Search Documents

By D. R. Dolinar, J. Pablic, D. C. Oyler, T. P. Mucho

At a mine in central PA, high horizontal stresses have caused long running roof falls resulting in hazardous conditions for the miners and the premature abandonment of panels. Because of these conditions, the mine requested assistance of the National Institute for Occupational Safety and Health (NIOSH) in utilizing the 'advance and relieve method to mitigate the affects of horizontal stress on the mine roof. "Advance and relieve" mining involves the removal of a pillar or a portion of a pillar during development, thereby creating a cave along one side of the panel. Following cave development, the horizontal stress is relieved over the workings adjacent to the cave in the active panel. The mine has used this system in three panels with a significant reduction in stress damage and no large roof falls.

By R. E. Morgan, Barkleym J. F.

"INTRODUCTION Wood burned for commercial heat and power usually is waste material from some manufacturing process. The amount of it reaches substantial proportions. It is estimated that over 50 percent of the timber cut for lumber becomes ""waste"" in the process - sawdust, shavings, trimmings, slabs, and bark. Woodworking manufacturing processes also produce much waste. The incentive to use this waste has resulted in much development of wood-burning equipment to produce heat and power. To answer general inquiries received by the Bureau, this publication covering developments along these lines was written. There is included a bibliography of additional information on the subject.COMPOSITION AND BURNING CHARACTERISTICS OF WOODThe approximate composition of moisture-free wood is, in even figures:PercentHydrogen 6Carbon 49Oxygen 44Ash 1Total 100This composition corresponds to about C6H1005. Moisture is essentially always associated with wood. Green wood contains approximately 30 to 50 percent moisture; air-dried or seasoned wood contains 15 to 25 percent and kiln-dried about 8 percent. Exposed to the weather, wood absorbs and gives off moisture depending on weather conditions and water contact.""Dry"" wood ignites relatively quickly and readily gives off volatile matter when heated. Long flames and smoke easily occur during burning. The burning action is substantially retarded, however, by appreciable moisture content; ignition is more difficult. When the moisture content is more than about 70 percent, an auxiliary fuel is required to maintain combustion. One of the main factors in the problem of the satisfactory and smokeless combustion of wood is its moisture content."

Sep 1, 1950

By Paul R. Coyle, Anthony T. Iannacchione

A close look at the Loyalhanna Limestone of southwestern Pennsylvania reveals a complex structural environment. Most exposures of the Loyalhanna occur along Chestnut Ridge and LaurelHill within the Allegheny Mountain Section of the Appalachian Plateaus Province. Because the Loyalhanna is rated as a super-pavement aggregate by the Pennsylvania Department of Transportation and because of its proximity to the population centers of southwestern Pennsylvania, the Loyalhanna has been extensively mined along these prominent anticlinal structures. Geologic and engineering analyses were performed using gas well and core logs, outcrop examinations, underground observations, and mine maps. Strata exposures from both outcrops and quarries were used to construct geologic maps, stereo net, and rose diagram projections so that the Loyalhanna’s structural environment could be understood better. Many of these structural conditions cause ground control problems at local quarries. These problems ranged from small-to-moderate sized rock falls associated with roof jointing to pillar failures associated with dipping discontinuities. Stresses ranged from tensional on structural domes where weathering dominates, to high levels of compression within structural saddles. A greater understanding of these characteristics is a prerequisite to develop engineering controls, such as improved mine layouts, pillar sizes, etc., that lessen miner exposure to these hazards.

By R. R. Backer

The Bureau of Mines, in cooperation with Washington Irrigation and Development Co. (WIDCO), evaluated the dewatering of fine coal-refuse slurry using chemicals and various types and combinations of drains in natural earth impoundments. About 40 lb of lime and 2 lb of polymer per ton of dry solids were mixed with the underflow from the preparation-plant thickener. Clear, free water was immediately liberated from the slurry. The percent solids by weight of the slurry increased from about 17 to 30 immediately, and after 5 days increased to 45 wt-pct. This indicates a threefold reduction in total volume after 5 days from 172 cu ft/ton solids originally to 56 cu ft/ton solids.

Jan 1, 1981

By D. A. Hill

This volume contains a summary of the results of past analyses on U.S. Bureau of Mines Contract No. H0122061 which are relevant to electromagnetic location in mine rescue situations. The analytical results indicated that detection of a trapped miner equipped with a special transmitter is feasible in most situations. Location of the miner by surface measurements is also generally feasible within certain errors. The feasibility of miner detection and the accuracy of miner location have been examined theoretically for a wide variety of situations. Agreement with experimental results is generally good in cases where measurements are available.

By R. H. Storch

The work described in this report was part of a Bureau of Mines program to appraise the titanium-mineral resources of Idaho. Part of the program included churn drilling of alluvial deposits that previous preliminary testing, primarily for rare minerals, had indicated to be potential sources of titanium minerals. The first spot churn drilling began in the Deadwood placer area, Valley County, Idaho, in July 1956 to determine both the amount and grade of the ilmenite, FeTi03. Ten holes, ranging in depth from 6 to 40 feet and aggregating 251 feet, were drilled; 54 samples were taken. The samples were sent to the Spokane field laboratory for concentration and visual estimation of the amounts of the more common minerals in the heavy sand concentrates. For specific determinations samples from each drill hole were composited and shipped to the Bureau of Mines laboratory in Albany, Oreg., where petrographic, quantitative X-ray spectrographic, and chemical analyses were made.

Jan 1, 1958

By Isaac A. Zlochower, Michael J. Sapko, Ronald S. Conti

The Bureau of Mines has developed a system using a high-speed electropneumatic mechanism for the rapid (grab) sampling of dusts and gases during an explosion. The sampling system consists of an aluminum housing that incorporates two 30-cm3 preevacuated glass vials with rubber septums. Upon actuation, the sampling probe needle is driven through the septum with a pressurized air pulse, filling the tube with gas and dust from the mine explosion. After a predetermined time, the sampling probe needle is retracted by a second high-pressure air pulse to its normal (quiescent) state, allowing the sampling tube to reseal. The onset and the duration of sampling are independently variable and controlled by a time-delay relay package. This technique enables the monitoring of pyrolysis-charring in coal particles and the generation and combustion of the pyrolysis vapors in both large- and small- scale explosions. The following results were obtained from full-scale dust explosion tests at the Bureau of Mines Lake Lynn Laboratory: (1) Gas sampling of the leading edge of the flame front shows the large concentration changes, characteristic of the flame front; (2) gas samples taken entirely in the flame zone consist of pyrolysis and combustion products with very low residual oxygen; and (3) the particles collected in the flame zone show signs of extensive pyrolysis and charring.

Jan 1, 1988

By E. C. Lane

The motor gasoline that is being marketed in the United States this winter is practically the same 'as that sold a year ago. In fact, there has been little char sin this commodity during the year, as the gasoline sold last summer was almost as volatile as that marketed last winter. Boring the past eight years, the Bureau of Mine's has made semi-annual surveys of the gasoline marketed in the United States, the survey just completed being the fifteenth in the series. The cities in which samples have been collected have been chosen as representative of the more important marketing territories as it is obviously impracticable to obtain a sample of every gasoline sold in the entire country.

Jan 1, 1927

By McHenry Mosier

Mercury is one of the strategic metals the supply of which has been raised from critical uncertainty to more than enough for essential demands. Work by the Bureau of Mines has contributes substantially to increased production of mercury in the United States and to consequent accumulation of Governments stock. Other contributing factors were higher prices for mercury and Government loans to operators. The Bureau has undertaken 15 exploration projects, 13 of which have been completed. This work comprised 40,307 feet of drilling arid 35,082 linear feet of sure ace trenching and has indicated commercial ore containing 37,400 flasks of mercury and marginal ore contain¬ing 29,200 flasks - a total of 66,600 flask , equivalent, respectively, to domestic production at 50,000 flasks per year for 9 months , 7 months, and 16 months. Early in 1944, as Government stocks had become adequate, domestic production was gradually curtailed cancellation of Government contracts for the purchase of mercury and Government control of labor and operating supplies.

Jan 1, 1944

By R. K. Koch

The vapor pressures of liquid columbium and liquid hafnium were deter-mined by the Langmuir free evaporation method as a part of the Bureau of Mines program on the study of transition metals. An electron-beam furnace with a water-cooled copper crucible was used for melting. Temperature was measured with a two-color ratio pyrometer. Least-squares analyses of the vapor pres-sure data gave the following equations: [Logp (atm) = 5 .429 -31,310 T] for liquid columbium in the range 2,740° - 3,140° K, and [Log p (atm) = 5,690 28 T] for liquid zirconium in the range 2,500° -2,810° K. Third-law evaluations of each data set gave mean heats of sublimation (298.15° K) of 175.1±3.2 kcal/mole and 148.3±1.2 kcal/mole for columbium and hafnium, respectively. Second-law standard heats of sublimation determined from sigma plots and from sigma-prime plots agreed fairly well with the third-law values. The sigma-prime plots gave standard entropies of sublimation of 30.96±0.84 eu and 33.S6±0.44 eu for columbium and hafnium, respectively.

Jan 1, 1968

By B. I. Ferber

Toxic and explosive atmospheres are discussed, along with some of the instruments commercially available for their detection. No attempt has been made to evaluate the accuracy of anyone device. This circular has been prepared primarily to aid mine inspectors in selecting suitable instruments for underground gas detection.

Jan 1, 1972

By D. E. Anders

Saturated hydrocarbons from 60 selected samples of a 2,300-foot Green River Formation oil-shale core (Piceance Creek Basin, Colo.) were analyzed by gas-liquid chromatography techniques. Emphasis was placed upon the distribution of normal alkanes and 15 key-branched and cyclic alkanes. The latter compounds consisted of the C15, C16, C18, C19, and C20 chain isoprenoids, the 5-a and 5-ß C27, C28, and C29 steranes, three C30 pentacyclic triterpanes, and perhydro-ß-carotene. The results showed definite evidence of maturation of both the n-alkanes and the branched and cyclic alkanes; however, most if not all of the changes were limited to the indigenous soluble extract and were not the result of additional soluble extract generation from the insoluble kerogen. Source material and environmental variations were important factors in some of the observed differences in the branched plus cyclic alkane compositions.

Jan 1, 1973

By D. E. Hirsch

The Bureau of Mines, as a part of American Petroleum Institute Research Project 60, Characterization of the Heavy Ends of Petroleum, has made extensive use of gel permeation chromatography (GPC). Data developed in this study were used to develop several correlations that greatly expanded the usefulness of GPC and the data have been used as an aid in the interpretation of mass spectra (MS). GPC retention volume data on pure compounds were used with molecular structure to develop correlations that can be used to accurately predict retention volumes, molecular volumes, densities, chain lengths, and ring numbers of many components of petroleum without resorting to further laboratory experimentation. Conversely, the correlation can be used to select or reject some compounds from several possible compounds that are indicated on the basis of MS analysis. The utility of these correlations in compound type characterization is demonstrated by showing their application to 330° to 550° C fractions from a low-sulfur and a high-sulfur crude oil.

Jan 1, 1974

By Kenneth J. Miner

Pittsburgh bed and Lower Freeport bed coals were tested in the U.S. Bureau of Mines two-stage froth flotation pilot plant, which utilizes a new flotation process to remove pyritic sulfur. The process consists of a first-stage coal flotation step to remove coarse, free pyrite and other refuse in the tailings. The clean coal froth concentrate is then repulped and treated with a coal depressant, a pyrite collector, and a frother to selectively float the remaining pyrite in a second stage. Results in the pilot plant were excellent, comparing well with those obtained in laboratory batch tests. That is, about 70 percent of the pyrite present in the Pittsburgh bed coal and about 90 percent of the pyrite present in the Lower Freeport bed coal were removed with excellent final clean coal recoveries.

Jan 1, 1973

By Robert F. Chaiken

More than 500 fires are now burning in abandoned coal waste banks and coal deposits in the United States. Once established, such fires can burn for decades, and extinguishing them by conventional methods such as surface sealing to exclude air, excavation to remove fuel, or flushing to cool the fire zone is usually difficult and always expensive. Burnout Control, a technique developed by the Bureau of Mines for the control of abandoned coal fires, involves the accelerated combustion of coal in place with total management of the heat and fumes produced. A burning waste bank or mine is placed under negative pressure relative to the atmosphere, and heat and combustion products are drawn from the combustion zone through an exhaust ventilation system. Heat produced appears as sensible heat in the exhaust, at temperatures as high as 1,000° C (1,832° F), and could be recovered for the production of steam, hot water, process heat, or electricity. The Bureau's first field demonstration of Burnout Control was at Calamity Hollow in Allegheny County, PA (near Pittsburgh). Calamity Hollow was the site of an underground mine in the. 1900's and was surface mined in the 1940's. In the winter of 1961~62, a fire of undetermined origin was discovered in the exposed coal. In 1963, the Bureau constructed a trench barrier around the fire and a surface seal over the affected area. The fire was isolated but, not completely extinguished. In 1979, when the Bureau began work on the Calamity Hollow Mine Fire Project to demonstrate controlled burnout, the fire was still smoldering on the hot side of the trench barrier. The project, which was begun in December 1979 and ended in July 1982, consisted of the design, construction, operation, and subsequent dismantling of a Burnout Control ventilation system. This report, although considered part 2, is actually the last of a five-part series that describes the Calamity Hollow Mine Fire Project. It was written last because it involved the analysis of a substantial body of data describing in detail the results of a continuous 4-month burnout operation. The first report, part 1, describes the design and construction of the field installation. Part 3 describes the instrumentation used to control and monitor the progress of the burnout operation. Parts 4 and 5 deal with the closeout phase of the field demonstration. Part 4 describes the procedure used to quench the fire, and part 5 describes the final excavation and backfilling of the heated zones. The reports in this series document the Calamity Hollow controlled burnout demonstration, which showed that (1) controlled in situ combustion is a feasible method for controlling underground fires in abandoned mines, (2) the resultant thermal exhaust output is suffIcient for energy utilization, and (3) water injection-fume exhaustion is a potentially effective method for cooling large underground fire zones. Further investigations of both Burnout Control and the water injection-fume exhaustion quenching procedure are planned.

Jan 1, 1989

By I. D. Shah

The copper-nickel ore of the Duluth Gabbro Complex in northeastern Minnesota is a large potential domestic resource of cobalt and platinum-group metals. However, because of the low grade of the primary metal values (0.5 pct Cu, 0.15 pct Ni), the private sector has assigned a relatively low priority to the development of technology for processing this ore, anticipating that mining probably would not begin until the mid-1990's. Furthermore, preliminary processing flowsheets considered by the mining companies centered on the primary metal values. As part of an effort to help provide the basis for technology to recover critical and strategic minerals from domestic resources the Bureau of Mines is investigating methods to recover all of the mineral values, in the Duluth Gabbro material, with particular attention to the byproduct critical minerals. A key step in this process is the removal of a relatively large amount of iron present in the bulk sulfide flotation concentrate to permit subsequent extraction of mineral values. This report describes a direct smelting method that removes most of the iron and produces a copper-nickel-cobalt matte, an intermediate product from which the metal values subsequently are separated. Copper, nickel, and cobalt grade and recovery data are presented for the direct smelting method. Test results showed that under certain conditions some of the mineral values reported to the slag, requiring slag cleaning to recover them.

Jan 1, 1983

By K. Robert Dorman

This Bureau of Mines report describes laboratory and field experimentation in building mine ventilation stoppings, air-door frames, and fan bulkheads with a civil construction technique. Shotcrete is applied to a free-standing, three-dimensional wire-truss panel, which is easily cut and rapidly erected. In mines where shotcrete equipment is available, this technique should be faster and cheaper than conventional block-and-mortar or monolithic concrete construction.

Jan 1, 1980

By Fred C. Turin, William J. Wiehagen

This study examined musculoskeletal injury risk at four mining sites: underground coal, underground limestone, surface copper, and surface phosphate. Each site offered opportunities to investigate musculoskeletal disorder (MSD) injury risks and how those risks might be identified and categorized. The National Institute for Occupational Safety and Health (NIOSH) worked with these sites to (1) identify work activities that showed evidence of MSD injury risk, (2) examine physical risk factors that can lead to MSDs for a handful of work tasks at each site, and (3) develop a set of ideas for problem-solving to help reduce risk factors for examined work tasks. For each site, NIOSH implemented a plan that was refined over the time period of this study. The plan consisted of four steps. The first step was to use mine injury records, a musculoskeletal discomfort questionnaire, front-line supervisor interviews, and a list of management concerns to identify work groups and work activities that have significant evidence of MSD risk factors. The second step was to select work tasks for evaluation. The third step was to interview those who do the work and make observations to characterize the MSD risk factors and musculoskeletal symptoms that exist for target tasks. The final step was to conduct brainstorming sessions with workers who perform the work or have a stake in the production task. The brainstorming sessions served to identify general strategies (ideas) for reducing MSD risk factor exposures. A final report of findings was presented to mine management and workforce representatives at each site. The risk factors and ideas for improvement identified for each site were specific to the target tasks examined. These target tasks were diverse, but there were some key similarities. For instance, jobs were found at each site that required a significant amount of manual work involving the upper extremities and low back. Handling heavy and awkward objects, forceful arm and shoulder exertions, and working in awkward postures were common for a variety of jobs across the four sites.

Jan 8, 2004

By B. Dimitriades

Data on smog-forming reactivities of exhaust aldehydes are scarce. Such data were obtained by irradiating in a smog chamber typical exhaust aldehydes, individually and in exhaustlike mixtures. Observed reactivity manifestations were rate of nitrogen dioxide formation (RNO2) and yields of oxidant, peroxyacetyl nitrate, and formaldehyde. Results showed that exhaust aldehydes vary widely in reactivity. Formaldehyde showed high RNO2 reactivity but low oxidant yield; benzaldehyde, [m]-, and [p]-tolualdehyde were totally unreactive when irradiated individually; [o]-tolualdehyde was reactive. In mixtures, benzaldehyde manifested reactivity in terms of peroxybenzoyl nitrate yield. Exhaust aldehydes as a group are judged to be as reactive as the exhaust olefin group. The importance of the aldehyde contribution to exhaust reactivity and methods for assessing such contribution are discussed.

Jan 1, 1971

By G. M. Potter, F. S. Wartman, M. D. Schmid

"In matte smelting of copper it has been established that the sulphpr present will combine with copper as long as the latter is present, and that thereafter it will combine with iron. The Cu-Fe ratio in the matte is determined by the Cu-S ratio, presumably owing to the much greater affinity of copper for sulphur or, expressed thermodynamically, the greater stability of copper sulphide in contact with silicate slag. Now, the work of Fournet and of Schütz, which is quoted in many elementary metallurgical texts, indicates that manganese ranks ahead of copper in its affinity for sulphur. Hence, we might expect that manganese could be concentrated from its admixture with iron. Compounds by matte smelting, and Rotts / has patented such a process. This greater affinity of manganese or sulphur is used to advantage in iron metallurgy, also, in which it is well-known that sulphur will combine with manganese and separate from metallic iron as manganese sulphide. Manganese sulphide,however, is quite soluble in silicate slags. 5/ The loss of manganese in slag in any attempted matte smelting is therefore great.If this solubility of manganese sulphide is slag is a physical one and the reaction MnO + FeS MnS + FeOIs substantially complete, then it might be expected that the addition of copper sulphide, which is almost entirety insoluble in slag, would serve to extract the manganese sulphide with the formation of a manganese-copper matte on the other hand, if an equilibrium exists in the above reaction, a copper sulphide layer would displace that equilibrium in one direction or the other, according to whether iron sulphide or manganese sulphide were more soluble in the matter layer."

May 1, 1937