Search Documents

By M. L. Glenn

The Bureau of Mines is conducting research on Fe-based alloys using Si and Al additions to reduce the Cr required for heat-resisting appli-cations. Part of this research is being done to evaluate alloys containing (8-10)Cr-(10-14)Ni-(0-8.5)Si-(0-4) Al to determine which of these alloys have austenitic structures, as well as fabrication properties and oxidation resistance sufficient to substitute for type 304 stainless steel. Based on initial results, an Fe-lOCr-11Ni-5Si alloy and an Fe-8Cr-13Ni-5Si alloy were selected for evaluation of oxidati.on, stress rupture, and tensile properties. Both alloys have oxidation resistance at 7000 and 8000 C that is better than that of type 304 stainless steel. The stress rupture strengths are less than that of type 304 stainless steel but significantly better than that of commercial heat-resisting steels with similar Cr contents. Yield strengths of the alloys were equivalent to that of type 304. Both alloys had high tensile strengths comparable to those of stainless steels that transform to martensite during straining (e.g., type 301). These alloys have weld-hot-cracking resistance comparable to that of type 304 stainless steel. This initial study shows that Si has potential as a substitute for Cr in stainless steels for heat-resisting applications.

Jan 1, 1984

By D. A. Reynolds, J. D. Davis

"INTRODUDTION Investigations by the Bureau of Mines have shown that the carbonizing properties of splint and bright coals may differ greatly. In a study of 55 coal columns selected from representative coals of the Appalachian region, Sprunk and coworkers 10/ compared various chemical and physical properties of splint and associated bright coals. Carbonization tests in the Fischer retort at 932°F. (500°C.) showed that, except for bright coals of high oxygen content, the coke residue from bright coal was much more swollen and cellular than that from splint. ·with one exception, agglutinating values determined by the Bureau of Mines test, were lower for splint than for associated bright coal.Because sorting of coal in quantity is tedious and time-consuming, separate types have not been carbonized by the Bureau of Mines-American Gas Association (BM-AGA) test, which requires 85- to 200 pound charges. However, this method has been used to determine the carbonizing properties of samples 0f bed layers that are composed largely of either splint or bright coal.4/ In these earlier tests, which were made at high temperatures on layer samples from the Elkhorn bed, Letcher County, Ky., the splint coal yielded more coke than the bright coal, and this coke was slightly stronger than that from the bright coal. The cokes from samples with large proportions of bright coal were more cellular or porous, as were the low-temperature cokes obtained from carbonization of separated samples of bright coal in the Fischer retort."

Apr 1, 1944

By Charles Vaught, Henry J. Kellner, Michael J. Brnich, Henry P. Cole, William J. Wiehagen

In 1985, U.S. Bureau of Mines and University of Kentucky researchers began a series of studies relating to self-contained self-rescuer (SCSR) donning proficiency. During the next 5 years investigators examined a number of factors that have a bearing upon miners' ability to put on and use the apparatus in an emergency: the procedure being taught; availability and utilization of training models; opportunities to practice; hygiene; and on-the-job training. This report presents an overview of that research. It is concluded that companies should adopt a hands-on training protocol that allows them to integrate SCSR donning practice into other workplace routines such as fire drills.

Jan 1, 1993

By Robert L. de Beauchamp

The Bureau of Mines reviewed aluminum chloride technology to determine the problems associated with its preparation from minerals, and to ascertain the best areas for research to solve these problems. Commercial AlC13 production processes are described and the ?state of the art? for the preparation of AlC13 from aluminous materials is evaluated. Areas for further research are indicated.

Jan 1, 1969

By George H. Holmes

The water situation in Nevada mineral and related industries is described in this report. It contains information on the sources and adequacy of supply to current operators, requirements and uses, quality and costs, geography, hydrography, precipitation and evaporation characteristics, and Nevada water laws. Also, information is given on the water requirements of one public utility powerplant, and the source and consumption of water in four major cities. Water distribution at 24 operations is shown on schematic waterflow diagrams. The mineral industries of Nevada in 1962 used 8.6 billion gallons of new' water and reused 3.8 billion gallons for a total usage of 12.4 billion gallons. The copper industry was the major water user. The 1962 value of all mineral production in Nevada was $85.5 million. The large amount of water required to maintain thin high production is obtained principally from ground-water sources in alluvial valleys and the permeable rock formations of some mountain ranges. Some water is also obtained from perennial streams and springs. Sources of water utilized by existing industry ire near most mineral industry operations; however, seven companies are forced to pipe water distances ranging from 2 to 8 miles. Although water supplies of presently operating companies are adequate at most operations, several companies resort to large-scale reuse of water as a matter of conservation and economics. Acquisition of water by new operators is possible but takes considerable negotiation. Water rights, surface and underground, are controlled by the State. The quality of the water is satisfactory for most purposes. Analyses of 19 samples, listed in the appendix, show the range in water quality at various plants throughout the State. Costs of delivering new water to current operations range from 2 to 26 cents per 1,000 gallons with an average of 10 cents per 1,000 gallons for power and maintenance. No firm costs for recirculating water were available; estimated costs range from 1.5 to 2.5 cents per 1,000 gallons. The mineral-product value of the entire Nevada mineral industry in 1962 was equivalent to $10 per 1,000 gallons of new water and $26 per 1,000 gallons consumed. Projection of the 1962 water requirements of the Nevada mineral industry indicates that the demand For new water will increase from 8.6 billion gallons in 1962 to 11.9 billion gallons in 1980, a 43-percent increase. Water requirements in the year 2000 are estimated as 14.8 billion gallons, an increase over 1962 water demand of 78-percent.

Jan 1, 1966

By George H. Holmes

The water situation in Nevada mineral and related industries is described in this report. It contains information on the sources and adequacy of supply to current operators, requirements and uses, quality and costs, geography, hydrography, precipitation and evaporation characteristics, and Nevada water laws. Also, information is given on the water requirements of one public utility powerplant, and the source and consumption of water in four major cities. Water distribution at 24 operations is shown on schematic waterflow diagrams. The mineral industries of Nevada in 1962 used 8.6 billion gallons of nee' water and reused 3.8 billion gallons for a total usage of 12.4 billion gal¬lons. The copper industry was the major water user. The 1962 value of all mineral production in Nevada was $85.5 million. The large amount of water required to maintain this high production is obtained principally from ground-water sources in alluvial valleys and the permeable rock formations of some mountain ranges. Some water is also obtained from perennial streams and springs. Sources of water utilized by existing industry ore near most mineral industry operations; however, seven companies are forced to pipe water distances ranging from 2 to 8 miles. Although water supplies of presently operating companies are adequate at most operations, several companies resort to large-scale reuse of water as a matter of conservation and economics. Acquisition of water by new operators is possible but takes considerable negotiation. Water rights, surface and underground, are controlled by the State. The quality of the water is satisfactory for most purposes. Analyses of 19 samples, listed in the appendix, show the range in water quality at various plants throughout the State. Costs of delivering new water to current operations range from 2 to 26 cents per 1,000 gallons with an average of 10 cents per 1,000 gallons for power and maintenance. No firm costs for recirculating water were available; estimated costs range from 1.5 to 2.5 cents per 1,000 gallons. The mineral-product value of the entire Nevada mineral industry in 1962 was equivalent to $10 per 1,000 gallons of new water and $26 per 1,000 gallons consumed. Projection of the 1962 water requirements of the Nevada mineral industry indicates that the demand for new water will increase from 8.6 billion gallons in 1962 to 11.9 billion gallons in 1980, a 43-percent increase. Water requirements ill the year 2000 are estimated as 14.8 billion gallons, an increase over 1962 water demand of 78-percent.

Jan 1, 1966

By Piyush K. Dutta

This report describes the design, development and manufacture of a prototype quiet hard rock stoper drill and results of its field tests. It is shown that the stoper drill noise level can be reduced from 118 dBA to below 100 dBA by using this design. The design concept of this drill is based on a valveless independent rotation system, use of an integral muffler and pivot mount. The drill was manufactured in a standard commercial drill manufacturing setup and organization. The design and production technology proved that commercially viable quiet drills can be made available for mine use.

Jan 1, 1985

By Francis C. Lincoln

"INTRODUCTION As part of a general investigation of the zinc-producing area of southwestern Wisconsin, the Bureau of Mines undertook a limited amount of exploratory drilling in the immediate vicinity of the New Dale Rundell mine, in the Mifflin District of Iowa County, Wisc.The work was carried out during the early part of 1945, at a time when all effort was being directed toward increasing production of metals important to the Nation's war program. Bureau of Mines engineers decided to conduct exploration at the New Dale Rundell mine after a preliminary study of available data showed a reasonable possibility of indicating an important deposit. Before the Bureau of Mines investigation, 50 holes had been drilled in the vicinity. Of this number, 18 encountered ore of minable grade. Subsequently the mine was developed and operated for a brief period; however, work was stopped before all of the ore disclosed by drilling had been mined. There appeared to be a correlation between the ore shown by the drilling in the New Dale Rundell mine and another disclosure some 1,500 feet to the northwest. The Bureau of Mines exploration was pinned to explore this possible correlation. Of the 7 holes drilled by the Bureau of Mines, 3 disclosed minable ore beyond the limits of previous drilling."

Aug 1, 1946

By M. C. Malamphy

A general description of the activities and results of bauxite investigation by the Bureau of Mines at its bauxite project in saline and Pulaski Counties, Ark., has been given in Report of Investigations 4251. The factual data obtained during the project are reported in a series of Reports of Investigation beginning with No. 4251, of which this is the eleventh. The-data are accompanied by maps showing the location of holes drilled and the deposits developed. Each area upon which work was done is reported by half townships. Each bauxite deposit investigated was assigned a name and a number for ready reference and identification, and its location and name are shown on the appropriate half-township map. The description of each halt township is followed by a description of each deposit developed in that halt township. The 14 halt-township maps and 77 detail maps of the bauxite deposits in this series at reports give the locations and numbers of all the holes drilled on the project, except the deep holes drilled to test the geophysical anomalies. The locations of those holes show on figure 13 in volume 1. The descriptions of the deposits developed are followed by complete detailed logs of the drill holes. Many of the widely spaced exploratory holes did not discover bauxite of minable thickness and grade. The pertinent information obtained tram the widely spaced exploratory drill holes has been summarized and tabulated, and a table for each halt township is given with the discussion of that area.

Jan 1, 1948

By James Paone

The Bureau of Mines studied the behavior of rocks at the initial state of crater formation that results from the stresses created under a drill bit to determine which mechanical properties of rock are important in rock fragmentation by drilling. Although a definite relation between the drilling strength and relevant mechanical properties has not been established, maximum yield strength of rock is apparently a parameter of drillability of rock. The strengths of rock were considered from the Mohr-Coulomb criterion from which the surface of failure was constructed. The results from previous tri-axial tests on Solenhofen limestone were adopted to verify the criterion of failure. Inelastic behavior of some rock types was observed under a low-velocity impact of a hemispherical bit and under static indentation with a similar bit. Quantitative determinations of strengths of Solenhofen limestone) Indiana limestone, and Tennessee marble were made under static indentation. The maximum yield strength estimated from the average stress over the indented area was used as the crushing strength of rock under a drill bit.

Jan 1, 1966

By M. A. Cook

Crude titanium metal, produced by the reduction of titanium tetrachloride with magnesium, is contaminated with some excess magnesium end adhering magnesium chloride when it is removed from the reaction pot. The method of vacuum 'purification is described in which the crude mixture is heated in a vacuum at a temperature of about 1,700° F. and the magnesium metal and chloride are volatilized away from the titanium, leaving it practically magnesium-free in a sponge-metal form. The pilot-plant equipment is described in detail, together with the technique of operation and methods of sponge recovery. Operating data is given, which compares ten 24- to 30-hour heats with ton 48-hour heats, and finally, power and labor requirements are discussed. Vacuum purification of raw titanium produced by the Kroll process has boon employed for treating of several tons of raw titanium with results for superior to those achieved by the method of leaching and grinding. The operations described, while on but little more than pilot-plant scale, indicate commercial feasibility of the process, even though it is a batch-typo operation. All equipment is either of standard manufacture or can be readily fabricated from standard materials, and operation of the units can be satisfactorily maintained by semiskilled labor.

Jan 1, 1952

By D. J. Bauer

The Bureau of Mines demonstrated the feasibility of fractionating lanthanide nitrates with a tertiary amine on lanthanum-cerium and thulium-ytterbium pairs. Optimum values were determined for pH, phase concentration, and percent chelation of metal ions in the aqueous phase. Percent extraction is markedly dependent on the concentration of lithium nitrate in the aqueous phase. Selective masking of the heavier element in each extraction system with DTPA or EDTA aqueous-phase chelating agents resulted in lanthanum-cerium separation factors of 8.5 and thulium-ytterbium separation factors of 3.4.

Jan 1, 1966

By Louis A. Panek

An improved centrifugal-testing apparatus has been designed and built in the Bureau of Mines laboratory at College Park, Md., which is unique in that it incorporates the use of resistance gages to measure directly the strains in a rotating model without testing it to failure. Owing to this feature, a more rapid testing method can be used; furthermore, model materials need not be restricted to those of the prototype. The behavior of any structure in which strains of significant magnitude are produced by its own weight may be studied in a small model subjected to simulated gravity loading. The model is rotated in a centrifuge to induce in it centrifugal forces, which, like the gravitational forces in the full-size structure, act on the volume elements and are proportional to the masses thereof. Centrifugal testing is, therefore, applicable to the design of mine openings and to the study of similar ground-control problems. It constitutes an experimental method for determining the state of strain in a structure for which analytical methods are excessively laborious or even impossible. In previous applications of centrifugal testing by other investigators, the models usually were tested to failure, and the analysis was made from-the type of break produced. The models were made of the same materials as the proto-type, and the test results were applied only to the particular prototype represented by the model. Beam deflections were measured from photographs of the rotating model, but no means was employed either to determine the actual distribution of stress in the model or to determine quantitatively the degree of restraint imposed on the ends of the loaded model beam, that is, to determine whether the loaded model behaved as a beam with rigidly fixed ends or as some other type of beam. With the apparatus described, it is possible to determine the state of strain, and thus the boundary conditions, in a rotating test model weighing up to 90 lb., which can be subjected to centrifugal forces up to about 2,600 times the force of gravity. The load-strain relationship, applicable directly to the prototype, can be determined from a Single model test. The test results can be presented as quantitative relations between the loads, strains, and dimensions and mechanical proper-ties of the structural members and can be applied to any prototype, whatever its component materials, that satisfies the similarity requirements.

Jan 1, 1952

By Jr. Hazen

Relationships that may exist between assays and sample interval lengths when using unequal sample intervals in mine sampling have been investigated as part of the larger research problem of adapting statistical methods to the analysis of weighted average grades. The theoretical relationship between the amount of difference in the weighted and unweighted average grade of ore and the size of the correlation coefficient between assay value and sample interval length was found to be linear. Numerous examples of actual field sample and assay data, which have been obtained by using unequal sample intervals, are documented, and the differences between weighted and unweighted average grades of ore and the correlation coefficients between assays and sample interval lengths have been computed and plotted on graphs. Differences between these actual field data and the expected theoretical linear relationship are examined. It is hypothesized that the use of unequal sample intervals in mine sampling is, in fact, stratified sampling in a statistical context. The sampler establishes stratification by selecting unequal sample intervals on the basis of differences in lithology, changes in rock type, characteristics of mineralization, or differences in metal content. Statistically} methods currently used in mine sampling, involving unequal sample intervals, fail to consider differences in the inherent variances in grade of ore within the various strata established by using unequal sample intervals. Consequently the strata are sampled with different precision. This difference in precision of sampling between strata may account for much of the deviation between the plotted points representing actual field sampling data and the theoretical linear relationship between the amount of the difference between weighted and unweighted average grade of ore and the size of correlation coefficient between assays and sample interval lengths.

Jan 1, 1966

By L. C. IlsLey

The theory and practice followed by the Bureau of Mines in investigating electrical equipment4/ made for service in gassy mines are of particular interest not only to manufacturers but also to those organizations that deal with safety anal inspection at the mines. This publication purposes to discuss the theory upon which tests of equipment in explosive atmospheres are based and to consider inspection and other matters pertaining to investigations made by the Bureau in ascertaining whether a machine merits approval. The material in this report is taken from an earlier bulletin,5/ which is row out of print, and has been revised and brought up to date to make the information again available to manufacturers, inspectors, and others interested in the development of safe equipment.

Jan 1, 1954

By J. K. Whyatt

During the past 2 years, U.S. Bureau of Mines (USBM) researchers reviewed an in situ stress investigation conducted in 1977 at a test site on the 4250 level of the Lucky Friday Mine, Mullan, ID. Although the field measurements of over core strain were found to be useful, significant deficiencies were found in the stress field estimation procedure. The stress field estimate was then updated to incorporate recent progress in statistical capabilities and new understanding of stress concentration factors for doorstopper cells, as well as to correct an error in the original stress solution procedure. Simple models were used to examine the possibility that systematic variations in material properties and stress fields existed at the site. These models succeeded in reducing the sum of squared error somewhat, but fell short of completely describing stress variations throughout the test site. This overcore measurement will be supplemented by two other measurements described in the second and third reports of this series. Other observations of stress field characteristics are discussed in the fourth report The final report will also characterize the natural in situ stress field in the vicinity of the Lucky Friday Mine. This work was undertaken to support USBM research on mining method design and rock-burst control for deep mines.

Jan 1, 2010

By L. J. Kane

While analyzing synthesis gas produced from coal, the Bureau of Mines found that conventional procedures for naphthalene determination were difficult and time consuming. The Bureau developed a rapid and sensitive turbidimetric procedure, which requires only simple instruments and hence can be used in plant-control laboratories. The gas is passed through a saturated aqueous solution of picric acid at 3° to 4° C. whose turbidity is then measured at room temperature. A dispersing agent is added to prevent coagulation of the suspension on warming. Only about 1 mg. (0.015 grain) of naphthalene need be absorbed, and precision and sensitivity are a few ten-thousandths of a grain, or a few hundredths of a grain per 100 cubic feet. The determination can be completed less than 10 minutes after absorption. INTRODUCTION One of the functions of the Branch of Coal Gasification, Bureau of Mines, Morgantown, W. Va., is to develop economical methods for manufacturing, from coal, a mixture of hydrogen and carbon monoxide for producing hydrogen, methane, and other gaseous fuels. This raw gas may contain many impurities, including naphthalene. This impurity is usually determined by first forming naphthalene picrate in a water solution of picric acid, separating the picrate, and titrating the unreacted picric acid or the picrate itself.

Jan 1, 1957

By John H. Soulé

"Bureau of Mines engineers3/ examined the White Eagle fluorspar mine on September 3, 1943, and again on February 17, 1944. The examinations led to a proposal for the exploratory project upon which this report is based. The project, which was supervised by the author and P. L. Russell, was started on April 6, 1945, and completed on June 26, 1945.Geologists4/ of the Federal Geological Survey examined, mapped, and reported on this property prior to initiation of the Bureau of Mines project.In its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests. Both these branches are under the supervision of Dr. H. S. Dean, assistant director.Special acknowledgment is due to C. H. Johnson, Rolla, Mo., Division, Mining Branch; to W. R. Storms, mining engineer in charge of the New Mexico field office; and to J. H. Hedges, chief of the Tucson, Ariz., Division Mining Branch. Acknowledgment is owed, also, to Robert Trace and Howard Rothrock, of the Federal Geological Survey, for help in mapping the surface and in logging drill cores.The White Eagle claim is in the east-central part of sec. 34, T. 19 S., R. 9 W., Cooks Peak Mining District, southeastern Grant County, New Mexico. The property is reached from Deming, N. Mex. by taking the paved U. S. Highway No. 260 northwestward for 13 miles to the junction with State Route 61. State Route 61 is a graded but unpaved road and is followed northward for 8 miles to a junction with a poor dirt road, which is followed eastward for 11 miles to the mine. Silver City, N. Hex., is about 50 miles northwest of the mine and may be reached by several routes.The White Eagle patented claim was owned by L. H. Duriez of Vanadium, N. Mex., W. D. and W. A. Howard of Deming, N. Mex., Alvan N. White of Silver City, N. hex, and: Mrs. E. M. Saunders of Los Angeles, Calif. D. P. McCabe of Lordsburg, N. Mex., a former lessee, has recently contracted to purchase the property.The White Eagle claim was located about 1920 and was patented in November 1933. It was leased to Cooper Shapley of Deming, N. Mex., in July 1933; to General Chemical Co. from August 1938 to May 1940; to Antonio Cristo from October 1940 to the fall of 1942; and f is ally it passed into the hands of D. F. McCabe of Lordsburg, N. Mex., in May 1945.Approximately 25,000 tons of fluorite ere containing about 65 percent CaF2, have been mined and shipped from this property.5/ Most of this ore was mined by Cooper Shapley and the General Chemical Co. and shipped to the General Chemical Co.'s La Purisima mill at Deming. No exact data on production are available."

Jul 1, 1946

By A. L. Engel

[This report describes preliminary tests of samples from six deposits of oxidized copper ores .in Nevada. The tests for the most part were confined to laboratory-scale acid leaching to extract the copper.'The exceptions consisted of flotation tests to demons' ate the possibilities of treating the ore by that method. The samples tested were representative of oxidized copper ores from six counties in all parts of Nevada. The results obtained by the preliminary tests described were indicative of the extractions of copper to be expected, In the five leaching experiments, the approximate consumption of acid was also indicated.]

Jan 1, 1953

By Ronald B. Stotelmeyer

This report summarizes studies of 28 National Forest roadless areas in Montana completed by the U.S. Bureau of Mines (USBM) in the period 1974-1993. It also briefly describes 20 areas for which field studies have not been conducted. All 48 of these roadless areas have been recommended for addition to the National Wilderness Preservation System or proposed as special management areas by the U.S. Forest Service (USFS) or the Montana congressional delegation. The Bureau studies indicate which parts of the roadless areas have a high likelihood for mineral-resource development. They also show where mineral production has occurred in the past and where abandoned mine workings (possible hazards) would be encountered. The number of mine and prospect workings found are a measure not only of surface disturbance, but of areas not wilderness in character. For the purposes of this report, mine refers to a property which produced (or is currently producing) a mineral commodity, a prospect is a property which has been explored but has no record of production.

Jan 1, 1994