Search Documents

By R. Hogg

"Particles play an important role in our environment and in many aspects of human activity. Much of the Earth's surface - sand, soil, rocks - consists of particles, as do clouds in the atmosphere, smoke from fires, and dust in our homes. Many of the foods we eat - cereals, flour, instant coffee - and everyday items such as pharmaceuticals, cosmetics, detergents and other cleaning products are encountered in the form of particles. Inks and paints consist of very fine particles dispersed in liquids. Modem agriculture uses huge quantities of fertilizers and pesticides, largely in particulate form. The list could be extended almost indefinitely; particle systems are obviously an important part of our daily lives. But what do we know about them? For most people, the answer is probably: not much.We are all familiar with the three common states of matter: gas, liquid and solid. In many respects, particle systems should be regarded as a distinct class of their own. The particles themselves may be solid but we all know that a heap of sand is quite different from a solid rock. A cloud of liquid droplets - fog - has much more in common with a cloud of solid particles - smoke - than it does with a bucket of water. There are certain characteristics and properties which are unique to the particulate state. The behavior of any particle system is determined not only by the material from which the particles are made, but also by interactions among the particles and with their environment. These interactions become increasingly important as the size of the particles decreases, and for exceedingly fine particles, smaller than about one micrometer (0.000001 meters or 0.00004 inches), these interactions dominate and we enter the realm of colloidal systems.Particle SystemsA system in which discrete entities - particles -are dispersed in a continuous medium can be regarded as a particulate system. The particles and the medium can consist of a solid, liquid or gas. The various combinations and some common examples are listed in Table 1. The properties and behavior of these systems depend on the characteristics of the particles, the nature of the medium, and the relative abundance of the two phases. In general, it is the latter which determines the kind of behavior exhibited by the system.As a general rule, the behavior of particle systems follows that of the dispersed phase (the particles) at high concentration, and that of the continuous phase (the medium) at low concentration. For example, both powders and smokes consist of solid particles in a gaseous medium. However, in a powder the solids typically occupy over one half of the total volume; in many respects powders behave like solids. In a smoke, on the other hand, the particles may take up only a few parts per million of volume, so that these systems generally behave like gases."

Jan 1, 1989

By Richard Havens

A flotation procedure was devised by the Federal Bureau of Mines for beneficiating Mount Wheeler, Nev., beryllium ores that contain the beryllium minerals bertrandite and phenacite in a complex association with calcite, fluorspar, mica, quartz, and other accessory minerals, The method also has proven to be effective in trials on ore from the Lake George, Colo., area. Samples used in most of the research ranged from 0.49 to 0.73 percent BeO. Beryllium mineralization varied from two-thirds bertrandite to all phenacite. An unusually high grade sample containing 5 percent BeO as phenacite was floated on a batch basis to prepare concentrate for utilization studies. The beryllium minerals were floated from undeslimed pulps at natural pH using sodium fluoride and sodium hexametaphosphate (HMP), as modifiers, and a fatty acid-fuel oil combination as the collector. Key factors were the use of a minimum of about 4 pounds of sodium fluoride and between 2 and 4 pounds of HMP per ton of ore. Efficacy of the HMP was related to the grind, mineralogical composition, corollary reagents, and type and time of conditioning. Addition of the fluoride, HMP, and collector in that order, followed by appropriate conditioning after each addition, was essential for satisfactory flotation.

Jan 1, 1961

By C. M. McCulloch

The methane content of virgin bituminous coalbed can now be measured accurately in the field with exploration core samples from vertical boreholes. The gas content of the coal per unit weight can be used either to design a mine ventilation system or to determine if degasification of the coalbed will be necessary before mining, and to determine the gas resources in the coalbed. The equipment necessary to conduct the test costs less than $50. The gas con-tent of the coal in place in the ground is determined by summing the gas lost from coring, gas measured during desorption, and the residual gas in the coal. Upon removal from the borehole, the core sample is placed in an airtight container and des orbed for several weeks until the desorption rate is below 0.05 cm3/g for 5 consecutive days. The gas lost from the core while it was being cored and the residual gas are estimated by a new graphical method. The amount of gas remaining depends upon whether the coal is friable or blocky. Friability appears to relate to the depth of the sample below the surface, fixed carbon percentage, Hardgrove grindability index, and proximity to tectonic disturbance. Friable coals emit nearly 96 pct of the total gas during desorption whereas a blocky coal emits only 60 pct of its total gas. Coalbeds that are ill defined as to their blocky or friable nature must be tested in the laboratory for unambiguous analysis.

Jan 1, 1975

By Kenneth M. Earl

In its investigation of deposits of strategic minerals, the Bureau of Mines did some development drilling at the New Galena Deposit in an endeavor to find an additional source of supply of lead. In Bucks County, lead and zinc minerals have been found in shales over a largo area west and northwest of Doylestown. Considerable mining has been done in the vicinity of New Galena on the North Branch of Noshaminy Creek, 3 miles northwest of Doylestown. It has not been possible to obtain a satisfactory history of the New Galena mine, as there is much disagreement in statements. Most of the mining was done in open pits. Two shafts were sunk to shallow depth; one of these became part of the main pit' which is 256 foot long, 50 to 75 feet wide, and 20 to 44 feet deep. Small pits 8 to 10 foot square wore sunk on the ore zone, which extends some 1450 feet to the southwest. The rock containing the minerals is either black or gray shale. The gray material closely resembles limestone. The following minerals have been reported from the mine: quartz, ankerite, calcite, galena, sphalerite, pyrite, chalcopyrite, and bornite. Some of the galena has yielded 10 to 15 ounces of silver and 10 cents in gold per ton. The average grade of the ore as mined is not known. To investigate the downward extension of the ore shoot, the Bureau drilled two holes aggregating 373.9 feet, No additional ore was developed by this work.

Jan 1, 1950

By Robert H. Merrill

Measurement of the deformation of a borehole in rock subjected to a change in applied stress can be used to calculate the magnitude and direction of the applied stress, provided a satisfactory deformation-applied stress relationship exists , In this investigation by the Bureau of Mines the deformation of a bore- hole in a rock model subjected to a known applied stress was compared with the theoretical deformation of a hole in an elastic, isotropic plate and was found to be in good agreement. Hence, this relationship can be used to calculate the applied stress on a borehole from borehole deformation measurements.

Jan 1, 1961

By Lee M. Manna

Approximately 10,000, 10-Ton, 4 wheel, 2 truck, coal mine cars are in general service in U. S. Mines. None are equipped with an automatic braking system. Very few are equipped with hand or parking brakes. The report lists major manufacturers of the car and develops estimate as the percentage represented. It complies physical specification of cars of major car manufacturers, and develops a composite clearance diagram. It then discusses a pneumatic system employing truck components for an automatic system that could be used as an add-on unit. The components are listed and priced and a schematic circuit is developed for the system. Recommendations as to future programming are made.

Jan 1, 1976

By Helen W. Lang

This report describes a monitoring system applied by the Bureau of Mines to provide rapid, continuous determination of the main constituents of exhaust gas during the Bureau's approval schedule testing of diesel engines for under-ground use. Commercially available continuous analyzers with strip chart readout are employed for nitric oxide (mass spectrometric), carbon dioxide (nondispersive infrared), methane (NDIR), carbon monoxide (NDIR), and oxygen (polarographic). Good correlation is obtained between the continuous instrumental results and those obtained by batch chemical and gas chromatographic methods.

Jan 1, 1969

By Oliver Q. Leone

Three electrorefining cells were designed to investigate various factors associated with the electrorefining of reject - grade titanium sponge . Operation of the cells provided information on cell design as well as on how design and operating variables affected the quality of the titanium product . A sodium chloride - titanium chloride electrolyte was used , and the electrolyte chambers had capacities ranging from 400 to 3,500 pounds of molten salt . Major factors investigated were electrolyte composition , temperature and useful life , effect of various cathode shapes and materials of construction , methods for removing cathode deposits , effect of current density and cell potential , and the mechanics of deposit growth and crystal morphology . One of the cells was in intermittent operation over a 4 - year period and produced 2 tons of refined titanium . A product with a hardness of 80 or less Bhn (Brinell hardness number ) was consistently and easily obtained . Some metal with a hardness of less than 60 Bhn was produced . In one of the cells in which the electrolyte was held at operating temperature with an internal heater an ac input of 25 kw maintained 3,500 pounds of electrolyte at 850 ° C , but with an external heater 35 kw was required to maintain 400 pounds at 850° C.

Jan 1, 1964

By G. R. Hopkins

"The average heat requirement per barrel of crude refined in the United States rose from 579,000 B. t. u. in 1940 to 584,000 B. t. u. in 1941. This marked the second successive year in which there was an apparent loss in fuel efficiency at refineries. This ""loss"" took place despite an increase in crude runs, which used to be an invariable indicator of a lower average.Probably the chief factor in the increased heat requirement in 1941 was the gain in the over-all gasoline yield from 43.1 percent in 1940 to 44.2 percent in 1941. Possibly another important factor was the further use of obsolete equipment to increase throughput.The refiners used more of all kinds of fuel excapt coke in 1941 than in 1940. However, the only fuels which increased materially in relative importance were refinery gas, which contributed 51.6 percent of the total heat units in 1941 compared with 50.7 percent in 1940, and natural gas, the share of which rose from 17.1 percent in 1940 to 18.0 percent in 1941. The changes in the percentages for the other fuels were as follows: Oil decreased from 25.7 to 24.1 percent; acid sludge fell from 2.7 to 2.5; coal remained at 3.4 percent; and coke (including steam) fell from 0.5 to 0.4 percent.New records for fuel efficiency were set in all three of the districts east of the Mississippi, namely, East Coast, Appalachian, and Indiana, Illi¬nois, etc. All the ether districts reported higher average fuel requirements in 1941, except the Louisiana Gulf and Arkansas-Louisiana inland.Since the year of the first statistics, the refiners have steadily increased their purchases of electricity. In 1941 total purchases were 1,862,996,000 kilowatt-hours, or 11 percent more than in 1940."

Apr 1, 1943

By E. G. King

Many of the rare-earth oxides are now commercially available in pure form and they have a variety of potential technical uses. Thermodynamic data for these oxides, however, are rather sparse. It is one of the functions of the Bureau of Mines to fill the need for this type of information. This report gives the results of low-temperature heat-capacity and high-temperature heat-content measurements by the Bureau of Mines of lanthanum sesquioxide. The entropy at 298.15° K. was evaluated and heat-content and entropy increments above 298.15° K. were obtained to 1,800° K. The results were combined with the known heat of formation at 298.15° K. to derive heats and free energies of formation at higher temperatures. Sufficient information is now available to permit reliable thermodynamic calculations involving lanthanum sesquioxide within the temperature range 298° to 2,000° K.

Jan 1, 1961

By P. J. Colbassani

Samples of mine atmospheres collected by Federal coal-mine inspectors during their inspections and investigations of coal mines, in accordance with provisions of the Federal Coal Mine Safety Act (66 Stat. 692; 30 U. S. C., sees. 451-483) are analyzed routinely by chemical methods at Bureau of Mines laboratories. When samples collected in open workings of nongassy coal mines at points not less than 12 inches from the roof, face, or rib contain 0.25 percent or more methane, the act requires the operator, during operation of such mine, to comply with the provisions of sec. 209, Title II, of the act, which pertain to gassy mines. The methane con-tents of such samples are determined by a physical method based on infrared absorption spectrometry to provide an independent check on analytical results obtained by chemical methods. This information circular describes the equipment and procedures used by the Bureau for determining low concentrations of methane in coal mine atmospheres by infrared absorption spectrometry. ACKNOWLEDGMENTS The authors are indebted to Dr. R. A. Friedel, Chief of Spectrometric Section, Branch of Coal-to-Oil Research, Bureau of Mines, for suggesting the analytical method and for furnishing valuable advice and assistance, and to J. A. Queiser of his staff for making exploratory measurements by this method; to Dr. M. G. Zabetakis of the Division of Explosives Technology for his assistance during the conduct of preliminary experimentation; and to L. B. Berger, Chief, Branch of Health Research, under whose guidance the equipment was procured and the work conducted.

Jan 1, 1958

By Spencee L. Willett

In 1986, at the request of the Bureau of Land Management, the U.S. Bureau of Mines studied a 51, 160-acre portion of the 107,920-acre Diablo Mountain Wilderness Study Area (OR-001-058) in order to evaluate its mineral resources. The study area is located 1n Lake County, OR, about 45 miles northwest from Lakeview. The study area is located near the northwest corner of the Basin and Range physiographic province. Tertiary Picture Rock basalt with tuff interbeds underlies the area (Travis, 1983). No mineral resources were identified; no mines, prospects, claims, or mineralized areas exist in or adjacent to the Diablo Mountain study area.

Jan 1, 1987

By Phillip Allender, Wolf Karo, Knox Van Dyke, Lixin Wu, Ali Ardekani, Jorge Garcia, Jaime Gutierrez

"We report that two different micropolystyrene round beads linked to either luminol or lucigenin have been developed. The 1-µ.m-diameter beads arc useful reagents that allow one to perform chemiluminescent (light producing) phagoeytic reactions without opsonization. It is known that luminol reacts with peroxidases (e.g., myeloperoxidase) while lucigenin reacts mainly with superoxide anion. Luminol and lucigenin beads produce cellular chemiluminescence (CL) with neutrophils, macrophages, monocytes, and differentiated human promyelocytic leukemic cells (HL60). When myeloperoxidase (MPO) is present luminol beads evoke higher CL from neutrophils, but when little or no MPO is present, lucigenin beads produce higher amounts of light. Lucigenin beads appear to be active inside these cells where unbound lucigenin does not enter freely.INTRODUCTIONA variety of cells, e.g., neutrophils (Ns) and macrophages (Ms), can engulf foreign particles (1). This engulfing or phagocytic activity is used by the body to kill bacteria and to eliminate foreign particles such as respirable dusts, e.g., coal, silica, or cotton. The neutrophil engulfs or phagocytizes bacteria which are coated with plasma antibodies and/or complement proteins (Fig. 1). The coating or opsonization allows the neutrophil to recognize foreign substances. Usually the absence of opsonization prevents the cell's recognition of a foreign particle and the particle is not phagocytized. Macrophages, particularly the alveolar Oung) cells, do not require opsonization for phagocytosis. Ms should not be selective toward individual dusts because they serve a major role in eliminating a variety of these.Particle size can also be a factor. Usually a particle with a diameter of 0.5-5 µ.m is considered in the respirable range. Larger particles are trapped before they reach the alveoli Oung spaces where oxygen exchange with blood occurs), ·and smaller particles do not generally settle, and are not engulfed by macrophages (2). Tabato and Ikada (3) found that maximal phagocytosis of microspheres takes place when their diameter is in the range of 1.0 to 2.0 µ.m. In addition, they found that beads with hydrophobic surfaces were more readily phagocytized than hydrophilic surfaces."

Jan 1, 1990

By D. J. MacDonald

This U.S. Bureau of Mines report reviews published information on synthetic berlinite (AlP04) and suggests experimental conditions requisite for its production. Berlinite is a piezoelectric material with potential use as a substitute for quartz in the crystal oscillators, which are components of electronic and electroacoustic equipment. Information gathered here (mostly from published sources) includes historical background, physical properties, end-use applications, criteria of quality, and physio-chemical factors involved in berlinite crystal growth. It is concluded that growing large high-quality berlinite crystal would require high-purity starting materials in an autoclave equipped with a noncorrodible liner and operated with temperature control of ±O.OO5 ac over a range of 250 to 350 ac.

Jan 1, 1995

By Steven W. Schmauch

The Ruby Mountains study area encompasses 75,615 acres managed by the U.S. Bureau of Land Management in Madison County, MT. A mineral survey was conducted by the U.S. Bureau of Mines and U.S. Geological Survey in 1984. Bureau of Mines personnel reviewed literature and county mining records, and examined prospects or mineralized areas to determine mineral resources. Geological Survey personnel evaluated the area by geochemical sampling and geophysical surveys. There are no organized mining districts and no current claims in the study area. Significantly mineralized quartz veins, shear zones, or talc bodies apparently do not exist within the study area. A small part of the Kelly Iron Deposit is inside, but dips away from the study area; the main occurrence is estimated to have 32 million tons of subeconomic resources that average 21 percent iron.

Jan 1, 1985

By M. J. Ferrante

The standard enthalpy of formation, low-temperature heat capacities, and enthalpy increments above 298 K were determined by the Federal Bureau of Mines for synthetic dawsonite [NaA1C03(OH)21. The enthalpy of formation was determined by hydrochloric acid solution calorimetry, with the result ?Hf°298 = -469.4±0.7 kcal/mole. The low-temperature heat capacities were determined from 6 to 307 K by adiabatic calorimetry. Tabulated are low-temperature values of Cp°, S°, and H.-Ho° from 3 to 298 K. The derived entropy at 298 K is S298 = 31.55±0.3 cal/deg mole. Enthalpy increments above 298 K were obtained by copper-block drop calorimetry. Tabular data of Cp°, S°, H°-H°298, -(G°-H°298)/T, ?Hf°, ?Gf°, and log Kf are given from 298 to 477 K. Enthalpies and Gibbs energies of decomposition are also reported.

Jan 1, 1976

By Robert A. Jankowski

"Following passage of the Coal Mine Health and Safety Act of 1969 (Public Law 911173), the Bureau of Mines initiated a research program aimed at controlling respirable dust exposures of coal mine workers. Respirable dust is the dust that gets into, and interacts with, the lungs of those who inhale it. It has long been recognized as a severe health hazard to mine workers. This program has been implemented by a team effort consisting of the Bureau's in-house capabilities, the Generic Center for Respirable Dust, and contractors, as necessary. Over the years, Bureau research has addressed principally three areas:o Compliance with the Federal 2.0 mg/m3 dust standard (1970-76).o Dust control for longwall mining (1976-1983).o More stringent respirable dust standards due to quartz dust (1983-1987).In addition, fundamental studies have been conducted by the Generic Center for Respirable Dust, with emphasis on penetration of dust into the lung. Accomplishments have been significant, but problems remain, as noted later.The Coal Mine Health and Safety Act of 1969, established a 2.0 mg/m3 dust standard for all coal mining operations, underground as well as surface. At the time of enactment of this legislation, the industry was averaging approximately 4.0 mg/m3. The Bureau of Mines respirable dust research program played a significant role in identifying and developing effective technology to allow better compliance with this new standard, thanks to industry implementation and Federal enforcement."

Nov 1, 1988

By George A. Morgan

The production and processing of crude petroleum and natural gas are the dominant economic sectors of the Middle East. Development of downstream petrochemical and fertilizer industries continues as a major investment area. In 1993, the 15 countries that constituted the region accounted for 29 % of world crude petroleum output, 19 % of world natural gas plant liquid production, and 6 % of world dry natural gas production. Only Cyprus and Lebanon were not crude petroleum producers. Regional output was up for most major mineral commodities. A major exception was phosphate rock, which declined sharply owing to reduced worldwide demand. Total crude petroleum output declined by over 100 Mbbls, again owing to slack demand in the major industrial countries.

Jan 1, 1995

By A. F. Colombo, D. W. Frommer

Bench- scale tests were made to determine the applicability of flotation as a means of upgrading finished and semifinished magnetic concentrates prepared from reductively roasted iron ores . Both anionic and cationic flotation methods were used to remove siliceous gangue from the magnetic concentrates and produce upgraded products . Seven magnetic concentrates , containing from 6.7 to 13.7 percent SiO2 , were improved by the flotation treatment , yielding final concentrates containing less than 6.0 percent Si02 . Cationic flotation methods were studied on four of the seven samples ; of this group only one sample yielded better results by cationic flotation than by the anionic method .

Jan 1, 1964

By Will H. Coghill, G. Dale Cole

"INTRODUCTION This paper describes a method for the rational sorting of particles by means of a laboratory batch jig. Its purpose is to show that a material can be reliably appraised for gravity concentration without the drudgery of sink-float fractionations.Development of the batch- jig method of testing was incidental to a study of the Birmingham, Ala., red-iron ores now being conducted by the Bureau of Mines in cooperation with the University of Alabama and the ore-producing companies.APPLICATIONOres and coal are commonly tested for their gravity-concentration characteristics by specific-gravity dissections in heavy liquids. The heavy liquid most commonly used for coal is zinc chloride and for ores they are benzene, carbon tetrachloride, acetylene tetrabromide, methylene iodide, and thallium malonate formate. The last is poisonous and corrosive to the skin but is essential for separations in the 3.3 to 4.4 specific gravity range. The last two of these liquids are expensive, and several of them are hard to obtain now.Although it is not suggested that heavy-liquid dissections be eliminated entirely, sometimes a more reliable evaluation of coal and ore can be obtained by other and more simple means. For example, sink-float data were unsatisfactory as a guide to commercial gravity concentration of a red-iron ore because they did not take into account the difference in particle shape of the hematite and gangue and the differences in true and apparent specific gravity of the hematite grains, some of which were porous. For this ore, the batch-jig method of testing herein discussed proved advantageous. Not Only did the batch-jig data give a truer picture of the concentration problem, but only about one-tenth the time of the conventional sink-float tests was required."

Jul 1, 1944