Search Documents

By G. L. Humphrey

Although silicon carbide has been an important manufacture refractory for many years, knowledge of its thermodynamic values has been seriously lacking. In fact, some of the very properties that make it a useful substance, particularly chemical inertness, obstruct determination of its heats of formation and reaction. This paper reports the results of new measurements of the heats of combustion and formation, low-temperature heat capacity, entropy at 298.16°K., and heat-content and entropy increments between 298° and l,800°K. Two varieties of silicon carbide were studied -the common, hexagonal (type II) and cubic. The data are combined to obtain heat and free-energy-of-formation functions, which are given in tabular form. It is shown that the cubic variety is the more stable at temperatures to at least 1,800°K but, because of the inherent difficulties and errors in the heat-of-formation determinations at 298°K, it was not found possible to specify the free-energy difference accurately. The mechanism of silicon carbide formation from silica and carbon is not known and is not ascertainable from thermodynamic data. It appears improbable, however, that it can be a single-step reaction. Some reactions involving silicon monoxide gas and metallic Silicon, as possible intermediates in silicon carbide formation, are considered and shown to be thermodynamically feasible.

Jan 1, 1952

By Lloyd Williams, H. K. Gibbs, William L. Crentz, J. W. Miller

"Reserves This investigation shows that the Poplar Creek is the most important bed in Scott County from a production standpoint. Although the Poplar Creek bed contains the largest reserve, the Big Mary has a larger recoverable reserve. Estimates of reserves also have been made for the Pewee, Red Ash, Windrock, Upper Pioneer, Jellico, and White Oak beds.Known measured and indicated reserves of coal, based on a minimum bed thickness of 14 inches and on 1,800 short tons per acre-foot of coal in place, are estimated to be 143 million tons as of January 1, 1954. Of this total, 74 million tons is in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics are too meager for making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.Recoverable reserves of coal are estimated in beds 28 inches and more thick. This thickness is about the minimum now being mined by hand loading onto conveyors in the Appalachian region. The weighted average recovery for all beds in Scott County, as determined by this investigation, is 52.4 percent. This percentage is based on the total thickness of coal in the bed (less partings three-eighths inch or more thick) rather than on the thickness of the coal mined. Based on the weighted average percentage of recovery for all beds in Scott County, the recoverable reserves of coal are estimated to be 39 million tons as of January 1, 1954.Coal Analyses Chemical analyses of coal samples taken for this study show that the coal in Scott County is of high-volatile a bituminous rank except the Upper Pioneer bed, which is shown to be high-volatile B bituminous. The Pewee bed shows typical low-sulfur characteristics. The high ash and sulfur in the Big Mary are characteristic of that bed. The Poplar Creek is moderately low in ash and sulfur in areas where there is no parting in the bed."

Jun 1, 1956

By Richard W. Knostman

A study was made of the factors affecting lead and zinc production in the Pacific Northwest. Costs, ore reserves and potential resources, and domestic demand were analyzed. It was concluded that a projected 3.1-percent average annual increase in U.S. demand for zinc through 1975 and a corresponding 2.5-percent rise for lead will be supplied mainly from mines in the Eastern and Central States. Annual Pacific Northwest mine production of lead is estimated to fluctuate around 82,000 tons, while zinc output may average 135,000 tons through 1975. Measured, indicated, and inferred reserves in the Pacific Northwest, containing 1.56 million tons of lead and 2.59 million tons of zinc, are more than sufficient to maintain this level of production. Annual production from Pacific Northwest electrolytic zinc plants is expected to increase to over 300,000 tons of slab zinc by 1975. Lead smelters may experience difficulty in maintaining output at 1964 levels.

Jan 1, 1967

By John H. Soule

The Royal John mine was examined in November 1942 by a mining engineer of the Bureau of Mines, who proposed development of the Royal John and other properties in the area. Geologists of the U. S. Geological Survey studied the area in 1943 and 1944 and made definite recommendations. Also, in 1943 the Peru Miring Co. mapped the Royal John and did considerable diamond drilling. The Bureau of Mines started the Royal John portion of a project pertaining to the general district in April 1944. This project was completed in Juno 1945. The work, consisting of diamond drilling, was supervised by Robert O. Hill, mining engineer, and the results were published in Report of investigations 3904, Exploration of Grey Eagle, Grandview and Royal John Claims, Grant County, N. WIC. In 1947 and 1948 the Royal John was re-examined by a Bureau engineer, and additional development to increase the reserves of low-grade lead-zinc ore was proposed. This project was started in August 1948 and completed in Juno 1949.

Jan 1, 1950

By R. P. Vinson

The Bureau of Mines conducted a series of tests to determine how well the Bendix BDX 60, the Gilian HFS 113U, the MSA Fixt-Flo, and the Spectrex PAS-3000 dust sampling pumps control the flow rate at 2 L/min. These tests were performed because users need to know the performance characteristics of sampling pumps to select the pump that best satisfies their sampling requirements. Long-term (6- to 8-h) flow stability at various backpressures was examined in relation to the flow control tolerance of ±5% of the flow, the level imposed by Federal regulations; four of the five Bendix pumps did not meet the criterion for this test, which was passed by all other pumps tested. Flow control recovery times were measured at transient backpressures; all pumps evaluated met the criterion for this test. The low-flow indicators of the sampling pumps were tested; only two Bendix pumps and one Gilian pump met the criterion of indicating a flow change greater than ±5%. In the pulsation flow measurement test all of the pumps passed, with pulsating flows greater than 20 Hz. The Bureau also evaluated the manuals accompanying the sampling pumps. All were judged adequate except the Spectrex manual, which was judged poor.

Jan 1, 1985

By D. W. Butner

As a part of the Bureau of Mines program for the discovery and development of critical and essential mineral deposits, the Darwin district, Inyo County, Calif., was chosen for investigation as a possible source of, tungsten ore. Two properties were active in the district at the time. One was producing tungsten concentrate and the other was preparing to produce tungsten concentrate as a byproduct in the milling of lead-zinc ore. The objective of the project set up by the Bureau was to investigate promising areas and to sample, thoroughly those which preliminary inspection indicated contained tungsten ore. Work was begun November 17) 1941, and completed January 19, 1942. In the course of the project, 18 localities were inspected and 9 were sampled. The following pages brief the history, note the location, and outline the physical features and geology of the district. The work performed by the Bureau of Mines is described and supplemented with assay maps.

Jan 1, 1949

By Harold B. Ewoldt

The Appalachian Ores Co., Sweetsprings, W. Va. was a small but persistent producer of manganese ore for several years prior to 1942. Most of the ore mined was hard, nodular psilomelane, with some pyrolusite and, wad, occurring in clay. The Bureau of Mines started an investigation of the area in January 1942 and completed the work in May 1942. Twenty-four churn-drill holes were bored, aggregating 2,084 feet. A total of 420 feet of test pits was sunk on selected drill holes to check the churn-drill sampling. Twelve drifts and crosscuts aggregating 139 feet were driven from the bottom of test pits to investigate concentrations of manganese nodules. Three hundred sixty-six churn-drill samples and 102 other samples were sent to Bureau laboratories for analyses. Beneficiation tests were conducted in the Burp.au of Mines laboratory in Rolla, Mo. Results of testing 10 samples indicated that approximately 80 percent of the material in crude ore could be discarded by log washing. Gravity tests indicated 'that 55 percent of the total manganese in the crude ore was recoverable as a gravity concentrate averaging 34.6 percent manganese.

Jan 1, 1949

By G. W. Birge

Twenty-eight samples, representing the Pittsburgh, Lower Kittanning, Stockton-Lewiston, Coalburg, Winifrede, Cedar Grove, Peerless, No. 2 Gas, Powellton, and Eagle beds, were carbonized by the Bureau of Mines--American Gas Association (BM-AGA) method, and yields of products and physical properties of cokes were determined. Expanding characteristics of 22 of the samples were determined in the Bureau of Mines sole-heated oven. The Kanawha County coals tested were high-volatile A bituminous in rank, with dry, mineral-matter- free fixed- carbon contents ranging from 53.9 to 66.3 percent. With few exceptions, they were chemically satisfactory for metallurgical use, and most of the coke-strength indexes were within the industrially accepted range for high-volatile blending coals.

Jan 1, 1963

By M. Didyk

In this report, the application of the PHU/MVS program is demonstrated through the use of a simple but realistic mine ventilation program. The report details, the problem description, the input data required and the various output features of the simulator. The PSU/MVS program is written in Fortran IV for use with IBM 370/168 computers. A version of the program that can be used in CDC computers is also available. A ventilation network consisting of 531 branches, 300 nodes and 5 fans took 48 seconds for solution on The Pennsylvania State University's IBM 370/168 computer. Appendix I of this report is the User?s Manual for the program. Appendices II and III contain the input data listing, and selected output listing for; the application. Appendix IV provides tables for leakage, friction factors and shape factors.

Jan 1, 1977

By R. V. Higgins

The, large volumes of low A. P. I. gravity oil that will remain in many shallow fields of California when such oils no longer can be recovered profitably by pumping are important potential sources of oil when ways and means are found to remove them from the reservoir sands. Estimated ultimate oil recoveries in many of the "low-gravity fields" of the San Joaquin Valley in California indicate that less than 25 percent (on the average) of the original oil will be recovered. These oils have viscosities of 1,000 or more centipoises at reservoir temperatures and, because of their high viscosity and low intensity of the reservoir pressure, the quantities that will be retained in the sands ultimately are so large and their recovery is such a challenge to petroleum engineers that the Bureau of Mines has made the study of their possible recovery one of its major projects. The fact that a slight increase of temperature materially reduces the viscosity of low A. P. I. gravity oils has 'prompted the use of various means for increasing the temperature of the oil in the reservoir sands and hence the rate of flow and Completeness of recovery of the oil. Hot oil, hot water, heated air, and natural gas, steam, super-heated steam, and the products of combustion have been circulated in wells to raise the temperature of the oil it the sands; electric heaters have been installed in wells, and butane and air have been intermittently exploded and the flames propagated through the tubing to the "pay" zones. None of the methods, however, have been entirely satisfactory for the recovery of large quantities of oil.

Jan 1, 1949

By Mark Sheppard

This paper is the third of a series recording the results of tests made at various quarries throughout the United States to determine (1) the relation between the size gradation of feed to, and product from, primary crushers, (2) the particle shape of the crushed. product, (3) the differences in gradation and particle shape produced by different types of primary crushers, and (4) the differences in gradation and particle shape caused by crushing different kinds of stone. Progress reports 1 and 2 dealt with comparisons of different types of crushers crushing the same type of stone. This report deals with relation¬ship between feed and product of two different limestones, as to size distribution and particle shape, when crashed in the same crusher.

Jan 1, 1938

By G. W. Birge

Carbonizing properties of the principal coal beds of Butler County, Pa., are described in this report by the Bureau of Mines. Eight samples, representing the Upper Freeport, Lower Freeport, Upper Kittanning, Middle Kittanning, Lower Kittanning, Clarion, and Brookville beds, were carbonized at 900° C. by the Bureau of Mines-American Gas Association (BM-AGA) method. Butler County coals rank as high-volatile A bituminous and are generally characterized by high sulfur content compared with Appalachian coals used for industrial coking. If cleaned, the Brookville and one sample of Upper Freeport coal would be acceptable as the major component of metallurgical coking blends. The other Butler County coals tested would be unsuitable for this purpose because of either excessive sulfur or poor coking properties.

Jan 1, 1962

Mine fires pose a serious hazard to the health and safety of mine workers. They occur regularly and their effects can be devastating. Objective Provide mine safety personnel, MSHA, and equipment manufacturers with a comprehensive, up-to-date, and well-documented database of metal and nonmetal mine fire incidents in the United States from 1950 to 1984 and perform a statistical analysis of these incidents. The data-base is designed for use by mine engineering and safety personnel to aid in determining especially hazardous practices or conditions.

Jan 1, 1988

By Glenn L. Cook

Correlations between mass spectra and molecular structures of 186 organic sulfur compounds are discussed. The olefinic ions, the alkyl ions, the CnE2n+1 ions, the m/e 61 ions, and the m/e 35 ions in the spectra of thiols are related to molecular structure. In the spectra of sulfides, the olefinic ions, the m/e 61 ions, the m/e 35 ions, the CnH2n+1S+ ions, and the CnH2n+1SH+ ions are correlated with molecular structure. For disu1fides, the correlations relate HSSF+& and RSSH+ ions to molecular structure. Base peaks of alkylthiophenes are correlated to their molecular structures. Some unimolecular reactions of sulfur compounds in the mass spectrometer are considered. A cyclic intermediate is suggested for the reaction which produces m/e 47, CH3S+, and m/e 48, CH4S+, ions in the spectra of sulfides. An expanded ring is suggested as a possible intermediate in the reactions of thiophenes. Heats of formation of sulfur-containing ions and their appearance potentials are presented in tabular form. Ionization potentials for sulfur-containing radicals and molecules are also given. Discussion of the spectra, tabulated in the appendixes, provides an insight into the relationship of the molecular structure of a compound to the mass-to-charge ratios and the intensities of the ions in its mass spectrum. Correlations of the mass spectra with molecular structures are empirically developed by observing regularities in the spectra of the reference compounds. Correlations extend the usefulness of mass spectra because they can be employed to determine the molecular structure of an unknown compound.

Jan 1, 1965

By James R. Boyle

The value of Alabama's nonfuel mineral production in 1980 was $328.6 million, a decrease of $7.8 million from 1979. Cement, crushed stone, lime, clays, and sand and gravel continued as the major commodities produced. Alabama led the Nation in the production of crushed marble; was second in bauxite; third in native asphalt, ferroalloys, kaolin, and oyster shell; fourth in dimension marble, masonry cement, and bentonite; and fifth in fire clay and lime. Alabama ranked in the top 20 States in total value of non-metallic minerals produced. Adverse economic conditions in the construction and metals industries impacted on the minerals industry in Alabama. Mineral producers supplying raw or finished materials to these industries experienced periodic reductions in sales during the year. Unit price increases did not keep up with inflation.

Jan 1, 1982

By C. M. Frost

Two Federal Bureau of Mines recycle hydrogenation experiments to prepare catalytic cracking feed stock were made at 3,000 pounds pressure with crude shale oil retorted from Green River (Colo.) shale in the gas-combustion retort. The hydrogenated product from the first experiment, made at 784° F., was used for investigating the effects of nitrogen content on catalytic cracking yields and for determining the quality of the catalytically cracked gasoline. Hydrogenated product containing 0.14 percent or more of nitrogen produced less gasoline when cracked in a CAT "A" unit than was obtained from East Texas light gas oil cracked at the same conditions; product containing 0.10 percent or less nitrogen produced a quantity of cracked gasoline equal to that obtained from the East Texas light gas oil. The catalytically cracked gasoline had research octane numbers calculated to be approximately 95 clear and 103 with 3 ml. of tetraethyl lead. The principal product from the second experiment, made at 828° F., was a low nitrogen content gas oil which was used for investigating the yields of cracked products obtained when it was catalytically cracked to different degrees of conversion. Yields of cracked products, when plotted as functions of conversion, were essentially the same, within the experimental range of the data, as published yields from catalytic cracking of East Texas heavy gas oil; however, yields from cracking the shale-oil product did not display the sensitivity to change of cracking temperature that has been found for East Texas gas oil.

Jan 1, 1960

By D. L. Paulson

The Bureau of Mines used 50-and 800-kva electric-arc furnaces to confirm the feasibility of producing ferronickel in electric-arc furnaces from pre-reduced concentrate from the Yugoslavian FENI project. The relationships were established among metallic iron concentrations (degrees of prereduction), ferronickel grades, and nickel recoveries. Smelting the concentrate containing 1.27 wt-pct nickel and metallic iron levels between 2 and 3 wt-pct, produced 15 to 20 pct ferronickel. Higher or lower metallic iron concentrations were compensated by adding oxide pellets or carbon to the electric-arc furnace charge. Over 90 pct of the contained nickel was recovered when up to 20 pct ferronickel was being produced. Data obtained while smelting 16 tons of prereduced concentrate in the 800-kva electric-arc furnace indicated ferronickel can be recovered at an energy consumption of 530 kwhr/ton of prereduced material.

Jan 1, 1977

By Harry E. Brownlow

The United States Bureau of Mines contracted Norecol to prepare a report identifying the regulatory processes associated with metal mine development in British Columbia using the Snip Mine as a case study. The intent of this study is to assist industry and regulatory agencies in developing understanding as to differences in objectives, perspectives and operating methods. The case study will be incorporated into a larger report summarizing the comparative advantages and disadvantages of metal mine permitting in British Columbia and Alaska. The purpose of the report is to identify the development schedule and permitting process at Snip which will assist the U.S. Bureau of Mines in suggesting improvements in environmental review and permitting processes for mine developments. The report provides an abstract of the environmental assessment review processes in Canada and the Mine Development Review Process in British Columbia and provides an understanding of the linkages between policy, legislation, and environmental review.

Jan 1, 1992

By Glenn C. Reed

The Sheep Creek iron deposits, Meagher County, Mont., were investigated by the Bureau of Mines in 1943 and 1944. Work undertaken included exploratory trenching, churn drilling, petrographic studies, and detailed beneficiation tests. It was determined that the Sheep Creek ores occur both as fissure filling and bedding replacements in thin-bedded shale and arenaceous limestones of the Algonkian Belt series. At least five stratigraphic horizons were found to be mineralized. Metallurgical studies indicate that the ores are not amenable to beneficiation by present-day low-cost methods. Details of geology, sampling, and beneficiation tests are presented in this report.

Jan 1, 1949

By J. M. Stuve

In this Bureau of Mines investigation, the low-temperature heat capacities of polycrystalline phases corresponding to the sulfide compounds CoSO?89' CoS1?33, and CoS2 were measured by adiabatic calorimetry within the nominal temperature range 5 to 300 K. The derived absolute entropies S298 were 10.36±O.02, 12.96±O.03, and 16.31±O.03 cal?mol-1?K-l, respectively, assuming third-law behavior. In addition, the standard enthalpy of formation 8Hf298 of CoSO?89 was determined by bromine solution calorimetry. The derived value of 8Hf298 was -50.63±2.1 kcal?mol-1, based on the 8Hf298 of Co0. This result is considerably more negative than previously published formation values based on high-temperature gas equilibrium studies.

Jan 1, 1985