Search Documents

By John B. Gayle

The coking time has considerable influence on the throughput of a coke oven, and for this reason a large number of papers dealing with the relationship between coking time and the different operating variables have been published. Although all factors known to influence the coking time have been studied, agreement has not been reached on several questions.2/3 Therefore, it appears worthwhile to evaluate any data that become available during investigations of the carbonizing properties of various coals and coal blends. Because it is expected that reports covering several different phases of this problem will be forthcoming as additional data-become available, the following study of the relationship between coking time and bulk density represents a report of progress on the overall investigation of factors influencing the coking time in slot-type ovens. The practice of including coarse coal in the blend going to the ovens to obtain increased bulk densities is well known. Similar increases have been realized by adding small quantities of oil to the coal mix. Although it would appear that such procedures provide inexpensive methods for increasing the capacity of existing coke-oven installations, Ramsburg and McGurl4/ point out that this increase is possible only if the additional coal can be carbonized in the same coking time as regularly employed without using abnormally high flue temperatures. This statement is in substantial-agreement with the position of Auvil and others5/ and implies that any change in bulk density may be accompanied by a corresponding change in coking time. On the other hand, a recent review of proposed methods for calculating the time required for carbonization6/ includes a number of equations that completely ignore the effects of variations in bulk density.

Jan 1, 1954

By M. M. Fine

This Bureau of Mines report describes the theory, experimental procedures, and the results obtained to date in the development of the Bureau's process for magnetically roasting iron ores using scrap iron as a means of reduction. Since magnetic separation is an operational step common to magnetic taconite plants, the preliminary research studies emphasized only the novel magnetic roasting step. The studies included the use of automobile scrap, ferrous reductants such as borings and turnings, and prereduced pellets. Technical feasibility of the process was demonstrated both on a bench- and pilot-scale. Quality magnetic concentrates with recoveries of over 90 percent were obtained from a direct shipping ore containing 59.5 percent Fe and from fine grained semitaconites with about 30 percent Fe.

Jan 1, 1966

"Research on the control of exposure to respirable contaminants in mine atmospheres is conducted in five areas; 1) control of dust generation, 2) dilution, dispersion and collection of dust in mine airways, 3) characterization of dust particles, 4) interaction of dust and lungs, 5) relationship of mine environment, geology, and seam characteristics to dust generation and mobility. The distribution of research findings to the mining industry, to government agencies, and to scientists at other universities is accomplished in several ways.A data bank of respirable dust samples displaying a wide range of characteristics (low volatile, medium volatile, high volatile, silica fireclay, rockdust) has been established by the Center. This data bank is being utilized by Center researchers in a suite of medical, scientific, and engineering tests (FIGURE 26).The Center has honored requests for educational and informational materials from several sources, including MSHA and CANMET who received information on Center generated software and used the Center's expertise in developing a computer program for particle distribution model (DISFIT).The Generic Mineral Technology Center for Respirable Dust has organized two dust conferences on respirable dust, the Coal Mine Dust Conference, held at West VirginiaUniversity, Morgantown, West Virginia from October 8-10, 1984 and Respirable Dust in the Mineral Industries: Health Effects, Characterization and Control, an international symposium on Respirable Dust in the Mineral Industries held at The Pennsylvania State University, University Park, Pennsylvania from October 14-16. 1986. These conferences were co-sponsored by the U.S. Bureau of Mines, Mine Safety and Health Administration, National Institute for Occupational Safety and Health (NIOSH), and the American Conference of Governmental Industrial Hygienists (ACGIH). On August 23-26, 1988, the VIIth International Pnuemoconioses Conference was held in Pittsburgh, Pennsylvania. While not a sponsor of this conference, researchers in the Generic Mineral Technology Center for Respirable Dust had significant participation with sixteen (16) papers presented (see Volume 8 of this series for abstracts and papers). These conferences provided a significant forum for the exchange of ideas on dust research and the interchange of research findings. The proceedings from these conferences are available from NTIS and ACGIH.In sum, significant benefits to mine worker health have resulted and should continue to result from the synergistic scientific, engineering, and medical research in respirable dust (FIGURE 27). As always, an important objective is the rapid dissemination of the results of this research to industry. Video tapes and the Bureau's Technology News series have been a very effective means of USBM technology transfer. Individual no-cost subscriptions to the Technology News series are available from the U. S. Bureau of Mines, Branch of Technology Transfer, 2401 E Street, N.W., Washington, DC, 20241."

Aug 31, 1989

By W. F. Dietrich

1. On St. Thomas and St. Croix, and possibly also on St. John, low-quality red-burning clays probably can be developed to provide the major part of the raw materials for structural clay products and earthenware pottery. 2. The potential sales volume for structural clay products is too small to sustain a plant in the Virgin Islands to manufacture such products in competition with Puerto Rico; however, handmade patio tile might be produced successfully. 3. The market for pottery utility wares in the Virgin Islands is too small to justify a plant devoted solely to the production of such wares; but it may be feasible to evolve a diversified community activity to make jugs, pots, casseroles, bowls, charcoal burners, patio tile, and other items.

Jan 1, 1955

1. The following recommendations should apply to all mines, tunnels and underground quarries, but to opencast quarries only in so far as persons can be exposed to dust injurious to health. General In the present state of knowledge, all duets liberated in mining, tunneling and quarrying operations should be considered potentially injurious to health if breathed in sufficient quantity; dusts containing free silica should be considered specially injurious to health, the injurious particles being below 7 microns in diameter.

Jan 1, 1954

By Eric S. Weiss

The National Institute for Occupational Safety and Health (NIOSH) and the Mine Safety and Health Administration (MSHA) conducted joint research to evaluate explosion blast effects on typical U.S. mine ventilation stoppings in the NIOSH Pittsburgh Research Laboratory?s (PRL) Lake Lynn Experimental Mine (LLEM). An innovative Australian-designed brattice stop-ping was also evaluated. After mine explosion accidents, MSHA conducts investigations to determine the cause(s) as a means to prevent future occurrences. As part of these postexplosion investigations, the condition of underground stoppings, including the debris from damaged stoppings, is documented as evidence of the approximate strength and the direction of the explosion forces. The LLEM data showed that a typical dry-stacked and coated solid-concrete-block stopping survived a total explosion pressure of ~6.7 psi (~46 kPa) and was destroyed at a total explosion pressure of ~7.6 psi (~52 kPa). In comparison, a typical dry-stacked and coated hollow-core concrete block stopping survived a total explosion pressure of ~3.4?4.3 psi (~23?30 kPa) and was destroyed at a total explosion pressure of ~3.6?5.2 psi (~25?36 kPa), depending on the length of the pressure pulse and the value of the pressure-time integral. A typical steel panel stopping design survived a total explosion pressure of 0.8 psi (5.5 kPa) and failed at a total explosion pressure of 1.3 psi (9 kPa). The LLEM data also showed that an obstacle blocking the path of a pressure wave resulted in a higher reflected pressure at the obstacle. An 8-in (20-cm) thick wet-laid solid-concrete-block stopping coated on one side survived a total explosion pressure of ~26 psi (~180 kPa); this stopping was not tested to failure. A 6-in (15-cm) thick wet-laid solid-concrete-block stopping coated on one side survived a total explosion pressure of ~14 psi (~97 kPa) and was destroyed at a total explosion pressure of ~25 psi (~172 kPa). An innovative Australian woven cloth stopping survived an explosion pressure of 4.0 psi (27 kPa) and was destroyed at an explosion pressure of ~6.1 psi (~42 kPa). These results will help investigators determine the approximate explosion forces that destroy or damage stoppings during actual coal mine explosions.

Jan 1, 2008

By James H. Cobbs

The purpose of this study is to investigate the application of boring equipment to the production of anthracite coal from steeply pitching beds. Both raise boring and augering equipment were considered. Previous studies (11) have indicated that boring equipment may have definite applications to the development of steeply pitching anthracite beds. This investigation was to carry forward previous work to determine the possible application of the two different types of equipment being considered. Previous conclusions have been substantiated by the results of this study.

Jan 1, 1975

By D. E. Hirsch, J. W. Davis, Norman G. Foster, F. G. Schwartz

This investigation was undertaken to identify nitrogen , oxygen , and sulfur compounds (polar components ) found in catalytically cracked distillate fuel . It is significant that these compounds concentrate in the sediments and gum that form when the fuel is stored . The polar components were divided in three portions by elution from a chromatographic column filled with alumina . After the hydrocarbons were washed through the column with pentane , a benzene eluted extract was removed followed by an ether eluted extract and then an alcohol desorbed fraction . These extracts were individually distilled in a molecular still and the fractions were analyzed by gas chromatography , mass spectrometry , infrared spectrometry , and elemental and functional analyses . Naphthalene and its homologs , phenanthrene and its homologs , and other compounds such as methyl indene , C₂ quinolines , phenyl indan , and the benzothiophenes , appear in the benzene extracts . Quinolines are the major components of the lower boiling fraction of the ether extract , although carbazoles , acridans , and indoles are present in some concentration . Elemental and functional group analyses of the alcohol fraction indicated 10 percent of the distillate portion was nonhydrocarbon , and in this portion the average molecule contained more than one nonhydrocarbon element . Compounds of such complexity are not well known , and standards for positive identification are limited .

Jan 1, 1963

By N. A. Eilertsen, Rolf S. Paine

The Bureau of Mines studied the presplitting technique used for controlling overbreakage in the walls of a vertical shaft at the U.S. Army Corps of Engineers Littleville Dam project near Huntington, Mass. The periphery of the shaft, the dimensions of which were 16-1/2 feet wide by 21 feet long and 52 feet deep, was presplit (cracked) in the solid to a depth of 48 feet prior to full-depth sinking. Presplitting prevented overbreak in a fairly soft schist and provided sound self-supporting walls which required very little scaling.

Jan 1, 1965

By Joe Maher

Adequate mine roof support to insure the safety of men and equipment is essential to successful mining. It is also expensive, amounting to more than one-fifth of the total mining cost at the White Pine mine. Cost effectiveness is therefore a prime consideration in developing optimum roof support. Roof bolt length is an important cost factor. This Phase II work compared uniform four-foot length Resin Bolts with the hitherto standard alternating four-foot and six-foot Resin Bolts, aiming at more cost-effective roof bolting. The data generated under this Phase II show that there is no discernible difference in the roof support given by uniform four-foot, and by alternating four- and six-foot, Resin Bolts in the relatively difficult ground selected for a severe initial test comparison; subsequent data from less difficult ground led to the same conclusion, namely no discernible difference between four-foot and four-six foot bolting.

Jan 1, 1975

By D. S. Kingery

Efficient transportation is necessary to complement modern mechanized mining methods. The increasing trend toward high-capacity face loading equipment has demanded equally efficient haulage methods; this has been met by increasing mine-car sizes, using larger locomotives, and increasing haulage speeds, all requiring properly installed and maintained haulage roads specifically designed for this type of traffic. The recommendations and specifications included in this circular were made to point out salient factors important to the proper construction and maintenance of track haulage roads and to serve as recommended standards for track installation and maintenance. GLOSSARY OF TERMS USED Haulageway. - The track, walkway, trolley wire, feeder lines signal end telephone lines, signals, telephones, support, and drainage of the entry referred to. Subgrede. - The base upon which the ballast is laid.

Jan 1, 1954

By E. J. Murphy, John C. Holtz

"INTRODUCTION Toxic gases in the products from the detonation of explosives are one of the hazards in blasting underground. Investigations by the Bureau of Mines 4/5/ have shown that the oxygen balance of the explosive is an important factor in the control of toxic gases. This balance is considered in determining the composition of modern metal-mining explosives for blasting underground, and application of the concept has reduced the volume of toxic gases generated.The chemical nature of the material being blasted also influences the composition of the toxic gases produced. Under some conditions of blasting in massive pryrite, unsafe concentrations of sulfur dioxide and hydrogen sulfide have been found.Experiments with the O-J apparatus 8/ have shown that there is an increase in the volume of carbon monoxide in the gaseous products when permissible explosives are detonated in contact with coal dust. Thus, reactive materials of a reducing nature adjacent to explosives loaded in drill holes may decrease the effective oxygen balance of the explosive and cause the volume of toxic gases to increase.Several blasting accessories of reducing nature have been introduced recently for use in coal or metal mines or tunnels. In practice these are loaded adjacent to the explosive where conditions favor reaction with the products of detonation. The effects of this loading on the gaseous products obtained from the shot are indicated in this report. Broad consideration was not given the efficiency, usefulness, or over-all safety of these devices, but the practical significance of the hazard resulting from increased volume of carbon monoxide is discussed."

May 1, 1942

To improve communications between mine workings and surface locations during emergency situations and for administrative purposes. The Approach: Development of a device for interconnecting phone systems which permits two-way communication between a public telephone and a mine pagerphone by authorized personnel. How It Works: The system, developed by personnel at the Bureau's Pittsburgh (Pa.) Mining and Safety Research Center, makes connections between the public phone line and mine pagerphone line. As shown in Fig. 1., incoming calls are sensed by the ring detector (4) and the system "answers" the call electronically. To reach the pagerphone system, the caller inserts an audible tone of fixed frequency through the microphone of his telephone. This tone is produced by a miniature, pocket-carried tone generator and is detected by a tone recognition circuit (5). When this hap-pens, relay, switching, and logic circuitry (6) closes the connections between the two phone systems. Simultaneously, a page activator (9) places a DC paging voltage on the mine phone line.

Jan 1, 1974

By H. W. St. Clair

This study of the rate of evaporation of zinc was undertaken as a part, of a general investigation on refining mixtures of metals resulting from melting reclaimed scrap. One of the methods by which the more volatile metals, such as zinc, magnesium, and cadmium, may be separated is by distillation. Distillation may be carried out at lower temperatures if it is done in an evacuated enclosure. The immediate purpose of the present investigation was to determine accurately the effect of temperature, pressure, and other factors on the rate of evaporation of zinc.

Jan 1, 1950

By W. K. Cunningham, Edwin A. Gee

"INTRODUCTION This paper is one of many reporting on various aspects of the Bureau of Mines program during World War II directed toward alleviation of shortages in certain critical minerals some of these papers are published as technical papers information circulars, and reports of investigations, of the Bureau of Mines or in technical journals.The investigation described in this report was begun as part of the Bureau, of Mines program to develop acid processes for the extraction of alumina from low-grade bauxites and clays. A domestic shortage of high-grade bauxite suitable for treatment by the Bayer process became acute as a result of World War II; and intensive search for a practical acid process using lower-grade alumina-bearing raw materials was therefore warranted.A survey of the various methods for extraction of alumina from clay has been presented in an early Bureau of Mines publication. 4/ The principal barrier to the successful operation of an acid process has been the difficulty experienced in developing a suitable commercial method for purifying the crude aluminum salts after the clay extraction is complete. Iron salts are the foremost contamination influence. A review of the more prominent procedures that have been proposed for separating iron and aluminum salts can be found in the well-known text on aluminum by Edwards, Frary, and Jeffries. 5/The majority of acid processes to extract alumina from clay employ sulfuric acid as the leaching agent, and the purification is thus reduced to the separation of iron and aluminum, sulfates."

Feb 1, 1948

Reduce the potential for injuries in underground mines by providing an alternative to manually lifting and holding heavy roof-support beams. The Problem I-beams, rail sections, and wooden cross-beams are often used in mine haulageways where extensive roof support is needed. Studies by the Bureau of Mines have shown that many mines must resort to manually lifting, moving and installing these beams. Such manual-handling activities have the potential for causing injury to mine workers, particularly back injuries. I-beams used for roof support can typically weigh from 400-500 lbs. Rail sections weigh about the same as the I-beams. Wooden beams can weigh from 200 to 300 lbs. To lift a single beam usually requires the efforts of 3 to 5 mine personnel.

Jan 1, 1988

By N. L. Wimmler

"INRODUCTIONSedimentary deposits of titaniferrous magnetite occur at various localities in the eastern foothills of the Teton Ranse in Deer Lodge County, Mont. The Choteau deposit was examined by a Bureau of Mines engineer in August 1942. An exploration project was recommended.Core drilling exploration was begun in June 1945; it was concluded in August 1945, Seventy-six holes were drilled. This report presents the data obtained by the Bureau of Mines exploration.ACKNOWLEDGMENTIn its program of exploration of mineral, deposits, the Bureau of Mines has as its primary objective, the more effective utilization of our mineral resources to the end that they make the greatest possible contri¬bution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, Chief, conducts preliminary examination, performs the actual exploratory work, and prepares the final, report. The. Metallurgical Branch, R. G. Knickerbocker, Chief, analyzes samples and performs beneficiation tests. Both of these branches are under the supervision of Dr. R. S. Dean, Assistant-Director. The field work was supervised by Earshel W. Newman, engineer in charge of the Helena Field Office. D. B. Hoiekvam was the project engineer; he provided most of the data used in the preparation of this report."

Dec 1, 1946

By A. B. Hooker, P. G. Guest, E. J. Gleim

"From time to time the United States Bureau of Mines has received reports of gas explosions alleged to have been caused by correctly assembled flame safety lamps. In most of the mines where the explosions occurred the lamp was in use at a working face where the velocity of the ventilating current would be relatively low. The inference has been that the lamp was correctly assembled but that the gauze became sufficiently overheated to ignite the surrounding atmosphere.As part of its routine investigation of flame safety lamps the Bureau of Mines subjects each lamp to a test in still and moving atmospheres to determine its safety. Heretofore, as long as the lam, successfully passed this and other tests no determinations as to the margin between success and failure were made; hence, in attempting to answer inquiries concerning the reported explosions it was found desirable to be able to give actual gauze temperatures as a measure of the comparative safety of lamps under various conditions. The previous laboratory tests of flame lamps in still mixtures were made in a chamber or ""gallery"" of relatively small volume where the lamps might have been subject more or less to the smothering effect of the combustion products. It was therefore decided to make a special series of tests to obtain the gauze temperatures of both bonneted and unbonneted lamps in still and low velocity mixtures, using a larger gallery to offset any smothering effect.These tests are believed to represent the first attempt at measuring gauze temperatures by means of themocouples. The results will not only be of interest but will also be helpful to many in determining the status of flame safety lamps relative to gas ignitions in mines."

Feb 1, 1929

[Determine how subsidence resulting from underground coal mining affects surface structures, and evaluate the usefulness s of the tiltmeter for monitoring foundation movement. Approach The Bureau of Mines is studying foundation response to mine subsidence in order to determine how subsidence-induced ground movements affect foundations in place directly above the mint. These investigations are essential if economic mitigation and repair techniques are to be made. In addition, commercially available tiltmeter are being evaluated (or use as a cost-effective monitoring technique. To study foundation response and to evaluate the tiltmeter system, full-scale model foundations were constructed, instrumented, and monitored for three years. Vertical and horizontal displacements, tilt magnitudes and directions, and observed damages were recorded. Displacements were compared with measured lilt to determine if the tiltmeter was tracking foundation response to subsidence, The Bureau developed a computer software package to aid in the reduction and analysis of the tiltmeter data.]

Jan 1, 1988

By Paul M. Tyler, Amy B. CLINTON

The four elements fluorine (F), chlorine (C1), bromine (Br), and iodine (I) form the most intimate family in the entire system of elements and are grouped under the name "halogens" or salt formers (by derivation from the Greek). The first member of this family, fluorine, is the most chemically active element known; and fluorspar, and to a less extent cryolite, the chief sources of fluorine, are important commercial minerals. Fluorine occurs in nature chiefly in combination with sodium as common salt, but it also appears in other natural compounds in sea water, salt-well brines, and bedded deposits. In addition to common salt, various compounds containing chlorine (chlorides) have long been consumed by industry on a large scale, and within the last two decades that element itself has come rapidly into prominence as one of the leading industrial chemicals. Bromine and iodine, the two retaining members of the family, are less abundant in nature and less readily isolated and in consequence of their relatively high price have found few industrial uses, being consumed chiefly in medicine and in photography. Bromine, however, is now entering the industrial field to a considerable extent, due to the rapidly growing use of ethylene dibromide in anti-knock compounds for gasoline. The present paper is devoted to bromine and iodine, but in order to compre- hend the physical and chemical characteristics of these two elements (and hence their potential economic significance) it is convenient to consider them as members of the family series to which they belong. The family relationship of the halogens is illustrated by the following:4 (1) The similarity in the chemical and physical properties of the elements and their corresponding compounds is such that the prop- erties of any one member of the family can be said to summarize or rather to typify the properties of all the other members, although fluorine diverges a little in some of its properties. (2) The gradual transition of chemical and physical properties is such that if the elementa are arranged in order F, Cl, Br, I the variation in any particular property in passing from fluorine to iodine nearly always proceeds in the same order, and that is the order of their atomic weight. Taxing almost any property and comparing its magnitude in passing from the element fluorine to iodine, or from the fluorides to the iodides, a similar graiation will be observed. Thus, take the melting point of the cadmium, calcium, barium, sodium, or potassium salts, in degrees.

Nov 1, 1930