. PAM are thought to play an important role since evidence suggests that the first step in fibrogenesis is an interaction of dust particles with PAM. Generally, in vivo exposure of animals to mineral dusts results in increased respiratory burst activity, migratory patterns, phagocytic behavior, and secretory potential of PAM, and for this reason these have been implicated to be pivotal events in the pathogenesis of pulmonary diseases.1 In addition to stimulation of resident PAM, an influx of monocytes into the lung and/or production of new macrophages generally occurs in response to fibrogenic dust inhalation. Further, PAM may attract and stimulate fibroblasts, which normally synthesize proteins and collagen during rep~ of tissue, by secreting chemoattractants and enzymes. Thus, PAM may be involved in pulmonary disorders through failure or partial loss of their defensive capability, or indirectly, through release of other mediators."

Jan 1, 1990

By D. E. Fogelson

In a factorial experiment, blasting caps were detonated in three sizes of shotholes in mortar with three types of stemming--dry sand, wet sand, and hydrostone. Free-surface displacement pulses were recorded with a capacitive-displacement gage at a distance of 15 inches. The effects of decoupling and the type of stemming on the amplitude and the duration of the displacement pulse were determined. Both the amplitude and the duration of the displacement pulse were significantly decreased by increasing the decoupling, but they were little affected by the type of stemming.

Jan 1, 1965

By Keith G. Wallace

Coal mine ventilation systems are often subject to high leakage rates. As a result, changes in airflow resistance will strongly affect the efficiency with which air is delivered to the working place. One major source of airflow resistance is the line brattice used to direct air from the last open crosscut to the working face. Because it is a great distance from the fan, the resistance of the line brattice can result in more overall leakage than an equivalent resistance closer to the fan. Substituting auxiliary fans for brattice eliminates this source of resistance, with improvements in system efficiency and cost. Also, in some mines, the leakage that leads to spontaneous combustion can be reduced. The benefits obtained by several different brattice and fan substitutions have been studied by Mine Ventilation Services, Inc., Lafayette, CA, under contract to the U.S. Bureau of Mines. Changes in main fan duty were compared with additional costs associated with auxiliary fans. Results indicate that in some circumstances, considerable leakage reductions and cost savings are possible.

Jan 1, 1990

By McHenry Mosier

The diamond-drill method was tried at the site selected for driving a 5- by 6 -foot air shaft at the east end of the Bellefonte mine . This method of sinking consisted , first , of drilling a 5-3/4 -inch-diameter cut hole from the surface , then drilling parallel 1.5 - inch ( EX ) holes around it at appropriate distances for a balanced blasting round . The cut hole was not charged with explosive but served as a relief chamber for the incipient expansion of the ground broken by. blasting the surrounding 1.5 - inch holes . The length of each hole was 236 feet , which was the finished depth of the shaft . The nature of the work in the air shaft was largely experimental , and many difficulties arising from the lack of special equipment and proper technique for precise alinement of the drill holes caused expensive delays before they could be overcome . Drilling the 5-3 /4 - inch hole , which was impeded by frequent core blocks in the core barrel , required 10 shifts . average advance per shift for an EX hole was about 150 feet . The The holes were charged and fired from the surface . The length of the section blasted in one cycle was 10 feet . Blasting progressed from the bottom of the shaft upward . The broken stone dropped into a chute , from which it was drawn into cars on the haulage level . The Bellefonte mine is an underground limestone mine.3/ The primary objective in undertaking the research on shaft sinking by diamond drilling was to perfect a method for driving connections between levels of the mine .

Oct 1, 1948