Search Documents

By Daryl R. Tweeton

The Bureau of Mines is investigating possible applications of geophysics to monitor leachate during in situ mining. Tomographic reconstruc-tion of seismic or electromagnetic crosshole data appears applicable. The tomographic program BOMTOM (Bureau of Mines tomography) was written and then used to investigate reconstructions with synthetic travel time data. The calculations confirmed that without constraints, crosshole data do not provide unique solutions. The solution is not determined solely by the data, but is also influenced by the velocity guesses starting the iterative solution procedure. The effectiveness of constraints in combatting nonuniqueness was examined. The requirement that the velocity not vary laterally at the top and bottom of the pixel grid was effective. This constraint is realistic when the top and bottom of the grid represent dry and saturated re-gions, respectively. Limiting the maximum velocity improved reconstructions, but may not be applicable in practice. BOMTOM uses the simultaneous iterative reconstruction technique (SIRT) with straight ray paths. The program is efficient in use of memory, and can be run on a personal computer. A source code in FORTRAN is listed. A source code in BASICA and compiled executable codes in both languages are available from the Bureau's Twin Cities (MN) Research Center.

Jan 1, 1985

By Will H. Coghill

The jig men of the Tri-State (Joplin-Miami) zinc district complain about the flakiness of their mill feed. They believe that the flakiness of the composite grains of gangue and mineral are to blame for losses of zinc; that is, that the flaky grains in the jig tailings have higher zinc tenor than the cubical grains. Although the evidence which follows contradicts this belief, no effort is made to give a final and conclusive answer. On the other hand, there is outlined a positive and mechanical method which the operator may use to pursue this and similar investigations. DISCUSSION OF SCREENING METHOD Hand-sorting is obviously not satisfactory for separating cubical grains from flaky grains because the personal influence can not be removed. Screens, however, may be used with success. A set of each of two types of screens is required; namely, the square-hole type and the rectangular (rectang, oblong) type. The square-hole screens must be of the double Tyler scale; that is, the order of the sieves should be after the fourth root of two instead of the customary square root of two; close sizing is important. The size of the rectang screens may be selected by trials so that a part of the material already closely sized on the square-hole screens, will pass the oblong holes. Obviously, the cubical grains will remain on the rectang and the flaky grains will pass through. Hence the mode of operation is to screen first on square-hole screens and then split the products on the oblong-hole screens.

Jan 1, 1928

By A. C. Fieldner, W. A. Selvig

Information concerning the fusibility of coal ash has become of considerable value to the consumer of coal, mainly in connection with the troublesome formation of clinker resulting from the melting of the ash constituents of the burning coal. The growing interest in such data has led the Bureau of Mines to make a general survey of the "fusing" or "softening" temperatures of the ash from coals of the United States. It is hoped that this information when used together with the large number of coal analyses published 1 by the bureau will assist the consumer of coal in comparing different coals, and in selecting the coal best adapted for his purpose.

Jan 1, 1922

Ground and air vibrations induced by large surface blasts have been monitored. These field results, as well as a large number of published results, have been used to assess the performance of existing predictors and for the development of improved prediction methods. Field monitoring has been performed, with four seismographs giving complete wave records, at limestone quarries, coal strip mines and an open pit copper mine. Conventional analysis includes least square fitting of peak particle velocities and peak air overpressures with scaled distance formulations. Frequency content has been analyzed, and correlated with blast design (detonation sequence). Two new methods have been developed for predicting ground vibrations induced by blasting. The proposed analytical predictor accounts explicitly for inelastic attenuation and geometrical spreading, and calculates the peak particle velocity as a function of charge weight and distance. Statistical analysis of case studies confirms the consistent improvement over conventional scaled distance predictors. The second new predictor is a computer program simulating blasts, including blast geometry, charge distribution and detonation sequence, and simulating propagation of individual pulses to any point of interest, where effects are summed. A complete blast vibration results, allowing prediction of frequency content and duration as well as peak velocities.

Jan 1, 1983

By L. F. Christianson

The presence of salt in crude petroleum has been known for many years, but recently the percentage of chloride salts of calcium, magnesium, and sodium produced with some crude oils has increased to such an extent that the removal of the salty compounds is imperative for some refiners and their presence causes considerable apprehension for others. The exact reason for this increase of salts is not known definitely, but in all probability a combination of factors contributes to the condition. The most important are acidizing of wells, development of new fields producing crude oils of greater salt content, and the depletion of old fields with an attending increase in the production of emulsified brine. Due to handling

Jan 1, 1938

By L. F. Christianson

The presence of salt in crude petroleum has been known for many years, but recently the percentage of chloride salts of calcium, magnesium, and sodium produced with some crude oils has increased to such an extent that the removal of the salty compounds is imperative for some refiners and their presence causes considerable apprehension for others. The exact reason for this increase of salts is not known definitely, but in all probability a combination of factors contributes to the condition. The most important are acidizing of wells, development of new fields producing crude oils of greater salt content, and the depletion of old fields with an attending increase in the production of emulsified brine. Due to handling

Jan 1, 1938

By M. Kawahata

Methane sensors using principle of catalytic oxidation of methane are employed for determination of methane content in ambient air of coal mines. Certain foreign gases or vapors in the air poison the catalyst of the sensor effecting the sensor's response. After literature search of poison compounds of Pt and Pd oxidation catalyst, experimental studies of catalyst poison kinetics were made for three siloxane compounds, tributyl-phosphate, monobromotrifluoromethane, and hydrogen sulfide, selected as poison vapors. Concentration range of the poison vapors was varied in a range from 3000 to 0.1 ppb (v/v). Three siloxane vapors produced strong catalyst poison effect, followed by tributylphosphate, hydrogen sulfide and monobromotrifluoromethane for the high concentration level of the poison vapors. The poison effects are influenced significantly by concentration of the vapors. Threshold poison vapor concentrations where effect of the poison vapors on the sensor is minimal were determined experimentally. Experimental studies were made further for prevention method of catalyst poison by adsorption techniques. Use of activated carbon cloth inserted on the sensor's head prevented catalyst poisoning efficiently.

Jan 1, 1981

By Jr. Hazen

Two statistical techniques, the mean-square-successive-difference test and correlation, are used to investigate the problem of assigning an area of influence to an assay. Data from five hydrothermal deposits, Climax molybdenum, Cebolla Creek titaniferous iron, San Manuel copper, Piedra Hueca copper, and Butte copper, are studied. Two groupings of the assays are used for the mean-square-successive-difference tests. One group involves an increasing sample volume by reaveraging assays to represent a longer sample intervals, the other by regrouping assays to represent longer sample intervals without a change in sample volume.

Jan 1, 1967

By Robert H. Townsend

The following paper discusses the mining, transportation, and crushing methods, with costs, at the San Andreas plant of the Calaveras Cement Co. It is one of a series, prepared for and published by the U. S. Bureau of Mine describing methods used in cement-rock quarries throughout the country. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent operating expenditures only and not total cost. It is recognized that publication of total costs mightin some instances cause embarrassment to individual producers as well as to the industry as a hole. On the other hand, operating costs are essential to the technical discussion and study of the methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost-tabulations shall ensue.

Jan 1, 1933

By John T. Metcalf

The assembly procedures for nine different wire rope terminations used in the mining industry are presented in a format and manner to facilitate training and to provide points where inspection of the termination should be performed. The nine terminations addressed are: Flemish Loop with Steel Sleeve & Thimble, Flemish Loop with Steel Sleeve, Wedge Socket, Swaged Socket, Turn Back Loop with Sleeve & Thimble, Thimble Splice with Four Tucks, U-Bolt Clip & Thimble, Zinc Poured Socket, and Epoxy Resin Poured Socket. The manual was prepared to be used primarily for field type mining operations or training where high capacity machinery is quite limited. It is nut the intent of this manual to suggest that the procedures presented are those to be used by manufacturers or other commercial enterprizes. A different set of procedures may be more appropriate where ideal space and equipment resources are available. The assembly procedures were derived from standard industrial practice, manufacturer's recommendations, and the open literature on the subject. These same procedures were used to prapare test specimens for an extensive series of pull and axial fatigue tests. The results of these tests indicate that these procedures are satisfactory in all respects. This manual is to be used as part of a complete training program. Although a brief glossary is included, there has been no attempt to make this a primer on wire rope. The selection of wire rope termination hardware, like the selection of the wire rope, is a subject not covered by this manual. The reader is cautioned that there are various sources for such hardware and this selection must be done carefully.

Jan 1, 1978

By J. T. Dunham

Zirconium has possible use in industry where severe corrosion conditions are encountered because it resists attack from a variety of corrosive environments. However, very little experimental testing has been done to evaluate the corrosion behavior of zirconium when simultaneously subjected to high tensile stresses and exposed to corrosive environments. This investigation was initiated for an evaluation test, but was limited to environments consisting of ferric chloride solutions which were known to attack zirconium and were shown to promote stress-corrosion cracking in preliminary tests. Tests for cracking susceptibility were conducted by the Bureau of Mines to show the effect of stress, solution concentration, air aeration of solution, and the method of mechanical processing. Tensile stress was applied to the specimens by a constant-load method which proved more reliable than a constant-strain method.

Jan 1, 1961

By G. Richards Gwinn

The mineral olivine, though known to mineralogists for many years, was of little commercial value in the United States before 1933. It was first described in 1790 by Johann Gottlieb Werner, who named it "olivine in allusion to its olive-green color. Commercial olivine first attracted attention because of its refractory properties. Further research has developed methods of extracting the magnesia content for the production of various magnesium compounds. Experimental and pilot-plant work also are in progress to make olivine available as a low-cost raw material for the production of magnesium metal.

Jan 1, 1943

By T. W. Johnson

The United States Bureau of Mines, in cooperation with the Natural Gas Department of the American Gas Association, has been studying actively for the past-several years the flow of natural bas through high--pressure pipe lines.4 This report deals with that part of the study involving the design of pipe-line, systems consisting of lines laid parallel to each other. The lines are deferred to as the original line and the parallel line. The paralleling line may or may not extend the entire length of the original line; however, the parallel line is, connected at its two ends to the original line. As a result of the large expansion of the natural-gas industry almost all markets within economic distance from the developed gas fields have at least one pipe line supplying them with natural gas. Small increases in the consumers' demand for natural gas can be met usually by increasing operating pressures, but any marked increase in demand necessitates paralleling sections of the existing systems. It is believed that to a large extent future

Jan 1, 1934

By J. William Ganser

This paper is one of a series being prepared by the United States Bureau of Mines describing mining and milling methods and costs at cement-plant quarries throughout the United States. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent local operating expenditures only and not total production costs. It is recognized that publication of total production costs may in some instances cause embarrassment to individual producers as well as to the industry as a whole. On the other hand, operating costs are essential to the technical discussion and study of methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations shall ensue.

Jan 1, 1931

By P. S. Haury

"INTRODUCTION Many ore deposits were discovered in the Wallapai Mining District, which covers the Cerbat Range in Mohave County, Ariz., during the early period of mining there from about 1865 to the 1890's. A considerable amount of production was obtained from shallow lead carbonate ores that carried considerable gold and silver.Mining was revived in 1906 and again during the First World War, and soma of the mines were deepened into the underlying sulfide zone. Substantial quantities of metal were recovered from two mines, the Golconda and the Tennessee-Schuylkill, that were, developed to depths of 1,600 and 1,400 feet, respectively. The Golconda is credited with $6,500,000 gross productions. 2/ This mine was not operated after 1917. The Tennessee-Schuylkill is still operating after a yield of about 300,000 tons of ore that averaged 4.33 percent lead and 7.74 percent zinc and contained an appreciable amount of gold and silver.Many of the old mines were reopened in 1942 or 1943 under the stimulus of premium prices for lead and zinc. A large proportion of this work was finished with loans from the Reconstruction Finance Corporation. It was believed that a good deal of lead and zinc could be recovered from the mines if a custom mill for concentration of the ores was available locally."

Aug 1, 1947

By GEORGE S. POPE

The Government of the United States annually expends approximately $8,000,000 for coal. Prior to 1906, this coal was purchased mainly on its reputation, or trade name, rather than under contracts specifying the heating value of the coal, its contents of ash and moisture, and other characteristics. In recent years the Government and other large consumers have appreciated more and more the desirability of definitely determining by chemical analyses and tests the character and quality of coal deliveries. Studies of engineroom and boiler-room efficiencies and economies point forcibly to the necessity of devoting more thought to the improvement of the boiler-room end. This calls for an intimate knowledge of the character and quality of the fuel used. The analyses and tests of delivered coal furnish such data, whereby the power-plant results can be comprehensively studied and a continuous check maintained on the coal and on the conditions of plant operation. Under authority of acts of Congress making appropriations for analyzing and testing fuels belonging to or for the use of the United States Government, a laboratory is maintained at the headquarters of the Bureau of Mines, 'Washington, D. C., where samples representing deliveries of coal purchased for Government use are analyzed and tested. The Bureau of Mines has been active in promoting the purchase of coal by the Government under specifications,a that is, by contracts that make definite requirements regarding the heating value of the coal expressed in British thermal units, and the composition as shown by proximate analysis. Under many of these specification contracts the bidders guarantee the quality of the coal offered, and that guaranteed by the successful bidder becomes the standard of his contract. The deliveries are sampled and analyzed to determine whether the coal is of the quality guaranteed by the contractor, and if it is not, the price to be paid is decreased in proportion; but if the coal is of higher quality, the price is proportionately increased. The analyses of coals or the guaranties offered by the bidders may in some cases be used for determining the award of a contract, but if the coals offered are of widely different characteristics, it may be difficult to determine which would prove the cheapest fuel, without having their relative evaporative efficiencies. Hence, it may be necessary to conduct evaporative tests under service conditions in order to determine which coal is particularly adapted for successful and economical use in the plant. But once a particular coal is selected, regardless of the procedure of determining the award of a contract, then the greatest advantage of the specification method is realized, in that it guarantees to the purchaser coal of uniform character and quality, thereby insuring the best results in the plant. The cost of purchases, under such specifications, of fueL for the use of the Government now aggregates approximately $4,100,000 per annum, and the cost of additional fuel for which samples are taken and submitted to the Bureau of Mines for analysis in order to determine the character and quality of the coal furnished aggregates some $3,000,000 per annum more. In fact, information is now obtained regarding the quality of fuel purchased on almost all contracts large enough to warrant sampling and analysis and heatingvalue tests. It may be said that the purchase of coal under specification is still in the stage of evolution and development, and that experience and time will be required to develop fully standard specifications and methods of sampling and analysis that may be used universally. The success of the specification method for the purchase of coal and the reliability of analysis now rests almost entirely on sampling.a Improper sampling leads to controversies, with resulting condemnation of the specification method in general and the value of laboratory analyses and tests in particular. A number of bulletins b have been published showing the results of the purchase of coal by the Government under specifications. This bulletin is a compilation of the results of coal analyses by the Government, including those made in the fiscal years 1908-1910, which have been previously published, and later analyses representing coals analyzed during the fiscal years 1911-1915. The preceding bulletins gave individual analyses or average monthly analyses, whereas this bulletin gives the average analyses only for the entire contract. It is hoped that this compilation of a series of comparable analyses of the coals purchased by the Government will be of value alike to coal dealers, to Government engineers, to purchasing agents, and to all users of coal.

Jan 1, 1916

By Haskiel R. Shell

Methods of chemical analysis of clays for the following constituents are presented: moisture, ignition loss Fe2O3, TiO2, P2O5, CaO, MgO, Na2O, K2O, total. carbon, carbonate carbon total sulfur, soluble salts, and soluble sulfate. In these procedures the attainment of accuracy has been the primary consideration sample was taken to insure accuracy, with ordinary precautions. The procedures may therefore be somewhat somewhat and will not be suited for routine work on samples for which the approximate analysis is already known and in which the need for accuracy is not very exacting. However, the method shod be as a set of detailed directions, that have been tested and shown to yield accurate results with clays and other aluminum silicate minerals. Among these minerals are clays of all types, bentonite bauxite, shale, brick; soil, calcined refractory, and sand. Although some of the methods are Unusual, no particular claim is laid to originality. The material was drawn frail many sources, put together and tested.

Jan 1, 1949

By W. R. Herrera

A research effort was conducted to present or develop methodology for evaluating candidate potting materials intended for use in explosion-proof enclosures. The primary purpose was to develop acceptance guidelines based on arc decomposition products. Acceptance criteria can be based on: ? Inherent thermo-chemophysical, mechanical and electrical properties; ? Arc decomposition products: ? Nature of volatile products produced, e.g., flammability, explosivity, synergistic effects on existing environment in the enclosure, toxicity; ? Quantity produced as a function of arc power and duration; ? Acceleration aging tests to evaluate breakdown under electrical stress.

Jan 1, 1982

By D. R. Tweeton

The U.S. Bureau of Mines has developed tomographic computer programs for geophysical applications and is distributing them as part of a Bureau plan to facilitate the transfer of technology to potential users. These programs were developed for predicting and monitoring the flow pattern of leach solution during in situ mining. The Bureau has also applied them to assessing high-wall blast damage and examining the integrity of mine-related geological structures. This report describes the curved ray program BOMCMTR (Bureau of Mines curved ray tomographic reconstruction), tells how to run it, and gives examples with synthetic and field data. BOMCRATR provides optional mathematical constraints to counteract the nonuniqueness of tomographic reconstructions with crosshole data. These constraints include limiting the maximum and minimum velocities, fixing the velocity at any point to any value, and establishing layers in which velocity does not vary with horizontal position. The user can test for nonuniqueness by varying the initial velocity pattern, The program can perform either curved or straight ray analysis. Ray paths are calculated analytically in triangular pixels, which is faster than incremental numerical approximations,

Jan 1, 2010

By Bernard S. Covino

The Bureau of Mines is conducting a study of methods to improve the efficiency of the process used to pickle stainless steels. A review of the literature on pickling of stainless steels showed that the chemistry of several process operations involved in the pickling of stainless steels is not fully understood, and that further research could improve the pickling efficiency. The benefits of this research would be a reduction in the annual loss of several thousands of tons of critical minerals such as nickel and chromium, and a reduction in the amount of solids and spent acid solution that are currently discarded. The conclusion from this review is that further research is needed in four operations that either directly or indirectly influence the pickling process: hot working, annealing, conditioning, and the actual operation of pickling, Laboratory studies of the pickling operation are presently in progress.

Jan 1, 1984