Search Documents

By Ellsworth R. Spencer

A lightweight fiberglass feed leg for hand-held pneumatic percussion rock drills has been fabricated and tested by the Bureau of Mines. Its lighter weight facilitates easier handling of the rock drill apparatus, thereby reducing the potential for back injury to the driller and in- creasing drilling productivity. Current hand-held feed leg drills of the same class are 50 pct heavier than the Bureau-devised feed leg drill, which is comprised of a reduced-noise drill and the fiberglass feed leg. In-mine tests of the fiberglass leg showed that its performance and cost are comparable to those of standard aluminum feed legs.

Jan 1, 1985

By H. C. Ko

As part of the Federal Bureau of Mines effort to provide thermodynamic data for the advancement of minerals technology, energy conservation, and environmental preservation, the standard enthalpies of formation of a-magnesium sulfate, a-magnesium sulfate, and magnesium sulfate monohydrate were determined by hydrochloric acid solution calorimetry. The values of the standard enthalpies of formation in kcal per mole at 298.15 K are -307.95 ± 0.13 for a-MgS04, -307.03 ± 0.13 for ß-MgS04, and -384.72 ± 0.13 for MgS04 .H2O.

Jan 1, 1979

By John C. LaScola

The Bureau of Mines repeatedly surveyed a grid of monuments over an active longwall mine panel in southwestern Pennsylvania during a 1-year period. Both conventional ground surveying techniques and photogrammetry were used. The objective of this investigation was to compare elevation measurements of subsidence obtained from aerial and ground survey methods under dynamic ground conditions. The results of a statistical analysis of the survey data show that the mean of the differences between 372 matched pairs of elevation measurements was 0.20 ft (61 mm) with a 95-pct-confidence interval of 0.05 ft (15 mm). The mean of the absolute values of the differences was 0.38 ft (116 mm) with a 95-pct-con-fidence interval of 0.04 ft (12 mm). Ninety-five percent of the absolute values of the differences were less than 1.11 ft (338 mm).

Jan 1, 1988

By E. J. Gleim

For many years mining men have sought for a portable device that would be direct reading and permit more positive detection of methane than was possible with flame safety lamps, which depended so largely on the training, skill, and personal ability of the user. Through the years, after the discovery that methane contributed to many mine explosions, considerable effort and large sums of money have been expended in searching for and developing instruments that would be practical, and, at the same time, reliable and safe to use. Very early in the history of the Bureau of Mines, some of its engineers were unsuccessful, after many trials, in attempts to develop such an instrument. Commercial firms, however, persisted in research until today a number of instruments are on the market that have proved to be practical in coal-mine service. It is hoped, however, that further research will bring about improvements in accuracy and other desirable features. BUREAU OF MINES STANDARD FOR METHANE DETECTORS The Bureau of Mines recognized the need for establishing minimum requirements on which to base official approval of suitable Instruments. This standard was prepared as Schedule 8. It was revised before being issued in printed form. The revision was published as Schedule 8A in 1920 and was revised on two other occasions. The present edition, known as Schedule BC, was issued October 31, 1935.

Jan 1, 1954

By G. R. Hopkins

One of the largest items in the expense of operating a refinery is the cost of the fuel used in distillation and for miscellaneous purposes such as in the heating of buildings and in the generation of electricity. On a B. t. u. basis, the average refinery consumes approximately one-tenth as much fuel as it produces. Theoretically, the fuel consumption at refineries should be much smaller than this, but furnaces can not be designed to be 100 per cent efficient and, in addition, a large part of the waste heat is low-temperature heat which would not pay for the expense of recovering it. Annual surveys of fuel consumption at refineries have been made by the United States Bureau of Mines, beginning with 1925. During the 5-year period, 1925-1929, the refineries made steady progress in fuel economy. This is evidenced by the computed figures of heat requirement per carrel of crude oil refined, which show a decline from 829,000 B. t. u. in 1925 to 639,000 B. t. u. in 1929 (see fig. 1). In 1930, however, 'the trend in fuel economy was reversed and the quantity of heat utilized in refining the average barrel of crude oil rose to 672,000 B. t. u. There were undoubtedly a number of reasons for the apparent decrease in fuel economy at refineries in 1930, chief of which were the tendency to carry the distillation farther instead of merely topping the crude and a gain in the consumption of waste oils, such as acid sludge, which in actual practice yield less heat per unit consumed than has been theoretically assigned to oil.

Jan 1, 1931

By David C. Oyler

Methane-drainage holes must be completely filled by grout before mining to prevent the emission of large quantities of gas during mine-through, which would constitute an explosion hazard. In November 1980, seven horizontal holes at the multipurpose borehole, a small-diameter shaft drilled as a Bureau of Mines coalbed methane-drainage installation on the property of the Federal No. 2 Mine, Monongalia County, WV, were plugged using a sodium silicate gel grout. This report de- scribes the grout mix and the use of the grout at the multipurpose borehole, and discusses the results observed upon mine-through of the holes in early 1981. Cost data for the sodium silicate grout are also presented.

Jan 1, 1984

By W. E. Young

This paper describes operations of the Chief Consolidated Mining Co. at the Chief mine in the Tintic district, Juab County, Utah, where the outstanding problem is water control; the unique pumping methods employed are featured in this report. The ore bodies in this district occur as long, narrow shoots along fault fissures, usually in the Bluebell dolomite of Ordovician age. Oxide ores predominate above the 1800 level, which is also the natural water level. Sulfide ores containing lead, zinc, silver, and gold extend below the 1800 level. The mine is developed by vertical shafts and winzes, from which drifts are driven to the ore bodies. In the lower levels of the mine these drifts extend long distances from the shafts or winzes because of the relatively low dip of the ore shoots. The mine has been worked to the 2800 level and the 18-411 winze extends to the 3080 level.

Jan 1, 1958

By Nabil A. Bibawy

The U.S. Bureau of Mines has established a method for the calibration of class 2 and class 4 standards of mass using a procedure from designs developed by the National Institute of Standards and Technology (NIST). This method produces a weight calibration that is within 1.0 pct of the balance sensitivity. A set of four 1-kg weights yielded a standard deviation of 3.25 mg compared to ±2.91 mg balance sensitivity. The method employs the use of a high-accuracy balance to measure the difference between a set of weights calibrated by NIST and the set to be calibrated. The error of the balance is included in the error for each weight calibrated.

Jan 1, 1989

By D. A. Baker

This report describes the elemental characterization of chromite and related materials at the Bureau of Mines, Albany Research Center. Analytical methods for determining the major constituents, representing extensive experience, refinement, and development, are described and fully annotated. This presentation should allow other laboratories to use these methods and obtain comparable results with a minimum of time needed for familiarization with individual methods.

Jan 1, 1990

By R. R. Brandenthaler

A series of open-flow tests was conducted in the Chickasha gas field, Grady County, Oklahoma, during June, 1927, under the direction of the U. S. Bureau of Mines and at the request of the Oklahoma Corporation Commission. The purpose of these teats was to determine whether or not any differences existed in the open-flow volume of a gas well when taken through well-head nipples of different diameters, and further, to establish if possible a relationship between open-flow volumes taken through well-head nipples of various diameters. The open flow of a well is the volume or quantity of gas, measured under standard conditions, that a well will produce when open to the atmosphere. There are several methods used for determining the open flow of wells; some of the methods are more suitable under certain conditions than others. The Pitot tube method is the simplest, is applicable to almost any condition, and is the one most commonly used. In the tests described in this paper no attempt was made to compare the Pitot tube method with the minute pressure measurement method or the orifice measurement method.5

Jan 1, 1928

By Michael J. Magyar

This report contains a cost estimate of the Bureau of Mines process for dewatering Alaskan placer effluent streams with polyethylene oxide (PEO). In this process effluent slurry is withdrawn from the placer plant pond system after a primary settling stage. A dilute PEO solution is injected into the slurry line to flocculate the fine, suspended solids. The flocculated solids are dewatered on a stationary screen. Clarified water is returned to the placer operation or discharged, while the 35 percent solids waste is pumped back into the mine cut. Cost estimates are presented for dewatering plants processing 1,000 gallons per minute of effluent slurry at three representative turbidity levels. Both the placer and the dewatering plants operate on the same 1-shift-per-day, 6-day-per-week schedule for the 100-day Alaskan operating season. Estimated fixed capital costs for these plants processing placer with effluent turbidities of 1,000, 3,000, and 5,000 nephelometric turbidity units (NTU) are approximately $29,000, $31,000, and $34,000, respectively, on a fourth quarter 1986 basis. Operating costs are estimated to be $0.34, $0.37, and $0.40 per thousand gallons of effluent slurry.

Jan 1, 1987

By Jr. Taylor

The following heats of solution have been measured in 1.160 molal H2SO4 at 25° C: AH298, kcal./mole Be(c) + 77.44(H2SO4?47.849 H2O) H2(g) + BeSO4 (soln) -92.83 ± 0.11 BeSO4 ?(c) + 77.44 (H2SO4?47.849 H2O) BeSO4(soln) -16.45 ± 0.02 BeSO4?2H2O(c) + 77.44(H2SO4?47.849 H2O) BeSO4?2H2O(soln) -5.395 ± 0.019 BeSO4?4H2O(c) + 77.44 (H2SO4?47.849 H2O) BeSO4?4H2O(soln) 1.513 ± 0.010 Combining these data with other experimental results and data taken from National Bureau of Standards information yielded the following heats of formation at 298° K:

Jan 1, 1966

By E. J. Kloos

Bureau of Mines-approved self-contained breathing apparatus of the compressed air demand type were evaluated for performance at low temperature. Apparatus durations, breathing resistances, and airflow rates were measured on machine tests at room temperature and -25° F. Man tests under actual wearing conditions verified the machine test results. Many serious functional changes in apparatus performance occurred at low temperature. Pressure regulators malfunctioned when diaphragms lost flexibility. Under certain conditions frozen condensed moisture sealed exhalation valves and fogged eyepieces. High-pressure leaks, not encountered at ordinary temperature, developed at low temperature. Tests results are discussed generally and specifically for each apparatus. Recommendations are given to obtain optimum performance from demand type breathing apparatus at low temperatures.

Jan 1, 1968

By V. F. Parry

Under the present emergency every consumer should store as much coal as he can. Although there is no shortage of coal, there is likely to be a shortage of labor to mine excessive quantities in the fall, and railroads cannot be expected to deliver coal promptly on account of the need for transporting war materials. Some miners must join the armed forces, and those who are left may be unable to mine coal as rapidly as you will need it when winter comes. When the first cold days arrive, there may be a shortage of trucks to deliver coal. Deliveries may be planned in advance, and your turn might not come until it is too late.

Jan 1, 1942

By David C. Oyler

Three long horizontal holes were drilled from a directionally drilled surface hole at the Emerald Mine near Waynesburg, Pa. The purpose was to adapt the technique of directional drilling for use in draining methane from coalbeds. A 504-m (1,652-ft) long, 76-mm (3-in) diameter, circular arc pilot hole was drilled, using a downhole mud motor, to enter the Pittsburgh coalbed at a vertical depth of 305 m (1,000 ft). The hole was reamed to 222 mm (8-3/4 in) and was cased to a measured depth of 486 m (1,595 ft). Three 76-mm (3-in) diameter horizontal drainage holes were then drilled, totaling 2,909 m (9,544 ft) of horizontal hole. Improvements in drilling methods increased the average drilling rate from 20.4 ill (67 ft) to 64.9 m (213 ft) per day. The cost of drilling the directional and horizontal holes (using a Government-owned drill rig) was $1,169,530, a figure inflated by inexperience and by delays caused by lost-circulation problems and fishing operations. An estimated total drilling cost of $960,000 (including rental of a drill rig) for an improved system, was determined by a detailed cost analysis. Initial gas and water production from November 1979 through May 1980 was low because of caving of the horizontal holes drilled in shale near the bottom of the casing.

Jan 1, 1982

By R. H. Thompson

Six different types of blasting caps, mainly of the type used in coal mines, were evaluated to determine both their 1lF and DC characteristics. Two of the caps were of foreign manufacture. All the American made caps had "no-fire" (0.1% firing probability with 95% confidence, as determined by the Bruceton test) levels above 0.04 watts. One of the caps of foreign manufacture had a "no-fire" level of 0.023 watts. A worst case analysis of blasting cap pick up of RF power in coal mines was performed and safe distance curves were generated.

Jan 8, 1973

By C. L. Klingman

In extracting helium from natural gas at Bureau of Mines helium plants, a continuous analysis of the helium content of inlet and outlet gas streams is required to determine extraction efficiency. An analyzer, using established principles of gas chromatography to effect the analysis, has been developed by the Bureau of Mines to meet this need. It will record the helium content of inlet or discharge gases from helium-extraction plants every five minutes, continuously, without the attendance of an operator. A 25-inch column of activated charcoal is used as a partitioning agent; nitrogen is the carrier gas; and a hot-wire, thermal-conductivity cell is the detector. A 1.0 mv, strip chart indicates the unbalance of the detector cell, Sample size is 0.37 cc, and carrier gas flow rate is 75 cc, per minute. Significant improvements in helium extraction have been demonstrated by using the chromatograph in three helium-extraction plants.

Jan 1, 1961

By Charles P. Lazzara

Concentration profiles of low-pressure, slightly lean CH4-02-Ar flames have been measured in situ for the following unstable species: oxygen atom, hydrogen atom, hydroxyl radical, methyl radical, and formyl radical. The observed maximum mole fractions were 2.0X10-2 for H, 1.1X10-2 for OH, and 0.8X10-2 for 0; the maxima occurred in the recombination zone. Methyl and formyl radicals have maximum mole fractions in the reaction zone of 2.2x10-3 and 6x10-5, respectively.

Jan 1, 1973

By Alan A. Bergeron, J. L. Michels, R. L. Collins

Advanced communication and monitoring systems were developed and demonstrated in three underground mines representing different mining techniques, geographical areas, and material mined. The first mine was a large coal mine in western Pennsylvania that used room and pillar techniques and continuous mining methods. The system developed for this mine provided private telephone channels, environmental monitoring, and control of underground equipment, all on a single coaxial cable, with all system operations under the direction of a minicomputer. Many advanced features were incorporated into the system, such as paging of roving personnel, two-way section wireless, through-the-earth emergency communication, and redundant signal paths. Television was multiplexed into the system for underground equipment surveillance. A hoist radio system completed the complement of equipment at the mine. The second mine was a magnetite ore mine in eastern Pennsylvania that used block caving mining techniques. A radio system was developed that provided two-way communications between trackless vehicles and roving personnel. A unique system of uhf/vhf repeaters combined with a flleaky-feeder" transmission line offered operational and emergency features not previously found in mine communication systems. Evacuation alarming, personnel paging, fan-hole drill operator communications, and maintenance and safety vehicle dispatch were provided. The system required no dispatcher and operated during power failure. A hoist communications/shaft inspection system completed the installation. The third mine was a deep silver mine in the Cour d’Alene district of Idaho. The system developed for this mine utilizes a single wire pair to provide up to 14 voice channels. A unique combination of PBX, telephone carrier system, and intercoms offered private conversations, selective signaling, and emergency backup communications. Two hoist communication systems were installed to provide a voice link and in-cage belling signal between hoistman and cage.

Jan 11, 1981

By Frank D. Lamb

Pyrophyllite, a hydrous aluminum silicate (Al2 Si4O10 (OH)2 ) has been mined in North Carolina and marketed without beneficiation for the past 100 years, but recent demands for higher-grade material indicate that an economical concentration method is needed for at least a part of the pyrophyllite production. Past production has depended upon selective mining and hand sorting, which is often unsatisfactory because of the finely disseminated character of the ores. The major impurity in North Carolina pyrophyllite ores is quartz, which accounts for the abrasiveness of the commercial product. Since pyrophyllite is only slightly heavier than quartz, those ores cannot be beneficiated by simple gravity-concentration methods. Some separation can be attained by differential grinding and air classification because of the difference in hardness of the two minerals) but the separation is not sharp. Froth flotation of pyrophyllite from Quartz has never been attempted commercially, but if the demand for high-grade material is sufficient, it would seem that this process offers the most premise of being economically feasible.

Jan 1, 1950