Search Documents

This part of the final report treats some problems related to coal mine carrier frequency communication systems using the trolley wire/track transmission line. This work was undertaken for a brief period of time during the summer of 1972 to help understand, quantify, and improve some of the trolley wire carrier system behavior observed and/or predicted. Calculations and estimates of transmission line characteristic impedance, inductance and capacitance per unit length, mine motor loading effects, parallel line effects, and connection impedances are presented in Chapter I. Chapter II treats the design of r-f isolators for reducing the undesired and troublesome r-f loading that mine motors present to the trolley transmission line. Chapter III treats a diversity method for combatting standing wave nulls. I. CALCULATIONS RELATED TO TROLLEY WIRE COMMUNICATIONS A. ESTIMATION OF INDUCTANCE AND CAPACITANCE PER UNIT LENGTH OF TROLLEY LINES To estimate the L and C per unit length of trolley lines, we use the eccentric line model of Section G of this Chapter, "Characteristic Imped¬ance Estimates for Mine Trolley Lines." The capacitance per unit length for an eccentric line is given by (1)

Jan 1, 1974

Provide a means of recovering precious metal values from finely ground tailing materials. Approach Determine the procedures needed for agglomerating the finely ground material for subsequent heap-leach cyanidation of the precious-metal-bearing tailings. Applying Agglomeration/Heap-Leaching to Fine Tailings Agglomeration technology was developed by the Bureau of Mines to provide cost-effective recovery of precious metal values though better heap leaching of clayey or low-grade ores. While many precious metal producers have adopted this technology to reclaim precious metals from crushed ores and wastes, other operations have experienced problems in using the heap leaching technique effectively on piles of fine tailings. In contrast to the coarser ore and waste material, most tailings piles contain more than 50 percent minus 200 mesh materials with no coarse material. Fine particles and clays present in the pile can impede 8 uniform flow of the leaching solution through the heap, thus preventing efficient and cost-effective precious metals recovery.

Jan 1, 1986

By Eric B. Sansone

The Federal Coal Mine Health and Safety Act of 1969 requires coal mine operators to sample accurately the amount of respirable dust in the mine atmosphere. A technique approved for such sampling employs a 10 mm nylon cyclone followed by a membrane filter (nominal pore size ????= 5 µm) and a pump. The pump is required to provide a flow rate of 2.0 ± 0.1 liters per minute. Calibrations have yielded a range of flow rates (1.4 to 2.8 1pm) at which the cyclone should be operated to remove the non-respirable portion of the dust. The purpose of this project was to evaluate the performance of the 10 mm nylon cyclone at flow rates of 1.8 and 2.0 1pm using a polydisperse coal dust aerosol. The penetration characteristics of the cyclone were to be compared to the United States Atomic Energy Commission's respirable dust standard. The effect of relative humidity on cyclone penetration characteristics was also to be observed.

Jan 1, 1973

By James J. Jessop, Richard E. Thill, Michael J. Friedel

As part of an investigation aimed at improving the health and safety and competitiveness of the mining industry, the U.S. Bureau of Mines evaluated the application of common offset radar profiling, using a 250-MHz ground-penetrating radar (GPR) system, for the detection of fractures in igneous rock. A series of radar reflection surveys were conducted to detect and delineate the extent of fracturing at various granodiorite and gabbro quarries and outcrops located in Minnesota. The application of radar profiling for detecting joints, sheeting fractures, shear zones, and depth to water table was demonstrated to be feasible with minimal processing. Radar reflection interpretations were verified by visual inspection of the rock mass and field mapping of local structure. The radar reflection section provides a simple, rapid, and cost-effective means for mapping of shallow (less than 10 m) small-scale fractures (greater than 0.25 cm) in igneous rock masses (characteristic of velocities between 0.061 m/ns for gabbro and 0.125 m/ns for granodiorite). Depth or distance estimates to fractures are within 10 pct of the actual, and time-shift compensation is necessary only when topographic irregularities exceed 30 cm.

Jan 1, 1992

By H. E. Powell

Over 5 million lb of chromium, 1 million lb of nickel, and 90,000 lb of molybdenum are lost annually in the dusts generated in the production of stain-less steel. Additional losses of these metals in the form of mill scale and grinding swarf may be double the dust losses. This Bureau of Mines report describes a process for recovering these and other metals in the form of an alloy steel suitable for recycling. Zinc and lead, when present in the wastes, are recovered as byproducts in the form of oxide fumes. The laboratory-scale process (10-to 25-lb charges) recovers up to 95 pct of the chromium, 100 pct of the nickel, and 100 pct of the iron. The resultant alloy contains from 10 to 20 pct chromium, 6 to 12 pct nickel, and 55 to 65 pct iron, with lesser amounts of molybdenum and manganese. The alloy is essentially free of zinc, lead, and sulfur. The zinc-lead fume obtained from the treatment contains about 40 pct zinc and 20 pct lead and represents essentially complete recovery of these metals.

Jan 1, 1975

By W. H. Lewis

This Bureau of Mines report and its companion report (Information Circular 9073) have been prepared as a complete reference on underground coal mine lighting. This report discusses system design criteria and procedures, data and specifications to aid in selection of suitable mine lighting hardware, and guidelines for system installation and maintenance. Topics include light measuring techniques and instruments, illumination regulations for underground coal mine environments and equipment, lamps and ballasts, available mine lighting hardware, design and evaluation of coal mine illumination systems, and installation and maintenance of a mine lighting system.

Jan 1, 1986

By I. O. Salyer

This research was conducted with the objective of suppressing the respirable dust in coal mines by foam application. A formulation was developed for making a water-based, high-expansion, and limited stability foam. A horizontal boring machine was used as a laboratory coal mining model for generating coal dust. A modified laboratory foam generator was built. Foam was applied directly to the point at which dust was being formed by the cutter of the boring machine working against a block of coal. Coal dust was sampled with an impinger and analyzed for the particle count and particle size distribution. Coal dust suppression test results on freshly generated dust have demonstrated very clearly that in laboratory scale experiments over 90% of the respirable coal dust can be suppressed by foam. These tests were run when initial coal du t concentrations were 10 and 70 million particles per cubic foot (mppcf).

Jan 1, 1970

By Yael Miron

Coal mines that undergo self-heatings, and specifically mines that sustain both floor heave and self-heatings, would benefit from the use of sealants to minimize air ingress to susceptible areas. The U.S. Bureau of Mines(USBM) evaluated three sealant systems for this purpose, bentonite-water mixtures, silicate gel, and guar gum gel. The guar gum-based gel was the only sealant that possessed the desired properties of elasticity, ease of preparation, adaptability to the mine, and a long life. In addition, since the gel consists mostly of water, it could quench or cool nearby heatings. Optimal formulations were determined in laboratory tests, and then tested in the USBM Safety Research Coal Mine. Two formulations resulted in stable gels that lasted for at least 12 months in the mine. Semi continuous preparation of gel using an eductor was evaluated and appears feasible. Although guar gum gel is expensive, selective use to prevent heatings in specific areas would be cost-effective, both interms of productivity and enhanced mine safety.

Jan 1, 1995

By B. D. Sartwell

The formation of alloyed regions near the surface of metals using ion implantation is being investigated by the Bureau of Mines as a means of providing corrosion resistance using much smaller amounts of the strategic alloying metals. Two ion implantation systems that can implant low-energy chromium, nickel, or aluminum ions into low-cost substrate materials such as iron or carbon steel have been designed and constructed. The development of the ion source, ion beam acceleration stage, mass analysis system, and target chamber are described in detail. The ion-implanted alloys have been characterized using proton-induced x-ray emission to give the total number of atoms implanted and to determine the extent of any surface contamination introduced by the ion implantation process. Research conducted at other laboratories on metallurgical applications of ion implantation is given.

Jan 1, 1980

By M. Hertzberg

This Bureau of Mines report describes experimental and theoretical studies of diffusion flames in free convection. The cross-coupling between buoyancy-induced flows and the combustion process is explored as it relates to the size, structure, and radiative balance of flames. New data are presented for the size-dependent radiance oscillations of diffusion flames and for the angular distribution of the total radiant intensity from a small methanol pool flame. Both amplitude and frequency of the measured oscillations are compared with theoretical predictions that are based on a new view of the structure of diffusion flames. This new view, which is at variance with the traditional one, assumes uniform reaction in the diffusive mixing zone, and recognizes the significance of the role played by convective buoyancy and its duality in both aiding and impeding flame propagation. Buoyancy quenches propagation at low burning velocities, introducing a real discontinuity in the combustion rate. A "flammable volume" is thus defined as that bound between lean- and rich-limit contours. However, in the flow disturbances generated by combustion waves that consume that volume, buoyancy aids propagation by promoting the convective mixing of a new flammable volume. The measured radiance oscillations are manifestations of these propagation and remixing cycles.

Jan 1, 1978

By P. E. King

The U.S. Bureau of Mines is conducting an ongoing research project to better understand the phenomena involved within electric arcs utilized in electric furnace steelmaking. With a better understanding of the physical and electrical characteristics involved, dynamic or predictive control of electric arc furnaces may be possible. A mathematical model is presented, but not solved, and the system of coupled equations is analyzed. Characteristic parameters are used to determine relative importance. In this manner, significant quantities are dermed. The parameters found to contribute little to the system of equations of motion are ignored. A resultant simplified system is identified, and directions for further study are indicated toward control of electric arc furnaces.

Jan 1, 1990

By James A. West

The South Asian countries of India, Pakistan, Afghanistan, Ceylon, Nepal, Bhutan, and Sikkim arc to varying-degrees just beginning to achieve significant economic and industrial development. These countries are richly endowed with certain mineral resources, and development of these resources is being accelerated. In 1965, the mineral industry remained a relatively small sector of the region's economy, accounting for only about 1 percent of its estimated gross national product of $62,528 million. Nevertheless, the estimated $630 million total value of minerals produced in South Asia during 1965 represented an increase of nearly 15 percent t over that of 1964. India continued as the dominant mineral producer of the region, accounting for 85 percent of the total value of all minerals produced ill 1965. India increased its output of iron ore, manganese, mica, coal, and petroleum. Pakistan accounted for 13 percent of the value of the region's output and recorded increased output of iron ore, chromite, coal, natural gas, and most other minerals. The small mineral industry of Ceylon attained remarkable growth in the production of ilmenite, graphite, and gem stones. The mineral industry of Afghanistan remained relatively insignificant, although development of large known resources of natural gas was continued, Nepal, Bhutan, and Sikkim produced no commercially significant quantities of minerals in 1965.

Jan 1, 1967

By D. E. Hirsch

The Bureau of Mines has developed a systematic procedure for separation, characterization, and semiquantitative analysis of high-boiling (350° to 550° C) distillates of crude oils. Isothermal and molecular distillation were used to prepare the 370° to 530° C distillate of Recluse, Wyo., crude oil. The distillate was separated into fractions by chemical treatment, silica-alumina gel adsorption, and gel permeation chromatography (GPC). The fractions were analyzed by use of GPC correlations and mass and nuclear magnetic resonance (NMR) spectrometry. The increased knowledge of petroleum composition obtained from the data will contribute to improved petroleum processing and utilization and energy conservation.

Jan 1, 1974

By Margaret M. Ragin

In a cooperative effort between the U.S. Bureau of Mines and the Florida Institute of Phosphate Research, with input from the phosphate industry, the conversion of phosphogypsum to sulfur has been investigated. The first step in the conversion scheme involves reduction of phosphogypsum to calcium sulfide. Effects of temperature, catalyst, reaction time, and type of reductant (carbon monoxide and coal) are discussed. It was determined that phosphogypsum could be reduced to calcium sulfide at 850° to 1,000° C using either coal or carbon monoxide as the reductant. The required temperature was lowered to 750° C using ferric oxide or magnetite as a catalyst for the reduction reaction. Results indicate that as the volatiles content of the coal is increased, reaction temperature may be decreased to obtain a given conversion, or if the reaction temperature is maintained constant, the conversion can be increased. Best results were 95- to 100-pct conversion using a high-volatile coal at 800° to 850° C. Addition of a catalyst increased calcium sulfide yield when low- or medium-volatile coals were used as reductants, but had little effect when high-volatile coals were used.

Jan 1, 1990

By J. M. Singer

The objective of this investigation was to determine minimum air velocities and entrainment rates for coal and rock dust dispersion in wind tunnel experiments under conditions that simulate dispersion from surfaces in coal mines where airflows are induced by weak gas explosions. Dust deposits were bed-or ridge-shaped; particle sizes were 6 to 80 microns (cohesive deposits) or 100 to 150 microns (free-flowing deposits); and wind tunnels were 7.62 cm wide by 5.08 cm high by 300 cm long, and 2.4 m wide by 1.5 m high by 215 m long. The investigation showed that minimum air velocities (directed at mid-height) of separate, layered, or mixed piles of coal dust and rock dust were within the range 5 to 30 m/sec, independent of size of wind tunnel. This finding considerably facilitates scaling of data to mine-size passageways. Free-flowing deposits dispersed relatively slowly by single-particle detachment; cohesive dusts dispersed faster by the breaking and lifting of large clumps along weak failure flames; particle dispersion occurred in flight. Layered or mixed deposits of coal and rock dust did not disperse selectively. Semiempirical expressions were derived relating minimum air velocities and dispersion rates to dust-pile geometry, cohesion, porosity, and bulk density.

Jan 1, 1972

This report presents test results, data evaluations, and typical system performance expectations based on wireless electromagnetic propagation measurements performed in the MAGMA Copper Company's San Manuel mine near Tuscon, Arizona during March 30 through April 2 1981. In particular, and at the Bureau's request, this work was coordinated with testing of MF prototype vehicular radios being developed by A.R.F. Products, Inc. with USBM support under Contract H0308004 as part of a system to be marketed by Mine Safety Appliance Co. This testing also employed a prototype vehicular antenna developed by Terry S. Cory, P.E. with USBM upport under previous Contract P0382223. The work was performed under USBM contract J0308012, Propagation of EM Signals in Underground Metal/Non-metal Mines. The authors wish to thank Mr. Hank Seany, Manager of Mines and Mr. Bob Zerga, Mine Superintendent who so kindly arranged for the visit. Particular thanks are given to Mr. Al Metcalf who arranged the logistical details of our underground work, and whoa forward thinking program toward improving general mine communications at MAGMA provided the test-bed context for evaluation of the prototype equipment. The authors also wish to thank Benny Jiminez, Paul Ayala, Lorenzo De La Cruz, and Kent Billhartz for their day-by-day support of the testing. Mr. Jiminez's effort was instrumental in performing the testing, and he also provided a detailed understanding of the existing multi-level, multi-frequency trolleyphone system at MAGMA. the authors are also indebted to Dr. Larry Stolarczyk of A.R.F. for numerous detailed consultations on MF technology, and who was present and participated in the majority of the testing. 1.1 GENERAL BACKGROUND ON COPPER MINING AT MAGMA the San Manuel mine is the largest copper mine in the U.S., efficiently extracting copper and molybdenum sulfide from the low-grade San Manuel ore body.This ellipsoidal ore-shell body, with major workings located 2000-3000 feet mbelow the surface, has ore shell thickness varying between 100 and 1000 feet over a longitudinal extent of some 8000 feet, and with major & minor crossectional axes of about 5000 and 2500 feet respectively. The San Manuel mine operation employs in excess of 1000 men/shift with gross ore production between 60,000 and 70,000 tons/day. The mining operation employs the block caving technique; actively being implemented on three levels (2075,2375,2675 feet for haulage, and 2015,2315,2615 product/grizzly levels). The ore haulage is largely via D.C. trolley trains to four (3A,3B,3C,3D) product shafts for skipping to the surface. An additional three shafts at two locations are used to convey men, materials, and developmental rock extractions into and out of the mine. On each haulage level, the trains carry ore an average of two miles one-way from the ore raises to the dump points. 1.2 TOPOLOGICAL BRIEF OF THE HAULAGE LEVELS The 2375 level, on which all the testing was conducted, is illustrated in

Jan 1, 1981

By Paul J. Barrett

The Bureau of Mines evaluated a sulfurous acid-sulfuric acid process for recovering alumina from clay, in which clay is leached. successively with sulfurous acid and sulfuric acid. The resulting aluminum sulfite and aluminum sulfate solutions are combined and heated to produce a basic aluminum sulfate and sulfur dioxide. Alumina is extracted from the basic aluminum sulfate as sodium aluminate by leaching with dilute sodium hydroxide. After desilication, sulfuric acid is used to precipitate alumina as alumina trihydrate, which is then calcined to alpha-alumina. The estimated fixed capital cost for a plant producing 1,000 tons per day of alumina is about $74 million on a 1971 basis. For comparison with previous alumina-from-clay evaluations, the estimated fixed capital cost for the plant is about $67 million on an M and S Chemical Equipment Index basis of 24.0.0, which is equivalent to a 1960 cost level. Because the operating cost is highly dependent on fuel and electric power costs, graphs are included to show the effect of these items on the operating cost. On a 1971 basis, with natural gas costing 35 cents per million Btu and operating labor costing $4 per hour, the estimated operating cost is about $100 per ton of alumina. On a 1960 basis, with labor costing $2.30 per hour and natural gas costing 25 cents per million Btu, the estimated operating cost is about $86 per ton of alumina.

Jan 1, 1973

By Gordon T. Austin

The combined value of production of natural abrasives, which include tripoli, special silica stone, garnet, staurolite, and emery, decreased about 24% in 1992. The decrease in the value of tripoli production was the result of a decrease in total production. Emery decreased owing to a decrease in the volume of the material produced. Special silica stone experienced a significant increase in unit value and decrease in the quantity produced. Garnet showed a 6 % increase in quantity and a 36 % decrease in unit value. Staurolite decreased about 27 % in the quantity produced and value compared with those of 1991. The fused aluminum oxide industry showed a slight increase in the quantity produced and a 4 % increase in the value of production. The silicon carbide industry saw a 7 % increase in the quantity produced and a 10 % increase in the value of production. Combined, the industries increased 4 % in quantity and 6 % in value compared with those of 1991.

Jan 1, 1992

By M. W. Price, Joseph V. Mather, E. H. McCleary

"INTRODUCTION The asphyxiation or poisoning of workmen in underground mines by noxious gases from blasting in adjacent strip mines can be prevented.Considerable progress has been made in eliminating or reducing hazards to the health and safety of underground workmen in anthracite mines, but seldom does a year pass without reported cases of underground workmen being poisoned by the fumes from blasts of explosives in strip-mining operations. In the early days of the anthracite industry, the coal near the surface was only partly mined, and many small stumps of pillars and barrier pillars were left standing; these pillars are now being recovered by stripping. It has become necessary to give more consideration to the effects of blasting at strip mines upon the quality of the air in underground mines adjacent to stripping operations.Special precautions are taken by the .personnel of the Jeddo-Highland Coal Co., whose mines are near Jeddo, Luzerne County, and near Centralia in Columbia and Schuylkill Counties in the anthracite region of Pennsylvania, to prevent asphyxiation of workmen by carbon monoxide or other toxic gases resulting from blasting in strip mines. The procedures established by the Jeddo-Highland Coal Co., are given in this circular so that others may benefit thereby and thus avoid hazards to underground workmen where mining is carried on under similar circumstances."

May 1, 1949

By A. A. Campoli

Retreat pillar mining concentrates stresses on workings directly outby gob areas, which can result in coal mine bumps. The development of bump-control design criteria by the U.S. Bureau of Mines was furthered by data from a novel bump control mining method at the Olga Mine, McDowell County, WY. The pillar splitting, retreat mining system induced large pillar pressure increases and roof-to-floor con-vergence. Roof-to-floor convergence monitoring proved to be a valuable tool in evaluating the pillar splitting mining method and localized destressing techniques. Maximum strain energy storage in chain pillars appears to have occurred just prior to the first of four split cuts. At that point a 15-ft-wide, highly fractured perimeter confined the core of the 55-by 70-ft pillars, permitting the pillar core to support tremendous pressures. Splitting the chain pillars into two 17.5-by 70-ft wings removed the confinement load, resulting in pillar yield. Thus, the pillar splitting mining method successfully redistributed the weight of the roof away from the pillar line. Shot fire and auger drilling destressing techniques aug-mented the pillar splitting mining method by redistributing the weight of the roof.

Jan 1, 1989