Search Documents

By C. M. McKinney

Bureau of Mines routine crude-oil analyses of 42 samples from 37 fields in the major producing areas in Mexico are presented in this report. Table 1 includes information on the source and general characteristics of each sample. Table 2 gives a summary of analytical and computed data. A map (fig. 1) shows approximately where the samples were obtained. ACKNOWLEDGMENTS Grateful acknowledgment is made to Alfonso Barnetche, manager of production, and Ing. Francisco Inguanzo, assistant manager of production, both of Petroleos Mexicanos, who supplied the crude-oil samples and furnished information concerning their sources.

Jan 1, 1960

By C. H. Riggs

This report describes the geology and reviews the oil-production history of the Dutcher sands of Pennsylvania age in the Muskogee oilfield. The geology and production history are presented not alone as a review of the past behavior of the field but also to interpret the possibilities for future production of oil from semidepleted sands in this and similar areas. The Muskogee field, one of the oldest oil-producing areas in Oklahoma, yields paraffin-base oil of 40° API gravity -a gravity higher than that of most Oklahoma oils. Oil was discovered in the townsite of Muskogee in 1894 but was not produced in commercial quantities until 1904. A peak yearly rate of 1,340,000 barrels of oil was attained in 1910 (see table 1).

Jan 1, 1959

By M. C. Malamphy, A. H. Reed, G. K. Dale, T. M. Romslo, A. Ollar

"PREFACEA general description of the activities and results of bauxite investigation by the Bureau of Mines at its bauxite project in Saline and Pulaski Counties, Ark., has been given in Report of Investigations No. 4251. The factual data obtained during the project are reported in a series of Reports of Investigation beginning with No. 4251, of which this is the fourth. The data are accompanied by maps showing the location of holes drilled and the deposits developed.Each area upon which work was done is reported by half townships. Each bauxite deposit investigated was assigned a name and a number for ready reference and identification, and its location and name are shown on the appropriate half-township map. The description of each half township is followed by a description of each deposit developed in that half township.The 14 half-township maps and 77 detail maps of the bauxite deposits in this series of reports give the locations and numbers of all the holes drilled on the project except the deep holes drilled to test the geophysical anomalies. The locations of those holes show on Figure 13 in Volume 1. The descriptions of the deposits developed are followed by complete detailed logs of the drill holes.Many of the widely spaced exploratory holes did not discover bauxite of minable thickness and grade. The pertinent information obtained from the widely spaced exploratory drill holes has been summarized and tabulated, and a table for each half township is given with the discussion covering that area."

Apr 1, 1948

By P. H. Mutschler

The Bureau of Mines studied the Chattanooga Shale to determine the quantity and quality of the uranium resources present and to assess specific environmental effects of mining the shale. Geologic data and chemical analyses, mainly concerning a 12-county area of Tennessee, were compiled from previous published and unpublished reports. Uranium resources in the Gassaway Member of the Chattanooga Shale in this 12-county area were estimated to be between 4.2 and 5.1 million tons, contained in 76 to 91 billion tons of shale. These figures represent inground tonnages and do not allow for mining or processing losses. Depending upon efficiency of mining and processing systems, enough uranium could be available to satisfy a large part of the cumulative domestic and world demand through the year 2000. A model was developed which assesses the total tons or acres of shale to be mined if the Gassaway Member were to satisfy 1 percent of the United States demand for uranium in 1991. This partially demonstrates the environmental impact of mining the shale and is easily factorable to any specified demand.

Jan 1, 1976

By E. W. Dean

A previous report of the Bureau of Mines* has supplied data for the physical and chemical properties of samples of crude petroleum produced in the eastern fields of the United States. It was issued as a preliminary chapter of a bulletin which is to cover the results of a survey of the entire country. The present report is a second preliminary chapter including figures that are available for the producing fields of the Rocky Mountain district. Work is being continued. with a series of samples from the States of Kansas and Oklahoma which will be described in a third preliminary chapter, to appear at a subsequent date. Acknowledgments. The obtaining of samples was rendered possible through the courtesy of representatives of a number of producing and refining companies operating in the Rocky Mountain district. The Bureau hereby acknowledges its appreciation of the hearty spirit of cooperation that was universally encountered.

Jan 1, 1921

By J. F. Barkley

Field tests were made on the rate of corrosion of 30 materials used in air preheaters under regular operating conditions, and the buildup of deposits was observed. Twenty-three materials were tested with coal as the fuel on an underfeed stoker and seven with oil, including a short period with pulverized coal as fuel, The plant equipment is described, and pertinent plant operating data are tabulated. Figures 17 and 19 (pp. 24 and 27) give the results of corrosion tests on the uncoated metal test specimens. The information obtained from these tests follows the general pattern described in Bureau of Mines Report of Investigations 4996, Corrosion and Deposits in Regenerative Air Preheaters. The deposits were similar, and the corrosion rates of Cor-Ten and Mayari-R steel (previously found to be essentially the same at the Harding Street Station using coal) continued to show little difference at the Marion Generating Station using principally oil. The one high-alloy steel tested, type 321, showed a much higher corrosion rate than the low-alloy steel, Cor-Ten.

Jan 1, 1959

By G. S. Rice

The recommendations of the Bureau of Mines on rock dusting practices are embodied, except in a few details, in the Recommended American Practice for Rock-Dusting Coal Mines to Prevent Coal-Dust Explosions, approved by the American Engineering Standards Committee. December 30, 1925. It is specified that the dust to be used is of a elm that all will pass through a sieve having 20 meshes per linear inch and that 50 per cent or more will pass through a sieve having 200 meshes per linear inch. Thus the coarsest size of dust and the minimum proportion of fine dust are specified, but the specification does not indicate whether a larger proportion of fine dust would be desirable. There have been advocates of the use of that size of rock dust of which the particles would all approach 200-mesh in fineness. Explosion tests were made in the Experimental mine in the earlier period of testing which indicated that the finer rock dust is somewhat more effective under test conditions, but not sufficiently so to Justify the cost of finer grinding of the dust; also there are some disadvantages of finer dust described hereafter.

Jan 1, 1930

By R. V. Ramani, R. Bhaskar

"IntroductionThe behavior of dust clouds in mine atmospheres has been a subject of longstanding interest due to both health and safety reasons. Pioneering studies in Germany and SMRE focussed on ambient dust concentration, principally aimed at determining optimum velocities for effective dilution. A summary of studies related to this area is provided by Hall,(l) Efforts to understand dust deposition from the explosion hazard point of view led to experiments in return airways (2-4) followed by experiments in longwalls.(5) Concerted efforts, either experimental or theoretical, were not made until recently to relate ambient concentration with dust deposition in mines. In 1974 Hwang et a1 (6) developed a computer model to predict dust concentration which considered deposition-concentration relationships. Also, experimental studies involving concurrent dust deposition and ambient concentration were conducted in the U.S. by Courtney et al (7 ) in operating mines. Efforts to relate theory with experimental results have been made by Owen (8) and Hwang et al (6 ) for dust deposition. There has been limited work, however, to determine the application of the theories and assumptions from aerosol sciences for modeling dust flows in mine atmospheres. (9 ) This is the objective of the work currently underway in the Generic Technology Center on Respirable Dust since· 1983 under a project titled, ""Prediction of Ambient Dust Concentration in Mine Atmospheres."" The scope of the project activities include:1. Development of a mathematical model to predict dust deposition and concentration in mine atmospheres.2. Experimental studies on dust transport and deposition in mine airways.3. Comparison of the model results with the experimental data."

Mar 1, 1989

By Keith D. Rosbury

The basic objective of this project was to determine the cost-effectiveness of dust control used on unpaved mine haul roads. Field testing was conducted at three surface coal mines (two in Wyoming, one in southern Illinois) for a total of 20 weeks. The highest control efficiency measured for a chemical dust suppressant, 82 percent, was for calcium chloride two weeks after application. Generally, however, the control efficiencies hovered in the 40 to 60 per-cent range over the first two weeks since application, and then decreased with time. After the fifth week, the limited number of data points suggest a control efficiency of less than 20 percent. Composite watering data were fairly uniform. Watering once per hour resulted in a TSP control efficiency of approximately 40 percent. Doubling that application rate increased the control effectiveness by about 15 percent to 55 percent. Chemical dust suppressants (primarily salts and lignons) can be shown to be more cost-effective than watering under some conditions. Delta summaries and the analysis of data are contained in Volume I. Volume II contains basic data.

Jan 1, 1983

Rapidly identify unstable mine waste embankments and similar dam structures. Approach Aerial photography, geotechnical instrumentation, and telephone or satellite data transmission are used to supplement walk-around inspect ions. How It Works Embankment stability and other indicators of structural integrity are evaluated using aerial photography, and on-site unattended instruments and data transmitting systems. Evidence of external movement and water seepage is obtained from aerial photography and photogrammetric evaluation techniques. Surface points marked by stake- mounted targets are monitored photographically at time intervals of several weeks or months. Photographic measurements of x, y, and z coordinates of these points are obtained from flying a series of photo-runs over the dam.

Jan 1, 1979

By E. W. Dean

This report on the physical and chemical properties of typical crude oils of Oklahoma is the sixth in a series of preliminary chapters of a bulletin covering the producing districts of the United. States. Preceding reports* may be obtained on request. The details of the methods used in this survey in collecting samples, making laboratory tests, and interpreting results are discussed in the first three papers. If any errors or omissions are noted by readers, it is hoped they will be brought to the attention of the Bureau of Mines for correction before the appearance of the permanent report. Samples of Oklahoma crudes analyzed in this report were taken from those fields representing the major production of the State. The Oklahoma Geological Survey designates 172 different oil and gas fields in the State, S1 being in Osage County, 14 in Tulsa County, 14 in Okmulgee County, 9 in Washington County. The list of samples collected by the Bureau of Mines represents only 5 fields in Osage County - Bigheart, Burbank, Hominy, Osage Junction, and Pershing - yet these samples, together with those from adjoining fields, are representative of nearly all crude produced in the county. The sample 'from the Pershing field, for example, is representative of the crude produced in several fields in that part of the county - such as Nelagoney, Pawhuska, Wyomona - and the sample from the Skiatook,

Jan 1, 1922

By E. J. Murphy

"INTRODUCTION This investigation is a continuation of previous work 3/4/5/ on the gaseous products of permissible explosives with and without sheaths. The range of oxygen balance of the explosives has been considerably increased. As has been shown previously, certain approximate relations exist between the volumes of gaseous products and the oxygen balance. Further systematization of the data is not feasible, since the method of theoretioal calculatln of the gaseous product is not yet satisfactorily developed. In a previously described method, 6/ it has been assumed that the explosion occurs at constant volume and that thermodynamic equilibrium is established. Apart from the presumably less important uncertainty of some of the thermodynamic data, it is not known how the confinement of the shots in the Bichel gage or the Crawshaw-Jones gage should be treated, or whether thermodynamic equilibrium is fully attained; nor can the extent to which the equilibrium composition changes during the subsequent period of expansion and cooling be judged with any reliability. Therefore, no calculations have been attempted. However, in anticipation of possible future theoretical interest and as an aid in answering practical problems, the new data are presented in the same minute detail as was done previously."

Mar 1, 1948

By Carlton E. Brown

This report contains information on the relation between and precision or reproducibility of counts (light-and dark-field) of the dust in liquid from simultaneous impinger, midget-impinger, electric-precipitator, and filter-paper samples. The impinger was the main sampler used from about 1922 to 1939 by industrial hygienists in the United States for collecting samples of unhygienic dust from the atmospheric environment of workers. The midget-impinger, a small modification of the preceding impinger described in 1937, has been the sampler used most since about 1939. Electric precipitators5/6/ have been used to a limited extent, mainly by the Bureau of Mines in the laboratory, for obtaining results comparable to impinger results. A filter-paper sampler for obtaining results comparable to impinger results has been described by Brown. All these samplers have a high collecting efficiency for particles larger than 1 micron in diameter revealed by the usual light-field counting procedure. However, their collecting efficiencies are quite variable for the smaller particles revealed by the dark-field counting procedure used in this study. Published information on the relation between the results of these samplers is limited and scattered. Summaries of some of this information are given in this report along with some previously unpublished information.

Jan 1, 1949

By H. M. Cooper

The determination of moisture in coal is an empirical test, because the time, temperature, and equipment are specified. The essential features of the equipment and details of the procedure are given in A.S.T.M. Designation: D271-44.:2. According to the specifications, the following features should be incorporated in the equipment used: 1. Oven must have uniform temperature in all parts. 2. Oven must be constructed with minimum of air space. 3. Oven must have means of changing the air two to four times per minute. 4. Air must be dried over sulfuric acid (sp. f-7. 1.84). The analytical procedures governing most of the nation's coal purchases are those given in A.S.T.M. Standards referred to above. These standards are general arid of such scope as to cover all ranks and types of coal. In cases where only the moisture is required, a faster method than the standard procedure is desired.

Jan 1, 1948

By Michael D. Balen

The U.S. Bureau of Mines (Bureau) is currently conducting a four-year study to assess the mineral resources and the mineral development potential of the 5.7 million acre Valdez Creek Mining District (VCMD) located in southcentral Alaska. The VCMD study is part of the Bureau's ongoing statewide mining district evaluation program. This report is a summary of the 1988 field work. The field work involved collection of reconnaissance placer and rock samples, and also involved sampling and examination of the mines, prospects, and mineral occurrences which were identified by literature research of the geology, exploration history, and mining history of the district. During the 1988 field season, Bureau personnel spent a total of 11 weeks in the field, collected 1,006 rock and placer samples, and located, mapped, and sampled 106 of the known mineral occurrences. The Bureau has visited 243 of the 250 known mineral occurrences during the course of the VCMD project. Reconnaissance sampling for placer occurrences resulted in the identification of 4 previously unreported gold placer occurrences, and identification of 5 occurrences that contain detectable levels of platinum or palladium. Reconnaissance sampling for lode sources of base and precious metals resulted in the identification of 5 new Lode gold-silver occurrences, identification of 2 occurrences that contain elevated quantities of chromium, cobalt, nickel, palladium, and platinum, and identification of one occurrence that contains elevated quantities of copper, molybdenum, anti zinc.

Jan 1, 2011

By Dupuy. Leon W.

"INTRODUCTION For many generations the Indian tribes of the southwestern deserts knew of the thermal springs of the Coso District in southwestern Inyo County, Calif. Belief in the reputedly healing qualities of the waters and muds of the area was widespread. F. J. Sanders discovered mercury in the siliceous sinter around the hot springs while he was exploiting the district as a health resort. In searching for new domestic sources of supply of strategic minerals, authorized under the Strategic Materials Act, 3/,the Geological Survey 4/ first examined the deposits, which were drilled and sampled by the Bureau of Mines in the spring of 1941.The deposits investigated comprised three units known, respectively, as The Devils Kitchen, Nicol, and Wheeler. Most of the work was done at the first two.Of particular interest in the Bureau's work on the project was the adaptation and use of the bucket drill as a tool for sampling shallow, soft ore deposit."

Mar 1, 1948

By H. V. Makar

The Bureau of Mines successfully demonstrated, on a pilot plant scale, a sodium sulfate (Na2S04) refining process for removal of copper from molten ferrous scrap. Previous tests established technical feasibility on a bench scale for achieving low copper concentrations and determining the principal factors controlling process efficiency. The pilot plant study involved a 1-ton arc furnace for melting ferrous scrap and a 1-1/2-ton treatment ladle. Results of these tests showed that copper removals obtained in laboratory tests (approximately 40 relative percent copper removal with 10 weight-percent surface addition of sodium sulfate) could be achieved on the pilot plant scale when excess carbon was added with the sodium sulfate compacts. Data were obtained on temperature losses and carbon consumption related to Na2SO4 treatment.

Jan 1, 1974

By M. P. Board

The U.S. Bureau of Mines, under a cooperative agreement with Hecla Mining Co., conducted a rock mechanics study at four widely spaced horizons in a deep mine shaft in northern Idaho. The objective of the project was to measure and analyze rock deformation and lining behavior during construction of a deep shaft in a high in situ stress field within an isotropic rock mass. Rock mass displacements were monitored with multiple-position borehole extensometers. Liner stress and strain were measured with concrete pressure cells and embedment strain gauges. This report discusses the general trends and magnitudes of data from the four test sites, and relates the data to a proposed anisotropic constitutive model for the rock mass. A design procedure is then outlined for specifications of liner thickness and support installation sequences for future shaft sinking.

Jan 1, 1989

By Stephen Krickovic

A degasification experiment was conducted in a Pocahontas No. 3 coalbed mine in Virginia. It involved (1) drilling holes in the coalbed in the out-side headings of a set of five being developed in virgin area, and (2) con-ducting a methane emission rate study as mining progressed and additional holes were drilled. Degasification from all drill holes except the longest in each of the outside headings and the first three drilled (excluding the in-situ pressure hole), was erratic and inconsequential in methane emission rates. The two longest holes liberated 66 and 79 cfm of methane, which is significant for the coalbed, but such quantity lasted a relatively short time; the first three were uniform but low in methane emission.

Jan 1, 1972

By J. D. Kalasky, Stephen Krickovic

A degasification experiment was conducted in a Pocahontas No. 3 coalbed mine in Virginia. It involved (1) drilling holes in the coalbed in the out- side headings of a set of five being developed in virgin area, and (2) conducting a methane emission rate study as mining progressed and additional holes were drilled. Degasification from all drill holes except the longest in each of the outside headings and the first three drilled (excluding the in-situ pressure hole), was erratic and inconsequential in methane emission rates. The two longest holes liberated 66 and 79 cfm of methane, which is significant for the coalbed, but such quantity lasted a relatively short time; the first three were uniform but low in methane emission.

Jan 1, 1972